I just rooted my device, here is how to do it.
Installation
The Magic Mask for Android
topjohnwu.github.io
1. OEM unlock (All data will be lost and warranty void.)
2. Download latest firmware
3. Install Magisk APK - Upliad AP file.
4. Run magisk on AP file
All data will be lost.
Flash with Odin without HOME folder.
Done.
Firmaware from samsung website + magisk modified one (uploading now, will take some time):
13.08 GB folder on MEGA
6 files
mega.nz
Any alternative to Odin? I've given ADB a try since my only device with usb c is a linux. This command:
└──╼ $fastboot flash boot_a magisk_patched-23000_H7hbm.img
fails with something about "command unknown" : (
Very optimistic since you managed it there's a point to keep trying
Not a very detailed how-to, but it gets the job done. I successfully rooted my SM-A725M/DS with this method.
Thanks.
I just installed TWRP, Kakarot Kernel without bricking my phone
Hello. I downloaded all the necessary files, but I don't know the procedure of what to do with those files.
I would ask you if you can write me detailed instructions.
Thanks in advance
As written in the original post:
Flash with Odin without HOME folder.
After you flash it and device starts - run Magisk app, it will need to finalize root. Than run Root checker app to see if it worked.
Download Odin, run it - select files and flash.
Check some tutorials for it if you are first timer, lots of videos on youtube.
instill couldn't root my a72f
Hello Dear Friends, I have been struggling for a couple of days to root my Samsung A72 ( SM-A725F/DS)
Android 11 baseband version ( A725FXXU3AUG2 )
OEM unlocking is already unlocked.
but when I'm going to download mode it shows the following:
FRP LOCK: OFF
OEM LOCK: ON
KG STATUS: CHECKING
I tried a lot to flash TWRP or patched boot image with magisk. it never worked.
I also reflashed the whole firmware it didn't work
several times I turned it off and on the OEM unlocking still did not work.
I did a lot of googling and I found that I should unlock OEM via fastboot.
I installed ADB and android drivers on my windows 10
I tried that too here is the below log:
Microsoft Windows [Version 10.0.19043.1237]
(c) Microsoft Corporation. All rights reserved.
C:\Users\Sher>adb devices
List of devices attached
RZ8R31HB8RB device
C:\Users\Sher>adb reboot bootloader
C:\Users\Sher>fastboot devices
RZ8R31HB8RB fastboot
C:\Users\Sher>fastboot flashing unlock
...
FAILED (remote: unknown command)
finished. total time: 0.006s
C:\Users\Sher>fastboot oem unlock
...
FAILED (remote: unknown command)
finished. total time: 0.004s
C:\Users\Sher>fastboot reboot
rebooting...
finished. total time: 0.001s
C:\Users\Sher>
when I'm trying to check if the fastboot commands works or not I tried to reboot the phone it did not work as you see in the above command.
I tried 3 different computers it never worked for me.
can you please guide and help me on how to unlock OEM on my A72 phone?
your help and support will be appreciated
regards,
Sher
fairylights said:
Any alternative to Odin? I've given ADB a try since my only device with usb c is a linux. This command:
└──╼ $fastboot flash boot_a magisk_patched-23000_H7hbm.img
fails with something about "command unknown" : (
Very optimistic since you managed it there's a point to keep trying
Click to expand...
Click to collapse
Heimdall
Will this work for A72M, Mexico version?
If I remember correctly I had to change device date over a month to the future to be able to fully OEM unlock it in dev oprions, after initial OEM unlock was done. It is timed.
madseason.live said:
I just rooted my device, here is how to do it.
Installation
The Magic Mask for Android
topjohnwu.github.io
1. OEM unlock (All data will be lost and warranty void.)
2. Download latest firmware
3. Install Magisk APK - Upliad AP file.
4. Run magisk on AP file
All data will be lost.
Flash with Odin without HOME folder.
Done.
Firmaware from samsung website + magisk modified one (uploading now, will take some time):
13.08 GB folder on MEGA
6 files
mega.nz
Click to expand...
Click to collapse
I didn't think it work, but it did. I tried a few different methods over the last few days and I just couldn't get a recovery running or a magisk modified (about 100mb) boot.img file uploaded through Odin. Thank you very much for this post.
1. OEM unlock (All data will be lost and warranty void.) Enable USB debugging.
2. Download latest firmware to PC
3. Install Magisk APK from github on phone (keep a copy on the sd card to survive wipes for convenience)
4. Copy the (about 6GB) AP file from the firmware package on pc to the phone
5. Run Magisk on the AP file
6. Copy the magisk_patched-xxxxx_xxxxx.tar that is generated by Magisk to PC
7. Boot phone in download mode. Run ODIN and flash the magisk_patched-xxxxx_xxxxx.tar under AP (no other fields need to be populated)
8. Phone will auto reboot and factory reset itself. Install all your accounts as this will be the final working version of your phone.
9. Install Magisk again and it will do the final config and reset the phone.
10. Enjoy. Install root checker to confirm. Test with a rooted app like vanced.
Hi guys,
Can you confirm that magisk on A72 shows "Ramdisk: yes" ?
(I want to get this phone, but want to avoid getting root only via recovery like on S10 that doesn't have ramdisk)
- removed-
tomhet said:
Hi guys,
Can you confirm that magisk on A72 shows "Ramdisk: yes" ?
(I want to get this phone, but want to avoid getting root only via recovery like on S10 that doesn't have ramdisk)
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
madseason.live said:
View attachment 5513341
Click to expand...
Click to collapse
Good recovery instal
Related
Rooting your device may cause loss of warranty.
1. Check your device model - This guide is for HTC Desire Eye and its variants including AT&T Model and International Unlocked Model only.
2. Backup - Backup is mandatory since bootloader unlock will erase your device to factory.
Requirentments- First you should have bootloader unlocked device. (Please visit "http://www.htcdev.com/bootloader" to unlock your bootloader)
Installed ADB Drivers and files - tool can found here, link - https://drive.google.com/file/d/0B9SWmcUAdoOnOVpITTVtcFZUZUk/view?usp=sharing
Download your recovery.img here, link - https://drive.google.com/file/d/0B9SWmcUAdoOnc3hOLXpWVVFIc2c/view?usp=sharing
Super SU & binary here, link - http://download.chainfire.eu/593/SuperSU/BETA-SuperSU-v2.19.zip?retrieve_file=1
Put recovery.img to your ADB folder in PC, and super su to your mobile.
3. Now start command line in the ADB folder where your files located in the PC (Right click + hold down Shift) then "Open command window here"
Guide - http://www.tech-recipes.com/rx/232/right-click-to-open-a-command-prompt/
4. Run following commands to flash recovery.img to your device ( this will replace your original recovery)
fastboot flash recovery recovery.img
Simple.. Now reboot into recovery by pressing power+vol down, then select recovery in the loading screen (if you have any issues rebooting into loader screen please try after disable quick boot in power settings).
5. Now flash your Super SU (Zip) transferred to your mobile by selecting in the recovery.
Everything good to go after reboot.....!!!!
I flashed the recovery image and it keeps coming up with a little screen with a red triangle,any ideas? thanks
pimpsuprazx said:
I flashed the recovery image and it keeps coming up with a little screen with a red triangle,any ideas? thanks
Click to expand...
Click to collapse
Bootloader unlocked?
Can you post a screenshot (PIC) ?
That what happened after flashing the recovery.img and booting into recovery:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
johnyboo said:
That what happened after flashing the recovery.img and booting into recovery:
Click to expand...
Click to collapse
Same problem here.. Really sad.. Was the recovery image working???
jolishj said:
Same problem here.. Really sad.. Was the recovery image working???
Click to expand...
Click to collapse
Odd that there a few having problems. I s-off'd and had this recovery installed very easily. Are you all still having problems?
unforseenenemy said:
Odd that there a few having problems. I s-off'd and had this recovery installed very easily. Are you all still having problems?
Click to expand...
Click to collapse
the same issue here
like the recovery is not compatible
Try using the recovery found here: http://forum.xda-developers.com/desire-eye/development/recovery-twrp-2-8-4-0-htc-desire-eye-t3008442
I have rooted my phone, But when I uninstall any system app using system app remover after restarting app will be back, and I can't uninstall them.
What's the problem??
karo222 said:
I have rooted my phone, But when I uninstall any system app using system app remover after restarting app will be back, and I can't uninstall them.
What's the problem??
Click to expand...
Click to collapse
System write protection.
There is a mod to disable that here: http://forum.xda-developers.com/des...e-disable-write-protection-v1-0-tool-t2966850
Or use a custom ROM, those have it disabled already.
I went through all the necessary steps. Only thing/issue now is the actual flashing of the root file. It will not take. Anyone else have this issue? Is there a way to get the necessary binary or whatever it's asking for? Thank you in advance.
-Carlos
I have exactly the same issue
hondalude89 said:
I went through all the necessary steps. Only thing/issue now is the actual flashing of the root file. It will not take. Anyone else have this issue? Is there a way to get the necessary binary or whatever it's asking for? Thank you in advance.
-Carlos
Click to expand...
Click to collapse
Only you have to Download BETA-SuperSU-v2.71-20160331103524.zip and flash it. Issue Solved
I did all the steps and everythign went fine, but then I downloaded a RootChecker app and it says I dont have root access. How can I make sure everything worked? NVM I GOT IT FIXED THANX ALOT FOR THIS POST!!!
Shameera_N said:
Rooting your device may cause loss of warranty.
1. Check your device model - This guide is for HTC Desire Eye and its variants including AT&T Model and International Unlocked Model only.
2. Backup - Backup is mandatory since bootloader unlock will erase your device to factory.
Requirentments- First you should have bootloader unlocked device. (Please visit "http://www.htcdev.com/bootloader" to unlock your bootloader)
Installed ADB Drivers and files - tool can found here, link - https://drive.google.com/file/d/0B9SWmcUAdoOnOVpITTVtcFZUZUk/view?usp=sharing
Download your recovery.img here, link - https://drive.google.com/file/d/0B9SWmcUAdoOnc3hOLXpWVVFIc2c/view?usp=sharing
Super SU & binary here, link - http://download.chainfire.eu/593/SuperSU/BETA-SuperSU-v2.19.zip?retrieve_file=1
Put recovery.img to your ADB folder in PC, and super su to your mobile.
3. Now start command line in the ADB folder where your files located in the PC (Right click + hold down Shift) then "Open command window here"
Guide - http://www.tech-recipes.com/rx/232/right-click-to-open-a-command-prompt/
4. Run following commands to flash recovery.img to your device ( this will replace your original recovery)
fastboot flash recovery recovery.img
Simple.. Now reboot into recovery by pressing power+vol down, then select recovery in the loading screen (if you have any issues rebooting into loader screen please try after disable quick boot in power settings).
5. Now flash your Super SU (Zip) transferred to your mobile by selecting in the recovery.
Everything good to go after reboot.....!!!!
Click to expand...
Click to collapse
It is not working on my HTC DESIRE EYE
Error: The code execution cannot proceed because RAPI.DLL was not found.
Troubleshooting steps:
1. Make sure the downloaded file is unzipped
2. USB Debugging enabled
3. On my phone i selected the option, USE USB FOR: "usb file transfer"
4. On my phone I also tried selecting the option, USE USB FOR: "CD Installer"
5. Restart Phone, Mobile and the downloaded file
source code here:
https://github.com/jemyzhang/iovyroot/tree/nokia-n1
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Since the system is verity on, seems no more things can do.
iovyroot binary for nokia n1:
20160922: View attachment iovyroot.n1.zip
After get the root privilege, boot and recovery can be flashed by dd, with the recovery, the corresponding update package can be flashed by adb sideload.
And also, the boot can be repack for verity off and also the selinux can be disabled.
- turn off selinux
add cmdline parameter: androidboot.selinux=permissive
- turn off system verity
change the fstab, remove "verify" option
How to use it?
Any guide or root step?
jemyzhang said:
iovyroot binary for nokia n1:
20160922: View attachment 3883559
Click to expand...
Click to collapse
latheliao said:
How to use it?
Any guide or root step?
Click to expand...
Click to collapse
ZIP-file with binary attached by jemyzhang contains a guide. Seems to be quite simple to follow.
I can't test it as I'm still on 5.0.2 (CN rooted, but for unkown reasons still unable to flash to FM version) - but it's probably worth a try for those who have already updated to CN or FM 5.1.1 and are stuck with a non-rooted N1.
If there are any voluntaries - please post detailed report. N1-community would definitely appreaciate it! It is such a beautiful device.
It would be especially great if someone with a CN 5.1.1 could report success (I guess it would be a three-step-approach: rooting CN 5.1.1, then switching to FM 5.1.1, then probalby necessary to root again?)
I will test this when I have time (later this week I hope). I will definetely post a guide if I succeed with this.
the boot partition is verity off, you can flash the recovery(FM) to the boot partition, and flash the FM package with sideload.
Hi Jemy,
Really appreciate your work on Nokia N1 and I'm so glad that it is possible to root devices with A5CNB19. However, as a rookie, I have no idea how to follow your guidance and successfully root the tablet. Could you please update some detailed instructions on how to root this device? Thanks again for your kindly work on this tablet.
David
jemyzhang said:
the boot partition is verity off, you can flash the recovery(FM) to the boot partition, and flash the FM package with sideload.
Click to expand...
Click to collapse
steps for change rom from A5CNB19 to A5FMB19
stock recovery of A5FMB19: View attachment recovery.img.zip
for whom want to flash from A5CNB19 to A5FMB19.
A5FMB19 rom download: A5FMB19_update.zip
Important: bootloader must be unlocked. If the bootloader was locked, boot partition will also be verified.
- Unlock bootloader
Attention: data will be lost if you unlock your device
1. enter into fastboot by hold power and volume up key while power on
2. use the following command to unlock the bootloader
Code:
fastboot oem unlock
3. choose "Yes" in the next screen
Steps for flash:
1. boot into fastboot
2. flash recovery image with the following command:
Code:
fastboot flash boot recovery.img
3. boot into 'normal' mode, this will actually boot into recovery
4. press "power" + "vol up" key, which will leading to the text mode
5. choose "apply update from ADB" and confirm with power key
6. upload stock FMB19 package with sideload from pc:
Code:
adb sideload A5FMB19_update.zip
steps for rooting A5FMB19
[Download Section]
- original boot image for FMB19:View attachment boot-A5FMB19.img.zip
- custom recovery: View attachment n1_twrp_fmb19.img-by-jemyzhang.zip
- magiskv6: View attachment Magisk-v6-for-nokia-n1-mod-by-jemyzhang.zip
---- apk: View attachment Magisk_Manager_v1.2.apk
- superuser: View attachment phh-superuser-17-magisk-for-x86-64-mod-by-jemyzhang.zip
---- apk: install from play store me.phh.superuser
magisk v7: pull request has been pushed, waiting for merge.
[Preparation]
Code:
adb push boot.img /sdcard/
adb push Magisk-v6-for-nokia-n1-mod-by-jemyzhang.zip /sdcard/
adb push phh-superuser-17-magisk-for-x86-64-mod-by-jemyzhang.zip /sdcard/
[flash twrp recovery]
first of all unlock the boot loader
1.1. boot into fastboot
1.2. flash recovery image with the following command:
Code:
fastboot flash boot n1_twrp_rec.img
1.3. boot into 'normal' mode, this will actually boot into recovery
[restore boot image]
- restore back the orignal FMB19 boot image:
flash boot.img from recovery(switch to image mode)
[flash magisk and phh-supersu]
That's all
[Anything not ready for twrp]
1. adbd, usb connection error
2. graphic, low performance for text display
3. no signature:::: so flash into recovery partition is impossible
How to unlock boot loader??
Any one try the method? N1 can not unlock bootloader by command from adb before.
Sent from my Redmi Note 3 using XDA-Developers mobile app
Fail to root A5FMB19
I have tried "steps for rooting A5FMB19", but I failed.
As you say, first I adb push three files to the sdcard of N1. Then I unlock the bootloader. But when I unlock it, all the data in the tablet will be cleared.
So, when I want to flash boot.img from recovery, I can't find them in my tablet.
damoguyanzero said:
I have tried "steps for rooting A5FMB19", but I failed.
As you say, first I adb push three files to the sdcard of N1. Then I unlock the bootloader. But when I unlock it, all the data in the tablet will be cleared.
So, when I want to flash boot.img from recovery, I can't find them in my tablet.
Click to expand...
Click to collapse
me too
---------- Post added at 09:59 AM ---------- Previous post was at 09:54 AM ----------
do you have the recovery of A5CNB19，i wanna go back to that version, thank you very much
I have taken your step to root my device . However the twrp failed to mount /data and unable to mount storage .
So could you help me to solve this problem ?
Thank you !
damoguyanzero said:
I have tried "steps for rooting A5FMB19", but I failed.
As you say, first I adb push three files to the sdcard of N1. Then I unlock the bootloader. But when I unlock it, all the data in the tablet will be cleared.
So, when I want to flash boot.img from recovery, I can't find them in my tablet.
Click to expand...
Click to collapse
any solution?
realceday said:
any solution?
Click to expand...
Click to collapse
fist unlock the divice, then restart to the system, if the restart doesn't work, you should flash "fastboot –w" in the fastboot modle。after that, copy the files into your divice, then go to the fastboot and flash twrp。
if you can read chinese, read baidu tieba, goto the nokian1 section(i can't post the url)
Have anyone succeeded with this method ?
I can confirm this working.
Several notes to make:
1. from what I understand, the iovyroot method is only POC, and unrelated to the second approach. ( I actually tried this approach and couldn't get root access)
2. the second approach works for me. Note that both magisk and phh-supersu require two steps of installation: first flash in recovery, and install the correspoding apk in android.
Thank you jemyzhang!
Not able to push the iovyroot.n1 it says : permission denied . even in recovery as in fastboot as in normal boot
i'm actually using A5FMB19
Hi everyone
My phone model is xt2075-3,I want to root
Can I directly flash the latest magisk(20.4) to get root permission after unlocking BL?
I've succeeded in getting root.The steps are as follows
1.Download the twrp for your mobile phone,and magisk20.4.zip,magisk 7.5.1.apk
2.Visit Motorola official unlock website to unlock BL
3.You have 2 choice,A.boot on twrp one time;B.flash twrp;I choose A
4.Whatever your choose,in the twrp,install magisk zip,after done,reboot system
Enjoy root!
If you use the Magisk Manager to patch the boot image manually, and then flash that through fastboot - will that work also?
(My phone has yet to arrive so can't test this just yet...)
Update : i got the 8gb ram 128gb varient and i could boot into twrp from fastboot but i cannot flash replacing stock recovery nor i can see the internal or external memory due to decryption error
However, i basically unlocked boot loader and booted in fast boot then i flashed the patched boot.img ( installed magisk apk and added the stock boot.img inside the phone to patch it) then copy it back to pc and flashed it in fastboot mode and now i got root access
NOTE : if you happen to do something wrong you cannot use rescue and backup software to restore your phone to stock again ... flash stock boot.img in fastboot first so the software will recognize the phone back again
sniper9911 said:
Update : i got the 8gb ram 128gb varient and i could boot into twrp from fastboot but i cannot flash replacing stock recovery nor i can see the internal or external memory due to decryption error
However, i basically unlocked boot loader and booted in fast boot then i flashed the patched boot.img ( installed magisk apk and added the stock boot.img inside the phone to patch it) then copy it back to pc and flashed it in fastboot mode and now i got root access
NOTE : if you happen to do something wrong you cannot use rescue and backup software to restore your phone to stock again ... flash stock boot.img in fastboot first so the software will recognize the phone back again
Click to expand...
Click to collapse
where did you find the boot.img and the patched one?
Thanks
Mr.Krulez said:
where did you find the boot.img and the patched one?
Thanks
Click to expand...
Click to collapse
Get the full stock image by downloading rescue and smart assistant app from lenovo which supports moto phones ... Do login and get the fastboot rescue option while plugging your phone in the pc in fastboot mode .. then it will download it full firmware for your varient
Becareful that continue to flash the firmware will wipe your phone completely
After that get a copy of the boot.img file ... Copy it to the internal memory and install magisk manager apk from its official github site ... Now patch the boot.img you copied in your phone inside the magisk app then copy it back to your pc
Lear how to flash it from fastboot
Flash it
Done .. you are now rooted by patched boot.img with stock recovery !
Sent from my moto g 5G plus using Tapatalk
View attachment 5143479View attachment 5143477View attachment 5143481
Thank you for the answer but if I want to just root my phone I only need to flash magisk right? i don't need the patched boot.img?
sorry to bother you but the last phone I used supersu withouth flashing anything else than the recovery
Hi Guys,
my device is a/b device, bootloader unlocked, could you please kindly advise to flash twrp
what is the fastboot command, i use fastboot flash recovery twrp.img and i get a bootloop . the command fastboot boot twrp.img runs twrp onece and its fine, but how do i flash it please?
thanks and kind regards
emanuel said:
what is the fastboot command, i use fastboot flash recovery twrp.img and i get a bootloop . the command fastboot boot twrp.img runs twrp onece and its fine, but how do i flash it please?
Click to expand...
Click to collapse
I think the flash method fails because there is no partition called "recovery" - as an A/B device it looks like there are two:
Code:
nairo:/ $ ls -l /dev/block/by-name/ | grep recovery
lrwxrwxrwx 1 root root 16 1970-05-20 07:34 recovery_a -> /dev/block/sdd20
lrwxrwxrwx 1 root root 16 1970-05-20 07:34 recovery_b -> /dev/block/sdf20
if you have the Magisk zip file on the internal storage you can use the "fastboot boot twrp.img" method to flash it from there (for some reason TWRP can't see the SD card on my device)
Now for my question... my rooted (UK Retail) device has indicated that there is an OTA update:
I've tried using the method described here to restore the boot partition to stock so that it doesn't interfere with the process, but it fails (see attached images).
Does anyone know of a working method? I have downloaded the full (2+GB) update so am prepared to flash that (and restore everything else from backups) if necessary - but would rather not if it can be avoided...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
xth88312 said:
I've succeeded in getting root.The steps are as follows
1.Download the twrp for your mobile phone,and magisk20.4.zip,magisk 7.5.1.apk
2.Visit Motorola official unlock website to unlock BL
3.You have 2 choice,A.boot on twrp one time;B.flash twrp;I choose A
4.Whatever your choose,in the twrp,install magisk zip,after done,reboot system
Enjoy root!
Click to expand...
Click to collapse
Hi @xth88312 ,
can you give the link you used to download TWRP for Moto XT2075-3?
I unlocked my phone through the official Motorola site:
Unlocking the Bootloader | Motorola Support US
Visit the customer support page to view user guides, FAQs, bluetooth pairing, software downloads, drivers, tutorials and to get repair and contact us information.
motorola-global-portal.custhelp.com
I downloaded the latest Magisk and MagiskManager in the same directory from
Releases · topjohnwu/Magisk
The Magic Mask for Android. Contribute to topjohnwu/Magisk development by creating an account on GitHub.
github.com
I downloaded the original firmware from https://mirrors.lolinet.com/ and extracted the boot.img in the same directory, then issued, through the ADB connection:
Code:
adb install ./MagiskManager-*.apk
adb push ./boot.img /sdcard/Download/
(Replace the star as needed)
I opened MagiskManager app (you need to be connected to the Internet) and in the Magisk card I tapped Install > "Select and Patch a File". I browsed for and selected /sdcard/Download/boot.img and tapped "Let's go". A patched image /sdcard/Download/magisk_patched_*.img is created. Then, through the ADB connection, I issued:
Code:
adb pull /sdcard/Download/magisk_patched_*.img
adb reboot bootloader
fastboot devices
fastboot flash boot magisk_patched_*.img
fastboot reboot
At reboot, the phone was rooted.
boringtech said:
Hi @xth88312 ,
can you give the link you used to download TWRP for Moto XT2075-3?
Click to expand...
Click to collapse
[RECOVERY][UNOFFICIAL] TWRP 3.5.0.0
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and...
forum.xda-developers.com
thats the link for twrp for moto g 5g plus..
use at own risk as i havent tried it myself so im not responsible for bricked devices etc...FLASH AT OWN RISK....
Mr.Krulez said:
Thank you for the answer but if I want to just root my phone I only need to flash magisk right? i don't need the patched boot.img?
sorry to bother you but the last phone I used supersu withouth flashing anything else than the recovery
Click to expand...
Click to collapse
Mr.Krulez said:
Thank you for the answer but if I want to just root my phone I only need to flash magisk right? i don't need the patched boot.img?
sorry to bother you but the last phone I used supersu withouth flashing anything else than the recovery
Click to expand...
Click to collapse
youll have to patch bo
Mr.Krulez said:
Thank you for the answer but if I want to just root my phone I only need to flash magisk right? i don't need the patched boot.img?
sorry to bother you but the last phone I used supersu withouth flashing anything else than the recovery
Click to expand...
Click to collapse
you need to
Mr.Krulez said:
Thank you for the answer but if I want to just root my phone I only need to flash magisk right? i don't need the patched boot.img?
sorry to bother you but the last phone I used supersu withouth flashing anything else than the recovery
Click to expand...
Click to collapse
youll need the patched boot.img to gain root, thats how ive had to root all my moto phones ive had, never been able to just flash supersu etc, someone will jump in if im wrong but as far as i know you need to patch the boot.img....
Remember everything you do is at your own risk i take no responsibility for.what you do with your device
Hello forum,
I wanted to breathe new life into my old G4 H815, but I didn't come very far, because some commands behave not as expected. Here are the facts:
1.
Bash:
adb reboot bootloader
always works and sets up the device in fastboot mode.
2.
Bash:
fastboot devices
recognises the device.
3.
Bash:
fastboot flash recovery twrp.img
gives positive feedback, though it seems not to work properly, because when it restarts afterwards and asks me if it should wipe all data it wipes the data and doesn't start TWRP.
4.
Bash:
fastboot boot twrp.img
doesn't reboot into recovery mode.
5. I used
Bash:
fastboot getvar all
to make sure that the device is unlocked.
6.
Bash:
adb reboot recovery
takes the phone to recovery mode, but then it stops with a "no command" message and an image with a red triangle and a dead Android robot appears. I pushed all possible button combination, but I couldn't enter the recovery menu.
The phone doesn't have any hardware issues and is basically in a good condition. How can I pinpoint the error?
Try removing the stock recovery before flashing TWRP. Use fastboot erase recovery
Make sure to have a backup for stock recovery should you need to flash it ever again.
Or after flashing TWRP disconnect from PC and use button combination to boot to recovery.
Thanks, but how can I backup the stock recovery? The recovery is located in the /dev directory:
Bash:
lrwxrwxrwx 1 root root 21 2015-01-01 01:00 recovery -> /dev/block/mmcblk0p39
I tried to copy the recovery to the SD card:
Bash:
cat /dev/block/mmcblk0p39 > /sdcard/recovery.img
However, it didn't work, because I get a "Permission denied" error. Maybe i have to root the phone first?
Make a nandroid backup of all your partitions with TWRP, and it should include recovery img as well. Use fastboot boot twrp.img then do a nandroid backup.
However on some phones TWRP can't backup the recovery properly, and if that's the case then do the following:
Root your phone (Flash magisk or supersu, whatever works for you)
Reboot your phone to recovery.
Type adb shell su then dd if=/dev/block/mmcblk0p39 of=/sdcard/recovery.img
This will put recovery.img on your SD card.
I'm not sure if TWRP can properly backup recovery on your device, but trying both methods won't hurt.
How can I root my phone with Magisk without installing TWRP before?
I found the stock roms for my G4 here:
Codefire - Listing of H815
How can I find out which version (10C, 20D...) I need? The recovery is contained in the stocks roms, correct?
The recovery is usually contained in the stock ROM, downloading it to make sure won't hurt.
To find the device's model simply see your device manual.
Or if you remove your device's cover it should be written on the battery.
My device is a H815 with Android 7.0 and software version V29a-EUR-XX. In order to root the phone I would like to install an image file with a rom that is already rooted, but I couldn't find an image with my software version:
[ROOT] TMO/VZW/ATT/SPRINT/INTL Root your LG G4 with Low Effort Root!
Hello all, It's that time of the night where I post things on XDA and wake up to a bajillion PMs. Without further ado, I introduce "Low Effort Root". What is this? Low Effort Root is a root for your LG G4, named such because this is a root we...
forum.xda-developers.com
I could either install another H815 version (how risky is that?) or I could create an image of the rom on my device, root this image and then transfer it back on the phone.
pizza_alarm said:
My device is a H815 with Android 7.0 and software version V29a-EUR-XX. In order to root the phone I would like to install an image file with a rom that is already rooted, but I couldn't find an image with my software version:
[ROOT] TMO/VZW/ATT/SPRINT/INTL Root your LG G4 with Low Effort Root!
Hello all, It's that time of the night where I post things on XDA and wake up to a bajillion PMs. Without further ado, I introduce "Low Effort Root". What is this? Low Effort Root is a root for your LG G4, named such because this is a root we...
forum.xda-developers.com
I could either install another H815 version (how risky is that?) or I could create an image of the rom on my device, root this image and then transfer it back on the phone.
Click to expand...
Click to collapse
How about installing magisk manager on your phone then patching the boot.img through the app?
Installing a different version than your device can cause soft brick and that if you're lucky, so don't even think about it.
I installed Magisk Manager and followed method 2 in this guide:
How to Install Magisk and Root Android Devices with it [2 Methods]
In this comprehensive guide, we will show you how to install Magisk Universal Systemless Interface to root Android devices. There are two different methods to install it – First…
www.thecustomdroid.com
However, I don't know where I could find the correct stock boot image for my device. I can't extract it from my own device, because I need root permissions for that.
pizza_alarm said:
I installed Magisk Manager and followed method 2 in this guide:
How to Install Magisk and Root Android Devices with it [2 Methods]
In this comprehensive guide, we will show you how to install Magisk Universal Systemless Interface to root Android devices. There are two different methods to install it – First…
www.thecustomdroid.com
However, I don't know where I could find the correct stock boot image for my device. I can't extract it from my own device, because I need root permissions for that.
Click to expand...
Click to collapse
I'm sorry, but I can't help you with that :/
Keep searching I got those sites here, here, here and here. Just from typing "H815 stock rom" into google.
I don't know if they're official stock ROM nor if they're tampered with. So use them on your own risk.
Also those sites don't provide MD5 checksum to verify the integrity of the files so I wouldn't recommend them.
If you know someone with the same device from the same vendor in the same region as you then you may ask him to backup his stock ROM for you.
You can try asking a service center, I doubt they'll readily give you the ROM though.
If you absolutely need a custom ROM or root access for some reason, then get a device that has an active developing community. On a side note don't even think about Xiaomi devices. Maybe OnePlus or Pixel.
Goodluck.
I found the matching LG-H815_Official_v29A rom which contains the following files:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Is boot.bin the file which can be easily renamed as boot.img so that Idon't need any kind of extractor tool? In the case that the stock rom wasn't unlocked could the patched boot.img re-lock the phone?
pizza_alarm said:
I found the matching LG-H815_Official_v29A rom which contains the following files:
View attachment 5225263
Is boot.bin the file which can be easily renamed as boot.img so that Idon't need any kind of extractor tool? In the case that the stock rom wasn't unlocked could the patched boot.img re-lock the phone?
Click to expand...
Click to collapse
If you already found the stock ROM of your device then you don't need to root to backup your recovery.
I guess you failed to notice the recovery.bin file there haha. Don't be so tense when flashing the ROM friend relax a little and take a breath.
Now just make sure to flash the correct TWRP version of your device.
Goodluck.
First, as you might now, I am not liable if your phone would be bricked or damaged after this tutorial.
This method has worked perfectly for on my phone, which: OnePlus Nord N10 5G from Metro by T-Mobile. Build Number: 11.0.1.BE88CF. And it should work any rom stock
This tutorial is inspired by andreas__ from this topic. I recommend to take a quick glance before processing here.
General Info:
You need adb and fastboot installed and should know how to use it
You must do this process only once, afterwards you can follow the OTA survival steps
You need to factory hard reset the phone (very important)
Unlock the bootloader
If you are using locked metro by T-Mobile phone, make sure to request the "unlock token" in order to unlock the bootloader.
Google "How to Unlock Bootloader on OnePlus Phones | Unlocked and T-Mobile Variants" for the instructions
After you have unlocked the bootloader using this command:
Code:
fastboot oem unlock
The data will be wiped and it will do the factory reset
Create the boot image:
You need to pull out a clean boot image from your phone. I have used TWRP to do that
flash the latest twrp for this phone:
[TWRP][3.5.2_10][Billie]TWRP for Oneplus Nord N10 5G [BETA]
Use this command to flash it:
Code:
fastboot flash recovery Twrp_3.5.2-10_EduardoA3677-billie_OxygenOs11_Android11.img
boot the phone to twrp recovery, then head to:
Backup > select "Boot (96MB)" > Swipe to Backup
The boot image will be generated in the internal storage under the name "boot.emmc.win"
root and patch the image:
Restart the phone to the system, then download the latest magisk app
Make sure to allow "USB debugging" from the developer Options
Install and open the magisk app then tap on "install" (very top)
tap on "select and patch a file"
select "boot.emmc.win" which is the image that was generated by twrp
Magisk will patch it and place it in the download folder under the name "magisk_patched-23000_Obpf5.img"
Copy the patched image into ADB folder in your PC
flash the patched image:
Reboot the phone into bootloader mode
Then flash the patched image:
Code:
fastboot flash boot magisk_patched-23000_Obpf5.img
Reboot the phone into the system
Hurray! your phone now is officially rooted. You're welcome
I hope you find my instructions useful.
Reserved !!
hamooz92 said:
First, as you might now, I am not liable if your phone would be bricked or damaged after this tutorial.
This method has worked perfectly for on my phone, which: OnePlus Nord N10 5G from Metro by T-Mobile. Build Number: 11.0.1.BE88CF. And it should work any rom stock
This tutorial is inspired by andreas__ from this topic. I recommend to take a quick glance before processing here.
General Info:
You need adb and fastboot installed and should know how to use it
You must do this process only once, afterwards you can follow the OTA survival steps
You need to factory hard reset the phone (very important)
Unlock the bootloader
If you are using locked metro by T-Mobile phone, make sure to request the "unlock token" in order to unlock the bootloader.
Google "How to Unlock Bootloader on OnePlus Phones | Unlocked and T-Mobile Variants" for the instructions
After you have unlocked the bootloader using this command:
Code:
fastboot oem unlock
The data will be wiped and it will do the factory reset
Create the boot image:
You need to pull out a clean boot image from your phone. I have used TWRP to do that
flash the latest twrp for this phone:
[TWRP][3.5.2_10][Billie]TWRP for Oneplus Nord N10 5G [BETA]
Use this command to flash it:
Code:
fastboot flash recovery Twrp_3.5.2-10_EduardoA3677-billie_OxygenOs11_Android11.img
boot the phone to twrp recovery, then head to:
Backup > select "Boot (96MB)" > Swipe to Backup
The boot image will be generated in the internal storage under the name "boot.emmc.win"
root and patch the image:
Restart the phone to the system, then download the latest magisk app
Make sure to allow "USB debugging" from the developer Options
Install and open the magisk app then tap on "install" (very top)
tap on "select and patch a file"
select "boot.emmc.win" which is the image that was generated by twrp
Magisk will patch it and place it in the download folder under the name "magisk_patched-23000_Obpf5.img"
Copy the patched image into ADB folder in your PC
flash the patched image:
Reboot the phone into bootloader mode
Then flash the patched image:
Code:
fastboot flash boot magisk_patched-23000_Obpf5.img
Reboot the phone into the system
Hurray! your phone now is officially rooted. You're welcome
I hope you find my instructions useful.
Click to expand...
Click to collapse
Hate to tell you this but if using twrp just rename magisk apk to magisk zip and install zip it auto patches to the right slot for you and you just confirm the install via magisk in android
scottlam1 said:
Hate to tell you this but if using twrp just rename magisk apk to magisk zip and install zip it auto patches to the right slot for you and you just confirm the install via magisk in android
Click to expand...
Click to collapse
Exactly.
I lost root after the forced OTA on July 31/August 1. Today I followed this guide to install twrp, factory reset, then installed Magisk by renaming the APK and flashing within TWRP. However the SafetyNet check showed "Attestation Failed." I enabled MagiskHide and rebooted, and now pass SafetyNet.
Thank you for this very simple and useful guide. I was able to root with no loss of userdata, saving a lot of time that would otherwise go into creating a backup.
scottlam1 said:
Hate to tell you this but if using twrp just rename magisk apk to magisk zip and install zip it auto patches to the right slot for you and you just confirm the install via magisk in android
Click to expand...
Click to collapse
I don't understand
bgfal3 said:
I don't understand
Click to expand...
Click to collapse
They are saying rename magisk from apk to zip and flash it in TWRP
bgfal3 said:
I don't understand
Click to expand...
Click to collapse
Just rename the APK to .zip extention and install through zip installer in twrp
iam almost ready to root my device i have both zip files from adreas tutorial on how root it.
where those zips files need to be in order to flash it?
cmd can be used, sorry iam new to this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3lgato said:
View attachment 5485447
Click to expand...
Click to collapse
You need to get the unlock token first
Here is the instructions:
https://www.oneplus.com/support/answer/detail/op588
raginhomosapien said:
I lost root after the forced OTA on July 31/August 1. Today I followed this guide to install twrp, factory reset, then installed Magisk by renaming the APK and flashing within TWRP. However the SafetyNet check showed "Attestation Failed." I enabled MagiskHide and rebooted, and now pass SafetyNet.
Thank you for this very simple and useful guide. I was able to root with no loss of userdata, saving a lot of time that would otherwise go into creating a backup.
Click to expand...
Click to collapse
Glad it worked for you. You're welcome
Why it wait forever for attached device, even removing and reconnecting phone?
Rulesless said:
View attachment 5568509
Why it wait forever for attached device, even removing and reconnecting phone?
Click to expand...
Click to collapse
You have to be in fastboot mode before you can flash the recovery. Reboot into fastboot by typing "adb reboot fastboot" (without the quotes). Your phone should then reboot into fastboot mode. NOW, assuming you have already unlocked your bootloader, you can flash the recovery.
If anyone is still having the OEM unlocking greyed out issue, you need to do the device unlock from your phone, select request permanent unlocks then your device will reboot, from there you can then head back into dev options and you will be able to OEM unlock. Hope this helps seems not a lot of people realize this I hunted for the answer all over only to happen upon it when I was about to say forget it.
wcoolj said:
If anyone is still having the OEM unlocking greyed out issue, you need to do the device unlock from your phone, select request permanent unlocks then your device will reboot, from there you can then head back into dev options and you will be able to OEM unlock. Hope this helps seems not a lot of people realize this I hunted for the answer all over only to happen upon it when I was about to say forget it.
Click to expand...
Click to collapse
Just to add to this.....If you are unable to use device unlock because you have not met your carrier's requirements to do so yet you can use the script at this thread and it will open up oem unlock even if your phone is not eligible yet.
I have the N20. No twrp. Flashed a patched boot.img and lost radios. No wifi Bluetooth or sim)mobile data. Hoping that the platform is similar enough that someone could help me recover my device. Phone was sim locked, not sure if that's the issue. I forgot to run the command from the debloat script after flashing the unlock token, shouldn't have rushed this. I don't have a backup of anything though. Was trying to get root to back up everything. Factory resetting did nothing to fix the issue
PsYk0n4uT said:
Factory resetting did nothing to fix the issue
Click to expand...
Click to collapse
LOL never does at this level, just wipes cache and user partition, but nothing of value where we play- the assumption is you (or the bad guys) can't figure out how to write to the system, boot, etc partitions. (snicker).
So the good news is if you can find the EDL image, and follow the procedure to reflash the phone... it should restore everything for you.
(To be clear @PsYk0n4uT I linked you to the N10 EDL thread, not the N20...)
Thanks. So my issue so far. I don't think there is even a stock firmware posted anywhere. Though there is a backup of another device posted. How would I go about finding the EDL files for mine? Can one be created? Or would I need to source that from OnePlus or wait on someone to do that? I actually wasn't aware that I could boot the boot omg without flashing it to test it out first