Have I bricked my FTV 4K stick beyond repair? - Fire TV Q&A, Help & Troubleshooting

Sorry if this is posted in the wrong section, I am never quite sure where these sort of queries should go
To cut a long story short I unlocked and rooted 1 of my FTV 4K sticks, I was struggling with an issue on 1 and ended up installing a Magisk update. I know there are warning all over the forum about this please put it down to a lack of experience.
On reboot it just comes up with the black screen and the white amazon logo, it stays on this for about 2 minutes then restarts to the same black screen. i.e. its caught in a boot loop. It never gets to the white amazon screen.
I bought myself an OTG cable thinking this would get me to twrp so I could go into recovery and wipe it and start again or something, but even with the OTG cable plugged in it still does exactly the same thing. I have tried the same OTG cable and entertainment keyboard setup on another FTV 4K stick and it gives me the 5 second boot menu to get into recovery.
I am guessing I have killed it beyond repair? Is there anything else I can try to do?
Thanks

you need a usb keyboard and then you need to press a combination shown on youtube: , Don't be afraid it is very hard to do it but i can confirm it works 100% for sure!! The timing for holding the key press is all that matters to be successfully...
Try different timings if it's not working on the first run but you need then to hold the buttons for very long time until your fingers feel dead....
..im not sure if adb is working in "safe mode" you need to test that. If yes - you could use "adb reboot recovery".
2. you need to reflash Magisk in core mode.

Aq
dougie175 said:
Sorry if this is posted in the wrong section, I am never quite sure where these sort of queries should go
To cut a long story short I unlocked and rooted 1 of my FTV 4K sticks, I was struggling with an issue on 1 and ended up installing a Magisk update. I know there are warning all over the forum about this please put it down to a lack of experience.
On reboot it just comes up with the black screen and the white amazon logo, it stays on this for about 2 minutes then restarts to the same black screen. i.e. its caught in a boot loop. It never gets to the white amazon screen.
I bought myself an OTG cable thinking this would get me to twrp so I could go into recovery and wipe it and start again or something, but even with the OTG cable plugged in it still does exactly the same thing. I have tried the same OTG cable and entertainment keyboard setup on another FTV 4K stick and it gives me the 5 second boot menu to get into recovery.
I am guessing I have killed it beyond repair? Is there anything else I can try to do?
Thanks
Click to expand...
Click to collapse
You haven't killed your stick, install fastboot drivers and app.
Connect your stick to your pc via usb.
Enter
Code:
fastboot devices
when you see black screen with amazon logo, it should be inside fastboot mode
(If somehow you flashed update to boot.img as written in the guide)
If you see the stick in fastboot mode,
Pull twrp from kamakiri.zip
Place it in fastboot folder
Enter
Code:
fastboot flash boot boot.img
(boot.img or whatever the name of your twrp image)
Code:
fastboot reboot recovery
It should work, if not you can use shorting method again.

Thanks very much both, I will have a play around this evening when I get home from work and the kids are in bed, hopefully with the info above I can get back to recovery again.

Thanks for the help gents, in the end I had to do the shorting method to get the stick to do anything. It took about 6 attempts before kamakiri script even registered it as anything being plugged in, it just kept saying wait for boot.
Once it realised the stick was present and shorted I was away though, I have ended up having to factory reset and wipe everything so will need to start again with it but I am just pleased I don’t need to shell out again for a new stick.
Thanks again for your help

Related

[Q] Hard-Bricked Dropped Kindle Fire

TL;DR: Dropped Kindle Fire won't boot to OS or recovery, even after flashing FFF and "successfully" flashing TWRP. Broken flash chip?
More Info:
My brother gave me a non-functioning Kindle Fire from a friend of his. (FYI, I do not believe it to be stolen). When I got it, it would turn on to a static Kindle Fire logo for about a second, then the screen would get a little brighter, then go completely dead.
After derping around trying to get it to boot or be recognized (to no avail), I followed these instructions (USB boot shorting trick) to get into USB boot mode, then these instructions (Firekit bootloader and recovery installation utility) to install FFF and TWRP while the Kindle was in USB mode. Now, it boots to the yellow fire triangle, but after 10-20 seconds, it still gets a little brighter and then dies. NBD, I haven't installed a new ROM yet. However, if I press the power button again to get into recovery, the button goes orange, but then the screen gets brighter and dies again. Same happens when I try to fastboot into recovery. Firekit says sending, writing, loading, and booting recovery all worked, but the above continues to happen.
The device looks like it has been dropped; the glass on the lower edge of the screen is cracked, and it is generally scuffed and scratched around the edge. There is no visible damage to the motherboard or any components (no cracking, etc.). But these symptoms look to me like a bad flash chip. Any other thoughts?
deutschigmann said:
TL;DR: Dropped Kindle Fire won't boot to OS or recovery, even after flashing FFF and "successfully" flashing TWRP. Broken flash chip?
More Info:
My brother gave me a non-functioning Kindle Fire from a friend of his. (FYI, I do not believe it to be stolen). When I got it, it would turn on to a static Kindle Fire logo for about a second, then the screen would get a little brighter, then go completely dead.
After derping around trying to get it to boot or be recognized (to no avail), I followed these instructions (USB boot shorting trick) to get into USB boot mode, then these instructions (Firekit bootloader and recovery installation utility) to install FFF and TWRP while the Kindle was in USB mode. Now, it boots to the yellow fire triangle, but after 10-20 seconds, it still gets a little brighter and then dies. NBD, I haven't installed a new ROM yet. However, if I press the power button again to get into recovery, the button goes orange, but then the screen gets brighter and dies again. Same happens when I try to fastboot into recovery. Firekit says sending, writing, loading, and booting recovery all worked, but the above continues to happen.
The device looks like it has been dropped; the glass on the lower edge of the screen is cracked, and it is generally scuffed and scratched around the edge. There is no visible damage to the motherboard or any components (no cracking, etc.). But these symptoms look to me like a bad flash chip. Any other thoughts?
Click to expand...
Click to collapse
The battery may be low... Try using the factory charger (not USB).
If that doesn't work, let me know. This sounds like an issue a lot of people are having, and maybe I could work something out with you so I can get a failing KF to debug.
Also which command did you use in firekit? Try again with usb_fix_parts_and_install_fff_twrp. You may have a screwed up partition table. Since the LED changes color and the screen comes on, your first stage boot loader should be working.
pokey9000 said:
The battery may be low... Try using the factory charger (not USB).
If that doesn't work, let me know. This sounds like an issue a lot of people are having, and maybe I could work something out with you so I can get a failing KF to debug.
Click to expand...
Click to collapse
We've had it plugged into a charger for a Samsung smartphone. I wasn't given an actual KF charger. Right now it's plugged into my iPad charger, which is closer to the KF charger output, but it's still USB. I'll leave it there for a bit and let you know what happens. I don't think it's a battery issue because it's had enough power to do this on/off cycle numerous times, but who knows. When plugged in, it does it again, dies, and makes no indication that it is charging or anything, just like it does with a PC. I have a multimeter, so I could check the voltage/amperage across the battery, but I don't know which wires to do lol.
pokey9000 said:
Also which command did you use in firekit? Try again with usb_fix_parts_and_install_fff_twrp. You may have a screwed up partition table. Since the LED changes color and the screen comes on, your first stage boot loader should be working.
Click to expand...
Click to collapse
I started with usb_fix_parts_and_install_fff_twrp, and then tried usb_boot_twrp, then some of the fastboot commands. I think they all said they worked at each step. The boot command always said something like 0.003 s, not sure if that is a normal time.
It's been plugged into the iPad charger for a few hours now, and the behavior has not changed.
deutschigmann said:
We've had it plugged into a charger for a Samsung smartphone. I wasn't given an actual KF charger. Right now it's plugged into my iPad charger, which is closer to the KF charger output, but it's still USB. I'll leave it there for a bit and let you know what happens. I don't think it's a battery issue because it's had enough power to do this on/off cycle numerous times, but who knows. When plugged in, it does it again, dies, and makes no indication that it is charging or anything, just like it does with a PC. I have a multimeter, so I could check the voltage/amperage across the battery, but I don't know which wires to do lol.
Click to expand...
Click to collapse
Yeah, it was a crapshoot, but a few people have had some weirdnesses resolved by making sure the battery's charged. I guess the fact that you get through the TWRP install rules this out.
I started with usb_fix_parts_and_install_fff_twrp, and then tried usb_boot_twrp, then some of the fastboot commands. I think they all said they worked at each step. The boot command always said something like 0.003 s, not sure if that is a normal time.
Click to expand...
Click to collapse
One theory I've had is that either something is being missed by the partition recreator, or there's some assumption that the emmc is blanked when the device is initially flashed. If you have no attachments to any data that might be on this Fire, you could try zeroing (or 0xFFing as erased flash would be) the flash while in TWRP (via adb). Then redo the usb_fix_parts_blah_blah which should leave you with bootloaders and recovery.
I'm not sure if this would work, but without knowing where and why the bootloader is dying I can only guess.
I just erased each partition through fastboot (fastboot erase boot, system, cache, userdata, recovery) and it seemed to work, or at least think it was working, as they each took a proportional amount of time from 2 s for boot to 118 s for userdata. Ran install_fff_twrp, it went through all the motions, then died when it tried to boot as before. Tried using the power button to get to TWRP, same thing.
Edit: Just found a list of the partitions. Went through in fastboot and deleted xloader, bootloader, dkernel, dfs, recovery, backup, boot, splash, system, userdata, cache, and media. Reran install_fff_twrp, same effect as before. Oh whoops, now it won't boot at all. Probably need to do the shorting trick again.
Hmm, I may have borked it a bit more than I intended. Right now, doing the USB trick, running usb_fix_parts... it says:
Loading FFF through USB...
?
waiting for OMAP44xx device...
I let it sit, then Ctrl+C, redid, tried again, hung after "?" and seemed unwilling to Ctrl+C, redid, hung at "waiting" again.
Edit: Did it one more time, seems to have worked (as well as earlier). Hung for a while on "Resetting bootmode to standard boot...", but it said it only took 0.079 s. Whatever the case all steps said "OKAY" and the screen got brighter, then all went dead.
Is there a way to do a full wipe of the disk through fastboot, other than doing partition-by-partition?
OK so it looks like the weird hangings and stuff were probably due to using a-port USB extender on my laptop. Tried on my desktop and everything went quickly, but the KF still died.
After all the deletions and stuff it still won't boot into recovery, but instead of dying when trying to do a normal boot, it just gets hung on the bootloader screen, and won't allow me to try to go into recovery. I'm not sure if that's better or worse. I guess it means the deletions really erased something, but then why won't it write/boot?
deutschigmann said:
Hmm, I may have borked it a bit more than I intended. Right now, doing the USB trick, running usb_fix_parts... it says:
Loading FFF through USB...
?
waiting for OMAP44xx device...
I let it sit, then Ctrl+C, redid, tried again, hung after "?" and seemed unwilling to Ctrl+C, redid, hung at "waiting" again.
Edit: Did it one more time, seems to have worked (as well as earlier). Hung for a while on "Resetting bootmode to standard boot...", but it said it only took 0.079 s. Whatever the case all steps said "OKAY" and the screen got brighter, then all went dead.
Is there a way to do a full wipe of the disk through fastboot, other than doing partition-by-partition?
Click to expand...
Click to collapse
Can you still get into TWRP after the usb_fix_parts... finishes? If so, try:
adb shell
When you get a prompt, do:
tr "\000" "\377" < /dev/zero | dd of=/dev/block/mmcblk0
***WARNING THIS COMMAND WILL STEAL YOUR CAR AND USE YOUR
***CUPHOLDERS FOR A URINAL. IT WISHES YOUR FAMILY ILL AND IS
***RESPONSIBLE FOR PUTTING INDUSTRIAL WASTE IN IMPORTED PET
***FOOD. IT IS SERIOUS BUSINESS. DON'T DO THIS UNLESS YOU
***ABSOLUTELY KNOW WHAT YOU'RE DOING.
It might take a few hours for this to run. At the end your flash will be fresh from the factory clean. If you hold down the power button long enough, your Fire should go into USB boot mode regardless of shorting the test point. Now try the usb_fix_parts_... again.
I wish I could, but I've never been able to get it into recovery. Just bootloader.
deutschigmann said:
I wish I could, but I've never been able to get it into recovery. Just bootloader.
Click to expand...
Click to collapse
So when you run usb_fix_parts_and_install_fff_twrp, it doesn't reboot into TWRP when it's done? You don't have to get it to run recovery from the flash, just run recovery at all. Unfortunately FFF doesn't know how to wipe everything at the level I described.
No, it says it does each step and gives the status OKAY, but when it tries to boot the recovery, the screen gets a little brigher and then everything dies, just like when I try to get to it using the power button.
deutschigmann said:
No, it says it does each step and gives the status OKAY, but when it tries to boot the recovery, the screen gets a little brigher and then everything dies, just like when I try to get to it using the power button.
Click to expand...
Click to collapse
Does "usb_boot_twrp" work instead of usb_fix_parts...?
Nope, same result. Gets brighter, dies. Hmm...
Tried another copy of TWRP and ./fastboot boot twrp....img, same thing. Flashed TWRP 2.1.1 from another post, still dies.
Is it possible to boot to USB storage, similar to the other USB boot trick? So that I could use the linux distro's system to write to the disk?
deutschigmann said:
Is it possible to boot to USB storage, similar to the other USB boot trick? So that I could use the linux distro's system to write to the disk?
Click to expand...
Click to collapse
No, unfortunately. The USB boot is part of the on-chip bootrom. It's not smart enough to do much more than boot off SD & soldered down flash chips, serial, and the simple USB device protocol.
What's making this hard is not being able to see where it's dying: is it in the kernel or in FFF? It seems like your Fire is now in the same state as everyone who was bitten by the latest CWM.
Since it had the same behavior before and after installing FFF, I feel like that's probably not it. It seemed like it likely hadn't been modded before, since it was stuck on the stock KF logo.
pokey plz make it working again the kindle is still in waiting for device
hey plz solve the firekit issue of being stuck in waiting for device issu

[Q] Need Help - Bricked Kindle Fire

I got this kindle fire that I am trying to fix for my kid. I don't know what firmware was in. The KF has never been rooted. We tried to call Amazon for a replacement, but since I didn't remember which email account was tied to this KF and I couldn't find the Serial Number either, I got stuck with it. If could make this device to boot one more time to see the amazon account or the serial number that will be great.
Well anyways, these are the symptoms. After lots of hours of reading about bricked Kindle Fires I decided to order a factory cable suspecting the problem was a low battery KF going into a 5 second loop. The process went good. I was able to flash FFF 1.4a and TWRP 2.2.2.1 by going into fastboot mode, but the problem is that the KF does not want to start in recovery mode, nor in normal mode.
At this point, I think I can rule out a battery low problem, but I am not sure.
No matter what I do, I cannot enter to adb mode, and this is the real problem I don't seem to find an answer. If there was a way that I could upload the firmware from fastboot mode or a tool that forces recovery mode.
As I said this KF was always stock until today that I tried to unbrick it by installing the FFF and the TWRP. The TWRP never started.
As I said earlier my only objective at this point is to recover the serial number or the account email associated with my KF.
Question 2, how can I revert to the stock bootloader if everything else fails?
Any suggestions, links, ideas will be welcome.
gwmadrigal said:
I got this kindle fire that I am trying to fix for my kid. I don't know what firmware was in. The KF has never been rooted. We tried to call Amazon for a replacement, but since I didn't remember which email account was tied to this KF and I couldn't find the Serial Number either, I got stuck with it. If could make this device to boot one more time to see the amazon account or the serial number that will be great.
Well anyways, these are the symptoms. After lots of hours of reading about bricked Kindle Fires I decided to order a factory cable suspecting the problem was a low battery KF going into a 5 second loop. The process went good. I was able to flash FFF 1.4a and TWRP 2.2.2.1 by going into fastboot mode, but the problem is that the KF does not want to start in recovery mode, nor in normal mode.
At this point, I think I can rule out a battery low problem, but I am not sure.
No matter what I do, I cannot enter to adb mode, and this is the real problem I don't seem to find an answer. If there was a way that I could upload the firmware from fastboot mode or a tool that forces recovery mode.
As I said this KF was always stock until today that I tried to unbrick it by installing the FFF and the TWRP. The TWRP never started.
As I said earlier my only objective at this point is to recover the serial number or the account email associated with my KF.
Question 2, how can I revert to the stock bootloader if everything else fails?
Any suggestions, links, ideas will be welcome.
Click to expand...
Click to collapse
I hate to ask this question but do you know how to access recovery by using the power button to get the boot menu then selecting recovery? If you are using the boot menu to attempt to access recovery and its not cooperating it`s possible that points to a broken bootloader or a broken recovery. When you flashed both fff and twrp did you see that it sent and physically wrote each one? maybe explain how you flashed them so we can see if a error was made there. What level do you believe the battery is at? Possible it could be playing a role in your present issue.
Thepooch said:
I hate to ask this question but do you know how to access recovery by using the power button to get the boot menu then selecting recovery? If you are using the boot menu to attempt to access recovery and its not cooperating it`s possible that points to a broken bootloader or a broken recovery. When you flashed both fff and twrp did you see that it sent and physically wrote each one? maybe explain how you flashed them so we can see if a error was made there. What level do you believe the battery is at? Possible it could be playing a role in your present issue.
Click to expand...
Click to collapse
I have done a lot of experiments with my SGS2 about installing ROMS using ODIN or CWR, backing up my own images and making backups. Most of the work I do though is in CWR. I haven't dealt with TWR yet. I also installed ICS on my HP Touchpad. So, even though this is the first time I deal with the KF, I already some experience working with ROMS and images.
Back to the process. I installed the FFF using the Kindle Fire Utility. The KF was forced to fastboot mode via the factory cable. At first I could see on the KF splash screen with the black and orange logo, and now the KF is booting using a Black and Blue kindle fire logo with 1.4a on top. At the bottom of the splash I see instructions of the bootloader selector indicating to press the power button and select the mode that I want to boot. Either Normal Mode or Recovery Mode.
I flashed the TWRP 2.2.2.1 in fastboot mode using my command prompt by putting this code:
Code:
fastboot -i 0x1949 flash recovery [path]\openrecovery-twrp-2.2.2.1-blaze.img
I was following the instructions on this guide.
http://forum.xda-developers.com/showthread.php?t=1638452
I got stuck on step 3 after attempting to boot into recovery mode.
I can select which boot mode I want to go, but none of them work. I only get on the bottom of the screen saying Booting... and then the KF shuts down.
I suspect the battery had a good level of charge, but I can't tell for sure.
Thanks for everything.
Download TWRP again, check the md5, reinstall, and post whatever error messages (if any) that are in your command window here.
In the meantime, enter the following command and let me know what happens after you reboot.
Code:
fastboot oem idme bootmode 5001
fastboot reboot
soupmagnet said:
Download TWRP again, check the md5, reinstall, and post whatever error messages (if any) that are in your command window here.
In the meantime, enter the following command and let me know what happens after you reboot.
Code:
fastboot oem idme bootmode 5001
fastboot reboot
Click to expand...
Click to collapse
All commands were successful.
When I'm doing instead of the fastboot reboot is to remove the factory cable. Shutdown the KF by holding the power button. Then I connect a regular USB cable. The KF starts the boot process. It enters the first splash screen. Then it moves to booting, but the booting fails. The only thing that I see is that the button light turns from green to yellow and then it shuts down. And the boot process starts again going into a boot loop.
gwmadrigal said:
All commands were successful.
When I'm doing instead of the fastboot reboot is to remove the factory cable. Shutdown the KF by holding the power button. Then I connect a regular USB cable. The KF starts the boot process. It enters the first splash screen. Then it moves to booting, but the booting fails. The only thing that I see is that the button light turns from green to yellow and then it shuts down. And the boot process starts again going into a boot loop.
Click to expand...
Click to collapse
What happens when you change the bootmode to 5001?
soupmagnet said:
What happens when you change the bootmode to 5001?
Click to expand...
Click to collapse
It accepts the command.
The command prompt responds saying something like it took 0. something seconds to execute the command.
Thanks for reading my thread.
If upon rebooting, the result is the same after changing the bootmode, it is possible the bootloader isn't working properly. If that's the case, flashing a new bootloader (with md5 verified) might not work, but it's worth a shot.
If that doesn't work, you should be able to change the bootmode to USBboot (4003) and use Firekit to replace the bootloader, but that's speaking theoretically. I've never tried it so I couldn't tell you whether it would work or not. But then you could always pull the back cover off the device and use the shorting trick to use Firekit in USBboot.
If installing a bootloader with the Firekit doesn't work, you're likely looking at a hardware issue, and there's not much we can do about that.
soupmagnet said:
1. If upon rebooting, the result is the same after changing the bootmode, it is possible the bootloader isn't working properly. If that's the case, flashing a new bootloader (with md5 verified) might not work, but it's worth a shot.
2. If that doesn't work, you should be able to change the bootmode to USBboot (4003) and use Firekit to replace the bootloader, but that's speaking theoretically. I've never tried it so I couldn't tell you whether it would work or not. But then you could always pull the back cover off the device and use the shorting trick to use Firekit in USBboot.
3. If installing a bootloader with the Firekit doesn't work, you're likely looking at a hardware issue, and there's not much we can do about that.
Click to expand...
Click to collapse
2 sounds too complicated. I will need to read more.
I'm at work. I am going to try number 1 when I get home.
One more question, how can I revert the KF so when the it boots it shows the original orange white logo?
Thanks for everything.
gwmadrigal said:
2 sounds too complicated. I will need to read more.
I'm at work. I am going to try number 1 when I get home.
One more question, how can I revert the KF so when the it boots it shows the original orange white logo?
Thanks for everything.
Click to expand...
Click to collapse
If you have any questions about using Firekit, don't be afraid to ask.
Get your device working properly before attempting to revert the bootloader back to stock. Contrary to what you may think, the custom bootloader is much better for you in this situation.
gwmadrigal said:
All commands were successful.
When I'm doing instead of the fastboot reboot is to remove the factory cable. Shutdown the KF by holding the power button. Then I connect a regular USB cable. The KF starts the boot process. It enters the first splash screen. Then it moves to booting, but the booting fails. The only thing that I see is that the button light turns from green to yellow and then it shuts down. And the boot process starts again going into a boot loop.
Click to expand...
Click to collapse
I suspect your battery is still depleted because it still sounds like a 5 second boot loop. Try this hold the power button down till it`s off and plug it to your pc for a few hours to see if you cannot get some power to your battery.
Thepooch said:
I suspect your battery is still depleted because it still sounds like a 5 second boot loop. Try this hold the power button down till it`s off and plug it to your pc for a few hours to see if you cannot get some power to your battery.
Click to expand...
Click to collapse
I think that would be the case if the device just rebooted. The OP is saying the device shuts down when FFF starts to load the operating system (Booting...) or recovery, which is why I think it is either the bootloader or some hardware issue.
soupmagnet said:
If you have any questions about using Firekit, don't be afraid to ask.
Get your device working properly before attempting to revert the bootloader back to stock. Contrary to what you may think, the custom bootloader is much better for you in this situation.
Click to expand...
Click to collapse
I tried reloading the u-boot using fastboot and the upload was successful. But it's doing exactly the same.I guess my only question right now, do you know of any good guide that I should start reading to get my feet wet on what the firekit is and how to get started?
Thepooch said:
I suspect your battery is still depleted because it still sounds like a 5 second boot loop. Try this hold the power button down till it`s off and plug it to your pc for a few hours to see if you cannot get some power to your battery.
Click to expand...
Click to collapse
I have nothing to lose. This KF is already bricked. I can certainly try anything. Which cable do you suggest I use? the Factory cable or the USB cable?
I think I answered my own question now. Using a regular USB cable puts the KF in the bootloop. I will use the factory cable instead. I shut down the KF, put the factory cable connected to my computer and the KF. Right now the KF is in the KindleFire splash screen waiting for fastboot commands of for me to use the button to tell it which mode to boot. I will leave it plug overnight.
Thanks for replying on my thread and trying to help me.
soupmagnet said:
I think that would be the case if the device just rebooted. The OP is saying the device shuts down when FFF starts to load the operating system (Booting...) or recovery, which is why I think it is either the bootloader or some hardware issue.
Click to expand...
Click to collapse
I posted a video in utube of what the KF is doing, so you can see what I'm seeing.
Link
Thanks for coming back several times to reply on my thread.
That looks like your battery. From what I can tell, the device is just rebooting, not shutting down.
Unplug the device and hold the power button to perform a hard shutdown.
Plug the device in (it should power up on it's own) and hold the power button to shut it down again.
Leave it plugged into the computer until sometime tomorrow and try again.
Same thing I was thinking 5 second bootloop Thank you the video was very helpful to see just how its acting. Use stock cable to charge not factory.
OKay. I'm glad I came to check the thread one more time before going to bed. I removed the factory cable and put the regular usb instead. The KF was rebooting. I shut down the KF by holding the power button without unplugging the cable. Now the KF appears to be shut down, but the cable is still plugged. The yellow light does not appear as it normally would if it was charging though. I don't know if this is normal.
gwmadrigal said:
OKay. I'm glad I came to check the thread one more time before going to bed. I removed the factory cable and put the regular usb instead. The KF was rebooting. I shut down the KF by holding the power button without unplugging the cable. Now the KF appears to be shut down, but the cable is still plugged. The yellow light does not appear as it normally would if it was charging though. I don't know if this is normal.
Click to expand...
Click to collapse
I think you're fine let it rest.

[Q] Kindle Fire 2 brick: WHITE triangle on boot

Right, so, I've done some googling and some searching about here and there but either I'm being dense and the solution is really simple, or nobody's done what I've done with this tablet before and, again, I'm being dense. Here's my issue:
Kindle Fire 2 (2nd gen, also second-hand) tablet: stock, rooted, that worked fine with the tool by bin4ry.
Rebooted after that, verified root was working, adb and fastboot perfectly fine (sidenote: linux user, no shonky Windows drivers at fault here)
My ultimate goal is to get CM on this device, so, started after this to follow the instructions in this thread regarding getting the second bootloader on the tablet.
Realised I need a factory cable, ordered, delivered, works but not all the time, I'm not sure if it's a dodgy cable or not but did get into fastboot.
Got new bootloader installed, saw Kindle Fire logo in blue. Proceeded to boot the stock rom after this and use adb push to put the CM 11 zip and the gapps zip files on /sdcard.
adb shell, su, reboot recovery, intending to boot into TWRP to flash new rom
Tablet reboots, but is now stuck with the stock boot logo (orange) and then a black screen with a white triangle and exclamation mark on it. I haven't seen any references to this particular delight.
Fastboot cable does not, no matter how I fiddle with it, put the tablet in fastboot mode. Holding down the power button for five minutes did nothing.
I've read that if it turns on, it can probably be recovered, but I don't know what to do from here. Can anyone render assistance?
So, after much fiddling, I discovered that my problem was actually that my fastboot cable was loose in the microUSB end, and not contacting properly with the pins - thus not sending the tablet the requisite signal to enter fastboot mode.
I've successfully got TWRP onto the fire and thus CM 10.1 now.
I hope this update helps anyone who finds themselves in a similar situation; fastboot still works, keep wiggling.
xyonofcalhoun said:
So, after much fiddling, I discovered that my problem was actually that my fastboot cable was loose in the microUSB end, and not contacting properly with the pins - thus not sending the tablet the requisite signal to enter fastboot mode.
I've successfully got TWRP onto the fire and thus CM 10.1 now.
I hope this update helps anyone who finds themselves in a similar situation; fastboot still works, keep wiggling.
Click to expand...
Click to collapse
I had this problem with a 2nd gen Kindle that was also second hand.
Phoned Amazon UK, described the problem (not mentioning I'd done it myself) and they replaced it.
Seems there's not a lot they won't replace.

Bricked my Fire TV Stick 1?

Hi there!
I think I may have bricked my Fire TV Stick 1 (bought at launch in Germany)...
Current situation:
- stick turns on, shows white amazon logo on black background
- continuously rebooting; ~5s black screen, ~5s amazon logo
After months not having it used, I found out I may be able to root it by now. So I did research over the vast amount of threads and posts and was overwhelmed by the information... So I tried to get started but struggled to find the right steps and therefore maybe failed.
I updated it to 5.0.5 (stock) and tried King Root, then Kingo Root, which was a success.
I tried to use the TWRP 3.0.0-7 v2 zip and used the sh command from the respective thread (I thought that was it, since all my devices before used either TWRP or CWM).
To this point, all went through and I wanted to reboot into recovery, but there was only this generic (stock?) red text recovery screen. I waited to be sure, nothing happened and I unplugged it to reboot.
It booted fine and I reflashed the TWRP zip, in case I didn't do it properly. Again it did as expected.
I then pushed the latest prerooted 5.2.0.1 zip and rebooted to recovery, but again this generic screen, so I unplugged it early, I think.
From there on, I got stuck at the white amazon logo, see above.
I did not unlock the bootloader, adb shell confirmed it not being unlocked before.
During bootloops, I did not manage to get any control via adb or fastboot.
So, is it bricked once and for all? If not, how can I save it?
I don't care about anything stored on it.
I also have a Y-USB-OTG cable and connected a keyboard before, but could not interfere yet.
(If bricked, would a Teensy be of any use? I have one from CCast rooting days)
Thanks for reading and in advance.
I had same problem with my fire stick when used the USB power of my TV.
Did you try to power the fire stick TV with the power point and USB adapter?
l_aios said:
Hi there!
I think I may have bricked my Fire TV Stick 1 (bought at launch in Germany)...
Current situation:
- stick turns on, shows white amazon logo on black background
- continuously rebooting; ~5s black screen, ~5s amazon logo
After months not having it used, I found out I may be able to root it by now. So I did research over the vast amount of threads and posts and was overwhelmed by the information... So I tried to get started but struggled to find the right steps and therefore maybe failed.
I updated it to 5.0.5 (stock) and tried King Root, then Kingo Root, which was a success.
I tried to use the TWRP 3.0.0-7 v2 zip and used the sh command from the respective thread (I thought that was it, since all my devices before used either TWRP or CWM).
To this point, all went through and I wanted to reboot into recovery, but there was only this generic (stock?) red text recovery screen. I waited to be sure, nothing happened and I unplugged it to reboot.
It booted fine and I reflashed the TWRP zip, in case I didn't do it properly. Again it did as expected.
I then pushed the latest prerooted 5.2.0.1 zip and rebooted to recovery, but again this generic screen, so I unplugged it early, I think.
From there on, I got stuck at the white amazon logo, see above.
I did not unlock the bootloader, adb shell confirmed it not being unlocked before.
During bootloops, I did not manage to get any control via adb or fastboot.
So, is it bricked once and for all? If not, how can I save it?
I don't care about anything stored on it.
I also have a Y-USB-OTG cable and connected a keyboard before, but could not interfere yet.
(If bricked, would a Teensy be of any use? I have one from CCast rooting days)
Thanks for reading and in advance.
Click to expand...
Click to collapse
I guess you did not read enough.
At this point in time you can only root (kingoroot or kingroot) and replace root with SuperSu on a Firestick. TWRP (recovery) can not be installed because it was not released by rbox as of yet, that particular recovery\pre-rooted image is for firetv1 upgraded to OS5 and not for firestick.
Sorry man.
Have you tried to connect to a computer via USB and run kingoroot or kingroot for windows (whatever you used)? It is a small chance that will recover but it is a slim one....
mjnman said:
I had same problem with my fire stick when used the USB power of my TV.
Did you try to power the fire stick TV with the power point and USB adapter?
Click to expand...
Click to collapse
I could not remember, so I just retried it with two different chargers and two different cables (both used to power my Nexus 5).
Unfortunately resulting in the very same loop... But thanks nonetheless.
bula1ca said:
I guess you did not read enough.
At this point in time you can only root (kingoroot or kingroot) and replace root with SuperSu on a Firestick. TWRP (recovery) can not be installed because it was not released by rbox as of yet, that particular recovery\pre-rooted image is for firetv1 upgraded to OS5 and not for firestick.
Sorry man.
Have you tried to connect to a computer via USB and run kingoroot or kingroot for windows (whatever you used)? It is a small chance that will recover but it is a slim one....
Click to expand...
Click to collapse
Dang... Usually I don't make mistakes this dumb. Guess I learned my first lesson. I'll try to trace my mistake though, for future attempts.
I rooted it with the Kingo app, I think, and got that typical "stuck at 90%" and rebooted it like others did. It rebooted fine and Kingo verified it rooted.
I did not use Windows, I use Ubuntu, occasionally with Wine, yet I had no luck passing USB devices to it. (And always these missing libs...)
Normally, adb and fastboot (console) work fine (i.e. with my phone).
Now I have no chance to interfere with the bootloop, I think.
IIRC, sometimes I could spam commands and at one point adb was stuck at "waiting for device".
I tried to reproduce it just now, but could not get it again.
So, should I try adb or fastboot on another computer to be sure?
Would King(o) for Windows be of any help at this point? If so, what would be my best bet to catch it at some point I can recover it?
Is there any other way I could try? From my nooby perspective, could the bootsplash be an entrance for fastboot? Could it be just stuck trying to access erroneous partitions?
At this point I would try the most crazy and risky idea, since it is unusable anyway.
Thanks both of you for your answers.
l_aios said:
I could not remember, so I just retried it with two different chargers and two different cables (both used to power my Nexus 5).
Unfortunately resulting in the very same loop... But thanks nonetheless.
Dang... Usually I don't make mistakes this dumb. Guess I learned my first lesson. I'll try to trace my mistake though, for future attempts.
I rooted it with the Kingo app, I think, and got that typical "stuck at 90%" and rebooted it like others did. It rebooted fine and Kingo verified it rooted.
I did not use Windows, I use Ubuntu, occasionally with Wine, yet I had no luck passing USB devices to it. (And always these missing libs...)
Normally, adb and fastboot (console) work fine (i.e. with my phone).
Now I have no chance to interfere with the bootloop, I think.
IIRC, sometimes I could spam commands and at one point adb was stuck at "waiting for device".
I tried to reproduce it just now, but could not get it again.
So, should I try adb or fastboot on another computer to be sure?
Would King(o) for Windows be of any help at this point? If so, what would be my best bet to catch it at some point I can recover it?
Is there any other way I could try? From my nooby perspective, could the bootsplash be an entrance for fastboot? Could it be just stuck trying to access erroneous partitions?
At this point I would try the most crazy and risky idea, since it is unusable anyway.
Thanks both of you for your answers.
Click to expand...
Click to collapse
Do you still have root? Is your stick responding to the su command?
If so read this post: http://forum.xda-developers.com/fire-tv/help/guidance-recovering-bootloop-firetv-t3446902
If not:
Try kingoroot for windows however it is a slim change in my opinion as you wrote a FireTv image to your FireStick.
Copy and paste from: http://forum.xda-developers.com/fire-tv/development/guide-fire-stick-replace-king-o-root-t3440923
"IF YOU RUN INTO SOFTBRICK ISSUE (stuck at fire tv logo)
Make sure you have ADB drivers properly installed in your windows pc/laptop.
connect a genuine usb lead to the firestick/pc.
download the windows version of KINGO ROOT and install it.
open KINGO ROOT on the pc with Fire Stick connected up to pc and tv.
wait for the button to pop up and click root.
if you dont see AFTV or get enable debugging in the KINGO ROOT program on pc/laptop please unplug the stick from usb and replug it back in.
if this still wont work restart the pc/laptop or try another pc/laptop.
you should after clicking root boot back up into your homescreen, if it doesnt boot back into your homescreen automatically, wait around 5 minutes and unplug usb and re-plug it again. "
bula1ca said:
Do you still have root? Is your stick responding to the su command?
If so read this post: http://forum.xda-developers.com/fire-tv/help/guidance-recovering-bootloop-firetv-t3446902
If not:
Try kingoroot for windows however it is a slim change in my opinion as you wrote a FireTv image to your FireStick.
Copy and paste from: http://forum.xda-developers.com/fire-tv/development/guide-fire-stick-replace-king-o-root-t3440923
"[...]"
Click to expand...
Click to collapse
Thanks for the links, but from what I see, I need to get past the bootloader splash for adb to work. I'm stuck at the white "amazon" splash, not the colored "FireTV Stick" splash after the amazon one.
Sorry for not making it clear (and for that amount of text that maybe hid it)...
From what I understand and recall, I did only flash the recovery, right? Or does it automatically flash the zip I pushed to internal storage?
And what confuses me, the first attempt booting into recovery AFTER flashing the wrong one I got the former mentioned screen with red text. Reboot worked and the Stick was running. So I did retry and got the same red text after rebooting to recovery. I assumed it did not flash again and unplugged it earlier than the first attempt. Since then it got stuck at the white bootsplash.
Since I am still a noob, it seems to me the system wasn't touched, maybe a faulty recovery integrity forcing the bootloader to loop.
l_aios said:
Thanks for the links, but from what I see, I need to get past the bootloader splash for adb to work. I'm stuck at the white "amazon" splash, not the colored "FireTV Stick" splash after the amazon one.
Sorry for not making it clear (and for that amount of text that maybe hid it)...
From what I understand and recall, I did only flash the recovery, right? Or does it automatically flash the zip I pushed to internal storage?
And what confuses me, the first attempt booting into recovery AFTER flashing the wrong one I got the former mentioned screen with red text. Reboot worked and the Stick was running. So I did retry and got the same red text after rebooting to recovery. I assumed it did not flash again and unplugged it earlier than the first attempt. Since then it got stuck at the white bootsplash.
Since I am still a noob, it seems to me the system wasn't touched, maybe a faulty recovery integrity forcing the bootloader to loop.
Click to expand...
Click to collapse
I have no idea what you did however it will not automatically flash your zip, problem is you installed TRWP that was not meant for Firestick and overwrote its booting sequence. You most probably would had recover from your first attempt by re-installing a new image but once you tried to install it again it most probably finished writing the whole thing and damaged booting sequence.
bula1ca said:
I have no idea what you did however it will not automatically flash your zip, problem is you installed TRWP that was not meant for Firestick and overwrote its booting sequence. You most probably would had recover from your first attempt by re-installing a new image but once you tried to install it again it most probably finished writing the whole thing and damaged booting sequence.
Click to expand...
Click to collapse
Yeah, sad thing I got the wrong device, should have taken my time even more...
I googled the screen I got to two times before getting stuck:
http://forum.xda-developers.com/showpost.php?p=65968901&postcount=60
First time I waited approx. 15 minutes before pulling the plug to reboot. Since I noticed no difference I tried again and got the same screen. But this time I pulled the plug earlier, <1 minute.
I'd like to add that my bootloader was locked. Can I damage the booting sequence by corrupting the recovery or was my mistake that major to be able to do that?
I googled some key combinations to get into recovery or to bypass it, but I don't know if I get the right keys.
With my remote control I don't think I have enough time to hold the keys. Additionally I have a USB keyboard (Cherry KC1000; if possible, which keys btw?) and may be able to connect it via powered Y OTG cable.
So if anyone got any further input or ideas for me to rescue my FTVS, I'd be glad to receive it.
Thanks to all.
Anyone else maybe an idea?
The thing is, I cannot believe it is unsavable.
To summarize the current state (please see full details above):
- stuck in bootloop, white amazon logo
- flashed wrong recovery, after first flash the system booted, after second flash it got stuck (characteristics above)
- never flashed anything other than recovery
Strange thing it booted in first place, but now it refuses. Also I got the screen I mentioned above and unplugged as described above.
Can I possibly bypass the recovery check and try to boot directly to system? Or maybe interrupt for fastboot access?
If connected to PC, can you see it thru 'lsusb'? Or 'dmesg | tail'?
Kramar111 said:
If connected to PC, can you see it thru 'lsusb'? Or 'dmesg | tail'?
Click to expand...
Click to collapse
I tried both
watch -n 0.5 'dmesg | tail'
and
watch -n 0.5 'lsusb'
but with no identification whatsoever.
I double-checked with my Nexus 5 on the same port with the same cable, it identified fine.
One last bump for ideas before putting it into the trash.

Fire TV 2nd Gen stuck in some kind of kiosk mode?

I purchased a used Fire TV 2nd gen online but when I boot it up, it goes into some kind of kiosk slideshow for 1st gen Amazon Echo devices that I can't exit.
It boots normally at first with the Fire TV logo an all but there's no config screen or anything. It boots to a white AMAZON ECHO screen with pics of the original Echo device then goes into a slide show showing all the various features of Amazon echo. The remote doesn't sync and the device will only show up on the Fire TV remote app for a few seconds before disappearing after boot. I can plug in a physical keyboard and if I press the ESC key, the screen will go black for a second before re-starting the slide show from the beginning. So far I've not been able to find any other keyboard functions that react, only the ESC key so far.
If I had to guess, I'd say it probably has a much older version of the OS on it as the slide show is for the older generations of Echo.
I'm assuming this used to be some kind of demo device, maybe from Best Buy or something but does anyone know how to get out of this slide show so it can be used as a normal device or is this thing just useless? Suggestions?
Hannover2k said:
I purchased a used Fire TV 2nd gen form ebay but when I boot it up, it goes into some kind of kiosk slideshow for Amazon Echo that I can't exit.
It boots normally at first with the Fire TV logo an all but there's no config screen or anything. It boots to a white AMAZON ECHO screen with pics of the original Echo device then goes into a slide show showing all the various features of Amazon echo. The remote doesn't sync and the device will only show up on the Fire TV remote app for a few seconds before disappearing after boot. I can plug in a physical keyboard and if I press the ESC key, the screen will go black for a second before re-starting the slide show from the beginning. So far I've not been able to find any other keyboard functions that react, only the ESC key so far.
If I had to guess, I'd say it probably has a much older version of the OS on it as the slide show is for the older generations of Echo.
I'm assuming this used to be some kind of demo device, maybe from Best Buy or something but does anyone know how to get out of this slide show so it can be used as a normal device or is this thing just useless? Suggestions?
Click to expand...
Click to collapse
Just as an update, I found that if I plug in a USB keyboard, pressing ALT+ESC will pop up a menu telling me to press the home button if I wish to return to the home screen. No remote works with it yet so that doesn't help much. Pressing ALT+Space will bring up what appears to be the FireTV search keyboard but typing doesn't bring up anything, it just echos what I type and there's no 'ENTER' key to submit anything.
If I do this immediately after the slideshow comes up, it will prompt that there's no network connection and take me to the network settings menu. I tried plugging in a LAN cable but the device doesn't seem to pull up an IP address. I manually entered an IP but was unable to find it on the network. Even tried using the APPS2FIRE app to see if it could see it in the search but it doesn't. I connected it to wifi successfully but same issue, it doesn't seem to actually pull an IP address as I can't see it on my network when I scan for it. The network settings know when the LAN is plugged in and removed though.
Plugging in USB A-A doesn't seem to do anything. I tried running the Unbrick batch file from one of the other posts but it's intended to work on non-rooted devices with the jumper trick, I think, and while it does kick off the script, it stops at 0% and never does anything. I'm sure this is an older OS that can still be rooted but I just don't know how to get to anything in it since I can't get into ADB.
Any suggestions would be appreciated though!
Hannover2k said:
I'm sure this is an older OS that can still be rooted but I just don't know how to get to anything in it since I can't get into ADB.
Any suggestions would be appreciated though!
Click to expand...
Click to collapse
If you can't get device to show up on adb devices via terminal/command prompt or access settings menu I don't think there's much you can do.
1.Try doing a scan with Fing Network Tools and see if IP shows.
2. Try downloading and installing FireTV remote App on your phone and connecting if it finds stick.
Without adb being activated on the stick, and settings menu unavailable to enable adb there is not much else for it m8, these ebay sticks are dodgy to say the least I've been stung a few times. Even bought one and opened it to find the heat shield casing missing and clk broke lol
Bertonumber1 said:
If you can't get device to show up on adb devices via terminal/command prompt or access settings menu I don't think there's much you can do.
1.Try doing a scan with Fing Network Tools and see if IP shows.
2. Try downloading and installing FireTV remote App on your phone and connecting if it finds stick.
Without adb being activated on the stick, and settings menu unavailable to enable adb there is not much else for it m8, these ebay sticks are dodgy to say the least I've been stung a few times. Even bought one and opened it to find the heat shield casing missing and clk broke lol
Click to expand...
Click to collapse
I'll give those a shot. I tried the jumper technique from the Unbrick Fire TV 2 post and was able to get partway through that process and to the prompt where it tells me to remove the jumper and press enter but it gets an error after copying the files, just before it should boot to twrp. something about the source path being empty. I can post a pic if that's helpful. I think may have forgotten to run the disable modemmanager command so I'll give that another try later. I didn't realize you had to run that every time you reboot linux. I know just enough to be dangerous with it.
Hannover2k said:
I'll give those a shot. I tried the jumper technique from the Unbrick Fire TV 2 post and was able to get partway through that process and to the prompt where it tells me to remove the jumper and press enter but it gets an error after copying the files, just before it should boot to twrp. something about the source path being empty. I can post a pic if that's helpful. I think may have forgotten to run the disable modemmanager command so I'll give that another try later. I didn't realize you had to run that every time you reboot linux. I know just enough to be dangerous with it.
Click to expand...
Click to collapse
Yeah great have a look here too
https://docs.google.com/document/u/0/d/1zYtqmf4RfLOkrPyPjf1C0CjAZf_0E1JohIlTyVY5kGs/mobilebasic
Files here
https://drive.google.com/drive/u/0/mobile/folders/1GbMTBHuFhwT_uyZaJs0ApsG_RQ5Wg_7F
Should work :good:
Bertonumber1 said:
Yeah great have a look here too
https://docs.google.com/document/u/0/d/1zYtqmf4RfLOkrPyPjf1C0CjAZf_0E1JohIlTyVY5kGs/mobilebasic
Files here
https://drive.google.com/drive/u/0/mobile/folders/1GbMTBHuFhwT_uyZaJs0ApsG_RQ5Wg_7F
Should work :good:
Click to expand...
Click to collapse
Unfortunately I can't use those methods. While I can get into the network settings, I can't get into any other settings. I never I never left it connected to wifi so I've been using a LAN cable to test. Booting without the LAN causes it to get an error and takes me to the network settings but I can't get to anything else from there.
Been messing with the jumper method from https://forum.xda-developers.com/fire-tv/development/unbrick-fire-tv-stick-2-anti-rollback-t3986303 but not having any luck yet as per the attached pic. Also tried the unbrick method which gets stuck at 000000200: 0% every time. Just for the heck of it, I shorted DAT0 and ran it and it popped up an error saying it can't locate a 'system' partition. The unit still boots up with the fire tv logo and goes into that demo mode so I'm sure there's a partition present. This is really a challenge! Running out of things to try though.
Hannover2k said:
Unfortunately I can't use those methods. While I can get into the network settings, I can't get into any other settings. I never I never left it connected to wifi so I've been using a LAN cable to test. Booting without the LAN causes it to get an error and takes me to the network settings but I can't get to anything else from there.
Been messing with the jumper method from https://forum.xda-developers.com/fire-tv/development/unbrick-fire-tv-stick-2-anti-rollback-t3986303 but not having any luck yet as per the attached pic. Also tried the unbrick method which gets stuck at 000000200: 0% every time. Just for the heck of it, I shorted DAT0 and ran it and it popped up an error saying it can't locate a 'system' partition. The unit still boots up with the fire tv logo and goes into that demo mode so I'm sure there's a partition present. This is really a challenge! Running out of things to try though.
Click to expand...
Click to collapse
You may have a stick that cannot be rooted/modified via amonet, one with dl mode disabled. These devices around December 2019 started to appear on the market and there's no way round them.
Bertonumber1 said:
You may have a stick that cannot be rooted/modified via amonet, one with dl mode disabled. These devices around December 2019 started to appear on the market and there's no way round them.
Click to expand...
Click to collapse
The device is a Fire TV 2nd gen Sloane so I would expect it to work like others I've rooted, but that kiosk os might do just what you said and disabled DL mode. I'll still play with it a bit but not sure what else can be done. Maybe some new method will come along in the future so I'll just hold on to it.
Thanks for all the input though. Greatly appreciated.
Hannover2k said:
The device is a Fire TV 2nd gen Sloane so I would expect it to work like others I've rooted, but that kiosk os might do just what you said and disabled DL mode. I'll still play with it a bit but not sure what else can be done. Maybe some new method will come along in the future so I'll just hold on to it.
Thanks for all the input though. Greatly appreciated.
Click to expand...
Click to collapse
Sorry mate my bad I thought it was a stick you had I was helping some other guy in firestick tank forum and got mixed up.
Try the short method again only when you get the error :
Leave dc power on (plugged into box)
Remove USB a to USB a cable
Close terminal
Open new terminal up in amonet once again
Run the boot-rom step again BUT hit enter TWICE
Then plug USB cable back in
Pull the dc power and plug it in again
The script should go through
I followed this from another member and it always works for me, has worked on numerous Sloanes. Give it a go, worth a shot mate
Bertonumber1 said:
Sorry mate my bad I thought it was a stick you had I was helping some other guy in firestick tank forum and got mixed up.
Try the short method again only when you get the error :
Leave dc power on (plugged into box)
Remove USB a to USB a cable
Close terminal
Open new terminal up in amonet once again
Run the boot-rom step again BUT hit enter TWICE
Then plug USB cable back in
Pull the dc power and plug it in again
The script should go through
I followed this from another member and it always works for me, has worked on numerous Sloanes. Give it a go, worth a shot mate
Click to expand...
Click to collapse
Thanks for the info, it's worth a try. Just to clarify, when you say to press enter twice, do you mean to press it twice at the prompt where it tells you to remove the short and press enter?
Hannover2k said:
Thanks for the info, it's worth a try. Just to clarify, when you say to press enter twice, do you mean to press it twice at the prompt where it tells you to remove the short and press enter?
Click to expand...
Click to collapse
Hey @Hannover2k, yeah the Sloane is stubborn to root, just keep at it, once you see ***remove short and hit enter** and get an error try leaving it switched on but remove USB, then run the script again and hit enter again after you hit it once, disconnect/reconnect the dc power and plug USB in without the short (if displaying remove short) . Should go through
Another thing...
This what happened to me the other day. If your preloader is gone (it's displaying remove short when there is no short). Disconnect power, disconnect USB, run the the script and connect power and wait 50-70 seconds then plug USB back in.
As I said these Sloanes are tough but you should get it, using the short "jumper" method m8
Bertonumber1 said:
Hey @Hannover2k, yeah the Sloane is stubborn to root, just keep at it, once you see ***remove short and hit enter** and get an error try leaving it switched on but remove USB, then run the script again and hit enter again after you hit it once, diconnect/reconnect the dc power. Should go through
Another thing...
This what happened to me the other day. If your preloader is gone (it's displaying remove short when there is no short). Disconnect power, disconnect USB, run the the script and connect power and wait 50-70 seconds then plug USB back in.
As I said these Sloanes are tough but you should get it, using the short "jumper" method m8
Click to expand...
Click to collapse
Sorry is I'm missing something here. I've been trying to do your method and while I've been getting different error messages and results, I'm still not quite sure I'm doing it right.
After I get the first error after removing the short, you mention above to remove the USB then run the script again, etc. At what point do I plug the USB cable back in? Do I plug the USB back in after removing the power? When I do remove the power, do i need to reconnect the Jumper before plugging it back in?
Sorry if I'm lame, I've just done this jumper thing 100 times and can get many different results but not the one we're looking for! lol
UPDATE: Holy cow, I got it to work the very next time after posting the message! Here's what I did:
1) Ran the script, connected jumper and powered on the device.
2) Got error message.
3) Unplugged USB then re-ran script, pressing enter again after running the command.
4) Plugged USB back in.
I did not reconnect the jumper. When the USB cable was re-connected it did display a message to remove the jumper and press enter, however I did not have to do that. All kinds of stuff started flying all over the screen, then it got to;
Clearing Preloader Header
Flashing Tee
Flashing Bootloader
Flashing Unbrick Image
Flashing Boot
Booting to TWRP
I'm literally grinning ear to ear right now! Thanks for all your help with this! Even if it doesn't work at this point, I'm very happy to have gotten this far!
I can get these kiosk devices for $20 each. Box only, no power or remote. Does anyone think it would be worth it to buy a few of them and try to sell them off with refreshed imaged on them? There's a lot available so just wondering.
Hannover2k said:
Sorry is I'm missing something here. I've been trying to do your method and while I've been getting different error messages and results, I'm still not quite sure I'm doing it right.
After I get the first error after removing the short, you mention above to remove the USB then run the script again, etc. At what point do I plug the USB cable back in? Do I plug the USB back in after removing the power? When I do remove the power, do i need to reconnect the Jumper before plugging it back in?
Sorry if I'm lame, I've just done this jumper thing 100 times and can get many different results but not the one we're looking for! lol
UPDATE: Holy cow, I got it to work the very next time after posting the message! Here's what I did:
1) Ran the script, connected jumper and powered on the device.
2) Got error message.
3) Unplugged USB then re-ran script, pressing enter again after running the command.
4) Plugged USB back in.
I did not reconnect the jumper. When the USB cable was re-connected it did display a message to remove the jumper and press enter, however I did not have to do that. All kinds of stuff started flying all over the screen, then it got to;
Clearing Preloader Header
Flashing Tee
Flashing Bootloader
Flashing Unbrick Image
Flashing Boot
Booting to TWRP
I'm literally grinning ear to ear right now! Thanks for all your help with this! Even if it doesn't work at this point, I'm very happy to have gotten this far!
I can get these kiosk devices for $20 each. Box only, no power or remote. Does anyone think it would be worth it to buy a few of them and try to sell them off with refreshed imaged on them? There's a lot available so just wondering.
Click to expand...
Click to collapse
@Hannover2k Yeah that's you got it sorted then, I tried to explain that method but didn't do a very good job of it lol, make sure you push pre-rooted rom and supersu 2.82 zip to /sdcard, and flash.
Please Remember and note that you cannot flash unsigned zips such as magisk to the Sloane as you're bootloader remains incarcerated , if you're device has cleared preloader and you've entered into twrp it should work
Ps. if you can get a Sloane for that price pm me and we'll sort something, doesn't matter about power cables, remotes etc
Bertonumber1 said:
@Hannover2k Yeah that's you got it sorted then, I tried to explain that method but didn't do a very good job of it lol, make sure you push pre-rooted rom and supersu 2.82 zip to /sdcard, and flash.
Please Remember and note that you cannot flash unsigned zips such as magisk to the Sloane as you're bootloader remains incarcerated , if you're device has cleared preloader and you've entered into twrp it should work
Ps. if you can get a Sloane for that price pm me and we'll sort something, doesn't matter about power cables, remotes etc
Click to expand...
Click to collapse
After flashing the pre-rooted image the first time, everything seemed to work except whenever I restarted via the settings menu, it would show the TWRP pre boot screen but allowing it to continue to boot normally would result in a boot loop. Performing a power cycle would cause the device to skip over the TWRP menu and boot right into the device.
Tried clearing the SD partition and dalvik to free up space as it was only showing about 1.2gb free after the flash. Got the free space back but still the same boot issue after flash, though it did work after a power cycle as opposed to restarting, which I rarely do anyways.
Remembering the Kiosk was for the original echo devices, I got to thinking about it having an older OS again and maybe not liking being flashed directly to the latest version so I re-flashed it to v5.2.6.7_r1. It would boot loop after the TWRP pre login screen but after the first loop it would boot properly. Went ahead and flashed it back to 5.2.7.3_r1 and everything seems to be working perfectly now. Restarts properly and all functionality seems to be present.
I really appreciate your assistance with this. I had them send me another one so I can try this method once more and if it works again, I'll definitely let you know and we'll work something out.
-Han
Hannover2k said:
After flashing the pre-rooted image the first time, everything seemed to work except whenever I restarted via the settings menu, it would show the TWRP pre boot screen but allowing it to continue to boot normally would result in a boot loop. Performing a power cycle would cause the device to skip over the TWRP menu and boot right into the device.
Tried clearing the SD partition and dalvik to free up space as it was only showing about 1.2gb free after the flash. Got the free space back but still the same boot issue after flash, though it did work after a power cycle as opposed to restarting, which I rarely do anyways.
Remembering the Kiosk was for the original echo devices, I got to thinking about it having an older OS again and maybe not liking being flashed directly to the latest version so I re-flashed it to v5.2.6.7_r1. It would boot loop after the TWRP pre login screen but after the first loop it would boot properly. Went ahead and flashed it back to 5.2.7.3_r1 and everything seems to be working perfectly now. Restarts properly and all functionality seems to be present.
I really appreciate your assistance with this. I had them send me another one so I can try this method once more and if it works again, I'll definitely let you know and we'll work something out.
-Han
Click to expand...
Click to collapse
The recovery partition maybe corrupted.
You may try updating twrp to the latest 3.0.05 from Sloane Twrp recovery page.
There you can download the file from here :
https://www.mediafire.com/file/brae6r8lu1np5jm/firetv2_recovery_v6.zip/file
,push it to Sloane /sdcard and run command
from pc
adb shell
Then run:
sh /sdcard/firetv2_recovery_v6.zip
Reboot
That should fix it.
As soon as you update TWRP
Reboot and flash the pre-rooted firmware and supersu 2.82.zip
Then wipe cache, dalvik
Let it boot up and then factory reset (data, dalvik, cache)
Reboot and it should be okay
Bertonumber1 said:
The recovery partition maybe corrupted.
You may try updating twrp to the latest 3.0.05 from Sloane Twrp recovery page.
There you can download the file from here :
https://www.mediafire.com/file/brae6r8lu1np5jm/firetv2_recovery_v6.zip/file
,push it to Sloane /sdcard and run command
from pc
adb shell
Then run:
sh /sdcard/firetv2_recovery_v6.zip
Reboot
That should fix it.
As soon as you update TWRP
Reboot and flash the pre-rooted firmware and supersu 2.82.zip
Then wipe cache, dalvik
Let it boot up and then factory reset (data, dalvik, cache)
Reboot and it should be okay
Click to expand...
Click to collapse
Thanks for the info. The image I installed already had that version of TWRP installed on it but like I said in my last comment, flashing to an older rom then re-flashing back to the latest one seems to have resolved the issue.
No more Kiosk mode, though I wish I could have gotten a look at those files just to see what was going on there.
Anyways, all good now and I have another one of those kiosk units I'm going to try the process again on and if it works, I have access to a lot of these devices so I may refresh them and sell them cheap.
Thanks again for everyones input! Still surprised I got it working normal again.
Bertonumber1 said:
@Hannover2k Yeah that's you got it sorted then, I tried to explain that method but didn't do a very good job of it lol, make sure you push pre-rooted rom and supersu 2.82 zip to /sdcard, and flash.
Please Remember and note that you cannot flash unsigned zips such as magisk to the Sloane as you're bootloader remains incarcerated , if you're device has cleared preloader and you've entered into twrp it should work
Ps. if you can get a Sloane for that price pm me and we'll sort something, doesn't matter about power cables, remotes etc
Click to expand...
Click to collapse
Good news!
I was given a 2nd unit with the same 'issue' and was able to get it to start taking the image within a couple mins. The guy who has them can't do anything with them and has lowered his price per unit so are these worth anything to anyone?
Again, it's the box only, no power cords or remote but I don't expect that to be an issue for someone looking to replace one.
I hope I'm not breaking any rules by asking that but I'm open to any thoughts on this.
-Han
Hannover2k said:
Good news!
I was given a 2nd unit with the same 'issue' and was able to get it to start taking the image within a couple mins. The guy who has them can't do anything with them and has lowered his price per unit so are these worth anything to anyone?
Again, it's the box only, no power cords or remote but I don't expect that to be an issue for someone looking to replace one.
I hope I'm not breaking any rules by asking that but I'm open to any thoughts on this.
-Han
Click to expand...
Click to collapse
@Bertonumber1
Sus_i said:
@Bertonumber1
Click to expand...
Click to collapse
Yeah I've already replied via pm to @Hannover2k I've already bought one with power brick and remote for Roger @Sus_i hannover2k only has the Sloane itself AFAIK I got the full shebang for £27 so it's all good perhaps @Hannover2k can provide a spare and that's us got a couple to got to work on in the name of furthering development
Bertonumber1 said:
Yeah I've already replied via pm to @Hannover2k I've already bought one with power brick and remote for Roger @Sus_i hannover2k only has the Sloane itself AFAIK I got the full shebang for £27 so it's all good perhaps @Hannover2k can provide a spare and that's us got a couple to got to work on in the name of furthering development
Click to expand...
Click to collapse
Hannover2k said:
Sorry is I'm missing something here. I've been trying to do your method and while I've been getting different error messages and results, I'm still not quite sure I'm doing it right.
After I get the first error after removing the short, you mention above to remove the USB then run the script again, etc. At what point do I plug the USB cable back in? Do I plug the USB back in after removing the power? When I do remove the power, do i need to reconnect the Jumper before plugging it back in?
Sorry if I'm lame, I've just done this jumper thing 100 times and can get many different results but not the one we're looking for! lol
UPDATE: Holy cow, I got it to work the very next time after posting the message! Here's what I did:
1) Ran the script, connected jumper and powered on the device.
2) Got error message.
3) Unplugged USB then re-ran script, pressing enter again after running the command.
4) Plugged USB back in.
I did not reconnect the jumper. When the USB cable was re-connected it did display a message to remove the jumper and press enter, however I did not have to do that. All kinds of stuff started flying all over the screen, then it got to;
Clearing Preloader Header
Flashing Tee
Flashing Bootloader
Flashing Unbrick Image
Flashing Boot
Booting to TWRP
I'm literally grinning ear to ear right now! Thanks for all your help with this! Even if it doesn't work at this point, I'm very happy to have gotten this far!
I can get these kiosk devices for $20 each. Box only, no power or remote. Does anyone think it would be worth it to buy a few of them and try to sell them off with refreshed imaged on them? There's a lot available so just wondering.
Click to expand...
Click to collapse
Just wanted to add my Order of Operations to this post. I also bought one of these "Kiosk" boxes without remote or power supply for $13 off of eBay. Great deal, I thought, if I can get it to root. It appears that the order in which you perform the steps is unique to your setup. After trying all the above suggestions with no success (similar errors as listed above), here's what worked for me:
1. Plug in male-to-male USB cable between FTV2 and Linux box
2. Short DAT0 pin on FTV2 board
3. Connect FTV2 AC power
4. Run script
5. Remove short, press enter once when prompted
After TWRP installed (and I figured out how to use it), I was successful in having a usable FTV2 with all of the perks this process brings. Thanks to all who contributed to make this possible, and an extra big thanks to @Hannover2k for being the first to try this on these specifically-challenged boxes. It was a huge help!

Categories

Resources