G985F stuck in Download Mode with many problems... :/ - Samsung Galaxy S20 / S20+ / S20 Ultra Questions &

Hi everybody,
I'm stuck in a pretty damn mess here. I have an Galaxy S20+ G985F device which is stuck in Download Mode with no ROM installed, a locked bootloader, and a changed recovery and vbmeta (one that came with a working TWRP image) image flashed. :/
Is thee any way to get out of this situation of which I don't know how exactly the phone got there? Seems like a mistakenly locked boot loader by long pressing the Vol Up button once in the Booloader Lock/Unlock menu.
When trying to flash with heimall the phone says, ie.:
Custom Binary (VBMETA) Blocked By OEM Lock
Any chance on recovering the device? There should actually no ROM be installed at the moment. Cannot boot anything, the device always goes into Download mode only showing an entry for "Vol Down + Side Key for 7 seconds: Cancel (restart phone)" which results in the device going to the screen again...
Flashing with "odin4" on Linux says:
odin4 -b BL_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5 -a AP_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT_meta_OS10.tar.md5 -c CP_G985FXXU1ATCT_CP15511927_CL18335124_QB30141694_REV01_user_low_ship_MULTI_CERT.tar.md5 -s CSC_OMC_OXM_G985FOXM1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5
Check file : BL_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5
Check file : AP_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT_meta_OS10.tar.md5
Check file : CP_G985FXXU1ATCT_CP15511927_CL18335124_QB30141694_REV01_user_low_ship_MULTI_CERT.tar.md5
Check file : CSC_OMC_OXM_G985FOXM1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5
/dev/bus/usb/001/054
/dev/bus/usb/001/054
Setup Connection
Set Partition
Receive PIT Info
success getpit
Upload Binaries
Binary arrange fail. Binary is invalid
Fail uploadBinaries
Kind regards and thanks for any help,
Marc

try with samsung smart switch with emergency software recovery

kosique said:
Hi everybody,
I'm stuck in a pretty damn mess here. I have an Galaxy S20+ G985F device which is stuck in Download Mode with no ROM installed, a locked bootloader, and a changed recovery and vbmeta (one that came with a working TWRP image) image flashed. :/
Is thee any way to get out of this situation of which I don't know how exactly the phone got there? Seems like a mistakenly locked boot loader by long pressing the Vol Up button once in the Booloader Lock/Unlock menu.
When trying to flash with heimall the phone says, ie.:
Custom Binary (VBMETA) Blocked By OEM Lock
Any chance on recovering the device? There should actually no ROM be installed at the moment. Cannot boot anything, the device always goes into Download mode only showing an entry for "Vol Down + Side Key for 7 seconds: Cancel (restart phone)" which results in the device going to the screen again...
Flashing with "odin4" on Linux says:
odin4 -b BL_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5 -a AP_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT_meta_OS10.tar.md5 -c CP_G985FXXU1ATCT_CP15511927_CL18335124_QB30141694_REV01_user_low_ship_MULTI_CERT.tar.md5 -s CSC_OMC_OXM_G985FOXM1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5
Check file : BL_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5
Check file : AP_G985FXXU1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT_meta_OS10.tar.md5
Check file : CP_G985FXXU1ATCT_CP15511927_CL18335124_QB30141694_REV01_user_low_ship_MULTI_CERT.tar.md5
Check file : CSC_OMC_OXM_G985FOXM1ATD3_CL18335124_QB30559577_REV01_user_low_ship_MULTI_CERT.tar.md5
/dev/bus/usb/001/054
/dev/bus/usb/001/054
Setup Connection
Set Partition
Receive PIT Info
success getpit
Upload Binaries
Binary arrange fail. Binary is invalid
Fail uploadBinaries
Kind regards and thanks for any help,
Marc
Click to expand...
Click to collapse
And also you cannot turn off your phone? )
Prepare a recovery tar file with vbmeta and recovery in it. Flash with odin and reboot. Then disable encription.
Then redo the initial process of flashing tar file with or without the rest of the rom files.
If ur alao flashing rom files put your recovery tar file to others section in odin.

Related

ERROR MODE Attention! Please update system again.

Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!!
Mohammadreza76646 said:
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!!
Click to expand...
Click to collapse
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it's flashed to.
Also
With multi tool , make sure you put check mark on emui 8. Up in upper right corner. That way it uses Oreo partition names and file not nougat.
The partition length over message usually means nougat file or partition name used on Oreo system
mrmazak said:
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it's flashed to.
Also
With multi tool , make sure you put check mark on emui 8. Up in upper right corner. That way it uses Oreo partition names and file not nougat.
The partition length over message usually means nougat file or partition name used on Oreo system
Click to expand...
Click to collapse
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error...)!
And unfortunately my TWRP dos not work anymore
Mohammadreza76646 said:
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error...)!
And unfortunately my TWRP dos not work anymore
Click to expand...
Click to collapse
I give my phone to a friend to work on it. If he can't fix it I try new multi tools version to flash phone.
Mohammadreza76646 said:
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error...)!
And unfortunately my TWRP dos not work anymore
Click to expand...
Click to collapse
On the extractor app. On options tab uncheck the verify header option, it should extract then.
Then perhaps first do these three partitions.
Kernel.img
Ramdisk.img
Then
twrp_ramdisk or for stock use recovery_ramdisk
Mohammadreza76646 said:
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!!
Click to expand...
Click to collapse
I ever have similiar problem with you dude, but it's solved now, if you always stuck on " its OK but when my phone want to start its stuck on google page "just a sec...", its call google accont verification, i'll by bypass with this script, save as to .bat and put on adb folder
adb devices
adb shell content insert --uri content://settings/secure --bind name:s:user_setup_complete --bind value:s:1
adb shell am start -n com.google.android.gsf.login/
adb shell am start -n com.google.android.gsf.login.LoginActivity
pause
in fastboot type:
fastboot -w
after all it's works to me to bypass google account verification
and if now your problem is
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
i solve with re-flash system from this
https://androidfilehost.com/?fid=673956719939830152
fastboot flash system system.img
and doing TWRP Flashing
https://forum.xda-developers.com/devdb/project/?id=25826#downloads
fastboot flash recovery_ramdisk complete_twrp_ramdisk.img
and voila my problem solved..
mrmazak said:
On the extractor app. On options tab uncheck the verify header option, it should extract then.
Then perhaps first do these three partitions.
Kernel.img
Ramdisk.img
Then
twrp_ramdisk or for stock use recovery_ramdisk
Click to expand...
Click to collapse
Hello again dude.
Finally I flashed my phone and I got the system installed.
But now my phones IMEI is lost. and I cant put sim on it!!!
what should I do now???
FRP is locked! (
Mohammadreza76646 said:
Hello again dude.
Finally I flashed my phone and I got the system installed.
But now my phones IMEI is lost. and I cant put sim on it!!!
what should I do now???
FRP is locked! (
Click to expand...
Click to collapse
So now is locked frp. Does phone have twrp or stock now.?
I think when you tried to install the oreo update for second time, you followed same tutorial as the first time. And that made you problem worse. The tutorial has you flash no-check recovery to 2 partition by block number. 22 & 29. On nougat that is "recovery" and "recovery2". On Oreo partion table it is "reserved2" & "erecovery_vendor"
I don't know how to fix imei. Have hope that if to ucan have a full ota install , maybe can be fixed.
There is available a "service rom" (used to fix most all problem) for Europe region with l21.
I can share link to site with service rom if you want , but I have not used it myself so not gonna be much help with it.
Link is to rusian language page. Google should translate for you.
https://4pda.ru/forum/index.php?showtopic=879524&view=findpost&p=73818595
mrmazak said:
So now is locked frp. Does phone have twrp or stock now.?
I think when you tried to install the oreo update for second time, you followed same tutorial as the first time. And that made you problem worse. The tutorial has you flash no-check recovery to 2 partition by block number. 22 & 29. On nougat that is "recovery" and "recovery2". On Oreo partion table it is "reserved2" & "erecovery_vendor"
I don't know how to fix imei. Have hope that if to ucan have a full ota install , maybe can be fixed.
There is available a "service rom" (used to fix most all problem) for Europe region with l21.
I can share link to site with service rom if you want , but I have not used it myself so not gonna be much help with it.
Link is to rusian language page. Google should translate for you.
https://4pda.ru/forum/index.php?showtopic=879524&view=findpost&p=73818595
Click to expand...
Click to collapse
It have stock recovery.
Mohammadreza76646 said:
It have stock recovery.
Click to expand...
Click to collapse
in summery. because i have been going back and forth in multiple different groups, multiple problem, i cant remember it all.
you have broken system, from failed root attempt, followed by failed update.
device condition is as follows.
--system not booting
--stock recovery loads
--fastboot/bootloader loads, but is in frp lock status
options are limited, at best.
I think "dload" method with service rom is best.
other option is maybe paid service like dc-unlock. But I can recall some note on there service about frp-unlock, that can only be used on device with working system. (of course if was working system, wouldn't need dc-unlock)
mrmazak said:
in summery. because i have been going back and forth in multiple different groups, multiple problem, i cant remember it all.
you have broken system, from failed root attempt, followed by failed update.
device condition is as follows.
--system not booting
--stock recovery loads
--fastboot/bootloader loads, but is in frp lock status
options are limited, at best.
I think "dload" method with service rom is best.
other option is maybe paid service like dc-unlock. But I can recall some note on there service about frp-unlock, that can only be used on device with working system. (of course if was working system, wouldn't need dc-unlock)
Click to expand...
Click to collapse
No. System boot successfully!
I will send you screenshot:
Mohammadreza76646 said:
No. System boot successfully!
I will send you screenshot:
Click to expand...
Click to collapse
here you are
Mohammadreza76646 said:
here you are
Click to expand...
Click to collapse
what about the "about phone" screen
what does it show for version?
If is all stock you should be able to go into deveolper options and enable "oem unlock". If it is greyed out and cannot switch it. Try First to remove google account (all accounts ). and reboot. See if can change then. If not, try Second to do "fastboot oem relock [enter your bootloader code here]
after relock and rebooted oem switch should be enabled again.
****RELOCK IS ONLY ADVISED IF 100% STOCK ROM****
otherwise relock could make more trouble.
Still not sure how to get IMEI back even if unlocked frp though.
**And please stop posting in other threads , the same problem , because you are getting help here.
your post in recovery thread is off topic to that thread and just makes the forum harder to maintain.
mrmazak said:
what about the "about phone" screen
what does it show for version?
If is all stock you should be able to go into deveolper options and enable "oem unlock". If it is greyed out and cannot switch it. Try First to remove google account (all accounts ). and reboot. See if can change then. If not, try Second to do "fastboot oem relock [enter your bootloader code here]
after relock and rebooted oem switch should be enabled again.
****RELOCK IS ONLY ADVISED IF 100% STOCK ROM****
otherwise relock could make more trouble.
Still not sure how to get IMEI back even if unlocked frp though.
**And please stop posting in other threads , the same problem , because you are getting help here.
your post in recovery thread is off topic to that thread and just makes the forum harder to maintain.
Click to expand...
Click to collapse
Thanks )
I'm so sorry for my posts, it's because I don't have a stable connection and I can't see notification of my thread.
I gave my phone to friend an he fix IMEI (I don't know how)
But OEM is steel lock.
I think he did it with using special box.
Mohammadreza76646 said:
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!![/QUOTE
Are u able.to boot into twrp ?
Click to expand...
Click to collapse
Hello I have a Huawei Mate-SE (with bootloader unlocked and rooted with magisk v16). I have been using the android custom rom RRO v6 (RR-O-v6.0.0-20180401-bnd-OpenKirin) for around a month now. I got this exact same problem about the White Screen saying "ERROR MODE Attention...." since I updated the Magisk to latest version (from the installed application) and rebooted my phone. SInce I rebooted I am getting that same error which makes the phone loops into it for a few times and then it loads the Huawei eRecovery that offers me some options that I am not sure what would do to my phone.
I have been trying to connect to adb tools/fastboot but it doesn't detect the phone and im pretty sure I have the device drivers installed on my computer since nothing have changed in my pc for a month now since I flashed RRO on it.
Is there any other mode besides recovery that would allow me to connect adb/fastboot to it? Or does anyone knows how should I proceed?
IonDEfeso said:
Hello I have a Huawei Mate-SE (with bootloader unlocked and rooted with magisk v16). I have been using the android custom rom RRO v6 (RR-O-v6.0.0-20180401-bnd-OpenKirin) for around a month now. I got this exact same problem about the White Screen saying "ERROR MODE Attention...." since I updated the Magisk to latest version (from the installed application) and rebooted my phone. SInce I rebooted I am getting that same error which makes the phone loops into it for a few times and then it loads the Huawei eRecovery that offers me some options that I am not sure what would do to my phone.
I have been trying to connect to adb tools/fastboot but it doesn't detect the phone and im pretty sure I have the device drivers installed on my computer since nothing have changed in my pc for a month now since I flashed RRO on it.
Is there any other mode besides recovery that would allow me to connect adb/fastboot to it? Or does anyone knows how should I proceed?
Click to expand...
Click to collapse
I have seen where the magisk update screwed up and patches the kernel intead of the ramdisk.
Power off , long press power button.
Hold volume down and plug in USB from PC.
This should cause it to boot into fastboot mode.
Then flash the stock kernel. And the stock or first patched ramdisk. (From earlier root)
mrmazak said:
I have seen where the magisk update screwed up and patches the kernel intead of the ramdisk.
Power off , long press power button.
Hold volume down and plug in USB from PC.
This should cause it to boot into fastboot mode.
Then flash the stock kernel. And the stock or first patched ramdisk. (From earlier root)
Click to expand...
Click to collapse
Hi thank you I was able to finally detect the device now. I am unsure about the kernel is that the recovery.img or system.img files I downloaded (i saved every file i used when I installed the rom) or do I need to look for the kernel somewhere else? I do have the complete_twrp_ramdisk.img file though.
Edit, I did more research and found the stock kernel is withing the boot.img file which I dont have so I looked up for the official BND-L34 oreo update and im currently downloading to extract the stock boot.img from the update.zip and flash it. Since that download was going to take me a while anyway i tried flashing the twrp recovery file without success (didn't changed anything) so i guess I should follow the instructions you gave me by flashing the kernel first then the twrp recovery.
mrmazak said:
I have seen where the magisk update screwed up and patches the kernel intead of the ramdisk.
Power off , long press power button.
Hold volume down and plug in USB from PC.
This should cause it to boot into fastboot mode.
Then flash the stock kernel. And the stock or first patched ramdisk. (From earlier root)
Click to expand...
Click to collapse
Do you know what the boot.img files name is after extraction?
I have extracted all 3 update zips and cannot find anything called boot.img
By the way, thank you.. After updating magisk I have been dealing with failed recovery and failed boot for over a week and this is the first reply anywhere that looks promising
IonDEfeso said:
Hi thank you I was able to finally detect the device now. I am unsure about the kernel is that the recovery.img or system.img files I downloaded (i saved every file i used when I installed the rom) or do I need to look for the kernel somewhere else? I do have the complete_twrp_ramdisk.img file though.
Edit, I did more research and found the stock kernel is withing the boot.img file which I dont have so I looked up for the official BND-L34 oreo update and im currently downloading to extract the stock boot.img from the update.zip and flash it. Since that download was going to take me a while anyway i tried flashing the twrp recovery file without success (didn't changed anything) so i guess I should follow the instructions you gave me by flashing the kernel first then the twrp recovery.
Click to expand...
Click to collapse
if you were on oreo. then there is not a boot.img, instaed there is seperate ramdisk.img and kernel.img.
i have all the files already extracted for oreo and a backup from nougat as well.
https://androidfilehost.com/?w=files&flid=265998
make sure you know what you are doing before flashing.
for example. on oreo the boot and recovery share one kernel image. SO if kernel is messed up you will not be able to boot "boot" or "recovery"

[Guide/Magisk] Root for the Galaxy A10 Series & Flash TWRP (Unlocked Exynos only, A10s not supported)

How to Flash TWRP & Root Samsung Galaxy A10 series (Unlocked Exynos Only, A10s (A107F/M) not supported)
NOTICE :
Before you move further, make clear that rooting device -
- Your warranty will be void
- Some of functions may not work on rooted device, some function may get back with un rooting, some may never.
- All your data on device will be lost
- Flashing custom binaries may brick (Usually soft but can be hard brick too) your device, so follow it on your own risk!
If you are ready with condition, move further -
Click to expand...
Click to collapse
Before moving to root device, must read every single instruction given below as any small mistake can lead to fail to achieve root or may brick the device.
A. Unlocking Bootloader
This is a basic step to root device. Go to settings - about phone - Software Information - tap multiple times on "Build number" - This will open developer option.
Now in settings at the end, you will have new option "Developer options" - look for OEM unlocking - Enable it.
(PS : If you don't see this option then you may need to wait up to 7 days or more to appear or may be on some operator you will get it never. Without this option you can not root your device, sorry!).
How to get OEM Unlock option back?
1. Open the Settings app. Tap on General Management → Date and time.
2. Use the toggle button to disable Automatic date and time.
3. Set date option will be enabled now. Tap on it, and set the date to about 10-20 days earlier.
4. Enable developer options.
4.a Go to your device Settings.
4.b Select ‘About phone’ » tap seven times on ‘Build number’.
└ This will enable Developer options under Settings.
4.c Go back to Settings » scroll down to the bottom and you’ll see Developer options menu.
5. Open developer options (in the Settings app itself), and find the option called ‘Auto update system‘. Use the toggle button to disable it.
6. Now, go back to the main screen of Setting, and then tap on Software update.
7. Disable the option ‘Download updates automatically‘.
8. Tap on ‘Download updates manually‘ option, but it will give you an error because of the wrong date, so it’s fine.
9. Restart the device.
10. Go to Settings > Developer options. The OEM unlock option should be enabled now.
Once you have enable OEM unlock option, switch off your device and reboot to download mode.
To put device in download mode - Press Volume Up & then Press Volume Down (Keep holding both) and connect device to PC with USB cable
When device start to download mode, long press volume up to unlock the bootloader. This will wipe your data and automatically reboot
Now let finish setup and again enable developer options (as said above), and confirm that the OEM unlocking option exists and grayed out!
If it is not then you can not root device!
Once you see this option and greyed out, you are ready to flash custom binary and root your device.2. setup the phone by skipping the wizard.
B. Disabling Android Verified Boot
1. Reboot to DOWNLOAD mode.
2. Download Odin 3.14.4 or newer and make sure Samsung USB drivers are installed.
3. Open Odin and put the vbmeta_disabled.tar into USERDATA slot and click "Start"
4. Your device will reboot but it will not boot into system as vbmeta signature has changed.
5. Your device will reboot into RECOVERY mode automatically and prompt "You have to reset your device to factory settings". Use "Volume Up" or "Volume Down" button to move and "Power" button to select. Confirm and reset the device to factory settings.
6. This is the last time the data on the device has to be cleared. Afterwards, if you don't re-lock bootloader or re-enable the Android Verified Boot, you will not lose your data. Be aware, a stock firmware package contains a Android Verified Boot Metadata Image (vbmeta.img) with verifications enabled. You will need to flash the vbmeta_disable image (put into USERDATA slot) along with the stock firmware (use BL, AP, CP, CSC slots) to make sure AVB is not re-enabled and the data is preserved.
C. Flashing TWRP/Magisk
link
Important :
Due to the fact that some devices no longer uses ramdisk in boot images, Magisk has no choice but to be installed in the recovery partition. For these devices, you will have to boot to recovery every time if you want Magisk. Since both Magisk and recovery lives in the same partition, what you actually end up getting when you choose to boot to recovery will be determined by how long you press volume up.
(Powering up normally) → (System with NO Magisk)
(OEM Recovery Key Combo) → (Splash screen) → (Release all buttons) → (System with Magisk)
(OEM Recovery Key Combo) → (Splash screen) → (Keep pressing volume up) → (Actual recovery)
Thanks and credit
For more details read Installation guide by @topjohnwu from Here.
All credit and thanks go to @topjohnwu for magisk & guide.
@dr.ketan for this guide from Here
@jesec for rooting guide Here
@ianmacd for multidisabler from here
Me
reserved.
Hi
Thanks for putting out the details guide!
I followed the steps carefully but got stuck at step 12 - the device boots to download mode and says: "error verifying vbmeta image..."
Luckily I was able to flash it back to stock - but the magisk_patched.tar looks faulty (I copied it using adb) so no root for me
Any ideas?
dani3ltony said:
Hi
Thanks for putting out the details guide!
I followed the steps carefully but got stuck at step 12 - the device boots to download mode and says: "error verifying vbmeta image..."
Luckily I was able to flash it back to stock - but the magisk_patched.tar looks faulty (I copied it using adb) so no root for me
Any ideas?
Click to expand...
Click to collapse
Unplug USB and replug it then make sure the size of tar file almost the same as origin.
for step 6, can we transfer the file via SD card?
afaneh92 said:
Unplug USB and replug it then make sure the size of tar file almost the same as origin.
Click to expand...
Click to collapse
Hi
I triple did it, but no luck
s_ryan said:
for step 6, can we transfer the file via SD card?
Click to expand...
Click to collapse
Sure.
dani3ltony said:
Hi
I triple did it, but no luck
Click to expand...
Click to collapse
Flash AP file only for some reason the BL tar include vbmeta.img but you can patch it too.
I also hit the same problem that soft-brick my phone.. just to confirm, the AP.md5 file u said to use, its name is this? AP_A105GDXU2ASE3_CL15918313_QB23932289_REV00_user_low_ship_meta_OS9.tar
afaneh92 said:
Sure.
Flash AP file only for some reason the BL tar include vbmeta.img but you can patch it too.
Click to expand...
Click to collapse
s_ryan said:
I also hit the same problem that soft-brick my phone.. just to confirm, the AP.md5 file u said to use, its name is this? AP_A105GDXU2ASE3_CL15918313_QB23932289_REV00_user_low_ship_meta_OS9.tar
Click to expand...
Click to collapse
yes
will try to make patched tar for all bootloaders when I got some free time.
Guide updated with more details
Hey dude,
Thanks for the update, I have a problem with step 7
7) Open Magisk Manager - Magisk (first one) - Install - select to "Select and Patch file" - Navigate file you have copied to device (BL_[device_model_sw_ver].tar.md5).
I followed but magisk says No Boot image found, process error, installation failed
afaneh92 said:
Guide updated with more details
Click to expand...
Click to collapse
s_ryan said:
Hey dude,
Thanks for the update, I have a problem with step 7
7) Open Magisk Manager - Magisk (first one) - Install - select to "Select and Patch file" - Navigate file you have copied to device (BL_[device_model_sw_ver].tar.md5).
I followed but magisk says No Boot image found, process error, installation failed
Click to expand...
Click to collapse
My bad I didnt test this, the BL file contain vbmeta.img and need to be patched. Will try to find better solution.
You can flash stock BL file only then reboot again to bootloader and flash the rest files.
I see.. no worries.. I tried to flash the patched ap file with the stock bl, it soft brinked my phone the last time I did it.. anyway, I will wait for your workaround..
Appreciate your help!
s_ryan said:
I see.. no worries.. I tried to flash the patched ap file with the stock bl, it soft brinked my phone the last time I did it.. anyway, I will wait for your workaround..
Appreciate your help!
Click to expand...
Click to collapse
Can you replace vbmeta.img from patched AP with BL using 7zip.
remove md5 extension from BL file.
Guide updated and added flash TWRP instructions
afaneh92 said:
2.Download A10_multidisabler-*-1.41.zip from here and copy to Ext Storage (Because once you flash TWRP, Int storage will not be readable)
Click to expand...
Click to collapse
I think it would be helpful to users if there were a single multi-disabler for all Samsung devices. To that end, I've incorporated your changes for the A10 into my multidisabler and attached a test version to this posting.
Will you please test it? If it works for you, I'll issue a new release.
ianmacd said:
I think it would be helpful to users if there were a single multi-disabler for all Samsung devices. To that end, I've incorporated your changes for the A10 into my multidisabler and attached a test version to this posting.
Will you please test it? If it works for you, I'll issue a new release.
Click to expand...
Click to collapse
Thanks for the update, I was thinking to make pull request with changes. After make sure every thing is working as it should.
afaneh92 said:
Thanks for the update, I was thinking to make pull request with changes. After make sure every thing is working as it should.
Click to expand...
Click to collapse
Thanks. In your case, it's easier now if you just verify that the script I attached is working, since I've already integrated the changes you made in your clone.
Anyone who wants multidisabler support for a new device, however, can either send me a pull request against the latest code, or run the following script on a live, rooted device:
Code:
#!/bin/sh
getprop ro.boot.bootloader
echo --
ls -l /vendor/etc/init/pa_daemon*.rc /vendor/etc/fstab.exynos*
echo --
cat /vendor/etc/fstab.exynos*
echo --
su -c cat /init.rc
Hi dude..
I tried it.. unfortunately I still have problems.. here are some of the problems
1) my 7zip does not allow me to mod the BL files within the md5 extension, so I extracted them out and replaced the file manually then zip it to Tar.. (the VBmeta file is only 1kb) is that right?
2) after flashing via odin, I did a reboot, I encountered a VBMEta error, "Error verifying vbmeta image" Verification_disabled bit is (cant see it, block by the camera module)
In the end, i restored the firmware and got everything back.
s_ryan said:
Hi dude..
I tried it.. unfortunately I still have problems.. here are some of the problems
1) my 7zip does not allow me to mod the BL files within the md5 extension, so I extracted them out and replaced the file manually then zip it to Tar.. (the VBmeta file is only 1kb) is that right?
2) after flashing via odin, I did a reboot, I encountered a VBMEta error, "Error verifying vbmeta image" Verification_disabled bit is (cant see it, block by the camera module)
In the end, i restored the firmware and got everything back.
Click to expand...
Click to collapse
Try using this vbmeta.img (inside the tar file). It worked for me on the A20 with similar error. This file normally seems to be a checksum checker and if it doesn't match what the phone wants to see it gives you that error. But this file was modified to essentially be blank so there is nothing to give the phone an error.

How to Root Your Samsung Galaxy A10 + Install Twrp

READ EVERYTHING CAREFULLY!
1.Your phone warranty will be void after this tutorial!
2.Any small mistake and your phone is bricked/bootlooped!
3.All of your data will be lost so back it up somewhere
Click to expand...
Click to collapse
(Fixed the tutorial my bad.)
Click to expand...
Click to collapse
Hey Guys Im Back! Thank you for the support and how it blew up. I have tested this on Android 10 UI 2.0 and it works better then ever!
Also installed lineage os : https://forum.xda-developers.com/galaxy-a10/development/rom-lineage-os-a10-a105f-t4078093
So i tried using afaneh92's tutorial which will be linked here : https://forum.xda-developers.com/galaxy-a10/how-to/magisk-root-galaxy-a10-series-t3963822
Which lead to me bootlooping or softbricking and my storage was reduced from 32 gb to 16Gb so i decided to work on my own method!
Credits go to afaneh92 for the Twrp!
BEFORE YOU START YOU SHOULD HAVE
1.Samsung Drivers installed
2.Odin Installed
3.7zip Installed
4.A data transfer cable
5.A Proper working brain
If you have all of those lets start!
A: Phone settings
1.Go in settings>about phone>software information>build number tap that 5 times until it says "You are a developer now" then you will have Developer options unlocked
2.Then go in developer functions and find OEM unlocking tick that on scroll down until you see Usb Debugging and tick that also Disable Auto Updates option
B: Download TWRP and 2 other important files
1.Dial *#1234# and it will show the AP and some others, focus on AP paste it on google and get the download for it
2.After downloaded move the AP to your download folder in your android device
3.You will get a magisk_patched.tar after its been offically converted
4.Get the twrp for a10
Download the twrp file here : https://mega.nz/#!OU1WhSDZ!vQz5K1wpqBhg0hCD59aziaHPxFlUsT_2WG8SgT8p6iY
5.After you got everything open the .tar archive and extract vbmeta.img, boot.img and you should already have recovery.img on your Desktop
6.Grab all the 3 .img files and archive them into a .tar using 7zip, Now continue to step C,
C :Unlocking The Bootloader and Getting Into Download Mode (THE PART WHERE YOU RESET YOUR PHONE)
1.Turn Off your phone
1.2.Put your data cable into your PC(dont connect your phone to it yet)
1.3.Hold Volume Up and Down then insert the cable into your phone
1.4.When you see a bluescreen let go
1.5.Hold vol up until you see another screen then let go for 1 second and hold vol up again
2.Your device will reset itself and reboot
2.1.After the device has booted in into the setup take the cable out after Turn off your phone
2.2.Hold Vol Up and Down again and connect the cable
2.3.Let go when a blue screen appears then press vol up until you are in download mode
D: Flashing TWRP
1.Open Odin
2.Press on AP then find Desktop.tar and press open
3.Press start and let it do its thing
4.After your Phone has rebooted you oficially have TWRP installed
5.If you want to know hoe to root go to step E
E: Installing Magisk
Since magisk is counted as the best rooting option rn i will be using it in this tutorial(Sorry supersu fans)
1.Install Magisk Manager
2.Press on Install (first one) then press install again and after that press Install Zip Only
3.Then go into Twrp by doing the steps below
3.1.Turn off your device
3.2.Hold vol up and power button untill you see TWRP logo
4.Press install
4.1.Find magisk-v20.4(20400).zip
4.2Swipe right on the bottom to flash it then press reboot system now.
5.Now you have TWRP,Root and Magisk Congratulations!
What happens if something goes wrong.
1.SV Error Device 1 library 0 - You installed the wrong firmware look for the right firmware.To check go in recovery mode and look at the A105XXXXXX and then look for a download. Remider AP->AP BL->BL CP->CP HOME_CSC->CSC
2.vbmeta.img error - you have the wrong vbmeta.img file. Redownload the original firmware and take out the right vbmeta.img next time you try flashing. Reminder AP->AP BL->BL CP->CP HOME_CSC->CSC
3.A blue screen telling you to use samsung switch emergency update. That wont work so just flash the original firmware and try flashing twrp again.
4.When i try to boot in it gets me into TWRP - Thats just because that your data is corrupted and to fix it while in TWRP mode press wipe then swipe after its done press Reboot To System. That should be a fix
5.My internal storage is just full of weird numbers and I can't download anything on it! Go in TWRP then wipe,press advanced wipe, click on internal storage and data, swipe. That should fix the error
6.Boootlooping or Bricked! Installed corrupted firmware or the recovery was f-ed up. Then install the right firmware and redo the steps!
If you have issues during the process send it in the comment ill try to respond as fast as i can!
i notice thread title says exynos only.. u do know they are all exynos including a102u and a102u1 right?
Oh. Alright thanks for telling me.
Press on app? I have nothing in odin saying that, do you mean ap?
Edit: guess not....i'm bricked, stuck on galaxy logo, device not recognized by pc, holoding power button wont force reboot, nothing lol.
Edit2: can force reboot holding volume down and power but instantly stuck on logo again, cannot power off or enter download, nothing...bricked. Followed this guide to the letter. I assumed when you said app in odin you meant ap since there is no app button. My bootloader unlocked then I went to flash in odin the tar i made with patched boot and vbmeta, along with recovery linked. I used matching firmware to what my A10 has also. Would not mind if i could get back into download mode, but that looks impossible now.
Edit3: Managed to get download mode but had to be so quick...hopefully I can reflash stock now.
Cupcake 1.5 said:
Press on app? I have nothing in odin saying that, do you mean ap?
Edit: guess not....i'm bricked, stuck on galaxy logo, device not recognized by pc, holoding power button wont force reboot, nothing lol.
Edit2: can force reboot holding volume down and power but instantly stuck on logo again, cannot power off or enter download, nothing...bricked. Followed this guide to the letter. I assumed when you said app in odin you meant ap since there is no app button. My bootloader unlocked then I went to flash in odin the tar i made with patched boot and vbmeta, along with recovery linked. I used matching firmware to what my A10 has also. Would not mind if i could get back into download mode, but that looks impossible now.
Edit3: Managed to get download mode but had to be so quick...hopefully I can reflash stock now.
Click to expand...
Click to collapse
Im sorry for that and yes i meant AP.
If you wanted to reboot you had to hold vol up vol down and power at the same time and you sure that you unlocked the bootloader and used the right firmware?
Also tell me the AP and from which source have you downloaded it :laugh:
cmz6996 said:
Im sorry for that and yes i meant AP.
If you wanted to reboot you had to hold vol up vol down and power at the same time and you sure that you unlocked the bootloader and used the right firmware?
Also tell me the AP and from which source have you downloaded it :laugh:
Click to expand...
Click to collapse
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Cupcake 1.5 said:
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Click to expand...
Click to collapse
Oh! Im happy to hear that!
Cupcake 1.5 said:
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Click to expand...
Click to collapse
Could you also tell me from where have you downloaded the corrupted firmware so i can warn the others?
cmz6996 said:
Could you also tell me from where have you downloaded the corrupted firmware so i can warn the others?
Click to expand...
Click to collapse
The corruption was my side, I was using a download manager, but when I downloaded through chrome it was all good. As I said, schoolboy error on my part for not checking md5. I used sammobile site for the firmware.
Cupcake 1.5 said:
The corruption was my side, I was using a download manager, but when I downloaded through chrome it was all good. As I said, schoolboy error on my part for not checking md5. I used sammobile site for the firmware.
Click to expand...
Click to collapse
Alr thanks.
Can you upload it to Mediafire? Mega marks a "temporal error"...
Kyua said:
Can you upload it to Mediafire? Mega marks a "temporal error"...
Click to expand...
Click to collapse
At me it works?
Works on a105m?
Axeggus said:
Works on a105m?
Click to expand...
Click to collapse
Yes
i receive message that i running samsumg not official firmware after odin install recovery.tar
not work
cmz6996 said:
So i tried using afaneh92's tutorial which will be linked here : https://forum.xda-developers.com/galaxy-a10/how-to/magisk-root-galaxy-a10-series-t3963822
Which lead to me bootlooping or softbricking and my storage was reduced from 32 gb to 16Gb so i decided to work on my own method!
Credits go to afaneh92 for the Twrp!
BEFORE YOU START YOU SHOULD HAVE
1.Samsung Drivers installed
2.Odin Installed
3.7zip Installed
4.A data transfer cable
5.A Proper working brain
If you have all of those lets start!
A: Phone settings
1.Go in settings>about phone>software information>build number tap that 5 times until it says "You are a developer now" then you will have Developer options unlocked
2.Then go in developer functions and find OEM unlocking tick that on scroll down until you see Usb Debugging and tick that also Disable Auto Updates option
B: Download Your firmware and TWRP
1.Go in your calls app and dial *#1234# Then You will receive some details about your AP, CP etc. look at the AP then download the firmware by searching it on google and (download it from sites like sammobile etc)
2.After you got your firmware connect your device to your pc after its connected send the entire firmware to the device in the Downloads folder
2.1. Install Magisk Manager
3.After you're in magisk manager press on install (first one) then press install again then press Select and Patch a File
3.1.Chose the firmware you saved on the Downloads folder
3.2.After you tap on it it should've already started modifying it
4.After it finished go back to your pc and move the magisk_patched.tar back to your desktop (It should be located in Downloads)
5.From the magisk_patched.tar extract boot.img and vbmeta.img to your desktop
5.1.Download the twrp file here : https://mega.nz/#!OU1WhSDZ!vQz5K1wpqBhg0hCD59aziaHPxFlUsT_2WG8SgT8p6iY
5.2.After recovery.img(TWRP) has been downloaded move it to your desktop
5.3.Select all those three items(vbmeta.img,recovery.img,boot.img) right click then Find 7Zip then press add to archive
5.4.Rename the Archive name to recovery.tar and make sure the archive format is .tar
6.After the Archive has been downloaded follow the steps in C
C :Unlocking The Bootloader and Getting Into Download Mode (THE PART WHERE YOU RESET YOUR PHONE)
1.Turn Off your phone
1.2.Put your data cable into your PC(dont connect your phone to it yet)
1.3.Hold Volume Up and Down then insert the cable into your phone
1.4.When you see a bluescreen let go
1.5.Hold vol up until you see another screen then let go for 1 second and hold vol up again
2.Your device will reset itself and reboot
2.1.After the device has booted in into the setup take the cable out after Turn off your phone
2.2.Hold Vol Up and Down again and connect the cable
2.3.Let go when a blue screen appears then press vol up until you are in download mode
D: Flashing TWRP
1.Open Odin
2.Press on AP then find recovery.tar and press open
3.Press start and let it do its thing
4.After your Phone has rebooted you oficially have TWRP installed
5.If you want to know hoe to root go to step E
E: Installing Magisk
Since magisk is counted as the best rooting option rn i will be using it in this tutorial(Sorry supersu fans)
1.Install Magisk Manager
2.Press on Install (first one) then press install again and after that press Install Zip Only
3.Then go into Twrp by doing the steps below
3.1.Turn off your device
3.2.Hold vol up and power button untill you see TWRP logo
4.Press install
4.1.Find magisk-v20.4(20400).zip
4.2Swipe right on the bottom to flash it then press reboot system now.
5.Now you have TWRP,Root and Magisk Congratulations!
What happens if something goes wrong.
1.SV Error Device 1 library 0 - You installed the wrong firmware look for the right firmware.To check go in recovery mode and look at the A105XXXXXX and then look for a download. Remider AP->AP BL->BL CP->CP HOME_CSC->CSC
2.vbmeta.img error - you have the wrong vbmeta.img file. Redownload the original firmware and take out the right vbmeta.img next time you try flashing. Reminder AP->AP BL->BL CP->CP HOME_CSC->CSC
3.A blue screen telling you to use samsung switch emergency update. That wont work so just flash the original firmware and try flashing twrp again.
4.When i try to boot in it gets me into TWRP - Thats just because that your data is corrupted and to fix it while in TWRP mode press wipe then swipe after its done press Reboot To System. That should be a fix
5.My internal storage is just full of weird numbers and I can't download anything on it! Go in TWRP then wipe,press advanced wipe, click on internal storage and data, swipe. That should fix the error
6.Boootlooping or Bricked! Installed corrupted firmware or the recovery was f-ed up. Then install the right firmware and redo the steps!
If you have issues during the process send it in the comment ill try to respond as fast as i can!
Click to expand...
Click to collapse
hi guy... very good guide but it not work for my galaxy a10 ....i only have unlock the bootloader... if i try to get patched recovery ... it not work.... i have device blocked black screen for samsung software... or i cant go recovery mode it say me a error of vbmeta)
andrea2o18 said:
hi guy... very good guide but it not work for my galaxy a10 ....i only have unlock the bootloader... if i try to get patched recovery ... it not work.... i have device blocked black screen for samsung software... or i cant go recovery mode it say me a error of vbmeta)
Click to expand...
Click to collapse
You installed the wrong fir.ware check your right firmware.
BlueFolks said:
i receive message that i running samsumg not official firmware after odin install recovery.tar
Click to expand...
Click to collapse
Be cause you modified the firmware ignore that message
have you fixed the storage reduced to 16gb problem?
I have a Samsung galaxy sm-a10. I've tried everything here, even combination files. The error I ALWAYS get is 'failed flashing ROM... OEM lock'
Of course I have unlocked OEM in developer options, but still I get this error in the bootloader.
Any ideas?

Galaxy a70 a705fn stuck on partition boot reason boot : hash of data does not match d

Galaxy a70 a705fn stuck on partition
<!>
boot reason boot : hash of data does not match digest in description . (2nd) (3)
Calculated hash of (boot) : F5877D7EDC. (VEMETA) : 98EEF63C0
SAMSUNG boot. A706FNXXU5BTE3, 31342670R
VBMETA A705FNXXU5BTC2, 296911020R
Plz i cant flash stock firmware now it happened after a minor update
Same here but with the following parameters:
boot reason boot : hash of data does not match digest in description . (2nd) (3)
Calculated hash of (boot) : A7681EDC3D. (VEMETA) : 98EEF63C0
SAMSUNG boot. A705FNXXU5BTF1, 31708158R
VBMETA A705FNXXU5BTC2, 29691020R
Also after a minor update, please help!
NB: Phone was rooted but later flashed official ROM but left bootloader unlocked.
winterxda said:
Same here but with the following parameters:
boot reason boot : hash of data does not match digest in description . (2nd) (3)
Calculated hash of (boot) : A7681EDC3D. (VEMETA) : 98EEF63C0
SAMSUNG boot. A705FNXXU5BTF1, 31708158R
VBMETA A705FNXXU5BTC2, 29691020R
Also after a minor update, please help!
NB: Phone was rooted but later flashed official ROM but left bootloader unlocked.
Click to expand...
Click to collapse
I used the following solution which I found on a Samsung forum and it worked!
:good::good::good:
Hello Every One,
I had the same issue after trying to update my A70 phone based on a message which poped up from samsung asking me to update.
A friend of mine managed to resolve my issue without losing any data using that method:
1st : from the error msg --- > last line you will find the firmware version ex: A705FNXXU4ASK6
2nd: Goto https://www.sammobile.com/ --> Devices --> Choose your model --> Firmware --> Choose your country and download the firmware. (Download it and unzip it)
3rd: Download a software called Odin and follow the instruction ( MAKE SURE TO UNCHECK RE-PARTITION FIELD FROM OPTIONS TAB) IF YOU WANT TO KEEP YOU DATA
4th: In my case i have a new model so i uploaded the following 4 files ( BL , AP , CP , HOME_CSC) after i pluged the cable.
Dont forget to uncheck the Re-partition.
Click Start
winterxda said:
Same here but with the following parameters:
boot reason boot : hash of data does not match digest in description . (2nd) (3)
Calculated hash of (boot) : A7681EDC3D. (VEMETA) : 98EEF63C0
SAMSUNG boot. A705FNXXU5BTF1, 31708158R
VBMETA A705FNXXU5BTC2, 29691020R
Also after a minor update, please help!
NB: Phone was rooted but later flashed official ROM but left bootloader unlocked.
Click to expand...
Click to collapse
It locked my boot loader And I was previously fully rooted Now I’m stuck on the blue screen
My tablet starting you shut off for 30sec then come back on. Then it started to this **** completely off and reboot and they will get to the home screen and when I would soon as I would open an app it would reboot all over again and I did it over and over and over then I was trying to clear the chase and somehow it did this and I was previously fully rooted with supersu and the maskis one

samsung a505f stuck on logo

hi i wanted to flash magisk using twrp so i had to install twrp first using odin i followed all instructions in there androidweblog.com/samsung-galaxy-a50-sm-a505f-root-install-twrp-recovery
and flashed that twrp zip file
mega.nz/#!SWYwAQAb!bbLnex8yhT7tyBTdTMr2wIS-tzITjg5VMJ_p1msXenQ
but after flashing
the phone is stuck in samsung a50 logo and i can do nothing except opening download mode
and i get error this phone's bootloader is unlocked and its software integrity can't be verified any data on this phone maybe un vulnerable to attackers don't software any important or sensitive information on this phone
what should i do to bring it back and uninstall flashed twrp
thanks in advance
1) Find you firmware [https://www.sammobile.com/firmwares/search/a505/]
-Clicking on your model will present you with firmware downloads
-Find yours and download it [country and network or just the country should work]
-Extract it somewhere.
2) Get Odin [https://dl2018.sammobile.com/Odin3-v3.14.4.zip]
-Extract it somewhere
-Load it
-Add the files from the firmware folder into the correct sections (i.e/ ap, bl, csc - I cant remeber them all of the top of my head)
3) Get into download mode
-Power off device or if its boot looping Press and hold power + vol down to force a restart
-Press and hold both vol buttons and connect it to your computer with usb
-Odin should now say added in the log
4) press start and wait

Categories

Resources