Hi, I am having an issue with my Asus Zenfone 2. The title says it, it's pretty normal, but at the same time it's not normal. I have been trying to flash a recovery in fastboot mode, but I can't. Once I get to the fastboot screen, it starts counting down seconds from 5, and it won't let me flash/send the file successfully, and my phone simply turns off and turns on normally, a normal reboot.
The only problem is that, it doesn't stay in fastboot mode, it restarts in 5 seconds after you get to the fastboot menu.
Does anyone know what can I do to fix that? I have no clue why it does that.
Thanks
Anyone? :/
When I boot up my watch I get this message: device software cannot be checked for corruption.
I cannot boot into fastboot Mode because of this message. Anybody know how to get rid of it or how to bypass it so I can use fastboot? Would very much like to try the new preview of 2.0....
use ADB to reboot into fastboot mode
"adb reboot bootloader"
nkolsen said:
When I boot up my watch I get this message: device software cannot be checked for corruption.
I cannot boot into fastboot Mode because of this message. Anybody know how to get rid of it or how to bypass it so I can use fastboot? Would very much like to try the new preview of 2.0....
Click to expand...
Click to collapse
I get the message, but the "hold button mode" works for me, I just keep it pushed past that message and it vibrates, quick release and press and I'm in bootloader mode. :good:
Also the adb command works too, as noted above.
Thank you so much ?? Feeling a bit stupid now ?
No luck
Pkt_Lnt said:
I get the message, but the "hold button mode" works for me, I just keep it pushed past that message and it vibrates, quick release and press and I'm in bootloader mode. :good:
Also the adb command works too, as noted above.
Click to expand...
Click to collapse
I am having the same issue. Having the button pressed past the message and release after it vibrates, it comes back the Huawei Logo on my watch. I didn't seem to go on bootloader mode.
I am stuck with bootloader. Couldn't not enter recovery. Flashing from bootloader again and again didn't work. Couldnt enter download mode either. It goes into download mode then starts restarting. Tried RUU, it says low battery. When tried power off it and put to charge, charging icon comes and then restarts again and again.
N.B. DDR test looping, message on fastboot screen
itsmelutfor said:
I am stuck with bootloader. Couldn't not enter recovery. Flashing from bootloader again and again didn't work. Couldnt enter download mode either. It goes into download mode then starts restarting. Tried RUU, it says low battery. When tried power off it and put to charge, charging icon comes and then restarts again and again.
N.B. DDR test looping, message on fastboot screen
Click to expand...
Click to collapse
I think you are the 4th or 5th member whom has posted about this issue. I don't think any of them came to any solutions, but search for the threads, I haven't been keeping up. Sorry to hear this and hope you get it resolved.
Hey everyone,
A2 lite phone is in bootloop - allegedly (not my phone) "out of nowhere". The user does not do any fancy things like flashing, and this has not been done either.
Phone is on continuous boot loop, and sometimes (really seems randomly), the device starts up in the "no command" mode and stays there for a while. I read that we could go into fastboot mode by pressing "power button and tapping volume up key", but this doesn't do anything.
I've tried this thread: https://www.the***********.com/boot-xiaomi-mi-a2-fastboot-mode-recovery-mode/
But I'm not even getting into fastboot.
I'm almost thinking that the volume buttons are just broken, though from the feedback of the buttons this doesn't seem realistic.
EDIT: ok, now I'm somehow able to get it into fastboot.... sometimes. Now I'm here:
I switched the partition from a to b, but it still goes into bootloop. Then I switched it back to a, still bootloop. Then back to b. Still bootloop! But at least now sometimes I'm able to get into fastboot. No matter what kind of commands I'm typing in the cmd console, after about 10 seconds on the fastboot screen, the phone just reboots.
idk, it looks almost as if both partitions have the bad android 10...
Do you guys have any idea? Please let me know if more info is helpful.
You go into fastboot mode by holding Vol Down + Power button. So try holding Vol Down and Power button at the same time to go into fastboot mode. (Don't tap it)
Go here and grab the image you prefer (latest should do the trick) : https://forum.xda-developers.com/mi-a2-lite/how-to/fastboot-xiaomi-mi-a2-fastboot-images-t3824871
Then go ahead and follow this guide here to flash the stock ROM : https://c.mi.com/oc/miuidownload/detail?guide=2
This will wipe the data on the device, but it seems like you have no other option at this point. Cheers.
Thanks! I've tried that now. It starts flashing the device until... after about 10 seconds, the phone reboots from Fastboot mode .
As per this page: https://twrp.me/xiaomi/xiaomimia2lite.html
I've tried to do a recovery via TWRP. If I execute `fastboot boot path/to/twrp.img` then I go from fastboot to TWRP (the teamwin logo), but right after that the phone already reboots.
https://www.xda-developers.com/how-to-install-twrp/ - I don't know if it means anything, but when I execute `adb reboot bootloader`, the console returns `error: no devices/emulators found. If I execute `adb devices`, it does not list my device. However, if I execute `fastboot devices`, my device is listed.
I installed ADB usb drivers, so when I get my phone connected in fastboot, it shows up as Android Bootloader Interfacee in device manager. So not sure what's going on here, but it's all weird.
What I'm facing is very, very similar to https://www.reddit.com/r/Xiaomi/comments/4ltzt9/xiaomi_mi_note_boot_loop_even_in_fastboot/ <-- but that thread is a bit of a dead end (and 3 y/o)...
daize said:
after about 10 seconds, the phone reboots from Fastboot mode .
Click to expand...
Click to collapse
Hmm, it should never do that, maybe it's a hardware issue that we can not fix via Fastboot ?
daize said:
As per this page: https://twrp.me/xiaomi/xiaomimia2lite.html
when I execute `adb reboot bootloader`, the console returns `error: no devices/emulators found. If I execute `adb devices`, it does not list my device. However, if I execute `fastboot devices`, my device is listed.
Click to expand...
Click to collapse
When the device is in Fastboot mode, it will only be recognized as Fastboot. Only when it's properly booted, the device can be recognized in ADB, so no issues there.
I assume your bootloader is already unlocked as you have successfully booted into TWRP. You might try EDL (Emergency Download Mode) flash as a last resort :
Download MiFlash (20160401) from here : https://www.xiaomiflash.com/download/
You're downloading that particular version because it is able to EDL flash on your phone. Install the MiFlash you've downloaded and open it, then put the phone into fastboot mode. Connect it to your PC and use this code to take the phone into EDL mode:
Code:
fastboot oem edl
After you hit enter, you will see the screen turn off and notification LED blinking, this is normal. This means the phone is in EDL mode. Open the MiFlash you've installed (likely in C:\Program Files\Xiaomi\MiPhone) and browse to the ROM location and connect the phone. Choose "Flash All" and start flashing.
After the EDL flash is complete the phone will not reboot. It will stay in EDL mode. You need to disconnect the phone from PC and hold power button (about 10-15 seconds) to boot the phone. If the phone boots properly, you can go into fastboot and connect it to PC, then use:
Code:
fastboot oem lock
to relock your bootloader. Try it and let me know. :fingers-crossed:
Thanks for the continued help!
I've followed your steps - When I run fastboot oem edl, the console returns "... okay [ 0.0202s] finished. total time: 0.022s" and the phone turns to a black screen (no notification led blinking). Then... after a couple of seconds, goes back into the boot loop .
Something maybe to note: every time that my phone starts up, it (1) shows a screen saying "Your device software can'tbe checked for corruption.Please lock the bootloader.", and then slides down to the typical "androidone" white screen before it reboots again.
daize said:
every time that my phone starts up, it (1) shows a screen saying "Your device software can'tbe checked for corruption.Please lock the bootloader.", and then slides down to the typical "androidone" white screen before it reboots again.
Click to expand...
Click to collapse
The screen with the ugly text is normal, since you have an unlocked bootloader, it's there to warn you that the device's software might've been tampered with. On the main subject though, I'm out of ideas. You might try booting the phone by holding Power + Vol Up, which should normally boot into stock recovery or wipe the data on the device. But I'm slowly beginning to think that this might be a hardware issue rather than a software issue that I can help you to fix.
Under normal circumstances, EDL flash is the way to fix any problems you might encounter with the software, that's why it's called the Emergency Download mode. But since we're past that stage, I believe I will not be able to assist you further. Hope you can fix your device my dude/dudette!
If the phone gets out of fastboot mode your phone does not get recognized from your computer. Try to delete fastboot and minimal adb and download the latest version. [https://forum.xda-developers.com/android/general/tool-adb-fastboot-installer-tool-windows-t3999445]
Open MiFlash, click Driver left on the top and install them.
Set path to the downloaded firmware. Now boot into fastboot, once that is done connect your USB cable to both, computer and phone. If this doesn't work try different USB-Ports and USB-cables. Some work, some don't. This might be the reason for leaving the fastboot mode.
Click refresh and see if your device appears
@marstonpear thanks for your help so far <3 @Cappucinto, thanks for chiming in! What do you mean with this: "Open MiFlash, click Driver left on the top and install them." <-- in MiFlash, I do not see an option to select driver...
@marstonpear thanks for your help so far <3
@Cappucinto, thanks for chiming in! What do you mean with this: "Open MiFlash, click Driver left on the top and install them." <-- in MiFlash, I do not see an option to select driver...
What did change now after installing these drivers: https://forum.xda-developers.com/android/general/tool-adb-fastboot-installer-tool-windows-t3999445]
I did try some other USB cables. The one I've been trying triggers the windows sound for "new device successfully connected" when I boot the phone up in fastboot, and then of course gives the "device disconnected" sound when the phone then reboots. With another USB cable in this case, windows just states: "USB device not recognized". So it seems like the cable I haven't been using is defect .
I'm unable to use MiFlash at the moment so I can't explain the whole procedure with installing the drivers in MiFlash. But there has to be something like "Install > Drivers" or something. Maybe someone else can help out.
Try to use the working cable again, open a command prompt and type: fastboot devices
Then wait for an answer, post it here and see if the phone reboots again or if it stays in fastboot
daize said:
Hey everyone,
A2 lite phone is in bootloop - allegedly (not my phone) "out of nowhere". The user does not do any fancy things like flashing, and this has not been done either.
Click to expand...
Click to collapse
The response by marstonpear below makes sense.
marstonpear said:
You go into fastboot mode by holding Vol Down + Power button. So try holding Vol Down and Power button at the same time to go into fastboot mode. (Don't tap it)
Click to expand...
Click to collapse
Although u shd consider this link, i tried to arrange it step by step:
https://forum.xda-developers.com/sho...php?p=79365091
Follow the instructions, as dat was how i revived mine. Hopefully it may help u.
Note; wen using twrp, preferably use " twrp - offain "
Miflash tool:
Link 1: https://www.xiaomiflash.com/download/
Preferably use Link 1 & choose either 2016, 2017 or 2018 versions. They come preloaded with the drivers u need
Link2: https://xiaomibuzz.com/downloads/download-xiaomi-mi-firmware-flash-tool-latest-version-2018.html
Lets know how it goes
Cappucinto said:
I'm unable to use MiFlash at the moment so I can't explain the whole procedure with installing the drivers in MiFlash. But there has to be something like "Install > Drivers" or something. Maybe someone else can help out.
Try to use the working cable again, open a command prompt and type: fastboot devices
Then wait for an answer, post it here and see if the phone reboots again or if it stays in fastboot
Click to expand...
Click to collapse
Hey there When I get into fastboot and run `fastboot devices`, a code returns <tab> fastboot.
... and then the phone restarts I'm trying but I guess I'm beyond the stage of being upset, haha.
@agbadino https://forum.xda-developers.com/sho...php?p=79365091 <-- that first link seems to be broken, could you check again? I'd love to try your steps!
daize said:
@agbadino https://forum.xda-developers.com/sho...php?p=79365091 <-- that first link seems to be broken, could you check again? I'd love to try your steps!
Click to expand...
Click to collapse
Sorry bout d previous link. I believe this shd take u directly to the tutorial:
https://forum.xda-developers.com/mi...tboot-mode-t3920925/post79365091#post79365091
remember to use "twrp offain for daisy". It works better than the regular twrp for daisy
It my take and procedure that worked for me at the time. Good luck tho
Thanks! Sadly, when I get to the `fastboot oem edl` step, it fails. I get into fastboot, I quickly enter `fastboot oem edl`. CMD says finished, the screen turns off. I immediately refresh in MiFlash (COM3 is the device), I start flashing. After 4 seconds, the device turns off (windows sound "device disconnected"). The flashing runs for a total of 7-9s says "the operation completed successfully.(0x000000000: cmd <?xml version="1.0" ?><data .. etc etc
So I don't really know what to do if I can't get into EDL mode .
daize said:
Thanks! Sadly, when I get to the `fastboot oem edl` step, it fails. I get into fastboot, I quickly enter `fastboot oem edl`. CMD says finished, the screen turns off. I immediately refresh in MiFlash (COM3 is the device), I start flashing. After 4 seconds, the device turns off (windows sound "device disconnected"). The flashing runs for a total of 7-9s says "the operation completed successfully.(0x000000000: cmd <?xml version="1.0" ?><data .. etc etc
So I don't really know what to do if I can't get into EDL mode .
Click to expand...
Click to collapse
Try getting another chord and try again.
Tried some other cables. Every time I run fastboot oem edl, it keeps saying "finished", and then reboots the phone in about 5 seconds. One time, it said "Catastrophic failure" as "status" for the flashing.
Otherwise, it most often says "The operation completed successfully.(0x00000000: cmd <?xml version="1.0"?><data><patch SECTOR_SIZE_IN_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size_in_bytes="4" start_sector="NUM_DISC_SECTORS-1." value="CRC32(NM_DISK_SECTORS-1.,92)" what="Update"/></data>)
But then still continues in the bootloop...
Hi, recently i got in a bootloop. I was at the beach, taking pictures with Gcam, and suddenly the phone started locking and unlocking the screen, and after some time it rebooted with a "android" screen. It showed a warning saying my android was corrupted, and gave me the option to try again or factory reset.
I clicked "Try Again" and the phone tryed to reboot, and it is in a boot loop since then. I can start it in fastboot mode, but the device won't be seen by Rescue and Smart Assistant, or by ADB. Yes, i have the USB drivers installed. When i try to enter recovery mode it says "no command", and factory mode just starts the bootloop again. Please someone help me
Managed to get past no command screen, and dida factory reset.