Hi.
I got a note 2 and would like to have an odin image with the official state as I bought it before I start tinkering with it (root, flashing rom, etc) so I can restore it if I need to claim warranty service.
The issue is: The firmware is of the austrian mobile operator 3 (www.drei.at) and I did not find an official firmware for it!
Can someone point me to it if it exists (did not find it on http://www.sammobile.com/firmware)?
Else: Is it possible to create an "official" system dump of it that works with odin? So if I restore from that created firmware it restores to the state I bought it without anything changed (no custom firmware counter increased, etc).?
I know there are some guides on how to create odin dumps, but they are rather complicated and I am unclear if I restore from one of those if it counts it as official (does it need to be signed for that and anyone not from samsung even do that?) and does not increase it.
Can you help me?
http://forum.xda-developers.com/showthread.php?t=1951091
You can root your phone and do whatever you want, and whenever you want. You can simply return to official warranty version by following steps in first reply of the link i attached.
Thanks
I don't think you get want I mean:
I know how rooting and flashing and odin works, i've done it lots of times. And i've also returned phones to stock.
Until now however I always had unlocked devices with completely official samsung firmwares, but now I have an oparator specific firmware: that of 3 austria.
I did not find an image for this firmware, so I cannot flash back the correct stock image because I did not find that specific image provided anywhere.
So my question:
- Where do I get the firmware JRO03C.N7100XXALIJ for 3 austria? Is it even available?
- If not: can I create it myself?
On http://www.sammobile.com/firmware the only option sensible that gives me results is the latest 10...
Is there a way to view all firmwares for a device (i.e.: n7100) to make sure mine is not among them?
this site is much better. you won't find that firmware exactly but you find other updates for your specific region!
http://samsung-updates.com/device/?id=GT-N7100
Hi there,
I have the Samsung Galaxy Tab S 8.4 LTE version, which I purchased through Ebay - I believe it came from Asia somewhere as it showed up with an international adapter for the power supply. It was sold as a "Verizon" model - I ditched that sim card and have been using it with Bell Mobility in Canada.
Recently, I tried to update my firmware using the latest version of Samsung Kies and I'm running Windows 10 latest version. For some reason Kies needs to reinstall the USB driver before performing the update to the firmware and this causes Windows 10 to crash without fail. (This is also happening to my Note 3 - Samsung informs me Kies is not compatible with Windows 10 although it seems to work for everything else - just not the update). Kies doesn't seem to care that I already have the latest drivers installed.
I can't update via the tablet because my device has been "modified" - rooted.
Finally I went to Sammobile for the firmware, however I can't find any US firmware for a compatible carrier under SM-T705. I am debating flashing the Bell Canada firmware, but the model is listed as SM-T705W. In case this is not ok and I need to revert to the original, I'm hoping someone can help me identify my build? The samsung agent offered to identify it but once she discovered it was from outside Canada she said she had no information. So much for Samsung International!
Please help! I'm having battery issues and I'm hoping updated firmware will help, plus I would like to have the latest version of Android. Thanks!
If you're in Canada then just flash the Canadian firmware.
ashyx said:
Cellular south is us
Region XAR
Click to expand...
Click to collapse
Hi there, forgive me for being thick, but how do you tell it's Cellular south, and what do you mean by region XAR? I'm sure that the fellow I bought this unit from flashed US firmware, however I can't find it on the Sammobile site - in fact I can't find any US carrier firmware listed for this model.
As mentioned above, I did find Bell mobility (Canada) firmware listed for the SM-T705W but nothing for the SM-T705.
Further explanation greatly appreciated!
LostinCanada said:
Hi there, forgive me for being thick, but how do you tell it's Cellular south, and what do you mean by region XAR? I'm sure that the fellow I bought this unit from flashed US firmware, however I can't find it on the Sammobile site - in fact I can't find any US carrier firmware listed for this model.
As mentioned above, I did find Bell mobility (Canada) firmware listed for the SM-T705W but nothing for the SM-T705.
Further explanation greatly appreciated!
Click to expand...
Click to collapse
You can flash any firmware for that model, so just flash the Canadian firmware, no point in flashing a us firmware.
ashyx said:
You can flash any firmware for that model, so just flash the Canadian firmware, no point in flashing a us firmware.
Click to expand...
Click to collapse
Ok great. I would like to locate the US firmware though for future use. I travel alot in the US and in the event I need a different carrier's modem... Are the US carriers listed somewhere else or am I blind? http://www.sammobile.com/firmwares/search/SM-T705/
Thanks!
LostinCanada said:
Ok great. I would like to locate the US firmware though for future use. I travel alot in the US and in the event I need a different carrier's modem... Are the US carriers listed somewhere else or am I blind? http://www.sammobile.com/firmwares/search/SM-T705/
Thanks!
Click to expand...
Click to collapse
You have root so install twrp from the development section and do a full back up of your current system.
You can then restore as you please.
Seems no US firmware for the t705.
ashyx said:
You have root so install twrp from the development section and do a full back up of your current system.
You can then restore as you please.
Seems no US firmware for the t705.
Click to expand...
Click to collapse
LOL... ok now I have another problem. I had already downloaded the Bell mobility file from Sammobile and hadn't seen this response - in the meantime I hooked up with Odin and my download failed twice - I don't get it. I just did my Note 3 10 minutes ago without any issues. Rebooted device and odin between both attempts.
Thoughts?
Don't flash anything until you make that full backup with TWRP, trust me it will save a massive headache should you need it.
Download Flashfire from the link below then set your date back to August, run Flashfire then load up the firmware, select the Flash firmware package option.
From the partitions list select system.img and boot.img only.
Under the reboot options select download mode then hit the flash button.
Once it has flashed and booted to download mode you will need to flash a lollipop bootloader (assuming you are flashing lollipop?)
You will find them in the bootloader thread.
After that just reboot the tablet, it will take about ten minutes for it to fully boot.
http://likewaphd.in/filewap-1-load/...2015/FlashFire_Pro_v0.21_-_Likewap.apk-0.html
Uh... ok you lost me early on. I downloaded the file - how do I install it? I remember using the TWRP thing several phones back when I was messing with custom ROMs. I had a problem with recovery and since then have never gone this route - I've been happy with stock rom and root - installed using Odin... sortof the KISS principle.
I can try TWRP, but could you dumb down the instructions a bit - as I mentioned, I'm a bit thick - particularly with some of the terminology! LOL
This is the file I downloaded - yes, Lollipop - I don't understand why I have the Odin Fail - google isn't helping me understand either. I have root, USB debugging is enabled and I followed the same steps as with my Note 3 - the message said write fail.
http://www.sammobile.com/firmwares/download/52301/T705WVLU2BOE4_T705WOYA2BOE4_BMC/ Is this what you mean by bootloader?
TWRP - flash with odin then boot into twrp using POWER + HOME + VOL UP - http://forum.xda-developers.com/gal...p-2-8-6-1-unofficial-sm-t800-805-807-t3074633
Bootloader - http://forum.xda-developers.com/showthread.php?t=3099362
ashyx said:
TWRP - flash with odin then boot into twrp using POWER + HOME + VOL UP - http://forum.xda-developers.com/gal...p-2-8-6-1-unofficial-sm-t800-805-807-t3074633
Bootloader - http://forum.xda-developers.com/showthread.php?t=3099362
Click to expand...
Click to collapse
Ok but those "bootloaders" are custom ROMS are they not? And I don't see my device on the TWRP site - I have the LTE version, it only shows Wifi.
Really all I want to install the Bell stock firmware (assuming it is indeed compatible - SM-T705 vs SM-T75W) I linked to from the Sammobile site and then do Chainfire's auto-root.
Why isn't Odin writing the firmware to my device? I've never had this issue before and I don't see what I might have done differently with this device - it's the first time I've tried to update it, but I had no trouble rooting it with the chainfire auto-root.
LostinCanada said:
Ok but those "bootloaders" are custom ROMS are they not? Really all I want to install the Bell stock firmware (assuming it is indeed compatible - SM-T705 vs SM-T75W) I linked to from the Sammobile site and then do Chainfire's auto-root.
Why isn't Odin writing the firmware to my device? I've never had this issue before and I don't see what I might have done differently with this device - it's the first time I've tried to update it.
Click to expand...
Click to collapse
No they are bootloaders they are required to boot the firmware , roms are the os.
Odin won't flash because certain devices will refuse to flash another regions firmware.
My advice to you is to flash the lollipop bootloader first, to make sure it will flash then flash the firmware with flashfire.
Obviously make the twrp backup first.
ashyx said:
No they are bootloaders they are required to boot the firmware , roms are the os.
Odin won't flash because certain devices will refuse to flash another regions firmware.
My advice to you is to flash the lollipop bootloader first, to make sure it will flash then flash the firmware with flashfire.
Obviously make the twrp backup first.
Click to expand...
Click to collapse
Ok I flashed the bootloader, and then I tried to flash the firmware with Odin again but it still won't do it - write fail again. I've never used flashfire - windows 10 won't open it...
UDATE: Ok I read to transfer the file to the download folder on the tablet, and then install on tablet. So I did that, but when I click on the icon it doesn't run. How the heck do I use this to install the firmware update?
Figured out the date bit, ran Flashfire.... problems during the install - got stuck in boot loop - tried a factory reset - that didn't work... stuck in loop. I think I'm bricked....
Left the default settings in place - very little in the way of instructions - read the bit about not trying to write over protected settings...
And got this:
You're not bricked as long as the tablet starts up and you can boot to Download mode.
I've seen that error with corrupt downloads so not sure why you're getting it.
Reboot to download mode. Just hold POWER + HOME + VOL DOWN until the device restarts and boots to download mode.
Doesn't matter if it's boot looping.
Reflash TWRP and restore the backup you made earlier. You will be back to where you started.
At this point I think the best option is to flash a custom lollipop rom.
There is a very good one I use on my t805 which is practically stock with a bit of bloatware removed.
Its in the development section called sweetrom.
At least one positive is that you were able to flash the lollipop bootloader, so upgrade is not impossible.
I'm definitely able to get to download mode - I was surprised that the factory recovery mode didn't work. I'm wondering if the file from sammobile is corrupted - I used the same file with Flashfire - now I think Odin was trying to save me. I'm downloading the same file again fresh, and it looks like Telus and possibly the other Canadian variants are the same - unless it's the same corrupted file.
I just hope the problem isn't because my phone identifies itself as a straight SM-T705. That is why I asked about that point earlier. There are plenty of straight 1705 options available - just don't know which country would be compatible - particularly for the modem.
I didn't understand how to use TWRP and I've had problems with it in the past (recovery) when I did figure out how to use it and was messing with custom ROMS a couple of years ago. I would really like to get myself back in order with a proper stock ROM and root. This tablet belongs in my car and right now I just want it to work properly - I'm using Torque to resolve some ongoing engine issues and it will suck if I have to go back to using the small screen on my Note 3.
If there is any way to figure out which of those countries for the 705 are compatible with Canadian carriers, in case this Bell firmware is defunct, that would be appreciated.
As well, is that bootloader going to cause any problems with stock firmware? I've already flashed it - does stock firmware come with bootloaders included?
OK before I go any further with this I need you to install twrp and make that back up. Twrp is now very stable.
Twrp will back up some very important partitions namely the Efs and modem. Don't take this warning lightly. The amount of people that have soft bricked their device because they didn't do this.
Boot into twrp then simply select the backup option and make sure the partitions on the left are ticked particularly boot,
Efs and modem.
Now as regards which firmware.
I would forget about installing the Canadian firmware.
It looks like this firmware will only install specifically on a Canadian device.
It doesn't really matter which firmware from which region you install as they are pretty much all the same except for the carrier ones which just add more bloat and some csc specific stuff.
Just go for an international rom. You've already flashed a bootloader from one of these roms so that proves you can flash.
Use odin to flash.
If you have connection issues afterwards then all you need do is restore your modem backup with TWRP.
That's why it's important you do this.
Follow these instructions and we will get you up and running.
Whole again!
Whole again!
For the record, I read elsewhere that it is NOT recommended to flash other letter variants of a model. In the meantime I downloaded all four Sammobile Canadian Carrier files and they appear to be the exact same file and all install attempts failed For anyone else with an actual SM-705W I read in this thread: http://forum.xda-developers.com/galaxy-tab-s/general/t705-lollipop-t3099945 a fellow Canadian was having a problem with those same files. Dunno what happened with him in the end, however I tried one more W file I found elsewhere that appeared to be different but it failed as well.
Based on the comments in the above thread, I flashed the Hong Kong variant for the SM-705 from Sammobile - apparently it was the first firmware widely available and users from several countries posted they had used it successfully. So far it seems to be working ok - after flashing it, I did a factory reset on the device as was also recommended in the above thread. Sure hope the battery life will be better than before - love this tablet but I've never seen a device drain so rapidly! CF-Auto Root restored!
As a side note my Ebay seller did reply to my origins query and was helpful once he realized I wasn't complaining about the device and wanting to return it... LOL. Apparently my unit originated in Singapore and arrived with that firmware along with a Verizon SIM which I never tested. As long as the OS is smooth, and the modem compatible, and unless someone advises a better country variant, I guess I'll stick with this one.
Now just need to get Torque reconfigured!
I am using a rooted Galaxy S9+ running the latest version of LightROM.
I recently discovered that Android 10 beta is out but since I am on a custom ROM, I have decided that I want to revert back to stock and then use Samsung Members in order to obtain the update. From what I understood, I needed to flash a firmware that is eligible for the beta update, which is why I downloaded the latest UK firmware from SamMobile (G965FXXU7CSK1_G965FOVF7CSK1_VOD).
I would like to know how things will work before I proceed. These are the steps from my understanding:
1) Backup everything so I can format the device
2) Flash the firmware mentioned above using ODIN
3) After the installation is complete, run Samsung Members in order to obtain the update or use one of the OTA zip files floating around (for S9+ Exynos)
4) After the update is complete, flash TWRP and root using this guide
Am I missing something or is that the entire process? My phone's model number is SM-G965FZKGEGY and it is an unlocked variant of the Exynos Galaxy S9+ (dual-sim). Would my phone have to be from a specific region (CSC or w.e) or should the process above work fine? And lastly, is Spotify still broken on Android 10 or was it fixed with an update?
Thanks a lot for your time.
Hi Guys,
About a month ago I got new Galaxy S9 with firmware G960FXXSBETH2,
As it turned out it has all kind of reception issues, so I tried to find alternate ROM for it to see if this issue can be improved.
While searching for ROM at Sammobile.com I noticed that the latest version for my region is different than the one I have on my device, and in fact I should have firmware G960FXXUAETG3.
I got ODIN (3.14.4) but when tried to flash the alternate firmware got this message:
"sw rev check fail bootloader device 11 binary 10"
So as it seems this device came with high boot-loader version 11 and I understand that I can not downgrade it either way - correct me if I'm wrong on this.
So what are my options on this?
Is there an alternate ROM that I could use? Maybe a customized one?
Or am I'm stuck with this firmware,
Many thanks
Hi All,
I've got a Note 10+ 5G and was wondering how would one go about rooting this device on the latest Samsung firmware
N976BXXU6FUBDThe guides that I have seen such as Dr.Ketans thread, instruct to flash a boot loader image that on his media fire page. does not match the firmware I'm running.
As I wouldn't want to flash anything that would break the phone, I'm wondering if someone can give me a method on how to root the stock rom.
thanks
did you find a solution? I manage to root the same model as yours tricking the lz4 files which is the new type of extension in Android and for this you can not root in a normal way. I followed this guide
Fix Oreo Firmware Installation Issue in Odin for Samsung Devices - DroidViews
Android Oreo has finally made its way to Samsung's latest S series flagships, the Galaxy S8 and S8+. The Oreo update brings with it the usual Android Oreo features such as Picture-in-Picture, redesigned Settings app, etc. It also brings with it Samsung Experience 9.0 which is but a fancier name…
www.droidviews.com
After having the 4 stock files modified without lz4 you must flash them with Odin.
After you take the modified AP file and patch it with Magisk.
Then you flash again stock using the patched AP file and the rest of modified files but you must not select autoreboot in Odin. When the flashing is done you must exit download mode and imediatelly enter in Recovery mod but better use this guide
How to Root Samsung Galaxy Note 10 and Note 10+
In this tutorial, we will show you how to unlock the bootloader and then root Samsung Galaxy Note 10/Note 10+ using Magisk. This guide supports Exynos variants of the Galaxy Note 10 and Note 10+ with…
www.thecustomdroid.com
This methods do not work for me now. I am in the latest R update 07 and it seems dont work. I am serching how to root my phone now...
SiqrCarnbon said:
Hi All,
I've got a Note 10+ 5G and was wondering how would one go about rooting this device on the latest Samsung firmware
N976BXXU6FUBDThe guides that I have seen such as Dr.Ketans thread, instruct to flash a boot loader image that on his media fire page. does not match the firmware I'm running.
As I wouldn't want to flash anything that would break the phone, I'm wondering if someone can give me a method on how to root the stock rom.
thanks
Click to expand...
Click to collapse
Hi, I am in exactly the same boat, did you solve it and get your sm-n976b rooted and if so how, Please and thanks/