Develop Bugs

The image file is corrupt

Every time I try to run USL or update the ROM I get this error message after about 3-5%: The image file is corrupt. Can you help?

bring your device into bootloader mode , connect via as and try again!

ghiatti1 said:
Every time I try to run USL or update the ROM I get this error message after about 3-5%: The image file is corrupt. Can you help?
Click to expand...
Click to collapse
I sometimes get this if my firewall and antivirus is enabled

Antivirus and Firewall are disabled.
I tried to enter the bootloader mode by pressing the record key and reset, but the PDA just resets.

this is how you enter bootloader:
http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets

Just wanted to let you know that I have managed to update the ROM. I cannot tell why but it worked the 10th time! Sorry I cannot give any siggestions to anyone with the same problem.

I got this error when trying to install newest Codon Rom on my device without cid-unlocking the device before. After I cid-unlocked the rom I did not get the "image corrupt" warning.
I did not try to reproduce it after I installing the rom, maybe you could give this a try.
regards,
Daniel

Stucked in bootloader loop, locked, download and recovery mode works, Original ROM

Hello all,
I'm having this issue for a week and I tried every possible solution on xda before opening this thread.
My situtation is;
-I tried to restart my phone last week and it is stuck in bootloader mode since (locked, s-on)
-Firmware version is 3.35.401.32
- since I can't restart my phone, I can't even enable usb debugging
-when I try to use reinstall the 3.35.401.32 version in adb mode, I get "e:footer is wrong e:signature verification failed"
-download mode and recovery mode works just fine
Can you guys help me out please? I am open to any suggestions.

Redownload the firmware file. It is corrupt.
Take note of the md5 hash of the one you have now. The hash of the one you download will be different if it is correct. Downloading over wifi can cause it if you have a bad Network Address Translator or a weak signal (full bars doesn't necessarily mean you have a good data transfer signal, it means the "hello" signal is clean and free of attenuation as good as can be).
Simply pulling the power cord for a few seconds and plugging it back in can solve the NAT issue, which is a common issue on adsl modems.
Beamed in by telepathy.

shivadow said:
Redownload the firmware file. It is corrupt.
Take note of the md5 hash of the one you have now. The hash of the one you download will be different if it is correct. Downloading over wifi can cause it if you have a bad Network Address Translator or a weak signal (full bars doesn't necessarily mean you have a good data transfer signal, it means the "hello" signal is clean and free of attenuation as good as can be).
Simply pulling the power cord for a few seconds and plugging it back in can solve the NAT issue, which is a common issue on adsl modems.
Beamed in by telepathy.
Click to expand...
Click to collapse
Excuse my ignorance but how can I install the firmware? I've tried to do it via adb but i got this error;
E: footer is wrong E: signature verification is wrong
installing via sd card won't work neither.
can you walk me through? I think I'm missing something here. please keep in mind that my phone is in bootloader loop and i can't start it.

tunceratan said:
Excuse my ignorance but how can I install the firmware? I've tried to do it via adb but i got this error;
E: footer is wrong E: signature verification is wrong
installing via sd card won't work neither.
can you walk me through? I think I'm missing something here. please keep in mind that my phone is in bootloader loop and i can't start it.
Click to expand...
Click to collapse
What happens when you power off the device and then power it on using the button combination PWR+VOLDOWN? This should put you into download mode.
Assuming that works, the SD card method should be available to you.

I can open download mode just fine, but when I try to flash i get "E:footer is wrong signature verification failed". Probably because my phone is locked, on s-on mode and not in usb debugging mode.

tunceratan said:
I can open download mode just fine, but when I try to flash i get "E:footer is wrong signature verification failed". Probably because my phone is locked, on s-on mode and not in usb debugging mode.
Click to expand...
Click to collapse
Have you redownloaded the ruu and verified it for the filesize?.
Beamed in by telepathy.

@shivadow: There is no 3.35.401.32 RUU so I assume the OP isn't talking about RUUs. @tunceratan: If you tried to flash one of Sneakyghost's firmware packs or one of the firmware packs that can be found in the no-red-text-aboot threads than it's no miracle that they fail. They are all custom made and therefore not signed by HTC. A S-ON phone like yours won't accept files that aren't signed by HTC. Not to mention that those packs don't contain a rom. So they won't help if you face a bootloop, either.
You should head to the RUU section in the ReadMe thread. There you should find all needed information. In addition you should read the article that is linked in my signature and deals with the difference between rom and firmware.

HTC 10 hard bricked

Hello everyone!
I have htc 10 hard bricked. i plug the phone to my pc and "QUSB__BULK". How can i do???
Thaks to all!!

Andoniar78 said:
Hello everyone!
I have htc 10 hard bricked. i plug the phone to my pc and "QUSB__BULK". How can i do???
Thaks to all!!
Click to expand...
Click to collapse
this may be of use?
http://www.droidsavvy.com/unbrick-qualcomm-mobiles/

Thank you for your help andybones.
I can´t do the first method because i can´t see the partitions of my phone. I had donwloaded miniton partition wizard but don´t see partitions and with hdd raw copy tool same. Don´t see partitions so i only can do the second method but i had this error:
Process Index:0
Programmer Path:C:\Users\Ando\Desktop\HTC 10\8675_W00\8675_W00\prog_emmc_firehose_8936.mbn
Image Search Path:C:\Users\Ando\Desktop\HTC 10\8675_W00\8675_W00
Please select the XML file
Patch file number is not match with raw pargram file, abort selection
Start Download
Program Path:C:\Users\Ando\Desktop\HTC 10\8675_W00\8675_W00\prog_emmc_firehose_8936.mbn
COM Port number:3
Sahara Connecting ...
Sahara Version:2
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
en QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
en QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
THANK YOU AGAIN FOR ALL!

How can you hardbrick HTC 10? im asking so I know what I should not do lol

Was my error.
I was trying to put an original rom because in Spain there is still no ruu for my free version. Find a tutorial to change cid and mid with a ruu for that mid. I made the change from cid and mid, I inserted the "ZIP" inside the SD reboot the phone and gave error. I found a ruu.exe, I ran it, gave another error. I rebooted and already DEAD!

Andoniar78 said:
Was my error.
I was trying to put an original rom because in Spain there is still no ruu for my free version. Find a tutorial to change cid and mid with a ruu for that mid. I made the change from cid and mid, I inserted the "ZIP" inside the SD reboot the phone and gave error. I found a ruu.exe, I ran it, gave another error. I rebooted and already DEAD!
Click to expand...
Click to collapse
Wrong device ruu?
Sent from my HTC 10 using XDA Labs

Yess DeeZZ_NuuZZ.
Because i put other cid and mib and download other ruu Because I did not realize it was htc one. So i can´t turn on my phone and i can´t do nothing....

Andoniar78 said:
Yess DeeZZ_NuuZZ.
Because i put other cid and mib and download other ruu Because I did not realize it was htc one. So i can´t turn on my phone and i can´t do nothing....
Click to expand...
Click to collapse
You've changed CID with sunshine ?
What kind of CID had you try ? Because I wanted to made that on my custom rom in order to have Super CID (11111111) and install the stock HTC's Ruu from EU

sanguine14 said:
You've changed CID with sunshine ?
What kind of CID had you try ? Because I wanted to made that on my custom rom in order to have Super CID (11111111) and install the stock HTC's Ruu from EU
Click to expand...
Click to collapse
Just change your phone to the below:
CID: HTC__001
MID: 2PS620000
That's the WWE one.
Edit: oh and grab the ruu for that.
Sent from my HTC 10 using Tapatalk

hello sanguine14, i had installed by CMD. the cid is good, i think is eeuu cid for put android N but mid is not ok.
Toyny, my phone WAS DIED. Black screen and do not respond. Volumen down + power NOTHING and when i plug de cable "QUSB__BULK". is died!!!!

Andoniar78 said:
Thank you for your help andybones.
I can´t do the first method because i can´t see the partitions of my phone. I had donwloaded miniton partition wizard but don´t see partitions and with hdd raw copy tool same. Don´t see partitions so i only can do the second method but i had this error:
Process Index:0
Programmer Path:C:\Users\Ando\Desktop\HTC 10\8675_W00\8675_W00\prog_emmc_firehose_8936.mbn
Image Search Path:C:\Users\Ando\Desktop\HTC 10\8675_W00\8675_W00
Please select the XML file
Patch file number is not match with raw pargram file, abort selection
Start Download
Program Path:C:\Users\Ando\Desktop\HTC 10\8675_W00\8675_W00\prog_emmc_firehose_8936.mbn
COM Port number:3
Sahara Connecting ...
Sahara Version:2
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
en QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
en QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
THANK YOU AGAIN FOR ALL!
Click to expand...
Click to collapse
https://forum.xda-developers.com/htc-10/how-to/htc-10-partition-table-t3374048 partition table for WWE phone. don't know if there is anywhere a table for sprint etc because they are different

Hello, thanks for you help but i dont know where can i put this. In linux terminal? because in cmd of windows not recognize comands. when i put in linux "No such file or directory"

Andoniar78 said:
Hello, thanks for you help but i dont know where can i put this. In linux terminal? because in cmd of windows not recognize comands. when i put in linux "No such file or directory"
Click to expand...
Click to collapse
what do you try now?

i´m trying to do this tutorial but isn´t posible!! phone to technical services...
THANK YOU FOR ALL!!!

Andoniar78 said:
i´m trying to do this tutorial but isn´t posible!! phone to technical services...
THANK YOU FOR ALL!!!
Click to expand...
Click to collapse
repair will most likely cost as much as nearly new second Hand xD because they will Change Motherboard I think, but write here if you know more

Phone hard bricked
Cro Cop said:
How can you hardbrick HTC 10? im asking so I know what I should not do lol
Click to expand...
Click to collapse
I dont get it I flashed a "signed firmware" to my HTC 10 S-on mind you and now it wont even turn on or give my qload or anything its completely dead? Is there anything I can do at all? I have tried holding down power and volume keys but nothing at all. every once in a while I may see an amber light for a split second but when I first plug in but nothing after that no Qload HS no beeps no light and no life in the phone of any kind.

Nickw1978 said:
I dont get it I flashed a "signed firmware" to my HTC 10 S-on mind you and now it wont even turn on or give my qload or anything its completely dead? Is there anything I can do at all? I have tried holding down power and volume keys but nothing at all. every once in a while I may see an amber light for a split second but when I first plug in but nothing after that no Qload HS no beeps no light and no life in the phone of any kind.
Click to expand...
Click to collapse
Your post lacks ALL the important details.
What firmware and rom version whas/is it running
What firmware EXACTLY did you flash
Do you have a carrier locked HTC10, do you have a sprint version......
Just telling us you flashed "a" firmware isn't going to cut it.
Cheers

Phone hard bricked
Mr Hofs said:
Your post lacks ALL the important details.
What firmware and rom version whas/is it running
What firmware EXACTLY did you flash
Do you have a carrier locked HTC10, do you have a sprint version......
Just telling us you flashed "a" firmware isn't going to cut it.
Cheers
Click to expand...
Click to collapse
The HTC 10 was running T-mobile but Carrier unlocked, it was S-on but bootloader or HTC dev unlocked/rooted and it had the latest OTA, firmware ETC. I used the "HTC version tool" to change the main version to 1.81.531.1, I found this firmware 2PS6IMG_1.81.531.1_firmware(Signed).zip on a thread of XDA by member named BeHold_this. I downloaded and flashed this rom in RUU mode The phone did the whole fail 90 like normal but instead of restarting RUU mode to where I am suppose to flash it a second time, it went black and never came back. Now when I plug it in to the PC, I get the amber light to flash once maybe twice but thats it I cant get even QLOAD9008 or anything en device manager it doesn't even do that? I have bricked HTCs before and gotten "Qload_HS Download 9008" and "QLOAD_BALK" I had an HTC one M7 that was stuck in "QLOAD_HS_DEBUGGING" and that one I used the "HTC Debricking project" to fix it and that phone still works to this day. but this is different. I have tried holding down every button configuration like power, Vol-up and PWR, VOL-DWN and PWR, Both VOL KEYS AND PWR and nothing not even QLOAD. IS there any magic trick to even make this thing come up in QLOAD_HS mode? Please let me know thank you.

Did pretty much the same with my U 11.
Did you solve or did you end up taking it to service?

Bricked my Vibe P1a42 with QFIL

Hi, I decided to write here, I hope you can help me out.
So today I tried to root my phone with the instructions found at https://forum.xda-developers.com/showpost.php?p=68696079&postcount=114
I checked that my build no. is S288, so with rooting there would be no data loss for me (I still backed up everything important of course)
First problem I came across was that I had to found how to download QFIL, I downloaded and installed version 1.0.0.2 I think.
Second was that I couldn't get the Qualcomm Com port to show in QFIL neither in Device Manager. I figured out that as well, by doing loads of research (googling)
I also installed ADB to help me get into the state where I see the Qualcomm port, because normally if I just power it off, and connect it to my PC, it powers on in the "charging interface"
So everything was working, I downloaded the P1a42_S288_160721_ROW_RAW_QFIL file, extracted it, filled in everything in the QFIL program and hit Download while holding the + & - buttons to enter TWRP mode or whatever it is called. It returned with this:
Code:
PROGRAM: Send raw data fail
Failed to write I:\Telefon Ment�sek\Lenovo Vibe P1\Root (2017,03,11)\P1a42_S288_160721_ROW_RAW_QFIL\recovery_twrp.img to the device
Download Fail:System.Exception: Failed to upload the emmc images to the phone using Firehose
...
Download Fail: FireHose Fail FireHose Fail
Finish Download
Sorry, I can't write down everything bc I already closed the program, so I'm writing these off of screenshots
I already tried other USB cables, other USB ports, other drivers, even other ROMS, but everytime I try, I get this message:
Code:
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
So currently I can't power on the device in any way, tried holding + and -, + and power, - and power, home and power, home power and +, home power and -, home power + -
Please help me, I would be really glad Cheers!
Also, sorry if my English is a bit poor, I'm a 15 year old boy who's native speaking lang is not English
P.S. I also don't know if I broke my warranty with this or not, because I technically have not rooted the phone, just did something else. And also, what if someone would've stolen it and I would've got it back and I wouldn't be able to turn it on because the thieves have broken it? (That is not the case right now, just asking).
PS 2: I have an alarm at 0:00 today, but I doubt that the phone is just gonna magically turn itself on for the alarm, we'll see. I may also try to leave the phone to completely discharge (I remember now why I didn't want to buy a phone with a built-in battery)
EDIT: I didn't mention, that the first time I tried to flash, I was using files from a Directory that's path contains both spaces and unknown (?) characters (é) (only unknown by the software) as seen above in the first box.

gabor6505 said:
Hi, I decided to write here, I hope you can help me out.
So today I tried to root my phone with the instructions found at https://forum.xda-developers.com/showpost.php?p=68696079&postcount=114
I checked that my build no. is S288, so with rooting there would be no data loss for me (I still backed up everything important of course)
First problem I came across was that I had to found how to download QFIL, I downloaded and installed version 1.0.0.2 I think.
Second was that I couldn't get the Qualcomm Com port to show in QFIL neither in Device Manager. I figured out that as well, by doing loads of research (googling)
I also installed ADB to help me get into the state where I see the Qualcomm port, because normally if I just power it off, and connect it to my PC, it powers on in the "charging interface"
So everything was working, I downloaded the P1a42_S288_160721_ROW_RAW_QFIL file, extracted it, filled in everything in the QFIL program and hit Download while holding the + & - buttons to enter TWRP mode or whatever it is called. It returned with this:
Code:
PROGRAM: Send raw data fail
Failed to write I:\Telefon Ment�sek\Lenovo Vibe P1\Root (2017,03,11)\P1a42_S288_160721_ROW_RAW_QFIL\recovery_twrp.img to the device
Download Fail:System.Exception: Failed to upload the emmc images to the phone using Firehose
...
Download Fail: FireHose Fail FireHose Fail
Finish Download
Sorry, I can't write down everything bc I already closed the program, so I'm writing these off of screenshots
I already tried other USB cables, other USB ports, other drivers, even other ROMS, but everytime I try, I get this message:
Code:
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
So currently I can't power on the device in any way, tried holding + and -, + and power, - and power, home and power, home power and +, home power and -, home power + -
Please help me, I would be really glad Cheers!
Also, sorry if my English is a bit poor, I'm a 15 year old boy who's native speaking lang is not English
P.S. I also don't know if I broke my warranty with this or not, because I technically have not rooted the phone, just did something else. And also, what if someone would've stolen it and I would've got it back and I wouldn't be able to turn it on because the thieves have broken it? (That is not the case right now, just asking).
PS 2: I have an alarm at 0:00 today, but I doubt that the phone is just gonna magically turn itself on for the alarm, we'll see. I may also try to leave the phone to completely discharge (I remember now why I didn't want to buy a phone with a built-in battery)
EDIT: I didn't mention, that the first time I tried to flash, I was using files from a Directory that's path contains both spaces and unknown (?) characters (é) (only unknown by the software) as seen above in the first box.
Click to expand...
Click to collapse
Dear Pls follow this link
https://forum.xda-developers.com/vibe-p1/how-to/lenovo-vibe-p1-a42-c72-root-ready-t3533693
You can see the qualcomm driver only when you switch off phone and hold Volume+/- plus power button.

I can't bc my phone won't turn on currently,
So I probably shouldn't have used ADB to get into fastboot or whatever, my phone may be broken because I tried to do the flash while in that state.
Did you read my whole post though?
The next thing I'll try then is uninstalling all the drivers and programs related to my phone, and then following the guide you suggested, because I still see the Qualcomm port, I just can't do anything with my phone.

OMG, I have waited a few hours, and just randomly thought why not try again flashing the rom (I don't think this is the right word for the QFIL Download procedure), and it worked! So I'm actually really happy I don't need to send it in to repair or try other things. I got the system I started the procedure with, so I didn't actually lost any of my files neither did I root my phone. Now to decide if I want to try again rooting it with the detailed instructions you sent or just leave it like this so I avoid getting into all this again. I think I will try again to root it lol why not
Will report back here if it was successful

I have successfully rooted my phone, and installed the Xposed Framework on my phone, so I'm really happy.
I can't really seem to find where to lock this thread so please someone lock this thread (I am not familiar with this forum, so I don't know if it is needed or not)

[GUIDE][QFIL MODE]Unbrick your Le Pro3, tested and working

All credits for this go to @tora33, c/p from here, he tested it himself, and confirmed it working.
This should bring back your bricked phone from the dead, it's a low level flash procedure, meaning don't play around with it unless absolutely necessary, IT WILL WIPE YOUR PHONE CLEAN!
Charge your mobile phone
download :
New link for qfil file Qfil_zl1_ufs
and put in C:/
download : FlashOne2.0 , put in a folder and extract it ,
run "FlashOne2.0"
How to qfil Flash
When select qfil flash type, press power key, volume up and volume down key at the same time, then the phone enter into qfil mode, connect USB cable with PC, wait for PC install driver automatically, then press ‘Refresh’ button on the tool, serial port will display on UI, select the port you want to flash, and make sure there is no other qcom device connected.
Select corresponding flash zip file, the path of zip file should not contain Chinese and special character. (Under qfil mode, the tool can’t get hardware information, you should check if the software and hardware is matching yourself.)
Press ‘Flash’ button, then start to unzip flash zip file to current folder, but if there is already a corresponding unzip file existing, ‘Decompression folder is exist, re-decompress or not?’ dialog will pop up, if select yes, will re-decompress, else not. After unzip finished, start to flash the phone automatically, and the progress bar display flashing progress, and at the same time, the flashing log will also be shown on UI.
After flash complete or error happened, a notification dialog will pop up.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Can this restore bands? I have tried everything and i cant get b20 active.

the links are death , look here

tora33 said:
the links are death , look here
Click to expand...
Click to collapse
fixed

This is very neat. Kind of like an odin-restore program for Le Pro3! Is there any way to get the stock LEX727 file for this?

the link of: le_zl1_qfil_ufs
Continue offline for me

kmkzneguin said:
the link of: le_zl1_qfil_ufs
Continue offline for me
Click to expand...
Click to collapse
New link posted

18:36:37: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
18:36:37: ERROR: function: sahara_main:854 Sahara protocol error
18:36:37: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download

If you did the process correctly, it could be a hardware problem (I hope not)

kmkzneguin said:
18:36:37: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
18:36:37: ERROR: function: sahara_main:854 Sahara protocol error
18:36:37: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
Click to expand...
Click to collapse
Hi,
I had the same error trying to revive my x727 while I was using a Qfil file provided by Tora33 on the w w w.leeco.re/topic/1906-helpx720-bricked
2017-06-11 02:18:18 QfilFlashThread >>> 02:18:17: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
2017-06-11 02:18:18 QfilFlashThread >>> 02:18:17: ERROR: function: sahara_main:854 Sahara protocol error
However, i finally succeeded with the qfil file from another link that was provided on page 2 of the leeco.re forum.
Just follow the same guidelines with the "newer" Qfil file.
One downside for me is that my x727 now thinks it is a dual sim x720
@tora33 --> Many many thanks for providing a working solution to revive our devices.

Thanks for this!
Sent from my LEX727 using Tapatalk

Can confirm that this works. It took a lot of tries to work but it did. The things that I had to try before this actually worked include: hold the button combo to get into qfil mode for like 2 minutes, use the original charging cable, use a usb 2.0 port connected to the motherboard (e.g. use the back usb ports if you're using a desktop), holding the power button for a really long time, and charging for like 2-3 hours to make sure that the phone had enough battery. It is a finicky process, but it does work. The phone, if you were on a US rom, now reads as a 720 Chinese edition. That being said, I'm just glad the phone is back up and running lol.

I think, we can flash this rom by this tool. But, name of rom needs to be very short, example 1.zip.

Incidentally.. After the phone comes back to life... Your Le Pro 3 will be running a Developer Version of EUI. However, you can install the latest version of Official EUI version. Unfortunately, the method isn't simple and requires a bit more steps.
After the flashing is successful, your Le Pro 3 may not boot automatically. Press the Power Button for a LOOOONG time... about a a minute or so... for it to leave the QFIL Mode. After a long vibration, the phone will start and will take its sweet time to boot up. Have patience.
Incidentally... after flashing and first boot... you may notice that the Internal Storage is abnormally low... about 10GB Only. A simple solution to restore the internal storage to 32GB / 64GB is by going to Backup/Restore in Settings and Factory Resetting the Phone with the "Format Virtual SD Card" Option selected.
To install the latest Official EUI download the ROM from preferably official sources... Rename the file to Update (The file should read Update.zip... not Update.zip.zip) and Paste in the phone. Using the Inbuilt File Manager.... tap on the Update.zip file and choose upgrade. If this method works... Great...
If not... You will need to Flash TWRP Recovery, Wipe EVERYTHING... and flash the ROM using a Flash Drive and after mounting USB OTG Storage.
To Flash TWRP simply shut down the phone and By Keeping the Volume Down Button Pressed Hit the Power Button to Enter the Fastboot Mode.
Thereafter... flash TWRP Recovery... Boot into TWRP Recovery... Restart TWRP Recovery... Insert the USB Flash Drive Using USB OTG Adapter... and flash the ROM using the Install Tab in TWRP Recovery.

Thanks for ultimate guide, I bricked my phone trying to root it and this guide just helped me revived my dead phone. Thanks a bunch!
Just so everyone knows, when I phone was dead, it was just dead, I pressed the power button for several min, no response, completely black screen, while putting on charge, there was no light. So no sign of life at al.
Now it's revived and I have successfully rooted and installed AICP ROM.

help!
bocondo said:
Thanks for ultimate guide, I bricked my phone trying to root it and this guide just helped me revived my dead phone. Thanks a bunch!
Just so everyone knows, when I phone was dead, it was just dead, I pressed the power button for several min, no response, completely black screen, while putting on charge, there was no light. So no sign of life at al.
Now it's revived and I have successfully rooted and installed AICP ROM.
Click to expand...
Click to collapse
Hello, I have exactly the same problem you had. How did you enter qfil mode when the smartphone was no longer responding. The software flashone me brand to re-connect me in flash mode. But the screen is still black. Thank you in advance.

help!
Hello.
I have a leeco x722. I tested everything I could find but my smartphone is still in hard brick. No reaction, no sound, no vibration, no led, no screen.
It is still detected by the software flashone in QFIL. I have tested a lot of QFIL file but it still marks me "QFIL flash failed, please re-enter into the flash mode!" I try to stay pressed on the volume and power buttons and re-flash but still the same. Would you have a trick to switch to QFIL mode by being in hard brick. Or do you have a QFIL file for x722 and not x720.
Thank you.

QFIL X722
Hey! "Accidentally" Bricked my phone on pure stupidity. Is there any QFIL for the Le Pro 3 Elite X722 I need it so badly to have a chance to bring my phone back to life.
Tried your file but im getting this error:
6:46:51: ERROR: function: rx_data:247 Error occurred while reading from COM port
06:46:51: ERROR: function: sahara_main:854 Sahara protocol error
06:46:51: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
Thanks in advance

konevolan said:
Hey! "Accidentally" Bricked my phone on pure stupidity. Is there any QFIL for the Le Pro 3 Elite X722 I need it so badly to have a chance to bring my phone back to life.
Tried your file but im getting this error:
6:46:51: ERROR: function: rx_data:247 Error occurred while reading from COM port
06:46:51: ERROR: function: sahara_main:854 Sahara protocol error
06:46:51: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
Thanks in advance
Click to expand...
Click to collapse
Did you solve this problem? I made the same error with the X722 and am in exactly the same situation.
Qfil gives the same error. In an attempt, Qfil was able to download FireHose, but content.xml was in error. After that, I could no longer get Qfil down Firehose. And now this message always appears.
I already know that it is possible, just not how to get around this problem of Qfil.

after do that my storage show 9gb after format data and stock rom install and again formad sd card vs... but i cant up the storage more than 20gb
when i install the stock rom it show i have 32gb storage but computer says 19gb
i installl omni rom its says 24gb and comouter says 19gb again i stuck here what cani do ?