I recently bought a MI 10T and it fell from my hand damaging the volume down button. The lock button heated up pretty quick so I switched it off and later it would go to fastboot mode when I try to switch it on. I tried to press all the buttons and it went to some Chinese update menu where I connected to WiFi for an update (thought it would might turn on the phone) but it showed error.
I couldn't afford to change the whole display panel as suggested by the Mi service centre so I took it to a local shop and after they repaired the button, the phone won't turn on and go into a reboot loop from mi recovery 3.0. I tried to wipe data but still it wouldn't help. I tried to reach out to a few local shops but they are trying to take advantage of the situation and taking money for doing nothing and declaring that the motherboard needs to be changed. What do I do? Can someone tell me what can be wrong with the device?
Related
Hi Guys,
I have my N7100 for almost 3 months now and yesterday my son accidentally spilled water on it. The whole unit did not get wet, just the side where the volume rocker is. And it switched off by itself. I removed the battery and let it dry for a few hours. I switched it on and yes it did turn on but one volume button ( - ) is not working and the back and menu keys are not working also and it does not recognize any touch on the screen but when I used the S-Pen it recognized it. It's a rooted, heavy customized and tweaked phone. I noticed that it went to "safe mode", it was indicated on the lower left side of the screen and all installed apps were gone. DPi value went into default. I tried to install some apps, it went successfully but I can not find it in the apps drawer. I went into recovery mode, hoping to remove it in safe mode (foolish me, did not even tried to read or search on xda for possible fix), re-flash a custom ROM but same thing. I also found that the two water damage indicators inside the phone turned pink. The components inside were dry when I opened it, but because I am eager to fix it I tried using a hair dryer to (of course) dry it a little bit without damaging anything. After a while I put everything all together, switched it on and it now recognized "touch". But issues with volume key ( - ) and menu&back buttons still remain and it is still in safe mode. I decided to restore it to factory default via recovery mode, I cleared everything, reformatted system, data, all menus with the word "reformat' I pressed them all. Restarted the phone and it just stays on the logo where it says "Samsung Galaxy Note II GT N7100". Tried to go back to recovery mode but with no avail. I tried to go to Download mode also, I was able to make it to the part where it says "press volume up to continue; press volume down to cancel" I then pressed volume up but nothing happens. I pressed the volume up and same thing. Tried to charge it while it is switched off, the battery icon charging appeared, it shows the circle animation but it does not animate and it doesn't animate also like it's charging itself. Plugged it into my laptop and it doesn't recognize it. I've been reading some XDA articles and I only came acrossed one possible way to resurrect it...To get Download Mode without 3-button combo using homemade JIG. Well, I know for a fact that I need to send this to Samsung Service center but I am still hoping that someone here might help me or I may still find other alternative solutions without spending a lot of $$$ in sending it for a repair. Thanks in advance!
Apparently u have formatted system partition. Have u try flash via PC odin? Maybe the download mode will work with odin
Yeah, that's what I thought also. Foolish me! Apparently I can't even try Odin since my laptop does not recognize the phone. I can't even go to the download mode. It was stuck on the part where it says Volume Up: Continue, Volume Down: Cancel.
hmm.. seems like the hard key for the volume are done for. since u already disassemble it, cant u use the manual way to press? it u able to go into download mode, the driver will auto download, well at least it auto download for me
Tried that also mate, but no luck. I think the phone does not recognize the volume rocker. I just noticed that when I pressed and hold the menu key plus the power button it goes to the page where it says volume up: continue...where you are supposed to press volume down+power+menu key right? I tried to press the volume up key to continue but no luck. I was browsing xda the whole day to search for an answer before I send this so Samsung service center. I tried a homemade jig so I can go to download mode but it does not work. I have read that other SGNII users were able to make it work. On the instructions it says to use 3pcs of 100K ohm and a 1k ohm resistors but I used 6pcs of 50k ohm + 1k resistors (since I can't find any 100k ohm resistor on any electronic store near my place) connected it to pin 4 and 5 of a micro usb plug and still no luck, nothing happens. Tried some several combinations.
I have don't have good sleep since my Note II died...Haven't eat properly...Yeah, you read it right...hahaha..Still trying to search for possible fixes, it's 12:40am now and I am almost sleepy, if I still can't find any solutions until tomorrow then I will be sending this to Samsung Service center
or....if Adam will reply on this thread http://forum.xda-developers.com/showthread.php?p=39387670 then I am willing to dismantle and do whatever he wants me to do just to resurrect the phone...
Can you go into recovery mode? If yes try adb reboot recovery or reboot to bootloader if you have twrp.
this is XXXDDDAAA
Like what I explained on the first post mate, Recovery and Download modes are not possible/can't access them...
red_hanks said:
Hi Guys,
I have my N7100 for almost 3 months now and yesterday my son accidentally spilled water on it. The whole unit did not get wet, just the side where the volume rocker is. And it switched off by itself. I removed the battery and let it dry for a few hours. I switched it on and yes it did turn on but one volume button ( - ) is not working and the back and menu keys are not working also and it does not recognize any touch on the screen but when I used the S-Pen it recognized it. It's a rooted, heavy customized and tweaked phone. I noticed that it went to "safe mode", it was indicated on the lower left side of the screen and all installed apps were gone. DPi value went into default. I tried to install some apps, it went successfully but I can not find it in the apps drawer. I went into recovery mode, hoping to remove it in safe mode (foolish me, did not even tried to read or search on xda for possible fix), re-flash a custom ROM but same thing. I also found that the two water damage indicators inside the phone turned pink. The components inside were dry when I opened it, but because I am eager to fix it I tried using a hair dryer to (of course) dry it a little bit without damaging anything. After a while I put everything all together, switched it on and it now recognized "touch". But issues with volume key ( - ) and menu&back buttons still remain and it is still in safe mode. I decided to restore it to factory default via recovery mode, I cleared everything, reformatted system, data, all menus with the word "reformat' I pressed them all. Restarted the phone and it just stays on the logo where it says "Samsung Galaxy Note II GT N7100". Tried to go back to recovery mode but with no avail. I tried to go to Download mode also, I was able to make it to the part where it says "press volume up to continue; press volume down to cancel" I then pressed volume up but nothing happens. I pressed the volume up and same thing. Tried to charge it while it is switched off, the battery icon charging appeared, it shows the circle animation but it does not animate and it doesn't animate also like it's charging itself. Plugged it into my laptop and it doesn't recognize it. I've been reading some XDA articles and I only came acrossed one possible way to resurrect it...To get Download Mode without 3-button combo using homemade JIG. Well, I know for a fact that I need to send this to Samsung Service center but I am still hoping that someone here might help me or I may still find other alternative solutions without spending a lot of $$$ in sending it for a repair. Thanks in advance!
Click to expand...
Click to collapse
the problem is because your volume rocker key and power button are shorted due to water content.. i recommend that you take it to a service center before something worse happens... dont turn on your phone again until its cleaned properly and dried.. take it to proper service ... else its very bad for your device.. coz it can get permanently dead
Yeah, that's what I am going to do today. I surrender can't find any solutions anymore. Will keep you guys posted. Thanks anyway!
It's with Samsung Service Center now. It's OOW and they were able to find out that it was rooted (of course!) I paid Php1,200 under the table (on one of the technicians) and now it's In-Warranty again hahaha, but I have to leave the phone for a couple of days or weeks since they need to replace some hardwares. I think that's the best thing I can do instead of paying more for an OOW repair. sad sad sad..weeks without my phone with me...going back to my old phones for the meantime...
Problems with my Samsung Galaxy Tab S 8.4 SM-T705:
1st: October 2014
2 weeks after buying, my tablet's battery drained overnight from 45% to zero. Next morning, I turned my tab on after charging to find out that the Tab starts but without any Samsung GAlaxy Tab S logo or Samsung Logo and the Screen has turned green, rendering it difficult to read in auto brightness mode or low brightness mode.
I restarted the device 2-3times and the device started working normally. This was my 1st device restart. I never used to power off the device before.
In 1st 6months, this greenish display problem n logo problem occured 2-3times, and i ignored it, because, it used to get resolved by itself with restart and I had no service centre in and around 50km to my work place.
2nd: January 2014
My device all of a sudden stopped working.. actually hanged.. I managed to turn it off but failed to restart it.
Later I realised that the device has restarted, but the screen was not responding when the screen blinked for a moment with the opening of book cover.. and the back cover of device was warm..
Googling taught me the way to access recovery screen n I opened recovery mode with "power+vol down+home key" and pressing vol down in recovery screen to restart tab.. again the tab started working fine..
3rd: Lollipop update: May 2015
I did Lollipop update. The device was smooth to operate at first. But gradually, i noticed that unlocking the tab failed to light up the display everytime, just the soft keys lighted up. But one day, the device freezed with no response from touch screen. I was unable to switch off the device also.. I had to drain the battery by playing music using S voice to turn the device off. "power+vol down+home key" too was not working.
On googling, I learned to reset device with "power+vol up+vol down" keys pressed together. finally the device restarted, but the device used to hang occassionally.
Googling let me know that i need to factory reset device upon firmware update for normal functioning, which i didn't do after update. so, I backed up my device, uninstalled many apps to make the device run a bit smooth and did a factory reset.. Resetting didn't improve the situation much, but now, the device display failed to light up on a regular basis on unlocking most of the time..
Now the situation is that, the device turns on, finger print scanner works, all apps n everything working, but display remains black, and touch screen is not responding.. using sidesync, everything on Tab can be accessed via laptop.
Tricks tried:
1) Factory reset
2) power+ vol up+vol down
3) power+ vol up+home key
4) power+ vol down + home key
5) Power off using sidesync and then restart
Results: All failure. Everything works but the display never lights up normally..
Plzz help....:crying::crying:
Bump. I'm starting to have similar problems with my SM-T800 running 5.0.2. I open the cover and the device fails to turn on. I press the power button and the screen stays black but the notification bar turns on. I can shake the crap out of the device and the screen stays black but I can see the notification bar flicker. Driving me batty.
If i had any problems like you guys, I would just return it to the place i bought it, for a refund or replacement or even a repair, post it to the service centre if it`s too far to travel too.
You problems sound like battery and or loose connector inside your tablet, it happens frequently on Samsung tablet for the connectors to come loose, if the tablet is dropped or twisted, no outside damage might be seen.
John.
I have a Samsung I9250 which I've unlocked, rooted and loaded with Lineage. The Lineage version is 13.0-20171126-NIGHTLY-maguro. The recovery is TWRP and the root is through SuperSU FREE (CM) v2.79-SR3. The On/Off button doesn't usually work. If the phone is off then pressing On/Off has no effect. Occasionally it works for no reason I can see, it seems to be random, but for the most part it simply doesn't have any effect. If the phone is on then the same is true. Turning it off from the On/Off button is usually impossible. I get round this through Settings>Display & lights>Wake on plug. This means I can activate the phone by connecting it to a PC using its USB cable. This will activate the phone immediately if it is off. It doesn't help with turning it off and I am usually reduced to taking the battery out. The phone is effectively useless although it is clearly NOT bricked. When I can turn it on it works fine.
I don't know if this is a hardware or software problem. If it's a software problem I don't know if the fault is in Lineage or TWRP or SuperSU. I noticed that the problem existed before I installed SuperSU. Has anyone else come across this problem? I'm reluctant to bin the phone because I spent such a long time getting Lineage on to it, but, if I can't turn it on or off it's not really a phone. Any help would be greatly appreciated.
@erich_vogt it's more a hardware problem, you can buy a new button (find link of online stores in accessories section or google.it).
for easyness you don't need to plug charge/usb everytime, you can set volume button waker, find in settings > button (don't remember where correctly, it will be somewhere there) then use volume switches to wake it.
erich_vogt said:
If the phone is off then pressing On/Off has no effect.
Click to expand...
Click to collapse
There have been power button bugs, but only in the OS. If it's not turning on from off, then I think the switch is broken! A common failure in old phones, which is why "volume button to wake" is important, to reduce load on the power button.
Thanks very much for offering to help.
I already had the option for the Volume control buttons to wake the phone turned on. It's here - Settings > Buttons > Volume Buttons > Wake up device. This worked for a while then stopped. I disassembled the phone to look at the On/Off button. I tried turning the phone on directly from the metal contact pad beneath the plastic button. This worked. When the phone had booted I checked to see if there was another nightly update for Lineage. There was the 3rd of Dec update. I downloaded and installed the nightly update using TWRP. It reported a successful install. The phone rebooted and never got past the Google boot-up screen. I waited for a few minutes and the took the battery out and tried turning on again from the metal contact pad. The phone booted but again got stuck (or seemed to) on the Google boot-up screen. I'm afraid that's it for me. This doesn't appear to be related to anything I have done or not done. The phone is just taking up too much time and it will have to go the the local recycler. Life is, as they say, too short. Thanks again for your suggestions.
erich_vogt said:
Thanks very much for offering to help.
I already had the option for the Volume control buttons to wake the phone turned on. It's here - Settings > Buttons > Volume Buttons > Wake up device. This worked for a while then stopped. I disassembled the phone to look at the On/Off button. I tried turning the phone on directly from the metal contact pad beneath the plastic button. This worked. When the phone had booted I checked to see if there was another nightly update for Lineage. There was the 3rd of Dec update. I downloaded and installed the nightly update using TWRP. It reported a successful install. The phone rebooted and never got past the Google boot-up screen. I waited for a few minutes and the took the battery out and tried turning on again from the metal contact pad. The phone booted but again got stuck (or seemed to) on the Google boot-up screen. I'm afraid that's it for me. This doesn't appear to be related to anything I have done or not done. The phone is just taking up too much time and it will have to go the the local recycler. Life is, as they say, too short. Thanks again for your suggestions.
Click to expand...
Click to collapse
3rd dec nightly has problem with booting, get back to older than it.
Reset volume button waker, if it stopped working. I never had problems with volume buttons.
I'd second the idea of it being software. I've had problems with all builds after 20171112. I get the impression there was something overlooked when the developers unified the builds for different GNex variants.
If you still have the phone, try that 20171112 build.
I don't know how to roll back to an earlier build. The phone will not boot. If I try VolumeDown+On/Off to try to get into TWRP Recovery mode nothing happens. The adb bridge option is turned on but if I connect the phone to my PC with a usb cable it does not appear in Device Manager as it used to. If I run ".\adb devices" it is not listed so clearly adb cannot find it. I don't know what else I can do.
erich_vogt said:
The phone will not boot. If I try VolumeDown+On/Off to try to get into TWRP Recovery mode nothing happens. The adb bridge option is turned on but if I connect the phone to my PC with a usb cable it does not appear in Device Manager as it used to. If I run ".\adb devices" it is not listed so clearly adb cannot find it. I don't know what else I can do.
Click to expand...
Click to collapse
Ah, ok. Sorry, I thought you could still do more than that, but it was rebooting and unusable in that sense.
That's well beyond any help I can offer you. I hope you got any data off it.
I bought a mi9 if new (128gb blue). I was about 10 minutes with him on. I managed to turn it on, but decided to reset the factory mode to donate it to someone else.
After resetting the phone no longer works.
Nothing happens when i press the power button with or without volume buttons. Even if I connect the charger, the phone does not show anything. It is completely dead.
I'm from brazil
So i bought my mi 10t lite and immediately after i open it and started setting it up i noticed that my power button get stuck when i press it from one side and my phone shutdown,if i pressed again it got unstuck,it is super annoying.Does someone have the same problem ?
No. I dont face that problem