Related
any tips or tricks to putting the screen protectors on without getting bubbles or dust and lint sticking to adhesive side of protector?
If and when you place your screen protector and notice a finger print or lint, you can repair it. I use clear packing tape, cutting two strips about 1/2" wide. Place one on the top near (but not over) the area you are working with. This is used to lift the protector so you can get under it to where the problem is. Then slip the second strip under the protector, facing up or down depending if the problem it on the protector or the glass. I do it one way then the other for good measure. Once the tape is in place, lower the protector, press on the area, raise the protector, remove the piece of tape under the protector, then lower the protector to see if the blemish is gone.
Repeat where needed. Remove the piece of tape on the top by holding the protector beside the tape, and pulling the tape off the top.
This will remove fingerprints underneath the protector whether it is on the protector or the glass. It will also remove dust, fibers, etc.
It is entirely possible to place the screen protector where it is straight and without anything caught underneath, but I have used this method many times.
If you would like to see the process, search Youtube for "removing lint from under screen protectors".
I'm lazy -- I took mine to BestBuy and had them do it. It cost around $12, but they did the job right. I always seem to screw up when putting them on myself.
there is no need to "protect" the screen
http://www.youtube.com/watch?v=ivxlsNLi-9s
only good if protector is fingerprint resistant
danij3l said:
there is no need to "protect" the screen
http://www.youtube.com/watch?v=ivxlsNLi-9s
only good if protector is fingerprint resistant
Click to expand...
Click to collapse
I agree, it makes no sense to use a screen protector on something that has Gorilla Glass like the KF does, other than fingerprints or possibly a privacy screen protector.
I purchased the Skinomi from Amazon. It did not really help with fingerprints like I had planned, nor did it look very good on the screen - contrary to the Skinomi I have on my iPhone 4...
My fire got a light scratch on it in about a week. Never dropped, lived in its case, babied.
Get a screen protector.
(I am anal and hate even the smallest defect. It was indeed a small scratch only noticeable in certain light, but was a scratch.)
brett10 said:
I agree, it makes no sense to use a screen protector on something that has Gorilla Glass like the KF does, other than fingerprints or possibly a privacy screen protector.
Click to expand...
Click to collapse
I disagree. I have Gorilla Glass on my Samsung Epic 4g which survived the same type of 'demonstrations' showed in that video. Not wanting to impact the beauty of the screen (touted as one of its primary features when the phone came out), I left mine unprotected. However, after less than a year of use, there are still a significant number of scratches on it, and even one 'chunk' missing that is visible from all angles.
Came here to see if anyone recommended a specific brand over another. While the anti-glare screens sound nice, I have also read that it impacts viewing in a negative way - sounds like something I don't want for a device designed for reading. Therefore I figured I'd stick with a clear protector, but was looking for reviews.
I've always loved and used the SGP Steinheil Ultra Crystal.
[I'll add link later]
The anti-fingerprint ones they sell are junk. They really muck up the screen. But the ultra-crystals are great and provide another layer of protection. I haven't installed mine on my Fire yet, but I will once I get around to it.
Though Gorilla Glass is amazing stuff, it is not scratch-proof. I'll continue using screen protectors regardless of what type of glass.
Interesting. I have a 2 year old Incredible with a perfect screen and never used a screen protector. I must be the most careful person on earth.
.46caliber said:
The anti-fingerprint ones they sell are junk. They really muck up the screen.
Click to expand...
Click to collapse
Agree and disagree. While it does hinder the quality a tiny tiny bit, I personally love the feel of the matte surface while reading a book. That, combined with anti-glare, make the clear protectors utterly useless to me. If I'm reading / watching anything, I certainly don't want to have to tilt the device to get rid of glare to see the screen clearly.
I bought the Acase matte screen protectors and absolutely recommend them to anyone. 3 pack for $12.99 shipped on Amazon. (Girlfriend loves them too)
I have an XO Skin on my Nexus and love the look of it. You really can barely tell its there and it helps a ton with the finger prints. They make one for the Fire as well: http://xoskins.com/amazon-kindle-fire-screen-protector
Be aware that this is a wet applied protector. I find the best way to apply them is the steam up the bathroom really well for a few minutes, then turn the water off for a few minutes to let any dust in the room settle. Then do a really good wipe down of the screen with a non lint towel and blow it completely clean with compressed air.
When applying the protector, use a lot of the application liquid, on the protector and your fingers.
I just installed a Skinomi protector. Still waiting for it to dry and all, but as far as I can see I removed pretty much all of the bubbles. It was around 9 bucks shipped, came well packaged with clear instructions and a lifetime warranty. As long as it the picture quality isn't disturbed, I think it's going to be a winner.
I do want to try one of those matte protectors now though...
After dealing with cheap screen protectors I ordered a couple different well reviewed protectors.
I got the armorsuit militaryshield.
It installed great, but had to apply it wet (which i don't like) and let sit for 12 hours.
It turned out very nice, you really couldn't tell it was there besides very minor screen distortion. I really didn't like how it felt, a little sticky.
I had to rma that kindle and couldn't save the shield.
So I got a greatshield ezseal
If you're looking for a protector this is the one to get.
Best protector Ive ever used.
Its basically just like the moshi ivisor for ipad.
It doesn't stick to the screen, the adhesive is on the outer edges and it basically lies on the screen -so no bubbles. you can even take it off and wash it.
I tried the Acase matte screen protectors on Amazon and they looked awful. They mute the color palette and give everything a fuzzy look. Tried the Acase clear screen protectors instead and they worked out fine. Can't see the fingerprints and the screen still looks good.
yeah matte will make it a bit fuzzy/greasy looking
the ezshield is matte
Got this:
http://www.amazon.com/gp/product/B000ALDUFG/ref=oh_o00_s00_i00_details
BoxWave Amazon Kindle Fire ClearTouch Anti-Glare Screen Protector
I really like how it fits, it really make the display look better.
Don't really care about scratches, but the reflections on the KF can be pretty annoying outside.
It's not really anti-Fingerprint but it's way more easy to clean.
It's also reusable.
I thk a screen protector is ideal if your banging it around or throwing stuff of it but other than theres no reason to really.
ive only had i protector on 1 one the phones ive had, all the rest of the stuff I dont have any SP on them.
I have never had any prob with the screen getting scratched.
---------- Post added at 02:20 PM ---------- Previous post was at 02:18 PM ----------
If I could find something that would let me see the screen in the sun now that would be worth it. LOL
Is it making the screen use better outside then? And what about the use inside?
Sent from my MIUI.us Sensation 4G using XDA App
I'd definitely speak against screen protectors; I purchased a highly rated myGear one with my Fire and noticed that though fingerprints didn't seem to appear as easily, they were almost impossible to wipe off completely. It also noticeably detracts from what is such a good screen.
I'm just curious if anyone has removed it and it is better with no issues. I didn't get the extra one in the box and the one on there already has a hairline scratch that is annoying me, I've never had a screen protector on any smartphone before....
i have removed it and no the sony logo doesnt peel off like on the z, i have applied IQ screen protector and it is way better int terms of scratches and fingerprint smudges.
sirsmokey said:
i have removed it and no the sony logo doesnt peel off like on the z, i have applied IQ screen protector and it is way better int terms of scratches and fingerprint smudges.
Click to expand...
Click to collapse
Thanks, I'll check into that screen protector. I was curious too if anyone has left it off (without another one) and had any issues - I've read some people saying it has no oleophobic coating so gets a lot of fingerprints. And so I read about a product called Fusso Smartphone http://www.amazon.com/Anti-fingerprint-Oleophobic-SmartPhone-TM-necessary/dp/B008HVBU9O and am thinking maybe this can be used? Or is it good by itself after removing screen protector
I would only suggest that u use a screen protector made specifically for your phone brand and model type.
Should you get a protector ? only you can decide what kind of person you are and how to treat things you purchase.
but in my instance
I took my OEM screen protector off a day earlier than when the new one was to arrive. that was a long day, constantly had to remind my self to be careful of where I put my phone. I am quite pleased with IQ s screen protector
sirsmokey said:
i have removed it and no the sony logo doesnt peel off like on the z, i have applied IQ screen protector and it is way better int terms of scratches and fingerprint smudges.
Click to expand...
Click to collapse
it mean sony logo still there even i remove the screen protector ?
yes it is still there. on the xperia z it does come off
keith777 said:
I'm just curious if anyone has removed it and it is better with no issues. I didn't get the extra one in the box and the one on there already has a hairline scratch that is annoying me, I've never had a screen protector on any smartphone before....
Click to expand...
Click to collapse
The screen film that comes stock on the Xperia ZL (as well as the Z) is not a screen protector...it is a film (protector) to help keep the glass from shattering. I have heard and seen the video where the kid decides to remove this level of protection. Why? Because he is crazy. I purchased the Skinomi Tech Skin screen protector (wet application) and installed it right over the stock film and it works beautifully. No degradation of the HD screen quality nor sensitivity of touch. Now, I have both a screen protector on top of the film to protect the screen from shattering as originally shipped from Sony.
I am not sure of the tempered nature of the Sony screens. Definitely not Gorilla Glass 1 or 2 but, I have heard it is from an Asian company that makes similar screens to Gorilla Glass (I thing it is called Dragontrail). I guess you could argue if the screen on the ZL was of the Gorilla Glass quality or better, the point would be mute, and no screen or shatter film protection would be necessary.
Good quality screen protector is a small investment to protect such a beautiful phone.
jmarnell said:
The screen film that comes stock on the Xperia ZL (as well as the Z) is not a screen protector...it is a film (protector) to help keep the glass from shattering. I have heard and seen the video where the kid decides to remove this level of protection. Why? Because he is crazy. I purchased the Skinomi Tech Skin screen protector (wet application) and installed it right over the stock film and it works beautifully. No degradation of the HD screen quality nor sensitivity of touch. Now, I have both a screen protector on top of the film to protect the screen from shattering as originally shipped from Sony.
Click to expand...
Click to collapse
Sorry, but you are incorrect. It is a screen protector. In Japan, it is really common practice to sell phones with factory/service installed screen protector, because it saves person from trouble of trying to apply protector without dust getting under it, also adhesive could be used for more robust installation. So when somebody scratches theirs, they just pop in the service to get protector replaced instead of replacing whole screen - it saves company & user lot of costs.
This film protects glass from shattering to extent, but no more than any screen protector does. Its pointless to install second protector on top of it, this will only reduce backlight brightness & sensitivity (even if slightly).
Whatever it is, it sucks. I've never had a screen protector before, the glass feels way better to me, and probably looks a little better. The thing that comes on here scratches so easy - all I ever do it set it down screen up or put it in my pocket with nothing else in that pocket. Not to mention the lint it attracts..
I ordered the Fusso smartphone stuff for applying an oleophobic coating, seems to have gotten mostly good reviews, when I get it i'm removing this screen protector. I'll post results when i'm done..
So I removed the screen protector, wasn't hard at all just had to use a pin to get it started. To me, the glass feels way better and looks better. I applied the Fusso smartphone for adding an oleophobic coating last night. So far so good, after being on the phone a little bit this morning I saw some fingerprints and just used my shirt to wipe them off and they came right off - I guess the oleophobic coating is working, although it didn't seem bad even before I put it on the glass. Sony should really abandon the practice of putting a screen protector on new phones ( i don't think anyone else does), maybe include it, but this feels way better to me without it.
keith777 said:
So I removed the screen protector, wasn't hard at all just had to use a pin to get it started. To me, the glass feels way better and looks better. I applied the Fusso smartphone for adding an oleophobic coating last night. So far so good, after being on the phone a little bit this morning I saw some fingerprints and just used my shirt to wipe them off and they came right off - I guess the oleophobic coating is working, although it didn't seem bad even before I put it on the glass. Sony should really abandon the practice of putting a screen protector on new phones ( i don't think anyone else does), maybe include it, but this feels way better to me without it.
Click to expand...
Click to collapse
So... Sony logo really doesn't come off with the screen protector right? Good to know.
A question: Is the screen really scratch resistant? Searched for some videos and didn't find any screen scratch test, etc. I know you're not going to scratch your screen just to test it, but, do you leave it with keys, coins...? Would be glad to know if gets scratched easily or not. And when you take off the screen protector, is there any hard to remove glue on the screen?
WendellGnR said:
So... Sony logo really doesn't come off with the screen protector right? Good to know.
A question: Is the screen really scratch resistant? Searched for some videos and didn't find any screen scratch test, etc. I know you're not going to scratch your screen just to test it, but, do you leave it with keys, coins...? Would be glad to know if gets scratched easily or not. And when you take off the screen protector, is there any hard to remove glue on the screen?
Click to expand...
Click to collapse
What do you mean by "really scratch resistant"? Do you mean scratch-proof? Because its not, and there is no such thing as scratch-proof material. If you find something harder than glass, you can scratch it. Ordinary sand is the best example.
If you carry phone in pocket with keys (or in jeans pocket with studs which could contact screen when you move it from/to pocket), I recommend using screen protector.
To remove tackiness which could be left from original one, just use some alcohol to clean it.
...my naked N5 slipped from my cold, numb fingers and landed flat but face down on a NYC sidewalk a couple days ago. At first it looked like a "soft landing" but no such luck and now I'm looking at a screen replacement (screen itself OK, but glass cracked all to hell).
So now I'm wondering if this could have been prevented simply by a case and not necessarily a screen protector as well. I've used cases such as an Otterbox Commuter in the past but never dropped any of those phones to the extent this one went down. It seems to me that any case with a slight lip on the front -- as most of them must have -- would be enough since the screen itself would not hit the ground.
From research on this forum and web sites I'm currently favoring the Spigen Thin Armor case but am wondering if a high-quality screen protector would also be worth it. My screen at the time it was damaged really had no scratches at all, so the Gorilla Glass was doing its job. Would one of those tempered glass protectors also provide shatter protection? Or would a decent case by itself be sufficient?
FWIW, I've used thin-film protectors in the past but always found them annoying due to bubbles, making the screen less readable, and/or affecting the touch response.
Even with a case on, if there was a small rock or a jagged edge on the ground that nicks the screen, it would have still been toast anyway. This is regardless of if there was a lip protecting it or not. It all depends on what's on the ground by chance.
A tempered glass protector probably could have saved the screen though, since you said it landed flat on its face. Tempered glass protectors are perfect for impacts that land face down, not so much on edges or sides. You will see most demonstrations of tempered glass done with nails, hammers, drop tests, etc. with the phone being impacted directly on the face. If it impacts from the side, there is a good chance the screen could still break as tempered glass isn't really designed to protect from those types of impacts.
That is where the case with a lip comes in. Those are meant to protect from side and edge impacts. Most drops generally don't land flat like yours, they tend to bounce around on corners first, so the case would absorb most of the impact and not the phone directly.
Your best bet is to both have a tempered glass screen protector (for flat impacts), and a bumper frame or TPU case (for the rest).
I use a Nillkin H+ Tempered Glass screen protector and a bumper frame (back not covered as I put a skin on the back) and I'm pretty much covered for most brain lapse moments.
rochrunner said:
FWIW, I've used thin-film protectors in the past but always found them annoying due to bubbles, making the screen less readable, and/or affecting the touch response.
Click to expand...
Click to collapse
Once you learn the hinge method for putting on screen protectors, you won't have air bubbles or dust underneath. You can't even tell my phone has a screen protector on it. Youtube has several videos on how to do it properly.
I refuse to pay big $$$ for glass protectors because you only get one of them, and you either do it right, or throw it away. With plastic protectors, you get several for a few dollars.
wolfen69 said:
I refuse to pay big $$$ for glass protectors because you only get one of them, and you either do it right, or throw it away. With plastic protectors, you get several for a few dollars.
Click to expand...
Click to collapse
That's not true. I applied and removed my Nillkin more then 10 times during the application to get rid of the dust I missed trapped underneath because I suck at applying screen protectors. It reapplied the same every time. All you have to do is make sure you don't firmly press it down and you're fine. This is even after you see the adhesion process occur. It will still peel up. The adhesive takes a few hours to a day (depending on brand) to fully stick/cure.
If a person like me can apply one glass screen protector, anyone else will do it better. One is all you need.
Plastic will only give basic scratch protection and leave a greasy screen after a while. If it takes the same fall his did, the screen would still be done for.
mmmmBACON said:
I use a Nillkin H+ Tempered Glass screen protector and a bumper frame (back not covered as I put a skin on the back) and I'm pretty much covered for most brain lapse moments.
Click to expand...
Click to collapse
What bumper frame do you use? I've been looking for one myself for a while now...
Cases protect the actual body of the phone, and maybe the screen if it happens to land flat. But if a rock of some other elevated object hits the screen then it will be done for. And a plastic screen protector will do nothing, that protects against scratches like from sand. A glass one would be the best bet for shatter protection. I've seen a person take a hammer to a screen with a glass screen protector on. The protector was rekt but the phone screen was fine.
Awesomepie85 said:
What bumper frame do you use? I've been looking for one myself for a while now...
Cases protect the actual body of the phone, and maybe the screen if it happens to land flat. But if a rock of some other elevated object hits the screen then it will be done for. And a plastic screen protector will do nothing, that protects against scratches like from sand. A glass one would be the best bet for shatter protection. I've seen a person take a hammer to a screen with a glass screen protector on. The protector was rekt but the phone screen was fine.
Click to expand...
Click to collapse
There are 2 that I would probably recommend. I'm currently using a transparent bumper case off of ebay. I did a review here http://forum.xda-developers.com/google-nexus-5/accessories/lucency-transparent-bumper-case-review-t2690108. It is $2.88 shipped. If you do choose this one, I would stick to black. After using them for a while now, the various colours tend to stain easily, but the black doesn't. It is just for light drop protection, but since the main body is a harder plastic, it won't absorb a higher drop like a softer bumper frame, or a TPU case would. I personally like it because it is transparent and you can still see the sides of the phone and the skin through it.
The other is the replica Nexus 4 bumper, for the Nexus 5. Mine is still in the mail so I haven't tried it out yet, but others have bought it and it seems to have gotten pretty good reviews overall. http://forum.xda-developers.com/google-nexus-5/accessories/replica-official-nexus-4-bumper-nexus-5-t2698422. It's a little bit pricier at $12.99 off Amazon, or around $8 - $10 off Aliexpress.
rochrunner said:
...my naked N5 slipped from my cold, numb fingers and landed flat but face down on a NYC sidewalk a couple days ago. At first it looked like a "soft landing" but no such luck and now I'm looking at a screen replacement (screen itself OK, but glass cracked all to hell).
So now I'm wondering if this could have been prevented simply by a case and not necessarily a screen protector as well. I've used cases such as an Otterbox Commuter in the past but never dropped any of those phones to the extent this one went down. It seems to me that any case with a slight lip on the front -- as most of them must have -- would be enough since the screen itself would not hit the ground.
From research on this forum and web sites I'm currently favoring the Spigen Thin Armor case but am wondering if a high-quality screen protector would also be worth it. My screen at the time it was damaged really had no scratches at all, so the Gorilla Glass was doing its job. Would one of those tempered glass protectors also provide shatter protection? Or would a decent case by itself be sufficient?
FWIW, I've used thin-film protectors in the past but always found them annoying due to bubbles, making the screen less readable, and/or affecting the touch response.
Click to expand...
Click to collapse
There are many choices for thicker protection cases. Properly applied screen protectors don't have any bubbles.
Sent from my Nexus 5 using Tapatalk
Hey! There's a kickstarter project for someone: A case with airbags that deploy when the phone finds itself in free-fall .
Claghorn said:
Hey! There's a kickstarter project for someone: A case with airbags that deploy when the phone finds itself in free-fall .
Click to expand...
Click to collapse
Those sly people at Honda have already done it.
Claghorn said:
Hey! There's a kickstarter project for someone: A case with airbags that deploy when the phone finds itself in free-fall .
Click to expand...
Click to collapse
I don't think I'd feel comfortable having that in my side pocket close to my family jewels or especially not in my back pocket.
BCSC said:
Those sly people at Honda have already done it.
Click to expand...
Click to collapse
Sent from my Nexus 5 using Tapatalk
I want to use my phone without any case. I'm not afraid of scratches, but I'm afraid of screen cracking if I drop my phone. So my question is: if I use tempered glass, will it protect my screen from cracking? Or they will both be cracked? And I also want that glass is the thinnest. So I was thinking about getting 0.15 mm tempered glass. Is it different from 0.3mm or 0.4mm in term of protection, or does only the hardness matter?
Thank you for your reply.
I've dropped mine many many times onto wood and concrete without a screen protector. The phone is a little chipped and scratched, but the screen is absolutely fine.
A nilkin tempered glass screen protector is a good investment as it feels brilliant although when I dropped mine with that on it smashed the corner of the protector.
The edges of the phone are slightly raised so without the screen protector on, a drop onto a flat surface will not damage the screen but will damage the screen protector.
A drop onto a raised surface like a stone would probably break the screen protector but don't know if it'd also damage the screen.
Question is, how often do you drop your phone, and how much do you want to spend on glass protectors?
HtcOneJon said:
I've dropped mine many many times onto wood and concrete without a screen protector. The phone is a little chipped and scratched, but the screen is absolutely fine.
A nilkin tempered glass screen protector is a good investment as it feels brilliant although when I dropped mine with that on it smashed the corner of the protector.
The edges of the phone are slightly raised so without the screen protector on, a drop onto a flat surface will not damage the screen but will damage the screen protector.
A drop onto a raised surface like a stone would probably break the screen protector but don't know if it'd also damage the screen.
Question is, how often do you drop your phone, and how much do you want to spend on glass protectors?
Click to expand...
Click to collapse
I was thinking about Nillkin, but I think it would be too thick. So I'm considering those 0.15 mm protectors in this topic: http://forum.xda-developers.com/htc...5mm-dot-view-friendly-tempered-glass-t2810825
I also thought about xtremeguard, since I use their normal protectors and they are great. It 50$, but with 85% off coupon it's just a few bucks. Only problem is that it's 0.4mm.
Which one would you recommend? I'm planning to spend 10-15$, because 40-50$ is really to much for a protector, in my opinion.
This is the one I use:
ZeroLemon® Ultra Glass Armor - 9H Premium Tempered Glass Screen Protector for HTC One M8
Oditius said:
This is the one I use:
ZeroLemon® Ultra Glass Armor - 9H Premium Tempered Glass Screen Protector for HTC One M8
Click to expand...
Click to collapse
Is it noticable a lot while it's on the phone, since it's 0.3mm?
HTC_One_M8_91 said:
Is it noticable a lot while it's on the phone, since it's 0.3mm?
Click to expand...
Click to collapse
If your looking for it, but after putting on, I haven't paid much attention to it. I dropped my phone once, chipped away at the edges of the shield. The seller replaced it free. I like tempered glass, it is the only screen proctor I will put on my phones. The only bad thing is that it goes edge to edge with the glass. So if you have a case that touches the screen, that might cause a problem. I use a thin clear cars I got off ebay. Works for me.
Ultra 0.5mm Slim TPU Skin Clear new Case Transparent Cover
Oditius said:
If your looking for it, but after putting on, I haven't paid much attention to it. I dropped my phone once, chipped away at the edges of the shield. The seller replaced it free. I like tempered glass, it is the only screen proctor I will put on my phones. The only bad thing is that it goes edge to edge with the glass. So if you have a case that touches the screen, that might cause a problem. I use a thin clear cars I got off ebay. Works for me.
Ultra 0.5mm Slim TPU Skin Clear new Case Transparent Cover
Click to expand...
Click to collapse
The only annoying thing could be top edge, when I pull down notification bar.
Case wouldn't be a problem, because I'm planning to use phone without case, and that why I'm looking for a tempered glass, to protect screen from cracking.
HTC_One_M8_91 said:
The only annoying thing could be top edge, when I pull down notification bar.
Case wouldn't be a problem, because I'm planning to use phone without case, and that why I'm looking for a tempered glass, to protect screen from cracking.
Click to expand...
Click to collapse
Actually then it could be a benefit, because going edge to edge means you will probably not touch the edge. And the edge is not sharp, nice and smooth. The price is cheap enough to try it. I have tried several over the last few months, mostly from China. But this is US born and works and feels great.
I did the steps people have said to do like increase touch sensitivity and re add all the fingers I would use but it still won't work. I don't know who made this protector since I got it off a marketplace site and when I met with the person all he gave me was the screen protector. It was only $5 i got it for so no big deal if it's ****.
Other than that it feels good and everything else works fine.
There are some other threads on here about glass screen protectors. The majority don't work with FP, but there are some that do. Check those threads for info.
In general you need to go for the UV glued type..... All the ones with just glue on the edges will leave an air gap between screen and glass, this heavily impedes with FP functionality.....
Is the brand on Google's approved list?
s3axel said:
In general you need to go for the UV glued type..... All the ones with just glue on the edges will leave an air gap between screen and glass, this heavily impedes with FP functionality.....
Click to expand...
Click to collapse
The air gap has nothing to do with it, the Pixel 6 with its perfectly flat screen has the same problems, my wifes Spigen one has rendered her FPS useless.
MrBelter said:
The air gap has nothing to do with it, the Pixel 6 with its perfectly flat screen has the same problems, my wifes Spigen one has rendered her FPS useless.
Click to expand...
Click to collapse
Thanks, maybe the cause is not as simple as I assumed... Still my experience remains over many phones: the edges-only glued glass protectors just don't work (for me )
s3axel said:
Thanks, maybe the cause is not as simple as I assumed... Still my experience remains over many phones: the edges-only glued glass protectors just don't work
Click to expand...
Click to collapse
I'm not disputing that, i was just clarifying the Pixel 6 suffers the same problem even with a flat screen.
Never had a problem with a 1+ phone using a glass protector over the FPS even with the cheapest crap i could find so as far as i am concerned all the reasons Google are coming out with are absolute cobblers.
So should I just take this thing off or wait for a software update from Google?
I for myself have installed a TPU screen protector presently, awaiting delivery of a UV glass protector as I like those more
I'd hope Google improves the behaviour of the FPS, in how far however I don't know.....
I am currently using the below TPU screen protector and could not be happier with it. My fingerprint scanner works nearly every single time and I have not had an issue. Once the screen protector has been properly applied (I admit, I screwed it up the first time) I cannot even tell that it is on my screen visibly or by touch.
Having said that, I am a little concerned that a TPU screen protector is not as good in general as a glass one. I have not had an issue yet, but I also have not had an accidental drop or anything.
I will also say that I have registered each of my thumbs twice. I will get an occasional "longer" read, and by longer, maybe a half a second longer. However, I have noticed that when that happens, my thumb is slightly out of the read circle. When my thumb is dead center, it reads it every time really quickly.
I am not all that excited about a UV glass protector as I have read horror stories of discoloration and some users not being able to get them off.
Supposedly Google has released their approved screen protectors list. I am not about to spend 50 bucks on a Zagg. The one for Panzer was more reasonable, but it disappeared off their website. The Otterbox is another TPU and I like the one I have:
Amazon.com
I might just take this off and use nothing. I didn't use a protector for my s7 edge or s10+ and didn't get a single scratch. I only got it because I wanted to preserve the oilyaphobic coating. This thing only cost me $5 in the end
Did peeps make sure to use the increased screen sensitivity setting for use with screen protectors?
KedarWolf said:
Did peeps make sure to use the increased screen sensitivity setting for use with screen protectors?
Click to expand...
Click to collapse
yes, it makes zero difference.
Typically with curved screens, you need a full-screen adhesive in order for the FPR to work after installation. Either that, or one with edge adhesive with an area over the reader that also sticks to the screen, but I personally think those are kinda ugly. For the regular P6, my girlfriend ordered a brand called "TOCOL" for a glass protector, which is working great all around.
If/when Whitestone Dome releases one for the P6P, that will be the only really good option. It's either that, or buy an edge adhesive style one, buy LOCA glue and a UV lamp, and DYI it. Only way you're going to have glass and a working FPR.
I'm using a TPU protector and a case. TPU has come a long way tbh, the dry install ones I got feel like a naked screen and give me some piece of mind in regard to small scratches. The case does the rest as far as drop protection. Victus Glass is pretty good for shatter resistance generally, but crap for scratches.
OP, I would remove that one if you want to use the Fingerprint Reader. There isn't a software update that's going to solve that problem unfortunately. I'd just use a decent TPU for now and if you really want glass after you try it still pray for Whitestone Dome. There's another thread on here dedicated to working protectors, I'd check that out and pick one.
Pixel 6 Pro screen protector
Hi all, I have a few questions around tempered glass screen protectors for curved screens like the Pixel 6 Pro, I was wondering if people had any answers to: Are there any known brands that do good quality curved tempered glass screen...
forum.xda-developers.com
orlans21 said:
I did the steps people have said to do like increase touch sensitivity and re add all the fingers I would use but it still won't work. I don't know who made this protector since I got it off a marketplace site and when I met with the person all he gave me was the screen protector. It was only $5 i got it for so no big deal if it's ****.
Other than that it feels good and everything else works fine.
Click to expand...
Click to collapse
If you prefer the 9H glass protectors, you'll have to find a glass protector that is "Google certified" to work with fingerprint reader.
These are glued to the screen to make 100% positive contact with the glass protector.
I'm guessing you have a 9H glass protector like mine that has a very small air gap between the screen and the protector. Even with the enhanced fingerprint reader setting, my fingerprint reader doesn't pick up anything.
The TPU flexible protectors supposedly work well, but I like the 9H glass protectors.
The Google Certified 9H glass protectors that I've found are between $15 - $39 per protector, and many of them are "out of stock" at the moment.
MrBelter said:
The air gap has nothing to do with it, the Pixel 6 with its perfectly flat screen has the same problems, my wifes Spigen one has rendered her FPS useless.
Click to expand...
Click to collapse
Yeah it's only the Pro model that has curved screens and requires UV glue protectors, which there is currently none available until Whitestone Dome releases. I managed to get this and it works perfectly but it's already out of stock [3 Pack]Google Pixel 6 Pro Screen Protector,Akcoo Liquid UV Tempered Glass [Full Screen Adhesive][Edge to edge coverage][Compatible with fingerprint sensor] for Pixel 6 Pro 6.7 inch https://www.amazon.com/dp/B09KC72DW...abc_YW4QX456AX8GJ33BV928?_encoding=UTF8&psc=1
orlans21 said:
So should I just take this thing off or wait for a software update from Google?
Click to expand...
Click to collapse
Have you tried to delete the finger print and add a new one?
lucky_strike33 said:
Have you tried to delete the finger print and add a new one?
Click to expand...
Click to collapse
yeah, i got rid of the protector. it was garbage