Hello everyone,
so here's my problem:
Wednesday morning i took my phone out of my pocket and had a blackscreen. I tried to restart it and took out the batterie but i always got stuck in the LG Logo or a bootloop. Since i had TWRP and lineage OS installed, i tried to go into the twrp menu with the factory mode (power button + volume down) but after the "double yes" i always got a blackscreen.
So i went into the internet to fix it myself. I tried the "LG Flash Tool 2014" with the kdz. reset & the other Flash tool with the tot. reset. Both didnt recognize my phone. At this point, the only thing that worked was the download mode BUT not the recovery mode that usually comes after it. It just showed the download mode for some seconds and then a black screen. Later i noticed that my phone showed as a "qualcomm device" in the device manager, and the internet said that this was bad. So i used "Board diag" and "Smart boot diag" to fix it, but at the point where the device should have restarted, and the download mode should have worked WITH the recovery mode, i always ONLY had the 6 second download mode. After messing a bit with "Board Diag" i even got it to show up as LGE AndroidNet USB Serial Port in the device manager, which apparently was even more bad and only way to go back to qualcomm was to shorten the pins which i did. And it worked BUT now i was back with the qualcomm stuff.
So as you can see, i've prety much run i circles since wednesday... Iam now at a point where 3 different thingscan happen when I try to put my LG into download mode (volume up + usb cable):
1. Its recognized as a unknown device which is constantly connecting and diconnecting, so iam assuming my phone is bootlooping with a black screen.
2. The download mode icon shows on my phone and disappears after some seconds but my pc fails to recognize it.
3. Nothing happens and the screen stays black
When i only connect the usb cable, it shows a stuck charging icon for some seconds and then goes black. Connecting without a battery shows the "missing battery icon". I tried with 2 pc's, both having the LG mobile driver 4.2 and the qualcomm driver installed AND beeing in testmode. Both don't recognize the device. I also tried 2 batteries on my phone but it changes nothing.
I have a D855. And i know that my situation is pretty f*cked but maybe someone i able to help me anyway. Thanks alot.
Hello,I recently flash a wrong file and now my device is straight up dead no logo nothing the led blinks for a mini second and turns off I tried using qfil and mi flash but it was getting detected as 900e port and wasn't even detected on mi flash I tried updating drivers and got it to 9008 but still it would get stuck forever when I hit download asap in qfil or would show some sahara port error and still no detection on mi flash even in 9008 mode I tried over 50+ times using the button combinations to get it to 9008 mode but every time it would be 900e any solution other than deep flash as I have just one type c cable and I may screw up
Press volume up key for 15 seconds, then press power button & insert usb (within a second) to pc..it will get it to edl mode..
probably your only way out is deep flashing, i've been through this
any solution for this ? i'm suffering the same
Hi im still can't unlock bootloader, anyway to enter in EDL mode?:crying:
2 Ways:
-Bricking your device on purpose (Not recomended, I discover this flashing a custom ROM on My Wife's phone without copying AB partitions.)
-Strpping a USB cable and joining D+ (Green Wire) and GND (Black Wire) for at lease 30 seconds until your phone forces EDL mode on itself and your PC detect the device as Qualcomm 9008
I hope this could be useful to you and to anyone.
i did a big mistake..i flashed redmi 6 pro rom to my a2 lite ..now nothing is happening...edl mode/fastboot mode is not accessing.i also show my phone to a service center. thaaaay just **** me they breaak my fingerprint reader.......help me to boot my phone i have to brought a back-part with finger print reader.please help me
absigma said:
i did a big mistake..i flashed redmi 6 pro rom to my a2 lite ..now nothing is happening...edl mode/fastboot mode is not accessing.i also show my phone to a service center. thaaaay just **** me they breaak my fingerprint reader.......help me to boot my phone i have to brought a back-part with finger print reader.please help me
Click to expand...
Click to collapse
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
In few words search in Google : test point mi a2 lite and do it
SubwayChamp said:
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
Click to expand...
Click to collapse
i cant access fastboot but it is connecting to edl mode but not getting flash.when its connect a sounds on pc but when not properly not in edl the notification light blinking.please help me.
Os_Herdz said:
In few words search in Google : test point mi a2 lite and do it
Click to expand...
Click to collapse
tnx bro but i know testpoint and i used that when my phones bootloader locked
SubwayChamp said:
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
Click to expand...
Click to collapse
now showing in mi flash as COM6 but when try to flash is says ''cannot read from COM6" help me
absigma said:
now showing in mi flash as COM6 but when try to flash is says ''cannot read from COM6" help me
Click to expand...
Click to collapse
How is detected under device manager? qualcomm-HS-USB qdloader 9008? Also what about behaviour of led light, it stays on all the time or it blinks?
Edit: Now I read your previous post, Led light has to blink, this is correctly connected, see under device manager how it is detected.
SubwayChamp said:
How is detected under device manager? qualcomm-HS-USB qdloader 9008? Also what about behaviour of led light, it stays on all the time or it blinks?
Click to expand...
Click to collapse
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
absigma said:
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
Click to expand...
Click to collapse
Ok, Behaviour changes depending on what rom you actually are, it´s mean that now you have flashed some partitions from Miui rom (led light will stay off) at least it´s being detected.
Things that you can try:
- Move the rom to the same folder where XiaoMi flash is.
- Rename the folder as short as better like "xiaomi" without quotes.
- Put your Windows in "Test Mode", restart to changes take effects.
- Switch to other version of the tool, it worked for me latest from here https://xiaomifirmware.com/downloads/miflashpro/
- Try with other rom version.
absigma said:
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
Click to expand...
Click to collapse
i mconnect the battery now qualcomm-HS-USB qdloader 9008 in device manager & notification is blinking
absigma said:
i mconnect the battery now qualcomm-HS-USB qdloader 9008 in device manager & notification is blinking
Click to expand...
Click to collapse
Don't worry about led behaviour, your device will turn a bit weird cause you flashed a wrong firmware, the important here is that it's recognised by pc. What about the steps, tried?
When pressed volume up and down key together and connected to pc it shows charging symbol then appears in my pc as qualcomm 9008 port then reboots .I'm trying to flash my device using qfil which needs phone to be in edl mode and my phone is not staying at edl mode so I can't flash it .Any advice will be really helpful.