Related
SAMSUNG GALAXY NOTE 2
SOLUTION/FIXING/RESOLUTION/RECOVERY TO BOOTLOOP/ERROR: CAN’T WRITE TO PARTITION/ODIN FAILUREDownload following files:
1. PC Odin latest version.
2. .PIT file for Your Device Version (GT N7100/7105 etc.)
3. Stock firmware of your choice.
4. Samsung Kies.
Procedure:
1. Install Samsung KIES on your PC.
2. Run Odin on your PC.
3. Remove memory and sim card (if available) from your device reinstall battery.
4. Reboot your device to download mode for this PRESS AND HOLD VOL DOWN+POWER+HOME BUTTONS SIMULTANEOUSLY that will display warning (do not fear) now press VOL DOWN AGAIN.
5. Connect your device to PC.
6. On ODIN window, click on AP and browse downloaded stock firmware (will take a minute to load). Then Click on PIT and browse downloaded “.PIT” file for your device specifically. And check/tick “Full NAND Erase”. DO NOT CHANGE (CHECK OR UNCHECK) ANY OTHER OPTIONS ON ODIN
7. Click on start and sit back leaving device, PC and cables untouched.
8. After completion of flashing your will reboot automatically. Now disconnect your device from PC.
9. If it gets stuck on boot logo then pull out battery and reinstall. Then go to recovery mode (BY PRESSING VOL UP+ POWER+HOME AT THE SAME TIME) and clean cache.
10. Then Reboot your device and enjoy.
DISCLAIMER: IT HELPED ME AND MANY MORE BUT AT THE SAME THIS INFORMATION MAY NOT HELP EVERYONE SO RESPONOSIBILITY FOR BRICKING/DAMAGING/LOOSING YOUR DEVICE ENTIRELY LIES ON YOU.
I purchased a used Samsung Galaxy Tab S 10.5 on ebay. Originally it had Android 4.4.2
When I turned it on the device is in retail demo mode.
I have tried the following
1) passwords found on this forum such as (5444, M729Q16K8546, blue, unlimited, easy, galaxy)
2) none of these worked
3) Can not deselect "samsung retail mode" in settings/security/administrators
I tried updating to android 6.0.1 by doing the following but the retail mode is still there
It will not enter into download mode so I did the following
1) Enabled developer options on tablet
2) Used command "adb reboot download"
3) Installed Android 6.0.1 stock rom (T800XXU1CPH7_T800XAR1CPH4_XAR.zip) from sammobile.com
4) Tablet installed and updated Android
5) Retail mode is still there and I still can not get rid of it
Any suggestions are greatly appreciated
Thanks
Never had a retail demo device so my answer may be limited.
Did you tried/are able to install TWRP ?
If you can get TWRP you can try to make a complete factory wipe (Advanced Wipe > check all the boxes > wipe)
Then reboot to download mode (Reboot > Download)
Install the stock rom again
Here is the link: https://forum.xda-developers.com/ga...p-2-8-6-1-unofficial-sm-t800-805-807-t3074633
Flash it via odin
I have tried to do TWRP but can not get it to work. I did not use the apk I was using ODIN on my pc. I was using a TWRP file twrp_3.0.0-0_T800. Not sure if that was the issue or not.
Here are the steps I used:
1) put phone into download mode by using adb on pc (adb reboot download)
2) In ODIN
a) turn off autop reboot
b) select AP file twrp_3.0.0-0_T800
c) wait for success in ODIN
3) tablet never rebooted so I used these keys (press at same time until reboot power+vol down+vol up+home)
4) Tablet rebooted into normal running mode
If you don't enter in recovery right away you flash it the system will revert the changes back. so if the system start to boot normally you need to flash via odin again.
I recommend you to flash the version i linked, as it is more compatible with MM bootloader, also turning off auto reboot is a very important thing.
You need to press all the buttons together power+vol down+vol up+home, (press power last) . when the screen light up release the volume up button (the next to power button) and keep holding the rest.
also...
You can try one trick that i use sometimes, it will give you more time to make the key combination, connect the device to the charger and press and hold power+vol up until the screen turn off, it may show a battery icon, so you disconnect the charger and wait the icon go away. the device should be turned off now. so you basically press and hold vol down+home+power (press power last)
If you done the combination correctly and the screen became black, don't worry, it is a bug, just wait some time (1 min i think) and press home key, it should show the recovery.
It can be a pain in the a** sometimes... but trust me, it generally works.
Ok, so far so good. It took a while but I got into TWRP. But I can't seem to select the image file.
I have it on an external MicroSD in the root. File is called T800XXU1CPH7_T800XAR1CPH4_XAR.zip
I can browse files on the list on the left. But I can't seem to find the file
Did I miss a step?
Somehow after going through menus, it recognized the file
But when I tried to install it, I got these errors
Zip Signature verification failed!
Error installing zip file /sdcard/download/T800XXU1CPH7_T800ZXAR1CPH4_XAR.zip
Could not find 'META-INF/com/google/android/update-binary' in zip file
Error installing zip file /sdcard/download/T800XXU1CPH7_T800ZXAR1CPH4_XAR.zip
you got me wrong, in the TWRP what you need to do is make a complete wipe (Wipe > Advanced Wipe > check all the boxes > wipe)
then you need to enter in download mode. (Reboot > Download)
and flash the rom via odin!
extract the zip on your pc, it should be a .Tar file, select AP mode on odin, select the .tar and flash it in there.
I apologize for the confusion. Those steps worked!!
I think part of the problem is that I did not extract the firmware file. I kept trying to flash the TAR file.
I did a wipe in TWRP
Then rebooted into download mode
Flashed extracted firmware file in ODIN in AP Box
Then the tablet rebooted and was in setup mode like a brand new tablet!! Who hoo.
Works great
Thanks for all the help
Work only on Oreo 8
You must be Stat Normal
Oem Unlocked
Enable USB Debugging Mode and OEM Unlock in your mobile. To do this; go to settings >>> about >>> Tap on the “Build Number” 7-10 times consistently to enable “Developer Options,” then go to the “Developer Options” and enable USB Debugging Mode and OEM Unlock. There is no complicated process in the Samsung Galaxy J7 Duo.
Download and install the Samsung USB driver to your computer system.
Also, download the ODIN software. Select above Oreo version in the ODIN list. Install ODIN in your PC.
Download Magisk.Zip (Download Latest version) and forced encryption disabler, Copy it to Your Phone Memory. We Need to flash encryption disabler to avoid Boot Warnings in the future after the Root process.
Download and save the TWRP File. Select Correct TWRP file from Below. This TWRPs can support Up to Oreo.
SM-J720F
SM-J720M
Flash TWRP using ODIN
Samsung Galaxy J7 Duo Download Mode
Connect your USB Cable with PC. Switch off your device. Then, enter into Download mode. To do this; press and hold down the Volume Down + Home + Power buttons and connect your micro USB Cable.
Samsung Galaxy J7 Duo Download Mode Warning Screen
Press the Volume Up button to continue when you see the warning message.
Now, connect the Samsung Galaxy J7 Duo mobile to the computer via USB cable.
Launch the Odin app on your computer. If the device is detected by this app (Odin), it will show you a message that reads – added!!!
ODIN Added Message
However, if the device is not correctly connected to the PC, you won’t see this message. So, you have to check the USB cable if it is reasonable and reconnect the device.
After connecting the Samsung device, click on the PDA/PA button to browse/search and get the TWRP from where you saved it on your PC. Also, navigate to “options” and tick the Auto Reboot.
Odin Auto Reboot
Click on “Start”
Once the file is loaded into the device, reboot your device.
Kudos, you have just Installed the TWRP on your Samsung Galaxy J7 Duo. If you installed TWRP, Don’t turn on your mobile. Immediately, move to Magisk Installation steps.
You should not Boot into Normal OS Booting, after TWRP. After TWRP Flash, Immediately Boot into Recovery or twrp will gone
Boot it Into recovery mode->Volume Up + Power Button.+Home
Now it Will Boot into TWRP Recovery Mode.
Install Magisk, forced encryption disabler in your Samsung Galaxy J7 Duo using TWRP
Select Wipe->Advance Wipe->Select Cache Data.
Return to Home of TWRP select Install.
Select Magisk.Zip.
After Installation again Navigate to Home select Install. Select forced encryption disabler.
After the Installation Reboot Your Mobile.
You can also install Magisk.apk in your Mobile Applications. Forced encryption disabler is used to avoid the boot loop issue after rooting.
enjoy
SM-J720F
SM-J720M
encryption disabler
Samy6699 said:
Work only on Oreo 8
SM-J720F
SM-J720M
enjoy
SM-J720F
SM-J720M
encryption disabler
Click to expand...
Click to collapse
Can it be used on the Dual-Sim version SM-J720F/DS released in 04/2018 ?
Can i install it on Galaxy J7 Duo running Android pie
Nitin devarasetty said:
Can i install it on Galaxy J7 Duo running Android pie
Click to expand...
Click to collapse
i also need that man.
Please make one thing clear
Do we have to turn off "Auto reboot"
Or keep the "Auto reboot" option checked on?
Android 9.0
Hello, when it will be possible ? If never, why ?
I followed the exact process but everytime i tried to boot into TWRP recovery immediately after the flashing, the device still boots into stock recovery instead of TWRP
Please help me with this
Thank you
I figured out a way to root the Galaxy J7 duo
Actually i have tried lot of ways to root using TWRP flash and all.. but one day i accidentally bricked my device
So i downloaded the stock ROM to flash my device
And i downloaded the 8.0 android ROM
So this root method basically tested on android 8.0
So now i have android 8.0 stock ROM downloaded
Step 1 -
So make sure you also downloaded the ROM
And extract the ROM file (you must have got the "AP" "CP" "BL" "CSC" and "HOME CSC" file)
Then copy the "AP" file in your phone
Then install magisk manager in your phone
Open magisk, select install, select and patch a file from magisk
Then select "AP" file
And wait while magisk is patching the "AP" file
When flashing is done the patched file will be saved on storage, emulated, 0, download (file will be saved as "magisk_patched.tar")
Then simply copy the patched file in your computer
Step 2 -
Open odin in your Computer
In odin, select "magisk_patched.tar" in "AP" section
Select "BL" from the stock ROM folder in the odin's "BL" section
Select "CP" from the stock ROM folder in the odin's "CP" section
Select "HOME CSC" from the stock ROM folder in the odin's "HOME CSC" section
make sure you select all the official files from the stock ROM folder... just instead of the "AP" file, select the "magisk_patched.tar"
Then connect your phone via USB cable
Odin will detect and show "added" message
Start the flashing process
It will take few minutes
When its done your phone will boot up
But it will show something like "erasing" and "verification unsuccessful"
Just agree with that and erase the phone
(It will cause a data loss because everything will be deleted and your phone will reset, so i suggest to make a backup using samsung smart switch)
Then when your phone will reboot, just follow the steps to setup
Amd install magisk latest apk
Open magisk and boom!
You can already realize that magisk root is activated
Amd magisk will ask you to "setup environment"
Just agree and your phone will reboot withing 5 seconds
And done!
Your phone is now rooted
Install root checker and verify your root status
how to un-brick
Same thing here,
Tell me how you un-bricked your phone
I bricked my phone by installing wrong twrp file to sm-j720f android pie with odin
and now it shows only bootloader screen and I can't even go to recovery mode or home screen just showing " SAMSUNG GALAXY J7 DUO secured by Knox powerd by android" noting else
That is exactly what was happened in my phone
So what i did just downloaded the Stock ROM for J7 duo from the sam mobile website.
Then extract the ROM and you will get few files ("AP", "BL", "CP", "CSC", "HOME CSC")
Then boot your phone into download mode using this method
(Connect the phone to your PC using USB cable, then press and hold Power + volume down + home, then when the "powered by android" logo appears release only the power button... so your phone will boot into download mode, press volume up to continue)
Now, in odin you can see "added" message that means device is connected
Now select the ROM files respectively, BL, AP, CP, CSC
Then click start, and the process will start, will take few minutes
When done, your phone will boot normally
Yeah everything is right until...
[grand_theft;83142325]That is exactly what was happened in my phone
***********
So what i did just downloaded the Stock ROM for J7 duo from the sam mobile website.
Then extract the ROM and you will get few files ("AP", "BL", "CP", "CSC", "HOME CSC") *********
Then boot your phone into download mode using this method
Fact that I cant even go to download mode I tried out many times
Just follow this step
(Connect your computer with your phone using USB cable, then press and hold Power + volume down + home, then when the phone vibrates and appears the samsung logo again just release only the power key, while holding the volume down and home key)
(Just release only the power key when the "powered by android" logo appears)
Thats how you can go to the download mode
No virtual change
Done it as u say,
But my mobile shows noting but just logo screen
*****SAMSUNG GALAXY J7 DUO secured by Knox powered by android*****
again and again
These is not first time, last I did the same mistake before and I went to Samsung service store they recovered it, I don't know how they did but it worked.
These time I want to (tring to) do it on my own bcoz I love playing with ROM's, root, etc.
Thanks for replys
I also did the same mistake by flashing wrong TWRP
But however i managed to enter into downlod mode following those steps
And flashed official ROM to unbrick the phone
You must go into download mode to flash the official ROM using odin
Thanks alot
Thanks man,
I'm able to enter download mode and I installed official ROM. Now in using it as normal but (1)Secure folder and Pay mini are not working.
(2)Do you have any idea on other ROMs that works on SM-J720F other than Samsung's one UI.
(3)can I install android 8 on it in ordered to root as you said it in previous post.
(4)from previous your post on oreo twrp explanation, is twrp works fine. What happens to twrp if I update phone to Q (from system updater)
I'm glad you made it!
Now,
1) Secure folder and pay mini won't work because the phone thinks you rooted your phone and maybe your binary is cracked (so forget using those)
2) I'm not sure about any ROMs which is stable with this model. But you can search the internet (I think pixel ROM is pretty popular)
3) I'm not sure if my process of rooting supports android 9.0 or not, because i personally tetsted it on 8.0, So you can download the oreo ROM from the internet and then follow all the steps i mentioned before
4) If you want to install TWRP, you can still install TWRP after rooting via the method i provided
(You can install TWRP using flashify on a rooted phone)
But if you want root access then you can simply root your phone first..
And whatever custom ROMs you want to install, install it using flashify
Because if you update software via official OTA, the root access and TWRP both will be gone
And if you root your phone, then however you won't be able to perform a official OTA update.
(First root your phone, then simply download your TWRP file and flash it with root permission within your phone)
Instated of Oreo AP file,
grand_theft said:
I figured out a way to root the Galaxy J7 duo
Actually i have tried lot of ways to root using TWRP flash and all.. but one day i accidentally bricked my device
So i downloaded the stock ROM to flash my device
And i downloaded the 8.0 android ROM
So this root method basically tested on android 8.0
So now i have android 8.0 stock ROM downloaded
Step 1 -
So make sure you also downloaded the ROM
And extract the ROM file (you must have got the "AP" "CP" "BL" "CSC" and "HOME CSC" file)
Then copy the "AP" file in your phone
Then install magisk manager in your phone
Open magisk, select install, select and patch a file from magisk
Then select "AP" file
And wait while magisk is patching the "AP" file
When flashing is done the patched file will be saved on storage, emulated, 0, download (file will be saved as "magisk_patched.tar")
Then simply copy the patched file in your computer
Step 2 -
Open odin in your Computer
In odin, select "magisk_patched.tar" in "AP" section
Select "BL" from the stock ROM folder in the odin's "BL" section
Select "CP" from the stock ROM folder in the odin's "CP" section
Select "HOME CSC" from the stock ROM folder in the odin's "HOME CSC" section
make sure you select all the official files from the stock ROM folder... just instead of the "AP" file, select the "magisk_patched.tar"
Then connect your phone via USB cable
Odin will detect and show "added" message
Start the flashing process
It will take few minutes
When its done your phone will boot up
But it will show something like "erasing" and "verification unsuccessful"
Just agree with that and erase the phone
(It will cause a data loss because everything will be deleted and your phone will reset, so i suggest to make a backup using samsung smart switch)
Then when your phone will reboot, just follow the steps to setup
Amd install magisk latest apk
Open magisk and boom!
You can already realize that magisk root is activated
Amd magisk will ask you to "setup environment"
Just agree and your phone will reboot withing 5 seconds
And done!
Your phone is now rooted
Install root checker and verify your root status
Click to expand...
Click to collapse
************************************************************************************************************************************************************************************************************************************************************************************************************
Ok I agree with you,
But what if I replace Oreo's AP file with android 10's AP file(which I installed recently on my phone), will it boot with root or not.
************************************************************************************************************************************************************************************************************************************************************************************************************
I have not tested this method on any other android version, you can still try it on your own, there is nothing to lose, just make a backup before flashing. If you succeed then that's great
But i have personally tested this method only on android 8.0
(Before doing anything, just make a proper backup using samsung smart switch. So you can restore your important data)
Success
Replaced with android 10's AP file and flashed with Odin. Now my phone has rooted with Magisk manager.
Any suggestions to tweak android
Claudio4780 said:
Can it be used on the Dual-Sim version SM-J720F/DS released in 04/2018 ?
Click to expand...
Click to collapse
Have you ever got the answer or figured it out? I've got the same model and I cannot find anything on the net to help me with rooting this phone.
READ EVERYTHING CAREFULLY!
1.Your phone warranty will be void after this tutorial!
2.Any small mistake and your phone is bricked/bootlooped!
3.All of your data will be lost so back it up somewhere
Click to expand...
Click to collapse
(Fixed the tutorial my bad.)
Click to expand...
Click to collapse
Hey Guys Im Back! Thank you for the support and how it blew up. I have tested this on Android 10 UI 2.0 and it works better then ever!
Also installed lineage os : https://forum.xda-developers.com/galaxy-a10/development/rom-lineage-os-a10-a105f-t4078093
So i tried using afaneh92's tutorial which will be linked here : https://forum.xda-developers.com/galaxy-a10/how-to/magisk-root-galaxy-a10-series-t3963822
Which lead to me bootlooping or softbricking and my storage was reduced from 32 gb to 16Gb so i decided to work on my own method!
Credits go to afaneh92 for the Twrp!
BEFORE YOU START YOU SHOULD HAVE
1.Samsung Drivers installed
2.Odin Installed
3.7zip Installed
4.A data transfer cable
5.A Proper working brain
If you have all of those lets start!
A: Phone settings
1.Go in settings>about phone>software information>build number tap that 5 times until it says "You are a developer now" then you will have Developer options unlocked
2.Then go in developer functions and find OEM unlocking tick that on scroll down until you see Usb Debugging and tick that also Disable Auto Updates option
B: Download TWRP and 2 other important files
1.Dial *#1234# and it will show the AP and some others, focus on AP paste it on google and get the download for it
2.After downloaded move the AP to your download folder in your android device
3.You will get a magisk_patched.tar after its been offically converted
4.Get the twrp for a10
Download the twrp file here : https://mega.nz/#!OU1WhSDZ!vQz5K1wpqBhg0hCD59aziaHPxFlUsT_2WG8SgT8p6iY
5.After you got everything open the .tar archive and extract vbmeta.img, boot.img and you should already have recovery.img on your Desktop
6.Grab all the 3 .img files and archive them into a .tar using 7zip, Now continue to step C,
C :Unlocking The Bootloader and Getting Into Download Mode (THE PART WHERE YOU RESET YOUR PHONE)
1.Turn Off your phone
1.2.Put your data cable into your PC(dont connect your phone to it yet)
1.3.Hold Volume Up and Down then insert the cable into your phone
1.4.When you see a bluescreen let go
1.5.Hold vol up until you see another screen then let go for 1 second and hold vol up again
2.Your device will reset itself and reboot
2.1.After the device has booted in into the setup take the cable out after Turn off your phone
2.2.Hold Vol Up and Down again and connect the cable
2.3.Let go when a blue screen appears then press vol up until you are in download mode
D: Flashing TWRP
1.Open Odin
2.Press on AP then find Desktop.tar and press open
3.Press start and let it do its thing
4.After your Phone has rebooted you oficially have TWRP installed
5.If you want to know hoe to root go to step E
E: Installing Magisk
Since magisk is counted as the best rooting option rn i will be using it in this tutorial(Sorry supersu fans)
1.Install Magisk Manager
2.Press on Install (first one) then press install again and after that press Install Zip Only
3.Then go into Twrp by doing the steps below
3.1.Turn off your device
3.2.Hold vol up and power button untill you see TWRP logo
4.Press install
4.1.Find magisk-v20.4(20400).zip
4.2Swipe right on the bottom to flash it then press reboot system now.
5.Now you have TWRP,Root and Magisk Congratulations!
What happens if something goes wrong.
1.SV Error Device 1 library 0 - You installed the wrong firmware look for the right firmware.To check go in recovery mode and look at the A105XXXXXX and then look for a download. Remider AP->AP BL->BL CP->CP HOME_CSC->CSC
2.vbmeta.img error - you have the wrong vbmeta.img file. Redownload the original firmware and take out the right vbmeta.img next time you try flashing. Reminder AP->AP BL->BL CP->CP HOME_CSC->CSC
3.A blue screen telling you to use samsung switch emergency update. That wont work so just flash the original firmware and try flashing twrp again.
4.When i try to boot in it gets me into TWRP - Thats just because that your data is corrupted and to fix it while in TWRP mode press wipe then swipe after its done press Reboot To System. That should be a fix
5.My internal storage is just full of weird numbers and I can't download anything on it! Go in TWRP then wipe,press advanced wipe, click on internal storage and data, swipe. That should fix the error
6.Boootlooping or Bricked! Installed corrupted firmware or the recovery was f-ed up. Then install the right firmware and redo the steps!
If you have issues during the process send it in the comment ill try to respond as fast as i can!
i notice thread title says exynos only.. u do know they are all exynos including a102u and a102u1 right?
Oh. Alright thanks for telling me.
Press on app? I have nothing in odin saying that, do you mean ap?
Edit: guess not....i'm bricked, stuck on galaxy logo, device not recognized by pc, holoding power button wont force reboot, nothing lol.
Edit2: can force reboot holding volume down and power but instantly stuck on logo again, cannot power off or enter download, nothing...bricked. Followed this guide to the letter. I assumed when you said app in odin you meant ap since there is no app button. My bootloader unlocked then I went to flash in odin the tar i made with patched boot and vbmeta, along with recovery linked. I used matching firmware to what my A10 has also. Would not mind if i could get back into download mode, but that looks impossible now.
Edit3: Managed to get download mode but had to be so quick...hopefully I can reflash stock now.
Cupcake 1.5 said:
Press on app? I have nothing in odin saying that, do you mean ap?
Edit: guess not....i'm bricked, stuck on galaxy logo, device not recognized by pc, holoding power button wont force reboot, nothing lol.
Edit2: can force reboot holding volume down and power but instantly stuck on logo again, cannot power off or enter download, nothing...bricked. Followed this guide to the letter. I assumed when you said app in odin you meant ap since there is no app button. My bootloader unlocked then I went to flash in odin the tar i made with patched boot and vbmeta, along with recovery linked. I used matching firmware to what my A10 has also. Would not mind if i could get back into download mode, but that looks impossible now.
Edit3: Managed to get download mode but had to be so quick...hopefully I can reflash stock now.
Click to expand...
Click to collapse
Im sorry for that and yes i meant AP.
If you wanted to reboot you had to hold vol up vol down and power at the same time and you sure that you unlocked the bootloader and used the right firmware?
Also tell me the AP and from which source have you downloaded it :laugh:
cmz6996 said:
Im sorry for that and yes i meant AP.
If you wanted to reboot you had to hold vol up vol down and power at the same time and you sure that you unlocked the bootloader and used the right firmware?
Also tell me the AP and from which source have you downloaded it :laugh:
Click to expand...
Click to collapse
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Cupcake 1.5 said:
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Click to expand...
Click to collapse
Oh! Im happy to hear that!
Cupcake 1.5 said:
All sorted now, back on stock with twrp and root It was a schoolboy error by me, the firmware downloaded was corrupted lol.
Click to expand...
Click to collapse
Could you also tell me from where have you downloaded the corrupted firmware so i can warn the others?
cmz6996 said:
Could you also tell me from where have you downloaded the corrupted firmware so i can warn the others?
Click to expand...
Click to collapse
The corruption was my side, I was using a download manager, but when I downloaded through chrome it was all good. As I said, schoolboy error on my part for not checking md5. I used sammobile site for the firmware.
Cupcake 1.5 said:
The corruption was my side, I was using a download manager, but when I downloaded through chrome it was all good. As I said, schoolboy error on my part for not checking md5. I used sammobile site for the firmware.
Click to expand...
Click to collapse
Alr thanks.
Can you upload it to Mediafire? Mega marks a "temporal error"...
Kyua said:
Can you upload it to Mediafire? Mega marks a "temporal error"...
Click to expand...
Click to collapse
At me it works?
Works on a105m?
Axeggus said:
Works on a105m?
Click to expand...
Click to collapse
Yes
i receive message that i running samsumg not official firmware after odin install recovery.tar
not work
cmz6996 said:
So i tried using afaneh92's tutorial which will be linked here : https://forum.xda-developers.com/galaxy-a10/how-to/magisk-root-galaxy-a10-series-t3963822
Which lead to me bootlooping or softbricking and my storage was reduced from 32 gb to 16Gb so i decided to work on my own method!
Credits go to afaneh92 for the Twrp!
BEFORE YOU START YOU SHOULD HAVE
1.Samsung Drivers installed
2.Odin Installed
3.7zip Installed
4.A data transfer cable
5.A Proper working brain
If you have all of those lets start!
A: Phone settings
1.Go in settings>about phone>software information>build number tap that 5 times until it says "You are a developer now" then you will have Developer options unlocked
2.Then go in developer functions and find OEM unlocking tick that on scroll down until you see Usb Debugging and tick that also Disable Auto Updates option
B: Download Your firmware and TWRP
1.Go in your calls app and dial *#1234# Then You will receive some details about your AP, CP etc. look at the AP then download the firmware by searching it on google and (download it from sites like sammobile etc)
2.After you got your firmware connect your device to your pc after its connected send the entire firmware to the device in the Downloads folder
2.1. Install Magisk Manager
3.After you're in magisk manager press on install (first one) then press install again then press Select and Patch a File
3.1.Chose the firmware you saved on the Downloads folder
3.2.After you tap on it it should've already started modifying it
4.After it finished go back to your pc and move the magisk_patched.tar back to your desktop (It should be located in Downloads)
5.From the magisk_patched.tar extract boot.img and vbmeta.img to your desktop
5.1.Download the twrp file here : https://mega.nz/#!OU1WhSDZ!vQz5K1wpqBhg0hCD59aziaHPxFlUsT_2WG8SgT8p6iY
5.2.After recovery.img(TWRP) has been downloaded move it to your desktop
5.3.Select all those three items(vbmeta.img,recovery.img,boot.img) right click then Find 7Zip then press add to archive
5.4.Rename the Archive name to recovery.tar and make sure the archive format is .tar
6.After the Archive has been downloaded follow the steps in C
C :Unlocking The Bootloader and Getting Into Download Mode (THE PART WHERE YOU RESET YOUR PHONE)
1.Turn Off your phone
1.2.Put your data cable into your PC(dont connect your phone to it yet)
1.3.Hold Volume Up and Down then insert the cable into your phone
1.4.When you see a bluescreen let go
1.5.Hold vol up until you see another screen then let go for 1 second and hold vol up again
2.Your device will reset itself and reboot
2.1.After the device has booted in into the setup take the cable out after Turn off your phone
2.2.Hold Vol Up and Down again and connect the cable
2.3.Let go when a blue screen appears then press vol up until you are in download mode
D: Flashing TWRP
1.Open Odin
2.Press on AP then find recovery.tar and press open
3.Press start and let it do its thing
4.After your Phone has rebooted you oficially have TWRP installed
5.If you want to know hoe to root go to step E
E: Installing Magisk
Since magisk is counted as the best rooting option rn i will be using it in this tutorial(Sorry supersu fans)
1.Install Magisk Manager
2.Press on Install (first one) then press install again and after that press Install Zip Only
3.Then go into Twrp by doing the steps below
3.1.Turn off your device
3.2.Hold vol up and power button untill you see TWRP logo
4.Press install
4.1.Find magisk-v20.4(20400).zip
4.2Swipe right on the bottom to flash it then press reboot system now.
5.Now you have TWRP,Root and Magisk Congratulations!
What happens if something goes wrong.
1.SV Error Device 1 library 0 - You installed the wrong firmware look for the right firmware.To check go in recovery mode and look at the A105XXXXXX and then look for a download. Remider AP->AP BL->BL CP->CP HOME_CSC->CSC
2.vbmeta.img error - you have the wrong vbmeta.img file. Redownload the original firmware and take out the right vbmeta.img next time you try flashing. Reminder AP->AP BL->BL CP->CP HOME_CSC->CSC
3.A blue screen telling you to use samsung switch emergency update. That wont work so just flash the original firmware and try flashing twrp again.
4.When i try to boot in it gets me into TWRP - Thats just because that your data is corrupted and to fix it while in TWRP mode press wipe then swipe after its done press Reboot To System. That should be a fix
5.My internal storage is just full of weird numbers and I can't download anything on it! Go in TWRP then wipe,press advanced wipe, click on internal storage and data, swipe. That should fix the error
6.Boootlooping or Bricked! Installed corrupted firmware or the recovery was f-ed up. Then install the right firmware and redo the steps!
If you have issues during the process send it in the comment ill try to respond as fast as i can!
Click to expand...
Click to collapse
hi guy... very good guide but it not work for my galaxy a10 ....i only have unlock the bootloader... if i try to get patched recovery ... it not work.... i have device blocked black screen for samsung software... or i cant go recovery mode it say me a error of vbmeta)
andrea2o18 said:
hi guy... very good guide but it not work for my galaxy a10 ....i only have unlock the bootloader... if i try to get patched recovery ... it not work.... i have device blocked black screen for samsung software... or i cant go recovery mode it say me a error of vbmeta)
Click to expand...
Click to collapse
You installed the wrong fir.ware check your right firmware.
BlueFolks said:
i receive message that i running samsumg not official firmware after odin install recovery.tar
Click to expand...
Click to collapse
Be cause you modified the firmware ignore that message
have you fixed the storage reduced to 16gb problem?
I have a Samsung galaxy sm-a10. I've tried everything here, even combination files. The error I ALWAYS get is 'failed flashing ROM... OEM lock'
Of course I have unlocked OEM in developer options, but still I get this error in the bootloader.
Any ideas?
[28NOV20][Guide] How To ROOT ALL US VER. NOTE 10(+) & Flash TWRP (SnapDragon Only)
Step by Step: How to Root & Flash TWRP on Samsung Galaxy Note 10(+) and Every other Galaxy from S10 and up (SnapDragon Only)
Update: If You Want To Unlock Your Bootloader go here: U.S. Samsung Galaxy Bootloader Unlock Service
So You Figured Out How to Unlock The Bootloader on your Shiny New/Old (Snapdragon) Samsung Galaxy Thing-a-ma-jig
Good on you, but now you want to figure out how to Root properly and enjoy the spoils of said Unlock. Well You've come to right place.
DO NOT QUOTE THE OP PLEASE, (If you would like to place this guide in your respective Device Threads ie. Galaxy s10, s20, s20 Note 20 Ultra 5g etc. thats perfectly fine)
Welcome: Be nice, be courteous and *enjoy
Before you move further, make clear that rooting device -
- Your warranty will be void
- Some of functions may not work on rooted device, some function may get back with unrooting, some functions may never.
- All your data on device will be lost (Factory Reset is in the Instructions below)
- Flashing custom binaries may brick (Usually it's a soft but can be hard brick too), so follow it on your own risk!
Now that you accept the risks, let's have some fun -
Important: Although this is a simple guide you must follow all directions clearly
Simple guide to root your device and install TWRP after unlock: (Thanks to @Krog18 )
1. Download vbmeta_disabled.tar, TWRP for your device, magisk and multidisabler-samsung-2.6-afaneh92
2. Reboot to download mode and flash vbmeta_disabled.tar in ap slot and reboot. Device will reboot to recovery mode prompting you to wipe data so wipe data and reboot to download mode again.
3. Uncheck auto reboot in Odin and flash TWRP in ap slot.
4. Hold volume down and power until the screen goes black then immediately switch to holding volume up, Bixby button (10 series only) and power to reboot into TWRP
5. Flash multidisabler and reboot recovery
6. Go to wipe, format and type yes to format data
7. Flash magisk
8. Make a backup of efs and store it somewhere safe
9. Reboot
*First boot may take 10-15 minutes. If it doesn't boot in 15 minutes, force reboot by holding power and volume down for at least 10 seconds
Additional Method For Rooting If Above method did not work for you:
Step 1 : (Root Base Firmware with Magisk By patching files yourself, Then Flash TWRP in Odin)
Prepare Firmware files for root
You need to Patch AP File to flash using Odin to root device.
1. Download stock firmware for your device ie (SM-N975U/U1, SM-G973U/U1, SM-G975U/U1)
You need to download file according your region and model.
2. Once you finish download, extract files and keep all files on in a folder on the desktop of PC. From extracted files find the file with name AP_[device_model_sw_ver].tar.md5 copy to your Phone.
3.Download Latest Magisk Manager and Install to your device (Make sure to check for updates) (Optionally go into settings and switch the update channel to BETA)
4.Open Magisk Manager - Find Magisk Install (Top One) - Click Install - select to "Select and Patch file" - Click the AP file you have copied to your device (AP_[device_model_sw_ver].tar.md5)
5.Magisk Manager will patch the entire firmware file and output the newly Patched AP file to [Internal Storage]/Download/magisk_patched.tar
6.Now Copy patched AP file magisk_patched.tar back to Your PC
7.Download latest Odin and extract to Desktop on your PC
Step 2. Installing custom firmware files with Odin
1. Reboot to download mode and select volume up to continue:
2. Open Odin (as administrator) {Right-Mouse click--Open As Administrator}
Select AP in Odin and use the magisk_patched.tar file you have patched {The file you just patched with Magisk} for AP tab of Odin
Select BL,CP and CSC files (Use the files from the firmware you downloaded earlier) (This is VERY important, DON'T just flash only the magisk_patched.tar)
(Use All of the respective files BL, CP, CSC)
3.From Odin option - uncheck Auto Reboot option (I do this because I like rebooting when I'm ready)
4. Make sure all files are in the right place, Now Hit Start and wait till it's completely finish. When It shows PASS in Odin, disconnect device.
Okay Now the hard part is over, you can let the phone boot to system and Skip all Setup Steps because Next is TWRP.
Step 3. Odin: Flash Twrp and Boot with Magisk
Very Simple yet very Important:
1. Download the respective TWRP (Twrp<version_number>.TAR for you phone model (This is going to Odin flashed so you need .TAR file)
2. Reboot your phone into Download Mode, Hold Vol- and Power Button until it gets to DL Screen and press up for "Yes"
3. Put the Twrp<version_number>.TAR in the AP slot
4. Make sure the file is selected, (Unselect Auto-reboot in options tab in Odin) and in place and hit Start
5. Wait until it's finished, Now Hold Vol- and Power until you see black screen, release and then hold Vol+ and Power until you see TWRP recovery
Now Flash Multidisabler and Magisk
1. Flash multidisabler (Mega) (Google Drive) and reboot back to TWRP
2. Wipe data and storage
3. Flash Latest Magisk
*Enjoy
*** Remember: Make a backup of EFS through TWRP and save it to your desktop or Cloud service ie. MEGA, GDrive, Dropbox ****
Please I can't seem to unlock my bootloader because OEM Unlocking functionality is missing on my device. I have tried and still can't find it. Can I root the device without Unlocking the bootloader?
stylemonument said:
Please I can't seem to unlock my bootloader because OEM Unlocking functionality is missing on my device. I have tried and still can't find it. Can I root the device without Unlocking the bootloader?
Click to expand...
Click to collapse
If you could just download and install Telegram app and PM this guy on there (drivel2787)
Please see here: Bootloader Unlock Service For US Variants
BoiBundy said:
If you could just download and install Telegram app and PM this guy on there (drivel2787)
Click to expand...
Click to collapse
Okay.... let me do that. Thanks.
Maybe should include that US Snapdragon will have to get their bootloader unlocked first and how they do..include Telegram. Or your probably going to constantly get the "I can't find OEM unlock" question.
Sent from my SM-N975U using Tapatalk
Msgd re: oem unlock! Btw, if we got any awesome Sam sec experts out there who wouldn’t mind entertaining some qs from me regarding a lot of WEIRD stuff happening w my phone, be eternally grateful. Could even work out a monetary deal for your time, and (perhaps) help!
Thanks much in adv, msg on telegram as @nemotheDreamer.
butchieboy said:
Maybe should include that US Snapdragon will have to get their bootloader unlocked first and how they do..include Telegram. Or your probably going to constantly get the "I can't find OEM unlock" question.
Sent from my SM-N975U using Tapatalk
Click to expand...
Click to collapse
You might be right, I will edit it tonight
So we can legit root the Snapdragon version now?
Nickdroid86 said:
So we can legit root the Snapdragon version now?
Click to expand...
Click to collapse
Yes, it's been going on now for a few months. I've done it myself. It's completely legit
---------- Post added at 09:49 AM ---------- Previous post was at 09:47 AM ----------
Nice Tut BoiBundy, well written.
cerj said:
Yes, it's been going on now for a few months. I've done it myself. It's completely legit
---------- Post added at 09:49 AM ---------- Previous post was at 09:47 AM ----------
Nice Tut BoiBundy, well written.
Click to expand...
Click to collapse
Thanks man, wanted to have a central "fool-proof" way for people to enjoy the freedom of root
Just to be clear - I need to pay to get my bootloader unlocked? That's still the case, right?
MonkeyJug said:
Just to be clear - I need to pay to get my bootloader unlocked? That's still the case, right?
Click to expand...
Click to collapse
Check Here: https://forum.xda-developers.com/t/sampwnd-usa-model-bl-unlock-info-u-u1-w.4201689/
I've been on Nexus and Pixel devices so long now I cannot remember much about modification on Samsung devices. Last one I had rooted was the Note 2. Anyway, bootloader unlocked and successfully rooted my SM-N975U (Note 10+). Now there are updates available so I am sorry if this isn't the place or if a dumb question, but is there any special way I need to do updates on the snapdragon so I don't relock the bootloader or lose root? With Pixel, ADB sideload was easy, not sure with this one.
Is there a multi disabler package that is compatible with the SM-N976V ? I have tried multiple iterations of multidisabler-samsung-2.6c-afaneh92 but am have trouble.
nabnab25658 said:
Is there a multi disabler package that is compatible with the SM-N976V ? I have tried multiple iterations of multidisabler-samsung-2.6c-afaneh92 but am have trouble.
Click to expand...
Click to collapse
I was in the same boat, went to the telegram channel and the guy who made that file added support for 976V. Not sure where else it's available, but you should be able to get it there from Mohammad.
TWRP for S20/N20/TabS7/ZFold2 (Snapdragon)
t.me
Dick_Stickitinski said:
I was in the same boat, went to the telegram channel and the guy who made that file added support for 976V. Not sure where else it's available, but you should be able to get it there from Mohammad.
TWRP for S20/N20/TabS7/ZFold2 (Snapdragon)
t.me
Click to expand...
Click to collapse
Hey, just wanted to thank you for pointing me in the right direction. I've had my Sm-976V BL unlocked and rooted for a bit now, but have been busy hence the late reply.
I have an issue. I boot into TWRP just fine but all my files in sdcard are nothing but random numbers and letters
I think this happens when you don't wipe your data. You also need to flash a decryption file. It happened to me at first because I didn't wipe all data.[/QUOTE]
BoiBundy said:
[28NOV20][Guide] How To ROOT ALL US VER. NOTE 10(+) & Flash TWRP (SnapDragon Only)
Step by Step: How to Root & Flash TWRP on Samsung Galaxy Note 10(+) and Every other Galaxy from S10 and up (SnapDragon Only)
Update: If You Want To Unlock Your Bootloader go here: U.S. Samsung Galaxy Bootloader Unlock Service
So You Figured Out How to Unlock The Bootloader on your Shiny New/Old (Snapdragon) Samsung Galaxy Thing-a-ma-jig
Good on you, but now you want to figure out how to Root properly and enjoy the spoils of said Unlock. Well You've come to right place.
DO NOT QUOTE THE OP PLEASE, (If you would like to place this guide in your respective Device Threads ie. Galaxy s10, s20, s20 Note 20 Ultra 5g etc. thats perfectly fine)
Welcome: Be nice, be courteous and *enjoy
Before you move further, make clear that rooting device -
- Your warranty will be void
- Some of functions may not work on rooted device, some function may get back with unrooting, some functions may never.
- All your data on device will be lost (Factory Reset is in the Instructions below)
- Flashing custom binaries may brick (Usually it's a soft but can be hard brick too), so follow it on your own risk!
Now that you accept the risks, let's have some fun -
Important: Although this is a simple guide you must follow all directions clearly
Simple guide to root your device and install TWRP after unlock: (Thanks to @Krog18 )
1. Download vbmeta_disabled.tar, TWRP for your device, magisk and multidisabler-samsung-2.6-afaneh92
2. Reboot to download mode and flash vbmeta_disabled.tar in ap slot and reboot. Device will reboot to recovery mode prompting you to wipe data so wipe data and reboot to download mode again.
3. Uncheck auto reboot in Odin and flash TWRP in ap slot.
4. Hold volume down and power until the screen goes black then immediately switch to holding volume up, Bixby button (10 series only) and power to reboot into TWRP
5. Flash multidisabler and reboot recovery
6. Go to wipe, format and type yes to format data
7. Flash magisk
8. Make a backup of efs and store it somewhere safe
9. Reboot
*First boot may take 10-15 minutes. If it doesn't boot in 15 minutes, force reboot by holding power and volume down for at least 10 seconds
Additional Method For Rooting If Above method did not work for you:
Step 1 : (Root Base Firmware with Magisk By patching files yourself, Then Flash TWRP in Odin)
Prepare Firmware files for root
You need to Patch AP File to flash using Odin to root device.
1. Download stock firmware for your device ie (SM-N975U/U1, SM-G973U/U1, SM-G975U/U1)
You need to download file according your region and model.
2. Once you finish download, extract files and keep all files on in a folder on the desktop of PC. From extracted files find the file with name AP_[device_model_sw_ver].tar.md5 copy to your Phone.
3.Download Latest Magisk Manager and Install to your device (Make sure to check for updates) (Optionally go into settings and switch the update channel to BETA)
4.Open Magisk Manager - Find Magisk Install (Top One) - Click Install - select to "Select and Patch file" - Click the AP file you have copied to your device (AP_[device_model_sw_ver].tar.md5)
5.Magisk Manager will patch the entire firmware file and output the newly Patched AP file to [Internal Storage]/Download/magisk_patched.tar
6.Now Copy patched AP file magisk_patched.tar back to Your PC
7.Download latest Odin and extract to Desktop on your PC
Step 2. Installing custom firmware files with Odin
1. Reboot to download mode and select volume up to continue:
2. Open Odin (as administrator) {Right-Mouse click--Open As Administrator}
Select AP in Odin and use the magisk_patched.tar file you have patched {The file you just patched with Magisk} for AP tab of Odin
Select BL,CP and CSC files (Use the files from the firmware you downloaded earlier) (This is VERY important, DON'T just flash only the magisk_patched.tar)
(Use All of the respective files BL, CP, CSC)
3.From Odin option - uncheck Auto Reboot option (I do this because I like rebooting when I'm ready)
4. Make sure all files are in the right place, Now Hit Start and wait till it's completely finish. When It shows PASS in Odin, disconnect device.
Okay Now the hard part is over, you can let the phone boot to system and Skip all Setup Steps because Next is TWRP.
Step 3. Odin: Flash Twrp and Boot with Magisk
Very Simple yet very Important:
1. Download the respective TWRP (Twrp<version_number>.TAR for you phone model (This is going to Odin flashed so you need .TAR file)
2. Reboot your phone into Download Mode, Hold Vol- and Power Button until it gets to DL Screen and press up for "Yes"
3. Put the Twrp<version_number>.TAR in the AP slot
4. Make sure the file is selected, (Unselect Auto-reboot in options tab in Odin) and in place and hit Start
5. Wait until it's finished, Now Hold Vol- and Power until you see black screen, release and then hold Vol+ and Power until you see TWRP recovery
Now Flash Multidisabler and Magisk
1. Flash multidisabler (Mega) (Google Drive) and reboot back to TWRP
2. Wipe data and storage
3. Flash Latest Magisk
*Enjoy
*** Remember: Make a backup of EFS through TWRP and save it to your desktop or Cloud service ie. MEGA, GDrive, Dropbox ****
Click to expand...
Click to collapse
which TWRP version to flash and which odin? hope i can get answer i had N975U1 unlocked bootloader
Anyone else getting that pesky "Android 11 Update" since they have rooted? I keep postponing it. I'm guessing it will fail if I try to install. Not sure what I should do.
Sammobile don't seem to have the firmware available yet. I was thinking installing it with odin then patching AP with Magisk
BoiBundy said:
[28NOV20][Guide] How To ROOT ALL US VER. NOTE 10(+) & Flash TWRP (SnapDragon Only)
Step by Step: How to Root & Flash TWRP on Samsung Galaxy Note 10(+) and Every other Galaxy from S10 and up (SnapDragon Only)
Update: If You Want To Unlock Your Bootloader go here: U.S. Samsung Galaxy Bootloader Unlock Service
So You Figured Out How to Unlock The Bootloader on your Shiny New/Old (Snapdragon) Samsung Galaxy Thing-a-ma-jig
Good on you, but now you want to figure out how to Root properly and enjoy the spoils of said Unlock. Well You've come to right place.
DO NOT QUOTE THE OP PLEASE, (If you would like to place this guide in your respective Device Threads ie. Galaxy s10, s20, s20 Note 20 Ultra 5g etc. thats perfectly fine)
Welcome: Be nice, be courteous and *enjoy
Before you move further, make clear that rooting device -
- Your warranty will be void
- Some of functions may not work on rooted device, some function may get back with unrooting, some functions may never.
- All your data on device will be lost (Factory Reset is in the Instructions below)
- Flashing custom binaries may brick (Usually it's a soft but can be hard brick too), so follow it on your own risk!
Now that you accept the risks, let's have some fun -
Important: Although this is a simple guide you must follow all directions clearly
Simple guide to root your device and install TWRP after unlock: (Thanks to @Krog18 )
1. Download vbmeta_disabled.tar, TWRP for your device, magisk and multidisabler-samsung-2.6-afaneh92
2. Reboot to download mode and flash vbmeta_disabled.tar in ap slot and reboot. Device will reboot to recovery mode prompting you to wipe data so wipe data and reboot to download mode again.
3. Uncheck auto reboot in Odin and flash TWRP in ap slot.
4. Hold volume down and power until the screen goes black then immediately switch to holding volume up, Bixby button (10 series only) and power to reboot into TWRP
5. Flash multidisabler and reboot recovery
6. Go to wipe, format and type yes to format data
7. Flash magisk
8. Make a backup of efs and store it somewhere safe
9. Reboot
*First boot may take 10-15 minutes. If it doesn't boot in 15 minutes, force reboot by holding power and volume down for at least 10 seconds
Additional Method For Rooting If Above method did not work for you:
Step 1 : (Root Base Firmware with Magisk By patching files yourself, Then Flash TWRP in Odin)
Prepare Firmware files for root
You need to Patch AP File to flash using Odin to root device.
1. Download stock firmware for your device ie (SM-N975U/U1, SM-G973U/U1, SM-G975U/U1)
You need to download file according your region and model.
2. Once you finish download, extract files and keep all files on in a folder on the desktop of PC. From extracted files find the file with name AP_[device_model_sw_ver].tar.md5 copy to your Phone.
3.Download Latest Magisk Manager and Install to your device (Make sure to check for updates) (Optionally go into settings and switch the update channel to BETA)
4.Open Magisk Manager - Find Magisk Install (Top One) - Click Install - select to "Select and Patch file" - Click the AP file you have copied to your device (AP_[device_model_sw_ver].tar.md5)
5.Magisk Manager will patch the entire firmware file and output the newly Patched AP file to [Internal Storage]/Download/magisk_patched.tar
6.Now Copy patched AP file magisk_patched.tar back to Your PC
7.Download latest Odin and extract to Desktop on your PC
Step 2. Installing custom firmware files with Odin
1. Reboot to download mode and select volume up to continue:
2. Open Odin (as administrator) {Right-Mouse click--Open As Administrator}
Select AP in Odin and use the magisk_patched.tar file you have patched {The file you just patched with Magisk} for AP tab of Odin
Select BL,CP and CSC files (Use the files from the firmware you downloaded earlier) (This is VERY important, DON'T just flash only the magisk_patched.tar)
(Use All of the respective files BL, CP, CSC)
3.From Odin option - uncheck Auto Reboot option (I do this because I like rebooting when I'm ready)
4. Make sure all files are in the right place, Now Hit Start and wait till it's completely finish. When It shows PASS in Odin, disconnect device.
Okay Now the hard part is over, you can let the phone boot to system and Skip all Setup Steps because Next is TWRP.
Step 3. Odin: Flash Twrp and Boot with Magisk
Very Simple yet very Important:
1. Download the respective TWRP (Twrp<version_number>.TAR for you phone model (This is going to Odin flashed so you need .TAR file)
2. Reboot your phone into Download Mode, Hold Vol- and Power Button until it gets to DL Screen and press up for "Yes"
3. Put the Twrp<version_number>.TAR in the AP slot
4. Make sure the file is selected, (Unselect Auto-reboot in options tab in Odin) and in place and hit Start
5. Wait until it's finished, Now Hold Vol- and Power until you see black screen, release and then hold Vol+ and Power until you see TWRP recovery
Now Flash Multidisabler and Magisk
1. Flash multidisabler (Mega) (Google Drive) and reboot back to TWRP
2. Wipe data and storage
3. Flash Latest Magisk
*Enjoy
*** Remember: Make a backup of EFS through TWRP and save it to your desktop or Cloud service ie. MEGA, GDrive, Dropbox ****
Click to expand...
Click to collapse
it works on my N975U1 android 10 Q version 1st method so no need 2nd method