** Unlock Bootldr first in Download Mode.
** Flash (downgrade) to lower Firmware with the same Binary.
** Everytime you use Odin again make sure you click reset and disable auto reboot.
Things you need:
=============
- TWRP (Root + Magisk) - TWRP_A505_QQ_BTC4
- magisk_patched.tar
- Magisk.APK (latest)
- SmaliPatcher-0.0.6.7-fOmey_XDA
** Plug in your cable.
** Do not forget to Enable Developer Options
1) Enable OEM + Debug and Flash Stockrom in Odin
** If Oem doesn't show up.. Op en General Management/ Date and Time/ Disable 'Use 24-hour format'
** Connect to WI-FI and reboot the Phone, it will show up.
2) Now turn 'Off' the phone.
3) Now hold Down Button and Power Button, the Download Menu will show up.
4) Now open Odin and flash TWRP_A505_QQ_BTC4.tar
5) Once done.. hold Down Button and Power Button for 7sec.
6) Now the Phone will reboot a few times, wait till your able to config it.
** Do not connect with WI-FI yet.
7) Once done.. enable 'Developer Options'
** Do not forget to Enable Developer Options again.
** Disable Auto Update System
** Enable USB Debugging
** Disable Auto Download over WI-FI in 'Software Information'
8) Put Magisk.APK on the Micro SD Card from the phone and install the APK.
Run the App and leave it open.
Now extract the Update Firmware from your phone model and copy the AP file to your desktop.
Connect the phone to Pc and place the AP file on the Micro SD Card.
Go back to the app 'Magisk' on the phone and select 'Magisk is not installed - Install'
Tab 'Install' and choose 'Select and Patch a File'
Now open the file AP and the app will start flashing.
Once the 'Image' is written.. press the disk image in the right top corner.
Now on Pc check the phone storage and open the folder 'Download'
Copy the files magisk_install_log_2020-08-11T02:25:08Z.log and magisk_patched.tar to Pc.
Once done
9) Now turn 'Off' the phone.
10) Hold Down Button and Power Button, the Download Menu will show up.
11) Now flash magisk_patched.tar in AP and BL, CP, Home_CSC from the Original Firmware.
12) Once done.. hold Down Button and Power Button.
13) Now the device will reboot a few times.. and you will be to configure it.
** Unplug your cord.
** Dont enable WI-FI yet in these options.
** If it doesn't start after 5min press Down Button and Power Button for 7sec.
** If it is rebooting when you configure it.. than just repeat to configure it once booted.
** Still rebooting? Make sure you press OK after the warning screen when its rebooting.
14) Once on the Phone screen.. Open Magisk APK and it will be installed.
** Check also with Root Checker to confirm.
15) Now connect to WI-FI and open Magisk app, (Dont let it download the ZIP file if it ask for)
** If it ask you to do.. clear cache and data in Settings/ Apps
16) Once done close the app again..
17) Now your device is rooted.
** Do not forget to Enable Developer Options again.
** Disable Auto Update System
** Enable USB Debugging
** Disable Auto Download over WI-FI in 'Software Information'
18) Run ADB and follow steps to install + Drivers.
Once done press OK.
19) SmaliPatcher
** Make sure 'Developer Options' and 'USB Debugging' is enabled.
Connect your phone from USB to Pc.
On the phone press 'OK' to enable 'USB Debugging'
Run SmaliPatcher and it will download the latest necessary binary's.
Now enable the options below.
- Mock Locations
- Secure Flag
- Signature Spoofing
- Samsung Knox
Now click on 'ADB PAtch' and wait till the task is done.
A file named '[email protected]' is now generated in the SmaliPatcher folder.
20) Install Module
Copy the output file '[email protected]' to Micro SD Card.
Now open 'Magisk' and in the options select 'Modules'
Tab on the + and search for the file you placed on the Micro SD Card.
Once done.. reboot the phone.
21) Install Fake GPS Location
Open up 'Play store' and search for Fake GPS Location - GPS Joystick (The App Ninjas)
Once installed.. go back to 'Developer Options'
Find the option 'Mock location app' and tab on it.
Choose 'GPS Joysctick' and close the menu.
22) Link2SD
Open up 'Play store' and search for Link2SD
Once installed.. open the app.
Grant acces and search for 'GPS Joystick'
Tab on it to open and tab again above in the right corner for options.
Now choose 'Convert to system app' and press 'OK'
Once done.. close the menu and reboot the phone.
** If this method didn't work.. go to App Store and download Root Browser.
** Copy the apk to root Directory/ System/ App/ (File Here)
** You could also load ADB Shell - SU - Mount - cp xxxx.apk /system/app or mv xxxx. apk /system/app
(Or search Google for isunshare 2 Ways to Convert User App to System App on Android)
23) Pokémon GO
Open up 'Play Store' and search for Pokémon GO.
Once installed.. close the menu.
24) Hide Magisk
Open the app and go to settings.
Enable the option 'Magisk Hide'
After this step search for 'Hide Magisk Manager'
Tab on it and rename it to 'Manager'
Once done.. Reboot your phone.
** To prevent losing Root acces..
I also provide you to check and disable every security option from apps and settings.
I used Method 1 & 2 for two times, after that it allowed me to update it to latest magisk v20.4
Also i disabled most security options on the phone and Magisk keeped root acces.
Method 1 !!
=========
1) Open settings.
2) Tab on About Phone.
3) Now scroll down and under 'Looking for something else' tab 'Reset'
4) Tab on Factory Data Reset and tab Reset/ Delete All.
5) Open Magisk and select 'Cancel' the download.
6) Now close the app and reboot your Phone.
7) Phone will reboot and keep Root acces.
Method 2 !!
=========
1) Open Settings.
2) Go to Apps.
3) Search for Magisk.
4) Tab on Storage.
5) Clear Caché and Data.
6) Now reboot your phone and it keep Root Acces without Rebooting every 10sec.
I am waiting for the day when someone will post a guide like this to fully enable camera2api and make Gcam work.
Related
Samsung Apps shows just 5 apps for my firmware (S5830SERKPE).
Here is how to get some more apps in the "Samsung Apps" - app
1.) install and start root-explorer
2.) click on Mount/RW
3.) navigate to /system/csc/sales_code.dat
4.) set permissions to Write outhers
5.) Just replace the text in the file to XEU (I had SER before)
6.) save
7.) set permissions back
8.) exit (phone will reboot, at least that happend to me)
Now I see 12 apps
I used this method to root my phone:
Copy the CWM_SuperUser_v3.0.7.zip file to the internal SD card of your phone.
Turn off your phone.
Boot your phone to ClockworkMod Recovery by pressing the Volume Up, Home, and Power keys together. Release them when the screen turns on.
Use the Volume buttons to navigate and the Power button to select an option.
Select Install ZIP From SD Card > Choose ZIP From SD Card and select the CWM_SuperUser_v3.0.7.zip file that you copied to your phone earlier.
Once you have flashed it, reboot your phone by selecting Go back and Reboot System Now.
Your phone is now rooted but you still need to install BusyBox on your phone. You can get it for free from the Google Play Store.
Run the BusyBox free application on your phone.
It will prompt you to allow root access. Select Allow.
Tap the red “X” in order to close the dialog window that will pop up.
Allow BusyBox to scan your phone.
Tap Install to install BusyBox and make the necessary file changes.
Update your su binaries by doing the following:
From the app drawer of your phone, open the Superuser app.
Tap the wrench icon on the upper corner to go to the app’s settings menu.
Under the General section towards the end of the list, tap “Su Binary”.
Select Update and you are done.
After I did this I was able to send text messages, but when I woke up the next morning I was no longer able to send texts. Does anyone know how I get my phone to send texts again? And yes I rebooted my phone, and unrooted it and rooted it again. Still the same problem occurs.Thanks
hi this phone was rooted on 25th sept(after many months of launch).i request the devs here someone to please develop an custom rom for the mobile or just mod the current one.
How to root?
By this time, many users may get rooted but there is no tutorial for that in androidforums so posting here.
Plus, I have modded original boot.img of A52 myself and added init.d support plus support for initializing ext2,3,4 modules on boot.
DOWNLOADS:
1) Unsecured boot.img (zip contains unsecured boot.img + A52 scatter file)
http://www.mediafire.com/?h9ubm9dhq9n7jjd
2) SP.FlashTool
http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
3) Drivers
http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
4) UnlockRoot
http://www.unlockroot.com/
Note: Usemastermind1024 as password to download above files.
Advantages of my boot.img:
I have added init.d support plus ext2.ko,ext3.ko & ext4.ko modules initialization on boot.Just place this ko files in /system/lib/modules/ after rooting the device, u will be able to use Link2SD with ext2,3 or 4 filesystems on your 2nd sdcard partition.
Press thanks if helped
Reference for flashing: MT65x3 flashing tutorial
Read the above tutorial first so u get idea how to flash an img file using SP FlashTool.
STEPS TO FLASH BOOT.IMG:
1) First install the drivers you downloaded & then run SPFlashTool, preferably as administrator (not mandatory)
2) Select USB mode under Options
3) Click Scatter-loading & select scatter file you downloaded from above links.
4) It will automatically load boot.img if it's in the same folder with scatter file otherwise click BOOTIMG & select the downloaded unsecured boot.img
5) Turn off the device fully, remove the battery for 5 seconds to be sure n re-insert the battery but do not power on device.
6) Attach the usb cable with PC but not with device
7) Now click on "Download" button on SPFlashTool, it will show searching for device in lower panel.
8) At this time, attach the cable with device in power off state
9) Now as soon as u attach the cable to device in power off state it will show a progress bar in lower panel n then a dialogue which states successfully flashed n another dialogue showing green colored ring n stating Download OK.
12) Close the dialogues, close the program n reboot the device by pressing power key.
STEPS TO ROOT DEVICE:
1. Power on device.
2. Enable USB Debugging.
- Settings > Application tab > Applications > Development > USB Debugging
3. Install UnlockRoot in pc
4. Attach device using usb cable in debugging mode(u just enabled it in step-2) to pc.
5. Now Run UnlockRoot program and click Root button
6. Confirm online device Micromax A52 in the list which pop-up.
7. Let in finish the procedure and Restart device when is asks.
8. See new Superuser app in app drawer
9. Viola...!!! Your A52 is now rooted.
UnlockRoot does not install Busybox on device so after u rooted the device install busybox to work with many root apps.Search Play Store for Busybox Installer by Jrummy OR BusyBox free by Stericson...
DISCLAIMER:
I am not responsible for bricked devices, dead SD cards, . Please do some research if you have any concerns before flashing! YOU are choosing to make these modifications, and if you point the finger at me for messing up your device
Press thanks if helped
Sorry beginners, this is for advanced users If you want, i can record video
!!!WARNING!!! In this phone is VIRUS! Please uninstall app eyuSales_blabla.apk!!!
A) Download my archive (186,4MB)
mega.co.nz/#!vdd1XRQb!Udy-BRprb8uw_c5HHVzusiEtoKkmOVLv36n_uxISeks
- Original ROM
- Custom ROM
- Drivers
- Flashing Tools
- Tools to edit ROM
B) Install any ROM
1. Power OFF you Phone
2. Start ChannelServer.exe from folder Server
3. Start ResearchDownload.exe from folder Flasher
4. Click to Load packet and then Start Downloading
5. Press volume down button and connect to PC. Instal Drivers, many drivers... (Win8 64bit sign problem - Settings, Computer Setting, General, Restart Now, disable sign check)
6. Finally flashing
7. Disconnect from PC, unplug Battery, plug Battery and Power ON!
C) Install part of ROM
1. Load original packet
2. Click to Settings butt
3. Select parts of ROM, ok and Start Downloading
4. Volume down, connect PC, flashing....
D) Edit ROM
1. Open ResearchDownload.exe, Load packet, Setting - find location system.img
2. Open Yaffey and open system.img
3. You can delete or add (import):
- bootanimation
- fonts
- sounds
- delete apps (for advaced users)
- add apps (import app to system/apps, then open app in WinRar, go to /lib/armeabi and copy this files to system/lib)
- manual ROOT - open root.zip and copy superuser.apk to system/app and copy "su" to system/bin. Right Click on "su", properties - check all checkboxes
4. Save as... and flash
E) Only ROOT
1. Flash recovery.img
2. Power, wait sec, volume down, wait sec, release power, wait sec, release volume down, wait...
3. You are in CWM Recovery - install root.zip from SD card
thank for post!
Not entirely working on device with 6820_2.35_C909_hteng_S2_RU_dt6206-V01
Hello,
I have this same phone, with 6820_2.35_C909_hteng_S2_RU_dt6206-V01.
Thanks to your post and also http://forum.xda-developers.com/showthread.php?t=2165554 I was able to get drivers working & flashing going.
However, this recovery.img and also all the ones from http://forum.xda-developers.com/showthread.php?t=2165554 result in a blank screen.
Does anyone have a working recovery for this version?
Problem
I have a problem!!!flashing is sucessful but when i on the phone,the screen inverted and i dont know what to do!!plss help!!
Samsung Galaxy S7 (SM-G930P) Root & Xposed Framework install Without Voiding Warranty
- So there are many posts about Rooting the Samsung galaxy s7 where some people will say it trips knox and others say it's to complicated.
- This easy guide includes resources from other XDA developers whom I was able to use to root my Sprint Samsung Galaxy S7 and install Xposed Framework without voiding my warranty.
-You can try what ever firmware you are on, however there are many reports of issues on the new firmware. when i first did it on the newest firmware i got a boot loop but easy to fix just by re-flashing the firmware with Odin.
- Unfortunately this method will erase all data if you are not currently in PE1 firmware
- You will not Brick your phone with this method, because it is very easy to just reflash the firmware with Odin.
Here is the link to download a RAR with all of the nessecary files!
-->https://mega.nz/#F!Egt23TLa!NrynMKoUvwngnsse2zo6hw<--
-I am not responsible for any damage done to your device through any steps taken tword rooting your Samsung Galaxy S7
-You will loose all your data if not currently on PE1 Firmware
- I am not to credit for all of these procedures, I only figured out how to Enable Tethering which im sure has been figured out by someone else as well.
The RAR file attached has ALL of the files you will need for the whole guide.
-So download and extract all of the files from the RAR
-Or you can follow each link to download the necessary files
1.Preparing:
1. Install Samsung drivers:
- Extract the RAR file "SAMSUNG_USB_Driver_for_Mobile_Phones.zip"
- Run "SAMSUNG_USB_Driver_for_Mobile_Phones.exe" as Administrator
- A USB Driver instillation wizard will pop up
- Click next
- Select the proper language and country or region
-Select next
- Set destination path, or use the default
- Then click install and let it work its magic
2. Install ADB:
- Execute (as Administrator) the file "adb-setup-1.3.exe" from the attached .rar
- It will ask you a series of questions, hit "Y" each time and hit enter
- Then it will bring you to a diver installation wizzard
- Click next
- Click finish
- You have successfully installed ADB
2.Flashing PE1 Firmware:
First off this method does require PE1 firmware. So here's how to get your Samsung Galaxy S7 to PE1 firmware:
-You can get the PE1 firmware in the attached RAR file
1. Connect your Samsung to your computer via OEM micro-usb cable.
2. Power down you samsung
3. Once powered down, hold Volume Down, Power, and the Home Button all at the same time
4. You will get a blue screen that says warning, read the text and the press Volume Up to select "Continue"
5. Launch Odin as Administrator
6. In Odin click the button "AP"
7. Select the "AP_G930PVPU2APE1_CL7925126_QB9448520_REV02_user_low_ship_MULTI_CERT.tar.md5" file
8. In Odin now click the button "CP"
9. Select the "CP_G930PVPU2APE1_CL7925126_QB9448520_REV02_user_low_ship_MULTI_CERT.tar.md5" file
10. In Odin now click the button "CSC"
11. Select the "CSC_SPT_G930PSPT2APE1_CL7925126_QB9448520_REV02_user_low_ship_MULTI_CERT.tar.md5" file
12. Then in Odin, press the botton that says "Start". Odin will begin flashing the PE1 firmware.
13. Once Finished, Odin should say "Pass", and your Samsung should then boot up to a first time setup procedure.
3.Before you Begin Rooting:
Once You have finished flashing PE1 firmware you should then download the following apps to your Samsung:
-Package Disabler Pro or EZ Package Disabler (both will do the job)
-Flash Fire
-Build Prop Editor
If you use Snapchat, now is the time to download, install, and login to the app
-Snapchat denies login to rooted andriod users, especially if Xposed Framework is installed.
4.Rooting:
Now that you have the pre-procedure done, go to the link directly below and start at "Here we go" for the rest of the rooting procedure instructions. Necessary files for colormedroid's precedure will also be in the attached RAR file.
http://forum.xda-developers.com/sprint-galaxy-s7/how-to/sm-g930p-root-t3410604
Once you have finished rooting you may follow the next steps.
5.Installing Xposed Framework, Xposed APK, as well as a tether mod
-Go to the link below and click on the tab that says "CLICK TO HIDE CONTENT" under the header "INSTALL XPOSED"
-Follow psouza4's steps to Installing Xposed
-However I have attached a better APK for xposed.
http://forum.xda-developers.com/ver...-to-notes-root-install-xposed-unroot-t3411039
6.Installing Xposed Module X tether for free native tethering
1. Go into the Xposed app
2. Tap on the 3 dashes in the upper left corner
3. Tap on the tab that says "Download"
4. Search for the module "X Tether"
5. Tap on the X Tether module
6. Tap the tab that says "Version"
7. Tap "Download" on the newest version
8. Then go back to the panel that has the option "Modules"
9. Tap the check box next to the "X Tether" module to activate it
10. Reboot
11. Bear with me here is gets a little more complicated
12. No that Xtether is installed and activated, we are going to edit a data base file to be able to use the native mobile hotspot
13. Download SQLite Editor app from the playstore (it does cost money, and there are probably others that can do it but this worked for me) https://play.google.com/store/apps/details?id=com.speedsoftware.sqleditor&hl=en
14. Open SQLite
15. Tap the tab that says "Files"
16. Navigate to /data/data/com.android.providers.telephony/databases
17. Then tap "telephony.db"
18. Then tap "carriers"
19. Look for the 2 lines that say "APN2 LTE internet" and "APN2 EHRPD internet"
20. Down those lines under "type" they both say "default,mms"
We will be changing it to say this
21. Tap on "default,mms" then tap the pencil in the upper right of SQLite. This will enable you to edit this setting.
22. Scroll down until you see the type "default,mms"
23. edit this to say ""default,mms,dun"
24. Tap save
25. Do this for both "APN2 LTE internet" and "APN2 EHRPD internet"
26. Exit SQLite and restart your phone
You can now enable the hotspot as if it were part of your service plan. If you go into to you settings>Hotspot and Tethering
Happy Tethering
How can I tell what firmware I am on? I don't see anything similar to PE3 in the Settings section of my S7. Thank you!
ghostofdavid said:
How can I tell what firmware I am on? I don't see anything similar to PE3 in the Settings section of my S7. Thank you!
Click to expand...
Click to collapse
This works on all builds other than 7.0 beta.
---------- Post added at 01:58 PM ---------- Previous post was at 01:56 PM ----------
Did you make sure to include the volte icon and cpu governor fixes? Don't use the debloat zip just use the fixes for those on any other build.