Hello community! I recently bought the Huawei Matepad Pro tablet, but, while the M-Pencil works fine, its original keyboard is not connecting with the device properly.
The follow the steps below:
1. I connect the keyboard to the tablet magnetically, to one of the two dedicated slots;
2. A message pops up prompting to connect, I hit "Connect";
3. A message confirms a successful connection, the CAPS key LED starts flashing slowly for 5-6 seconds;
4. The keyboard briefly disconnects and reconnects, with the CAPS key LED flashing rapidly for 2-3 seconds;
5. The keyboard disconnects entirely. Pressing reconnect gives an error that the device is either away from the keyboard or that the keyboard is connected to another device.
Any ideas as to what the problem is? I suspect it is a faulty product, but I would appreciate any feedback or troubleshooting tips!
Related
Hello,
Does anyone recognize this issue?
The keyboard should reconnect on pressing a key within a few seconds. However what happens:
-immediately the standard keyboard SIP icon is replaced by the igo icon, so it does make a connection.
-but the green led doesn't start blinking, and it doesn't start typing
-I have to repeatedly press a key, sometimes for 2~3 minutes
-then the led start blinking and i can start typing.
When I open the keyboard cnfg screen, in the BT tab, it says:
-waiting to reconnect, press any key etc. etc.
-repeatedly, it flashes to "connection is not setup" but immediately goes back to waiting to reconnect state,
-until ultimately the connection is enabled.
Setting up the connection with the standard built-in driver works perfectly, but i cannot use that anymore because i now also have a BT mouse.
I have an x51v with WM6
I use igo driver 4.52
So, please, does anyone recognize this problem? Is there a solution?
Thank you
Kuifje
Is anyone using a USB keyboard with their Tab 3? I have wierd problems with mine on a 4.2.2 t315. If there is a pause of more than about 2s between key presses the next key press causes the screen to turn off, the next one turns it back on (locked), the third one unlockes it and the fourth one gets correctly registered. I suspect there is either a problem with my keyboard (don't currently have another to check) or with the USB autosuspend that is set to 2s. Unfortunately I have not yet rooted my Tab (a bit scared to lose the warranty) otherwise I woul check if I can owrride the default USB autosuspend.
Any experience with this kind of problem?
After a couple of years of happy usage last night, my Firestick 2nd gen, got stuck on the home screen, and is now unresponsive to both the selector button, as well as the restart routine, (Holding down select and Play/Pause at the same time until it restarts).
I did a couple of hard restarts by unplugging it, and then plugging it back in, and it went through the entire startup routine, including the red "fire TV"" startup logo, and then it opened to the same frozen unresponsive uncooperative (Like my ex wife) screen.
I tried another remote, and that did not work either.
Just to see what would happen I blocked it on my network, since wifi blocking will take you to the "home is unavailable" firestick screen, which it did, but once I got there, the "Go to network settings" and "dismiss" options were unresponsive as well.
I don't mind having to reset it if I have to, but so far I haven't come up with a way to make it work.
All help appreciated.
Papamalo
papamalo said:
After a couple of years of happy usage last night, my Firestick 2nd gen, got stuck on the home screen, and is now unresponsive to both the selector button, as well as the restart routine, (Holding down select and Play/Pause at the same time until it restarts).
I did a couple of hard restarts by unplugging it, and then plugging it back in, and it went through the entire startup routine, including the red "fire TV"" startup logo, and then it opened to the same frozen unresponsive uncooperative (Like my ex wife) screen.
I tried another remote, and that did not work either.
Just to see what would happen I blocked it on my network, since wifi blocking will take you to the "home is unavailable" firestick screen, which it did, but once I got there, the "Go to network settings" and "dismiss" options were unresponsive as well.
I don't mind having to reset it if I have to, but so far I haven't come up with a way to make it work.
All help appreciated.
Papamalo
Click to expand...
Click to collapse
Have you tried a OTG with keyboard?
I have plugged the firestick into my desktop using a Micro USB to USB connector if that's what you mean, but even though it loads up and my "devices and printers" panel recognizes it as "MTP device" and the driver panel recognizes it as "ADB Device", no further info or control seems to be available.
So I guess it plugs in, but what should I do now?
Thanks.
An otg (on the go) cable and keyboard will give you control like a controller. You can try moving with the curser and enter. This would eliminate a Bluetooth issue when operating the remote.
papamalo said:
got stuck on the home screen, and is now unresponsive to both the selector button, as well as the restart routine
Click to expand...
Click to collapse
Have you tried fresh new batteries in the remotes?
Maybe you can install the app Remote for Fire TV from the amazon website (with the option send to fireTV Stick) and use your smartphone as remote.
normally this is the problem i get when the battery of the remote die..
This appened to my firetv stick 2nd edition just now. It happens after I plugged it in a new tv color.
Any ideas or a solution founded?
Thanks in advance!!
I have the OnePlus 5t and recently I bought the redmi airdots (Bluetooth 5.0 earphones) and I have some troubles to pair them. Every time i connect to them I get a notification asking me to pair and connect (pairing request), when I press yes, a pop up message appear asking to pair and connect again, then a press yes and it connects normally. the thing is, I had another Bluetooth headset from xiaomi too and when i simply turn on the headset it automatically connects without prompting to pair and connect like the airdots.
my question is, can I get rid of this notification and pop up message asking to pair? I would like to simply turn on my earphones and it automatically connect to my phone without the need to every time confirm to pair (since the earphones already are paired).
I already cleared the cache in the bluetooth app and reset the phone, but still nothing.
I had the same issue as you and this method solved the problem:
Procedure: STEP_1. Put your Airdrops in the box, make sure that its charged. Delete airdots from your bluetooth device in your phone.
STEP_2. Take out both of your Airdrops from box
STEP_3. Turn off both of Airdrops by pressing and keeping the button on it for 5 seconds (until you see red light)
STEP_4. Perform 2 kinds of reset (reset of stored Bluetooth device and reset of connection between both Airdrops headphones) To make this reset, press and hold the button on both airdrops for 20seconds (headphone have to blink after 10seconds and 20seconds) don't release the buttons until you don't see second blinking.
STEP_5. Turn on your Airdrops by pressing and holding the button on both of it for 5seconds or put it in box and take it out. (when you take it out from box they will automatically turn on).
After done restart, on right headphone, you have to see blinking white light but on the left one, you have to see no light. It's mean that there is connection between headphones, and right headphone is waiting for connection with the phone.
mazzidev said:
I had the same issue as you and this method solved the problem:
Procedure: STEP_1. Put your Airdrops in the box, make sure that its charged. Delete airdots from your bluetooth device in your phone.
STEP_2. Take out both of your Airdrops from box
STEP_3. Turn off both of Airdrops by pressing and keeping the button on it for 5 seconds (until you see red light)
STEP_4. Perform 2 kinds of reset (reset of stored Bluetooth device and reset of connection between both Airdrops headphones) To make this reset, press and hold the button on both airdrops for 20seconds (headphone have to blink after 10seconds and 20seconds) don't release the buttons until you don't see second blinking.
STEP_5. Turn on your Airdrops by pressing and holding the button on both of it for 5seconds or put it in box and take it out. (when you take it out from box they will automatically turn on).
After done restart, on right headphone, you have to see blinking white light but on the left one, you have to see no light. It's mean that there is connection between headphones, and right headphone is waiting for connection with the phone.
Click to expand...
Click to collapse
This fixed the problem. Thank you!
Hello, I have a Black Shark 3, I'm experiencing an annoying problem, the phone does not turn on, it turns on only if I force it with the Power button, when it turns on... it works normally. And another problem that is happening is that the "USB Debugging" function is not working, it is activated but the "MTP" notification does not appear, to make matters worse now it has a bootloop, but the usb is still not working. (The usb is working properly).