Hello everyone. I am having a grave issue with my Red Magic 5G.
Whenever I try to update my firmware to a newer version, whether it's from OTA or OTG, whenever it tries to update itself, it keeps giving me an error that tells me "Install Package Failure" whenever it reaches 24% installation.
I have tried a factory/hard reset, as well as a complete wipe and reformat using TWRP, but still can't get the phone to update properly. How can I fix this? Thank you.
Same issue here. But I think as long as the phone works it should be fine not updating it. The only problem I see here is the update notification that can be annoying sometimes.
However I really would like to know why this happens, why doesn't the phone want to install the update?
My current version: NX659J_ENCommon_V8.12
Version that fails to install: NX659J_ENCommon_V8.57
Btw, does "EN" in the version name stand for "European Nations" (Europe) , do I have the European firmware version?
Related
Hi All,
I've done numerous updates on my BA lately, but this last time the update hung during the radio portion. Now, the unit is stuck in it's update mode (You know... blank screen except for saying USB or SERIAL at the top, and a version number atthe bottom), and every time I try to do an update of any kind it hangs giving error number 120 which apparently indicates that I'm attempting to install an update that doesn't match the country (and I assume language) of the unit.
Anyone seen this before? Anyone know how to get around it? I've tried using every update I can find, including those that have installed properly in the past. HELP!!!
Thanks! )
A few days ago I've installed the unofficial CM9 on my dear old buzz, precisely the 2012.09.20 version from this thread by ErwinP. Almost immediately the OTA (off-the-air?) updater informed me that an update is available.
A few details: even if the current CM9 buzz snapshot is marked as 2012.09.20 the OTA says it is 2012.08.18; this has been explained by one of the mantainers as being normal. FOr the same reason, the update is marked as 2012.08.30, but I did not worry about it.
Anyway, whenever I try to download the update after a few seconds I get a notify message "md5 error - downloaded file invalid!" and stops. If I then browse the SD card I find an "OTA updater/download" directory, which is empty.
My question is: is this behaviour normnal, i.e. because of the ROM being unnoficial it does not have OTA updates? Am I the only one experiencing this problem?
Thank you in advance
Don't download the update - you have a newer version than that. OTA updates are meant to work, but since the build.prop hasn't changed (it's hard to change) than it will always display an older version and want you to update.
Hey everyone,
So two night ago I received a notification on my GS3 saying a new update was out.
When I tried installing the update it rebooted into recovery and failed at 24%....weird. I was running Rogers stock rom and recovery at the time so this shouldn't have happened, and I would like to know why for future reference.
I also tried updating via samsung kies. But when I tried this, it said my device wasn't compatible to update via kies????
So I ended up download the LK4 update off sammobile website and installed it using odin.
Anyways, I now have the new update installed. I've noticed two weird things:
1. When I go to about phone in settings and go into software update, it shows a screen "checking for software updates..." and doesn't go away unless I press back or home button. Why can't I search for new updates????
2. My google now voice isn't working. It recognizes what I say to it but when it gives the flashcard response, it doesn't talk back like it normally does. I have it set to English US, and yes my media volume is up at full volume.
Anyways I'm a little frustrated at this point. I can't figure out how to fix these problems so any help would be greatly appreciated. Thanks
As i've wrote in another Thread (Bootloop at M1D64T), my SWR50 has this behaviour since this Update.
So, i've manually rolled back to Lollipop - discribed in the Thread " How to Fix SWR50 with working Fastboot".
Now, everytime the Watch comes at the Point to Update from Lollipop to Marshmallow, it's endet in the Bootloop with the four Dots...all Updates to higher Lollipop-Versions works like a charm...
Another strange observation i've made when i tried to change to the chinese Fitware....all went fine, but i don't like these Software and rolled back to AW. The Fitware put my Watch back to LDZ22D.
The Watch seddle up, all was fine and after a while the Watch want performe an Update. At the the end from the Update, the Watch booting, but it don't show the circling Clock, no, the four Dots come up, but only for two seconds, then the Watch stays in Recovery...no warning about a failed Update...After i've booting manually from Recovery to System, all runs good and the Watch was on LDZ22D.
So at this point, it can't be the Update to LCA43 by OTA, the Watch says im at the actually system...
Now i will try an manually update to LCA43 and ignore the Update Message to MM....
I'll hope, Sony release an Update to correct this Issue...
Hey all
I recived the miui 12.5 enchanced [ALIOTHEEAGlobal_V12.5.3.0.RKHEUXM] (2.9 GB & 466 MB) Update a few days ago via ota. My rom is stock - no root or custom Recovery. The download and installing process work fine, but then the Phone need to restart. While restarting the Phone stuck at poco Logo. Only with a few reboots (or leave it alone for a long time) the Phone comes alive again. Then there is the Info miui update failed after reboot. I also tried to Update manually the Full and increment Rom over the three dots menue. No Chance. Even if i install my current rom version [ALIOTHEEAGlobal_V12.5.3.0.RKHEUXM] again - the same problem
I searched the whole Internet and couldn't find someone with the same problem.
Please help.. Thank yo all!
FYI: I cannot do a full reset / wipe with data loss, because i have so much banking apps and accounts. I need a full day of restoring my current status and i don't have the time at the moment.
No one?
Hmm... I don't know if it possible with locked BL but try boot from B partitions? Are they for cases like this one, aren't they?
I dont know this option. How will this work?
I backed up my phone as good as possible und tried to flash with "XiaoMitTool V2" my currend rom and the 12.5.6.0 and it always endet in "miui sideload failed". WTF is here going wrong .. While sideloading it stops at 4.99% on phone screen.
Have you tried with 12.5.6 via stock recovery? (full rom ofc, not OTA). It doesn't erase your data.
I also tried ToolV2 with my F3 and no luck too.
isnt 12.5.6 eea enchanced? 12.5.3 is older update in eu
I tried to update through stock recovery and MIAssistant but no success. Like @crysus said, it stops to 4,99 on phone screen, no error but it boots to the old ROM. Maybe because is a stable beta version.
Mine updade went all good without hassles. I updated it via stock recovery but first I use 3 dots menu in system updater app just to show where update file is. (full recovery fw used, not just OTA).
The fastboot version of 12.5.6_EEA has been available for a few days now, it can be Flash with miflash.
Here the link:
Xiaomi Firmware Updater
The ultimate script that provides firmware packages for Xiaomi devices.
xiaomifirmwareupdater.com