Related
hello, i followed the tutorial from this site to increase my memory on my ace 2 x, and now it bootloops and i cant get it to go into recovery or download mode... it either just turns on for a sec and reboots, or if i hold vol up it loads the "samsung gt-s7560m" screen for a sec, and thats about it... could someone please help, thanks
slickwidnick said:
hello, i followed the tutorial from this site to increase my memory on my ace 2 x, and now it bootloops and i cant get it to go into recovery or download mode... it either just turns on for a sec and reboots, or if i hold vol up it loads the "samsung gt-s7560m" screen for a sec, and thats about it... could someone please help, thanks
Click to expand...
Click to collapse
swapping kills memory card brother
also try to flash stock rom through odin
also try flashing stock rom without any sd card in slot
if you are not able to do so then i think your ace 2 is bricked
slickwidnick said:
hello, i followed the tutorial from this site to increase my memory on my ace 2 x, and now it bootloops and i cant get it to go into recovery or download mode... it either just turns on for a sec and reboots, or if i hold vol up it loads the "samsung gt-s7560m" screen for a sec, and thats about it... could someone please help, thanks
Click to expand...
Click to collapse
Hm, you can use download mode as long as the SBL is booting (as you can see by the boot logo)...
Maybe try factory mode (usb jig)?
Ryccardo said:
Hm, you can use download mode as long as the SBL is booting (as you can see by the boot logo)...
Maybe try factory mode (usb jig)?
Click to expand...
Click to collapse
Yeah, I've ordered a USB jig, so I'll try that when it comes if I don't find a solution before..
I can't get it to boot into download mode or recovery, so I don't know how I'd be able to flash with Odin..
I have been able to get odin to recognize it once in a while by messing around with different 3 button combinations, but when I press start on Odin, it just sits at "setup connection"
slickwidnick said:
Yeah, I've ordered a USB jig, so I'll try that when it comes if I don't find a solution before..
I can't get it to boot into download mode or recovery, so I don't know how I'd be able to flash with Odin..
I have been able to get odin to recognize it once in a while by messing around with different 3 button combinations, but when I press start on Odin, it just sits at "setup connection"
Click to expand...
Click to collapse
i am still waiting on these usb jigs to show up in the mail... frustruating...
the jig
slickwidnick said:
i am still waiting on these usb jigs to show up in the mail... frustruating...
Click to expand...
Click to collapse
okay, so i finally got the usb jigs in the mail, and so i put a battery in the phone, plug in the jig, and all it does is light up the screen for a few seconds then shuts off and repeats endlessly. but i noticed that if i plug the jig in for a quick second, i see the samsung screen where it says the model number but then it shuts off. now if i press power agian without removing the battery, the samsung screen with the model number comes up again, but the phone still shuts off after a couple of seconds... i dont know what to make of it...
Hard bricked, send back to Samsung and play dumb or see if one of those "we unlock all phones - international sim cards - cheap accessories" places can reflash it with JTAG
Ryccardo said:
Hard bricked, send back to Samsung and play dumb or see if one of those "we unlock all phones - international sim cards - cheap accessories" places can reflash it with JTAG
Click to expand...
Click to collapse
Okay, thanks a lot, I appreciate the help. Any idea how much one of those jtag systems cost, and which system I would need to get? I mess around with phones all the time and if it's not too expensive, it'd be handy to have around in case of future hard bricks...
slickwidnick said:
Okay, thanks a lot, I appreciate the help. Any idea how much one of those jtag systems cost, and which system I would need to get? I mess around with phones all the time and if it's not too expensive, it'd be handy to have around in case of future hard bricks...
Click to expand...
Click to collapse
I've quicky googled them a month ago and they appear to be about 70 € IIRC, and if you're serious about them remember that having a complete dump of the exact phone you have will make it 100% unbrickable
Ryccardo said:
I've quicky googled them a month ago and they appear to be about 70 € IIRC, and if you're serious about them remember that having a complete dump of the exact phone you have will make it 100% unbrickable
Click to expand...
Click to collapse
By unbrickable you mean that I'll always be able to reflash it and revive it? Or that it won't be able to be bricked again? And I noticed many different jtag systems on eBay, which one would you suggest that I get?
slickwidnick said:
By unbrickable you mean that I'll always be able to reflash it and revive it? Or that it won't be able to be bricked again? And I noticed many different jtag systems on eBay, which one would you suggest that I get?
Click to expand...
Click to collapse
Oh, the first
Basically, since you can read and write all the flash through it, just create a full dump when it's working and restore it when you hardbrick or... uh, get no display in recovery and want to fix it quickly :laugh: (for anything else flashing with Odin is probably quicker)
From what I've read RIFFBox is one of the most popular ones https://www.youtube.com/watch?v=5TTjZgQYRfw, it's probably a little overpriced for what it is but it's aimed at the "professional" market of those independent service shops...
So I broke my screen kept it lying around for 24 months then finally got it fixed this week
After replacement my power button doesn't wake up the screen at once
prolly press 20 times before it wakes up
The capacitive buttons light up on each press and even vibrates with fingerprint but screen stays off
It works fine in twrp lock screen. Locks and wakes up properly there.
The repair guy said that it's a software problem so he'll software reset it for for me I send it back
just clean flash havoc os latest but still the same problem
DrDarthZ said:
So I broke my screen kept it lying around for 24 months then finally got it fixed this week
After replacement my power button doesn't wake up the screen at once
prolly press 20 times before it wakes up
The capacitive buttons light up on each press and even vibrates with fingerprint but screen stays off
It works fine in twrp lock screen. Locks and wakes up properly there.
The repair guy said that it's a software problem so he'll software reset it for for me I send it back
just clean flash havoc os latest but still the same problem
Click to expand...
Click to collapse
you have to flash caesium kernel as he probably replaced screen with cheap version not real one,so flash this https://github.com/msfjarvis/oneplus3/releases/tag/CalumniousCarambola its the top one if on pie rom and u will be good
thanks that worked, but why does only this kernel work ?
ireaper4592 said:
you have to flash caesium kernel as he probably replaced screen with cheap version not real one,so flash this https://github.com/msfjarvis/oneplus3/releases/tag/CalumniousCarambola its the top one if on pie rom and u will be good
Click to expand...
Click to collapse
Can I install this kernel on latest OOS?
Hey guys
My ONEPLUS 3 display got broke down.
So I went for a display replacement in service centre.
For which they charged me 7500/- ₹
But after replacement.. the phone is crashig a lot.
I need to press power button end number of times & still the phone won't respond.
I don't know why this is happening.
Can someone suggest a solution?
Currently the device is on - Oxygen OS 9.0.5 (non-rooted)
Please help! ?
please try and unbrick your device by downloading this tool https://androidfilehost.com/?fid=6006931924117936392 then run msm download tool as administrator
kallum7 said:
please try and unbrick your device by downloading this tool https://androidfilehost.com/?fid=6006931924117936392 then run msm download tool as administrator
Click to expand...
Click to collapse
will this wipe device internal storage??
Lucifer213_ said:
will this wipe device internal storage??
Click to expand...
Click to collapse
yes
kallum7 said:
yes
Click to expand...
Click to collapse
what about caseium kernel?
someome told me to install it..but im not sure if it supports oxygen os latest build.
Lucifer213_ said:
what about caseium kernel?
someome told me to install it..but im not sure if it supports oxygen os latest build.
Click to expand...
Click to collapse
nope because the system drivers are corrupt so it needs to be reset by unbricking the device
ok thanks, but can u explain me the steps , cause i don't exactly know how to unbrick. Cause I've never done so.
I don't want anything wrong to happen.
Lucifer213_ said:
ok thanks, but can u explain me the steps , cause i don't exactly know how to unbrick. Cause I've never done so.
I don't want anything wrong to happen.
Click to expand...
Click to collapse
Firstly download the unbrick tool I have sent you through the link then switch off your phone and make sure cable is unplugged then hold the volume up button on your phone and then plug in the USB cable to the computer and phone then on your computer and open device manager and make sure under ports it says Qualcomm 9 and then extract the unbrick tool then run mam as admin then click start
Lucifer213_ said:
ok thanks, but can u explain me the steps , cause i don't exactly know how to unbrick. Cause I've never done so.
I don't want anything wrong to happen.
Click to expand...
Click to collapse
This has a collection of unbrick tools and versions of OOS.
This contains detailed instructions also.
Hope you solve your problem.
If not and you still have warranty for the display (OnePlus gives atleast 3 months warranty on replacement), take the phone to the Service Center. In fact, if you have warranty, that should be the first option.
Thanks for the response.
But I don't think my device is bricked, cause the phone is on working mode, but it's just that whenever I lock my phone.. It does not gets unlock on the first attempt. I need to press the unlock/power button end number of times & the phone still don't responds. It gets crashed and the System UI error occurs & asks for force stop & the phone is lagging a lot. I can't even use it properly.
I would still recommend doing it
have you got it sorted
kallum7 said:
have you got it sorted
Click to expand...
Click to collapse
I'll do it today/tomorrow
& Share the details.
kallum7 said:
have you got it sorted
Click to expand...
Click to collapse
I completed the process.
But it's still happening.
Not that much. But it is happening every 5th time I try to unlock my phone.
By this point you have two options get another device or get your op3 and take it to a OnePlus service center and get it repaired
kallum7 said:
By this point you have two options get another device or get your op3 and take it to a OnePlus service center and get it repaired
Click to expand...
Click to collapse
OnePlus service is worse.
I guess I need to purchase a new smartphone then, or find some other solution.
So my phone is stuck on this issue. I haven't done anything wrong. My phone was just peacefully charging then the phone switches off by itself then the bootloop happened.
This showed on the screen:
dm-verity corruption
your device is corrupt.
it can't be trusted and my not work properly.
press enter button to continue.
Or, device will power off in 5s.
(written in white)
Although it does turn off by itself if I ignore it, after I turn it on again and press enter or power button it boot until lockscreen and if I try to do something like unlocking, scrolling down notifs bar, and sliding through different page on home screen it will turn off again. It seem like it's crashing. The thing is I am not trying to root or flash something. I haven't done anything on my phone. I only have one phone and I badly need your help. I hope wiping or reformatting the phone is my last resort. My phone is updated to Android 11 and lateset MIUI (provided by the system itself and not downloaded somewhere). Thank you.
Well seems like something is corrupt.
It reboots when you touches the screen(or do anything)?
LR7875 said:
It reboots when you touches the screen(or do anything)?
Click to expand...
Click to collapse
It's more like it turns itself off again and if I try to press again power button if the problem show again, same thing happen. Sometimes MIUI logo appears and shuts down again it can't even go to lock screen.
Is there any chance you can unlock it?
It seems like your internal storage is corrupted.
LR7875 said:
Is there any chance you can unlock it?
It seems like your internal storage is corrupted.
Click to expand...
Click to collapse
At some point I did manage to unlock it but it happened only once and when I tried to open the notifs by scrolling down or tried to different part of homescreen it just shuts down. After that, it can't even go to the lockscreen after reboot. It's a never ending cycle. I can go to fastboot mode but I don't know if I can do miracle with that.
Well immediately plug into a computer and pull photos amd videos from it if you get it unlocked.
LR7875 said:
Well immediately plug into a computer and pull photos amd videos from it if you get it unlocked.
Click to expand...
Click to collapse
I reformatted it hoping that it will fix the problem. I was wrong. *sigh*
hyung_z said:
I reformatted it hoping that it will fix the problem. I was wrong. *sigh*
Click to expand...
Click to collapse
Well most likely your EMMC internal storage chip went bad R.I.P. (well maybe you sending those emojis will be more appropriate, but, oh well)
Maybe search more on google, I can't help you more
LR7875 said:
Well most likely your EMMC internal storage chip went bad R.I.P. (well maybe you sending those emojis will be more appropriate, but, oh well)
Maybe search more on google, I can't help you more
Click to expand...
Click to collapse
Do you think service center can help me with this or they'll probably just say to replace the phone if a bad chip is the case?
Maybe they will replace the motherboard with some fee. Or they will try to convince you to buy a new fancy phone just purely because xiaomi could earn more.
Thats all about luck (and problem is on xiaomi side, not your fault)
what's the smartphone model?
Redmi note 8 pro is the OP's phone.
Wait Wait just found some interesting lead.
Xiaomi needs a better way to unbrick its devices instead of Authorized Mi Accounts
Xiaomi has locked down the EDL mode on all of its devices, making it nigh impossible to unbrick a device without an Authorized Mi Account. Read on for more!
www.xda-developers.com
Patched SP flash tool!
heh, i have the same phone. reflash yours with the firmware that was on it before everything that happened. but don't flash userdata if you want your data on it
flashing it is simple process
LR7875 said:
Redmi note 8 pro is the OP's phone.
Wait Wait just found some interesting lead.
Xiaomi needs a better way to unbrick its devices instead of Authorized Mi Accounts
Xiaomi has locked down the EDL mode on all of its devices, making it nigh impossible to unbrick a device without an Authorized Mi Account. Read on for more!
www.xda-developers.com
Patched SP flash tool!
Click to expand...
Click to collapse
there is already a way to flash it with SPFT without authorization
also he must try to flash it in fastboot because it's not bricked
AsyJAIZ said:
there is already a way to flash it with SPFT without authorization
also he must try to flash it in fastboot because it's not bricked
Click to expand...
Click to collapse
He probably doesn't have his bootloader unlocked.
Fastboot OEM unlock wont work as oem unlock is probably not enabled in settings dev options.
LR7875 said:
He probably doesn't have his bootloader unlocked.
Fastboot OEM unlock wont work as oem unlock is probably not enabled in settings dev options.
Click to expand...
Click to collapse
ok i got it, then he should somehow put it in download mode...
Do you guys think I need to go to the service center because I don't know what to do. I really don't want to brick my phone. But a while ago my phone booted. I set it up just like buying a new phone but after I finished setting up, I just wait for the phone to catch up because I was afraid the phone will just shut down suddenly. And then, it happened again the phone shut downs without me doing anything. Now I tried to boot it up again but it is currently stuck at Redmi logo (plus "powered by android" at the bottom").
hyung_z said:
Do you guys think I need to go to the service center because I don't know what to do. I really don't want to brick my phone. But a while ago my phone booted. I set it up just like buying a new phone but after I finished setting up, I just wait for the phone to catch up because I was afraid the phone will just shut down suddenly. And then, it happened again the phone shut downs without me doing anything. Now I tried to boot it up again but it is currently stuck at Redmi logo (plus "powered by android" at the bottom").
Click to expand...
Click to collapse
SPFT enables when phone is a brick, so there's no need in service center.
they will flash it like we are going to do
Help, does anyone know how to fix dm-verity corruption? I was using my tab normally, then it suddenly shuts down and this error keeps popping up whenever my device boots. It goes on a loop unless I press the power button again.
deleted
Hello,
In the rush of flashing the january update I've flashed by mistake the Pixel 5 image bootloader (my wife's phone)
Yest that's stupid, I've done this every months for years with several Pixel phones, but I was listening to music at the same time and did dl the wrong image...
Anyway my phone is now hard bricked but I'm sure there must be a way to enter the other bootlader slot and/or entering a special recovery tool.
I cannot enter bootloader anymore
Requesting some help as I'd avoid to send it for a reflash...
Thanks !
Try: https://pixelrepair.withgoogle.com/carrier_selection
(I've never personally used this)
foobar66 said:
Try: https://pixelrepair.withgoogle.com/carrier_selection
(I've never personally used this)
Click to expand...
Click to collapse
Unfortunately the phone is supposed to have a working bootloader
Thibale said:
Unfortunately the phone is supposed to have a working bootloader
Click to expand...
Click to collapse
Ouch ...
Thibale said:
Unfortunately the phone is supposed to have a working bootloader
Click to expand...
Click to collapse
Android Flash Tool
flash.android.com
Also doesn't work?
Morgrain said:
Android Flash Tool
flash.android.com
Also doesn't work?
Click to expand...
Click to collapse
Nope...
Thibale said:
Nope...
Click to expand...
Click to collapse
Can you still access Fastboot Mode?
(pressing and holding both Power and Volume Down simultaneously. You should see a green android on his back)
Morgrain said:
Can you still access Fastboot Mode?
(pressing and holding both Power and Volume Down simultaneously. You should see a green android on his back)
Click to expand...
Click to collapse
No that's the problem.
But there are 2 bootloader slots (a and b) and I'm pretty sure there is way to switch from one to another with a special tool or button sequence.
I've already tried many button combinaison with no luck.
This kind of error is so stupid that I hope there is a way to force a rescue bootloader or something on boot.
yes but you need to be able to communicate with your phone from your pc.....if you cant access fastboot then how will you change partition?
Thibale said:
No that's the problem.
But there are 2 bootloader slots (a and b) and I'm pretty sure there is way to switch from one to another with a special tool or button sequence.
I've already tried many button combinaison with no luck.
This kind of error is so stupid that I hope there is a way to force a rescue bootloader or something on boot.
Click to expand...
Click to collapse
The only special tools we have are either the pixel repair tool or the android flash tool. If both can't get you fastboot / firmware flashing, that's it. Hardbrick. Google Pixels don't have "special" hardbrick solving tools, like older OnePlus had. You need to contact Google.
Ok I'll get in touch with my local reseller on Monday then...
Thibale said:
Ok I'll get in touch with my local reseller on Monday then...
Click to expand...
Click to collapse
Do you remember what went wrong?
EDIT: Uh, never mind. So you accidentally used the P5 fw. Why on hell would the device accept the P5 fw at all?!
Same problem here: downloaded from a blog the latest firmware. They have linked the pixel 5 firmware and named it as Pixel 6 pro full firmware. Just flashed without looking and now the phone wont boot. No reaction at all, no fast boot or whatsoever. Have filled in a repair request in my google account, because I’ve bought it directly in their store.
Do you think they have a way to find out what went wrong? I meant the phone is not giving any signal, regardless of which button combination I press. Worst case: I have to pay for the repair…
Psfanboy88 said:
Same problem here: downloaded from a blog the latest firmware. They have linked the pixel 5 firmware and named it as Pixel 6 pro full firmware. Just flashed without looking and now the phone wont boot. No reaction at all, no fast boot or whatsoever. Have filled in a repair request in my google account, because I’ve bought it directly in their store.
Do you think they have a way to find out what went wrong? I meant the phone is not giving any signal, regardless of which button combination I press. Worst case: I have to pay for the repair…
Click to expand...
Click to collapse
WOW. So even holding volume down and power until you see the fastboot screen wont work? sometimes you have to hold it for a while. I say that because when the December firmware came out I accidentally flashed the wrong region but was able to access bootloader and so was able to rescue myself. So sorry dude. That really sucks.
Psfanboy88 said:
Same problem here: downloaded from a blog the latest firmware. They have linked the pixel 5 firmware and named it as Pixel 6 pro full firmware. Just flashed without looking and now the phone wont boot. No reaction at all, no fast boot or whatsoever. Have filled in a repair request in my google account, because I’ve bought it directly in their store.
Do you think they have a way to find out what went wrong? I meant the phone is not giving any signal, regardless of which button combination I press. Worst case: I have to pay for the repair…
Click to expand...
Click to collapse
Yes worst case we'll have for repair but they could have implemented a simple device id check on their script prior flashing anything, especially for the bootloader.
Anyway, I'm alive, in a good health and it's just a phone
niko26 said:
Do you remember what went wrong?
EDIT: Uh, never mind. So you accidentally used the P5 fw. Why on hell would the device accept the P5 fw at all?!
Click to expand...
Click to collapse
You can flash gobbledygook to your phone if you're not careful. You can flash a non-Google phone's image. Flashing just flashes what you tell it to flash.
Psfanboy88 said:
Same problem here: downloaded from a blog the latest firmware. They have linked the pixel 5 firmware and named it as Pixel 6 pro full firmware. Just flashed without looking and now the phone wont boot. No reaction at all, no fast boot or whatsoever. Have filled in a repair request in my google account, because I’ve bought it directly in their store.
Do you think they have a way to find out what went wrong? I meant the phone is not giving any signal, regardless of which button combination I press. Worst case: I have to pay for the repair…
Click to expand...
Click to collapse
That sucks. I'm sure you know now, always go straight to the source for everything if possible, firmware, platform tools, drivers, BIOS / UEFI (for computer).
SDK Platform Tools
Get the Google USB Driver
Pixel 6 Pro Factory Images
You can also Google for official pixel firmware and the top search result is what the want. I know it doesn't help you now. Good luck with your phone!
Morgrain said:
After having played around with the January patch (came from December Europe A4 firmware that was pulled), it seems that the FP scanner got even faster and more reliable, even though it's not stated in the patchnotes. Maybe it's just placebo.
Click to expand...
Click to collapse
So many folks have reported the exact same thing, I'm really, really curious just how much faster it will seem when I get around to updating.
roirraW edor ehT said:
So many folks have reported the exact same thing, I'm really, really curious just how much faster it will seem when I get around to updating.
Click to expand...
Click to collapse
I noticed how faster it was before I saw everyone else posting about it, so at least no placebo on my end. Hope you find the same.
I know that you tried to get into Fastboot. Pixel 6/6P also has a Recovery mode. I can get to it from a working phone.
I would think that there is someway to boot into Recovery mode from a dead phone via button combos.
Thibale said:
Hello,
In the rush of flashing the january update I've flashed by mistake the Pixel 5 image bootloader (my wife's phone)
Yest that's stupid, I've done this every months for years with several Pixel phones, but I was listening to music at the same time and did dl the wrong image...
Anyway my phone is now hard bricked but I'm sure there must be a way to enter the other bootlader slot and/or entering a special recovery tool.
I cannot enter bootloader anymore
Requesting some help as I'd avoid to send it for a reflash...
Thanks !
Click to expand...
Click to collapse
Hy, how did you flashed? Via adb sideload or?
vrda08 said:
Hy, how did you flashed? Via adb sideload or?
Click to expand...
Click to collapse
factory image with modified flash-all.bat
I'll do the exact same process when I'll get my phone back but this time I'll check the image name at least 3 times
My device went into brick while flash android14 fail .At the beginning,it can boot to fastboot mode,but now it's no response at all& can't get into fastboot.The google help center need original purchase email ID for further help,i can't find it due to I bought the pixel6 pro from second hand market .
How to rescue the pixel6pro brick without fastboot?
Google pixel flash tool online and boot into fast boot follow instructions and you should be able to bring it back
Here's the link:
Android Flash Tool
flash.android.com
thelostsoul89 said:
Google pixel flash tool online and boot into fast boot follow instructions and you should be able to bring it back
Here's the link:
Android Flash Tool
flash.android.com
Click to expand...
Click to collapse
thanks for your advice,but the device can't boot to fastboot mode
ok6669 said:
thanks for your advice,but the device can't boot to fastboot mode
Click to expand...
Click to collapse
I apologize your original post said that it can... not that it can't
thelostsoul89 said:
I apologize your original post said that it can... not that it can't
Click to expand...
Click to collapse
thelostsoul89 said:
I apologize your original post said that it can... not that it can't
Click to expand...
Click to collapse
^_^
Can you boot into the recovery? You could sideload an ota
Code:
adb sideload "path to ota.zip"
Tip: right click on the ota.zip and select 'copy as path' and paste it
fil3s said:
Can you boot into the recovery? You could sideload an ota
Code:
adb sideload "path to ota.zip"
Tip: right click on the ota.zip and select 'copy as path' and paste it
Click to expand...
Click to collapse
nope,brick deeply
ok6669 said:
My device went into brick while flash android14 fail .At the beginning,it can boot to fastboot mode,but now it's no response at all& can't get into fastboot.The google help center need original purchase email ID for further help,i can't find it due to I bought the pixel6 pro from second hand market .
How to rescue the pixel6pro brick without fastboot?
Click to expand...
Click to collapse
Did you hold power and volume up for 15-30 seconds? Also, did you try and charge it? Could be dead
Let's put it this way, you're phone won't awaken until it's internal signature can be re verified. It uses ACM as an initial protocol then goes into a serial gadget mode. At the current moment someone straight up stole my Pixel 6 or else I would still be working on a unbrick solution. If anyone's willing to donate a bricked one I'm all for putting in the effort to continuing development.
The nature of the dead brick is to ensure that no data on your phone can be compromised. So the the method to unbricking also requires you to a sort of NAND erase, as seen on previous Exynos devices. I had just gotten all the tools set up and even made my own ACM handshake in coordinance with the Open Source Vendor Code and someone just decided, oh hey, look it's a nice phone let's take it. And now I have to continue making payments on it. Life sucks sometimes.
NonStickAtom785 said:
Let's put it this way, you're phone won't awaken until it's internal signature can be re verified. It uses ACM as an initial protocol then goes into a serial gadget mode. At the current moment someone straight up stole my Pixel 6 or else I would still be working on a unbrick solution. If anyone's willing to donate a bricked one I'm all for putting in the effort to continuing development.
The nature of the dead brick is to ensure that no data on your phone can be compromised. So the the method to unbricking also requires you to a sort of NAND erase, as seen on previous Exynos devices. I had just gotten all the tools set up and even made my own ACM handshake in coordinance with the Open Source Vendor Code and someone just decided, oh hey, look it's a nice phone let's take it. And now I have to continue making payments on it. Life sucks sometimes.
Click to expand...
Click to collapse
I think you are the one unbrick the pixel 6pro who is the most closest.i fell that you are very humor person.Life can't be as good as you think, but it won't be as bad as you think
So I have the same problem. It restarted and said something about your files are corrupt and cannot be trusted. I got it to boot to bootloader, used android tool online and it did the same thing. Now I cannot get the phone to turn on at all. So now I need help please!!! I cannot afford to buy a new phone currently.
did you try plugging in for 30 mins? If can’t boot to anything after that, only Google can fix it.
Arealhooman said:
did you try plugging in for 30 mins? If can’t boot to anything after that, only Google can fix it.
Click to expand...
Click to collapse
Yeah Google's fix is $600. Which is ridiculous. I had it plugged in all day, now I just have it sitting on my dresser hopefully it will just start on it's own. I don't know what else to try. I tried pressing the power button for 60 seconds. I tried power volume up for 60 seconds. I tried power button volume down for 60 seconds. Nothing seems to work. Yet if I plug it in to my laptop, you can hear the ding as if it connected. So I don't know what to think.
Jdemio said:
Yeah Google's fix is $600. Which is ridiculous. I had it plugged in all day, now I just have it sitting on my dresser hopefully it will just start on it's own. I don't know what else to try. I tried pressing the power button for 60 seconds. I tried power volume up for 60 seconds. I tried power button volume down for 60 seconds. Nothing seems to work. Yet if I plug it in to my laptop, you can hear the ding as if it connected. So I don't know what to think.
Click to expand...
Click to collapse
Sounds like a dead display, especially if its being recognized by a laptop
ok6669 said:
My device went into brick while flash android14 fail .At the beginning,it can boot to fastboot mode,but now it's no response at all& can't get into fastboot.The google help center need original purchase email ID for further help,i can't find it due to I bought the pixel6 pro from second hand market .
How to rescue the pixel6pro brick without fastboot?
Click to expand...
Click to collapse
If your phone is recognized as Pixel Rom recovery, then I am very sorry to you. only the official Google service will save you, or you will find the same phone with a broken screen in the trash that you can take a fee from there and put it on yourself
Jdemio said:
Yeah Google's fix is $600. Which is ridiculous. I had it plugged in all day, now I just have it sitting on my dresser hopefully it will just start on it's own. I don't know what else to try. I tried pressing the power button for 60 seconds. I tried power volume up for 60 seconds. I tried power button volume down for 60 seconds. Nothing seems to work. Yet if I plug it in to my laptop, you can hear the ding as if it connected. So I don't know what to think.
Click to expand...
Click to collapse
What is it recognized as?
Arealhooman said:
它被认为是什么？
Click to expand...
Click to collapse
pixel cdc -amc device! and then disappear
idark11 said:
If your phone is recognized as Pixel Rom recovery, then I am very sorry to you. only the official Google service will save you, or you will find the same phone with a broken screen in the trash that you can take a fee from there and put it on yourself
Click to expand...
Click to collapse
Google is not serve in our country,asking google for help is not convenient for me
ok6669 said:
pixel cdc -amc device! and then disappear
Click to expand...
Click to collapse
Pic?
Jdemio said:
Yeah Google's fix is $600. Which is ridiculous. I had it plugged in all day, now I just have it sitting on my dresser hopefully it will just start on it's own. I don't know what else to try. I tried pressing the power button for 60 seconds. I tried power volume up for 60 seconds. I tried power button volume down for 60 seconds. Nothing seems to work. Yet if I plug it in to my laptop, you can hear the ding as if it connected. So I don't know what to think.
Click to expand...
Click to collapse
i think google have the secret weapon to recover the brick pixel,it 's a simple software problem for google. a piece of cake