Just put 13 stable on my phone and charging my phone Takes forever I mean it's slow as hell..Wasn't the best on Android 12 but hell on Android 12 it was way faster.. That's the one thing I hate about this phone the battery life sucks an charging the battery is so damn slow..I got all the Adaptive crap turned off.
I'll have to pay more attention to the charging speed on my P6P and let you know what I experience. I try to never use fast charging, never charge overnight, try not to let the battery go below 25% and don't charge past 75%. That 50% range lasts me about 24 hours, but I might use my phone less than you.
I had no complaints about the charging speed on Android 12.
Edit: I'm happy with how much my phone has charged in the last 45 minutes, given that I don't use fast charge methods.
I am having the same issue. Installed 13 stable on my 6 pro. My battery got down to 4% so I plugged it in. I continued to watch YouTube and after an hour it was only up to 8%. Something is def wrong. The battery sucked before but now it's even worse
Updated yesterday and seems ive now got an issue with wireless charging. My phone stopped charging at 81% overnight. Its very intermittent whether it starts charging now on the two wireless chargers i have and seems to stop randomly, not getting to 100%. Charges fine using a cable.
Have the same problem since upgrading to android 13.
According to AccuBattery is the charge current around 900 mA. Way too slow and really annoying!
Didn't have the problem with android 12.
I'm using an Anker Power Port III which can charge with up to 25W. It's the same with other cables and charging devices.
Edit: Attached some screenshots
To clarify one thing for a number of users, you will not get adequate charging speeds without the official charging cable, the 30W Google branded wall brick and good temperature conditions.
The temperature conditions are generally the hardest to control whilst using the device - so I always charge with my phone powered off and have never had an issue. Heck, I generally charge with a 5W wireless pad and it always reaches 100% overnight (usually takes about 5 hours with my minimal wattage charging pad).
*Edit*
In the end - with the official cable usage - my charging speed hasn't changed between A12 and A13.
NippleSauce said:
To clarify one thing for a number of users, you will not get adequate charging speeds without the official charging cable, the 30W Google branded wall brick and good temperature conditions.
The temperature conditions are generally the hardest to control whilst using the device - so I always charge with my phone powered off and have never had an issue. Heck, I generally charge with a 5W wireless pad and it always reaches 100% overnight (usually takes about 5 hours with my minimal wattage charging pad).
Click to expand...
Click to collapse
I think you didn't get my point. I did a comparison between android 12 and android 13. Since the charging speed is reduced dramatically it doesn't matter which cables or charging devices I use unless they are the same.
So we don't discuss absolute charging times here but the fact that by upgrading the OS of our Pixel 6 Pro the charging behaviour changed ceteris paribus.
I charge slowly over night, the charger i use normally charges at 1.5A max, now on A13 it is charging at 800mA
I have ESR magsafe ring. My car charger is working for about 2 minutes and stops. Battery temperature reach 43°C within 2-3 minutes since I upgraded to android 13.
All of the magsafe accessories stopped working. All of the normal QI chargers stopped working. I absolutely hate this phone. First 3 months - no reception in buildings. Still no 5G in my country even with root and signal guru. Now it's not charging wirelessly and only slow charing with cable.
My new guess is it is due to the overheating problem with the update to Android 13.
A lot of people complain about the high temperature. Therefore the phone reduces the charging speed.
Maybe that's also the reason for the problem with the wireless charging. too much heat = no wireless charging. Just guessing...
ATM I rebooted my phone to safe mode. Let's see if this helps.
Somehow I solved the problem. I booted into safe mode. Then I clean the temp files with Google Files. And now my phone is charging with 2mA and above again. Also the temp of the battery is down to 36°. I still think that is the root cause.
veeroohre said:
Somehow I solved the problem. I booted into safe mode. Then I clean the temp files with Google Files. And now my phone is charging with 2mA and above again. Also the temp of the battery is down to 36°. I still think that is the root cause.
Click to expand...
Click to collapse
Doubt this but I will try it and report back
NippleSauce said:
To clarify one thing for a number of users, you will not get adequate charging speeds without the official charging cable, the 30W Google branded wall brick and good temperature conditions.
The temperature conditions are generally the hardest to control whilst using the device - so I always charge with my phone powered off and have never had an issue. Heck, I generally charge with a 5W wireless pad and it always reaches 100% overnight (usually takes about 5 hours with my minimal wattage charging pad).
*Edit*
In the end - with the official cable usage - my charging speed hasn't changed between A12 and A13.
Click to expand...
Click to collapse
well we know for one you dont need that
just a cable capable of the current and a charger that hits PPF standards
and even with/without official chargers it will only peak 21w
im using a £5 Gan charger and a USlion 2M long magnetic 60w cable that can do data aswell and it is doing 20w peak for me on A13 which is what it did on A12 aswell. Both which i bought before the official charger came out
Paz9 said:
Doubt this but I will try it and report back
Click to expand...
Click to collapse
Nope, still charging like a piece of [crap, so,] not sure what Google did with A13 , I use official charger for fast charge, considerably slower than on A12
But yeah 3rd party Chinese charge and magnetic cable no issues. Charging issues are not a13 related it will be some defining factor like an app or hardware
CubnPackdad said:
Just put 13 stable on my phone and charging my phone Takes forever I mean it's slow as hell..Wasn't the best on Android 12 but hell on Android 12 it was way faster.. That's the one thing I hate about this phone the battery life sucks an charging the battery is so damn slow..I got all the Adaptive crap turned off.
Click to expand...
Click to collapse
I am having the same problem
I updated my pixel 5a to 13 stable. It's charging speed decreased a lot . Firstly it took around 1hr 50 min to get 100 now it's lot
more than 3hr. Gets lot of heating while charging.
Sometime it shows "6 hr to full charge" even at (30-40) battery level, and that's really bad .
After 13 Device is heating ( not just warm) so much even in normal uses (No gaming).
My own testing found out as long as battery reach 41 degree C, the P6P will charge at 3.5W only... (While still displaying fast charging). It you put the phone in front of air conditioner vent to lower the temperature to 25 degrees C, then it charging at full 20W.
The P6P easily get into battery y 41 degrees C by just charging at room temperature higher then 32 degrees C. On A12 its pretty difficult to get this... Somehow A13 drive the CPU while charging which I suspect affect the heat dispatching. I used a charging wire with watterage display so its easily see how P6P limiting the charging wattage with temperature.
It was considerably slower for me too. I was in Spain, coming from UK, so had to use adapter. I thought it's the case, but it has also been something with temperatures, I couldn't backup the pictures because the system showed me it's too hot. I hope that was the issue.
I just swith to Android 13 there are ossue with battery . please fix it .you guys are doing great work
Related
I just bought an use xl. The oem accesories were never used seems he was charging the pixel mostly in his car. Now im using the official oem charger and cable and heat up the phone like crazy. It does say rapid charging but even the time went up to 3 hour estimated time to fully charge which is crazy. Now using a galaxy s7 edge dock charge and some spare usb c cable i had the phone does not heat up,. Charge in quick charge and it take like an hour and 20 minute to fully charge..... Im i missing something here?
Charging time left is not static it changes with temperature. If your phone is already reached 42 45 degrees which generally correct it slows down charging. And also it heats up if you are using your phone during fast charging intervals which is first 20 min. Also even when you don't use it, it heats up because of wake locks (charging). Also i realize a hot climate is a factor. For oem charger it can reach 3 amps so it is normal for heating and most other chargers supply less so it does not heat up. Soo it is like a design problem you can charge your phone super fast but it will heat up so charging speed will vary but i think in the end it will still quick enough.
Why do you think they advertise quick burst charge instead of quick full charge ?
Hello!
Charging problems started to occur a month ago on my phone. The problem is that it charges really slowly, but other times normally.
I experienced that if I plug in the phone when the battery is between 20-60% it charges super slowly.
Sometimes it speeds up but more often not.
Here are some screenshots that show that sometimes it takes like 6 hours to charge and sometimes it basically just hovers around a percentage and doesnt do anything. Gets like 10% overnight.
On the second picture you can see that it charges normally till it reaches 55% then it slows down to like 5%/hour speed.
I noticed this while the phone was draining battery even tho it was plugged in while using it.
I bought a new OEM battery and its the same with it aswell. Some chargers charge it quicker, some slower, but the problem occurs with every charger.
What do you guys recommend me to do?
Thanks a lot!
is your charger 2 Ampere as it should be?
U can also try to recalibrate the battery deleting the data/system/batterystats.bin file
haget83 said:
is your charger 2 Ampere as it should be?
U can also try to recalibrate the battery deleting the data/system/batterystats.bin file
Click to expand...
Click to collapse
Thanks for the reply!
I have used many chargers since I have this problem, but mostly the one that came in the box.
Ill try deleting that file if its possible withouth root.
Edit: It seems i need root for it, so its not an option for me.
Kr3Ep said:
Thanks for the reply!
I have used many chargers since I have this problem, but mostly the one that came in the box.
Ill try deleting that file if its possible withouth root.
Edit: It seems i need root for it, so its not an option for me.
Click to expand...
Click to collapse
Actually brother initially same problem occured with me and it was persisting on the same way load since i come to change my charger now before i was charging it with blackberry passport charger it was really cool and even charges it faster that i mean around 50% faster than the previous charger, but now days m befitted with moto g4+ which meets to charge my lg g3 around 65% faster
But brother dont use any local company pr anypther charger as it may damage the phone display which may come to cost you at high
There are going to be 3 main factors that you want to address:
- Battery
- Charger/charging cable
- Software
It seems you have already addressed your battery. That's usually the #1 culprit, but you've already replaced it so you can rule that out.
The next is the charger and charging cable. This is often overlooked. The stock charger is 5 volts and 1.8 amps (5v 1.8a). Before more advanced smart phones were developed, almost all USB chargers never produced more than a 5v 1.0a charge (most were 5v 0.5a). So you want to ensure you are using at least a 5v 1.8a charger. (I even use my Fire Tablet charger on my G3 which is 5.1v 2.2a, and that works great too). Note that all USB chargers have their output volts/amps printed on them somewhere (usually in very tiny print). The USB cable you are using matters too. The thinner the wire gauge and the longer the cable is, the less power is transmitted. For example, if you're using a thin and cheap 6 foot (2 meter) USB cable on a 5v 2.0a charger, you may only be getting 1.0a of charge from it. If you use a thicker, shorter, and more expensive 3 foot (1 meter) USB cable on that same charger, you ensure you get that full 2.0a of charge (or close to it). The two factors to look for in a USB cable is length (length = resistance = less amps) and wire gauge (not insulation thickness).
The last is software. If you have any way to backup and restore (ie nandroid) your ROM from recovery, I recommend doing that first because it's easy. If you backup your current ROM, factory reset, and the issue persists then you know its the charger/cable. If the issue is gone, then you know it's something in your current ROM. If you do not have access to backup/restore features and/or do not have root, then next you can use the Android OS Battery stats to carefully go over what could possibly be draining so much power when the phone is on or off. There are also several apps that will help you determine where the battery drain is coming from. Note that software can not prevent your phone from charging, but it can drain power so fast, that there is not enough left over to charge the battery. This is especially bad for our G3s because they easily overheat if they are charging and heavily discharging simultaneously.
Hope that helps! Good luck! :fingers-crossed:
Hi,
Is it possible to turn off the dash charge? 5T is charged only overnight cause it can last the whole day anyway.
PS: I can turn off Fash Charge in my Samsung Note. So it saves battery if I charge only overnight and don't need fast charge feature.
There is no stock option for this. Maybe a custom kernel can support it or a custom kernel that doesn't support it at all would also be a possibility in theory.
I would suggest using a normal power adapter instead of the Dash charging one. Even a normal USB C cable prevents Dash charging as it can only be used with OnePlus' own cable. So maybe get a cheap USB C cable and use that?
Use a low amperage charger. Something like 1000mah. This will slowly charge your phone overnight. But make sure you use a quality charger.
Why would you want to do this? The OnePlus dash charger works differently from other chargers in that it holds the heat in the charging block. If you use a standard adapter you would transfer the heat to the phone while charging. I would NOT recommend doing this.
Sent from my ONEPLUS A5010 using Tapatalk
I use an Anker IQ 6-port Charger with a couple of fairly good quality cables.
I personally try to avoid any kind of fast charge because it will end up damaging the battery life faster than "standard" charge, even if the heat is absorbed by the DASH charger block. IQ Charge adapts itself with the needs of the device connected.
And my unit stays cool if I touch it while its charging.
Charge however you want. But for me, dash charger while getting ready in the morning or when you have a free half hour. Forget about charging overnight. I don't know your usage but for me, this works. The phone just sits on my nightstand without connecting overnight and I lose a very minimal battery amount.
Sent from my ONEPLUS A5010 using Tapatalk
---------- Post added at 05:47 PM ---------- Previous post was at 05:43 PM ----------
https://www.guidingtech.com/61180/dash-charging-quick-charge. I'll just leave this here.
Sent from my ONEPLUS A5010 using Tapatalk
That's why we can choose
Just not in a software way.
I choose to use wireless charging using a receiver.
通过我的 ONEPLUS A5010 上的 Tapatalk发言
DragonMessor said:
Use a low amperage charger. Something like 1000mah. This will slowly charge your phone overnight. But make sure you use a quality charger.
Click to expand...
Click to collapse
It's fine at even less than 1 amp. We have two 5Ts in the house and charge them at night at 0.35 - 0.45 amp.
I saw the dash reduce Ampare when pass above 80%.
(When not rush I use official iPhone 1Amp charger.)
Use 5V/2A standard charger to standard usb type c.
Oneplus 5t = 5V/4A
Quick Charge = 9V/2A
Dash n QC have more power!
I'm using an old 1A Samsung power adapter and dash charge cable and in addition I also use Battery Charge Limit app to limit charging the battery to 80%.
https://forum.xda-developers.com/android/apps-games/root-battery-charge-limit-t3557002
Headbanger1982 said:
I personally try to avoid any kind of fast charge because it will end up damaging the battery life faster than "standard" charge
Click to expand...
Click to collapse
No, it does not, especially not with dash charge. The excess heat is stored in the charger and is not transferred to the phone, and the heat is the only thing that degrades the battery faster.
SilverSurger said:
No, it does not, especially not with dash charge. The excess heat is stored in the charger and is not transferred to the phone, and the heat is the only thing that degrades the battery faster.
Click to expand...
Click to collapse
Your informations are not correct.
Dash (or VOOC, which is the very same technology since OnePlus is an Oppo brand) uses high current fast charging instead of high voltage charging (QuickCharge 2.0/3.0 uses high voltage) and the circuit that produces heat in phones that are not Dash/VOOC compliant is inside the phone, while in Dash/VOOC is inside the charger.
Oppo and OnePlush themselves have acknowledged that it makes SAFE to use the phone while it is quickcharging, NOT that the battery is not getting damaged by the use of a fast charging method, even if it charges at a lower voltage and higher current.
The use of any fast charge technology implies to shorten out the overall battery life.
SilverSurger said:
No, it does not, especially not with dash charge. The excess heat is stored in the charger and is not transferred to the phone, and the heat is the only thing that degrades the battery faster.
Click to expand...
Click to collapse
Just because they moved a bunch of the power regulation stuff to the charger doesn't mean the battery doesn't still get warmer. If you push 4 amps of current into it, it will heat up more so than when it receives, 1 amp.
Now you have me curious though, I guess I'll have to pay close attention to the battery temp next time I charge my battery. I've never used the dash charger, but perhaps I'll have to get it out of the box, and test with it as well just to see what kind of temps I see with a more powerful charger as well. I'm curious to see how much temperature difference there is.
I know on my Nexus 5X my phone always lasted long on a single charge when slow charged (0.35 amps), vs using the factory 3 amp charger.
Constantly topping up the battery overnight for 5-6 hours (assuming your slow charger will charge it to 100% in 2-3 hours) is worse than using Dash to charge it quickly in bursts in the morning and night when you have a spare 30 minutes.
I would never leave a phone stuck on a charger overnight. Especially since even the slowest charger in the works will charge the phone to 100% in three hours or so.
xocomaox said:
Constantly topping up the battery overnight for 5-6 hours (assuming your slow charger will charge it to 100% in 2-3 hours) is worse than using Dash to charge it quickly in bursts in the morning and night when you have a spare 30 minutes.
I would never leave a phone stuck on a charger overnight. Especially since even the slowest charger in the works will charge the phone to 100% in three hours or so.
Click to expand...
Click to collapse
I don't charge my phone over night either but by using above mentioned Battery Charge Limit app it is possible to stop charging when desired battery level has been reached.
Squabl said:
I don't charge my phone over night either but by using above mentioned Battery Charge Limit app it is possible to stop charging when desired battery level has been reached.
Click to expand...
Click to collapse
That would be a good idea to do. Although the best is to just Dash charge in short 30 minute bursts when you can.
Headbanger1982 said:
Your informations are not correct.
(...)
The use of any fast charge technology implies to shorten out the overall battery life.
Click to expand...
Click to collapse
How does it imply that? Heat is the only factor. Phone is not getting hot(ter than slowly charging) when charging.
What is the truth? With the rapid charging the battery deteriorates faster or better a slower charging?
I have had my S22 base for about a week, and while I am still concerned with the life I'm getting (same apps and usage pattern, about 4+ hours of SOT and 15 hours of mixed use) vs the S9, I had decided to keep it until ...
I can't get the thing to super/fast charge. I do not have a Samsung charger (waiting until I get my voucher) but do have a number of 15W and 25W PD-compliant chargers that work on everything from my S9 to my laptop. Unless I turn the phone off, all of those chargers charge S22 at a rate of 10-20% per hour, with Accubattery readings in the 200-1100 maH range, NEVER a value over that. The battery temp and voltage are well in spec. It is currently plugged into my laptop PD compliant charger at a rate of 900 mA with a "time to 100%" of 30h.
Likewise, I bought 2 car chargers that are S21 certified as well as QC3.0 and PD3.0. It has a 30W port. I used the cable that came with either charger (I've tried a ton of cables) and sometimes it gives a "0mA" reading while other times it goes 200mA-800mA at a good voltage. That means while I don't lose charge, I also don't gain. On my 30 min drive home I went from 23% to 24% with dark mode and no apps running.
Finally, to extend the mystery, depending on which aftermarket charger I use the phone itself thinks I'm Fast Charging or Super Fast Charging, reporting that on the lock screen and battery screen. On that screen it says something like 30m to 100% even though the observed charge rate is much lower.
Samsung won't talk to me unless I'm using a Samsung charger and I can't wait until I get the voucher/those are in stock ... I have 5 days to return it and unless you can help me (Obi Wan) I'll be back on that track.
icewiz1 said:
I can't get the thing to super/fast charge. I do not have a Samsung charger
Click to expand...
Click to collapse
I use my old 25W (original from N10+) charger and it takes about 1 hour to charge from 15-20% to full. I have the DevCheckPro app showing me at the start 17-18W and about 6-7Amps of charge load initially, at the beginning.
Hello!
I have been using RM8P for the past 2 weeks and everything was fine, the 65W EU adapter charged it really fast, however today I noticed something. I noticed that when I plug in the adapter to charge, the Maxcharge logo appears and the percentage displayer starts to rise fast, however after 1-2 seconds it slows down to normal charging speed, like if it was only a 20-30W adapter.
Why? How can I fix it? Restarting the phone did not help. I am on the latest OS for EU (3.19) .
Maxcharge logo is displayed but the speed drastically descreased ...
I checked several times while charging and I noticed that sometimes it speeds up and sometimes it slows down... why? Why is it fluctuating ?
What is the battery level when you plug in? My understanding of charging tech is that it is not always full speed from min to max. If you're sometimes plugging in above that throttle level it may go slower.
Then again, I'm not 100% on new charging tech. My RM8 has yet to arrive.
In my experience, it's not the phone but the charger. With my old op9pro it happened more than once, the charger started failing, you could get another 65w rated charger and check with accubattery the power delivered by both chargers. Down here they shipped the phone with the eu charger and a standard American charger rated "65” the eu Nubia charger goes to 64/ 65 watts without issues (I use an adapter to connect it) , the bundled one even though is rated 65 only gives 45w, sometimes 39, which is a bit annoying but it doesn't bother me, as long as I can charge it while having a shower or when I'm having breakfast before taking off, it does the trick, this thing is so good, battery lasts me 2 days