Develop Bugs

[Q] Won't get past fastboot no animation logo

You're all probably thinking "Oh he is stuck in a recovery loop and here's how you get out of it."
This all starts with the fact that I'm trying to use Kindle Fire Utility to root my device. However the normal circumstance is that it must boot into fastboot but in my case it is impossible to get past fastboot no animation and just sits there. I've been trying to my research on how to do this but I can't seem to find an answer for this. I've already told my computer to boot it back into normal mode via ubuntu with the fastboot command "fastboot -i 0x1949 oem idme bootmode 4000" and it works fine that puts me back in normal mode past the no-animation screen.
So I'm still trying to get rid of this fastboot recovery loop that still persists. I've already restored back into stock rom and the same problem persists. Has anyone have had this experience and successfully the eliminated the loop problem?
In a similar circumstance is that if I have my normal cable or factory cable plugged into between my machine and the kindle, it does the same issue and does not get past no-animation part.
I'm guessing it comes down to the fact that there is a misconfigured setting on the kindle regarding TWRP perhaps. I would appreciate ANY help whatsoever. I want to eliminate this stupid problem. Now, remember, I am able to get back into normal mode via ubuntu with the above command line so that isn't the issue here. The issue is this fastboot / does not get past no-animation stage that I want to fix.
EDIT: I've resolved this. I was missing the fff bootloader which was causing all of my issues in the first place. Sorry for wasting your time looking at this.

Bootloader locked, cannot enable OEM

Hello,
long story short: I have no OS installed on my LG G4 (H815) and get the "This device is not trusted and will not boot" screen when trying to boot normally. I have Android N bootloader. I can get to fastboot and download mode, but:
I cannot flash anything through fastboot as I don't have OEM enabled and I cannot enable it since I have no Android on the phone
LG UP stops at 23% (or 11%) of uploading full, new OS when the phone is in the Download Mode. The device is connected to a proper port reported as COM3.
LG Flash Tool doesn't work at all, maybe I'm using it wrong way?
"fastboot devices" reports the device connected correctly
"fastboot getvar unlocked" gives me a simple "no". I had the bootloader unlocked before, I have no idea what happened, I only did a factory reset from that time (and that caused the loss of system, too...)
Is there anything I can do to unbrick this phone? I couldn't find anything to match my problem so I'm writing here. If anything is unclear or you need more info just ask, please.
EDIT: Found my solution in this post. Thread can be closed, I hope that this solution will work for everyone.

MOTO G6 - Qualcomm - EDL Mode

Hi,
I'm after some advice, how do I place the Moto G5 in Qualcomm mode or EDL mode.
I have entered the bootloader by holding down and turning the phone on, this allows me to use fastboot.
From there I can scroll down to QCOM, but when I press the power button it boots into the normal system instead of EDL mode.
I have also attempted from within fastboot to use:
fastboot oem edl
fastboot oem qcom-on
fastboot reboot emergency
and
fastboot reboot-edl
Although non of these have been sucessful.
I also have access to an EDL cable, although, when I plug the phone in, then flick the switch 10 seconds later, it does not enter EDL mode, it just charges.
The phone sometimes shows as File Storage Linux USB Gadget in device manager, although it is inaccessible, I have updated the laptop to use the qualcomm drivers, although I don't think it will ever recognise it if I can't put the phone into qualcomm mode to begin with.
Any help would be much appreciated.

What are you actually attempting to do?
This mode is generally used to unbrick a device but you have access to the bootloader/fastboot mode and you wouldn't use edl mode to unbrick this device anyway
It's also used on some device to unlock the bootloader but again you wouldn't do that with this device
So without knowing what you are trying to achieve I can't give you any advice
Technically if you start the phone normally then enable usb debugging in dev options then connect phone to PC and in a terminal window where you have adb set up type
adb reboot edl
Not all devices support this mode though and I've no idea if this one does

TheFixItMan said:
What are you actually attempting to do?
This mode is generally used to unbrick a device but you have access to the bootloader/fastboot mode and you wouldn't use edl mode to unbrick this device anyway
It's also used on some device to unlock the bootloader but again you wouldn't do that with this device
So without knowing what you are trying to achieve I can't give you any advice
Technically if you start the phone normally then enable usb debugging in dev options then connect phone to PC and in a terminal window where you have adb set up type
adb reboot edl
Not all devices support this mode though and I've no idea if this one does
Click to expand...
Click to collapse
Without going into too much detail as to why, there are tools I have access to which can be used to take a full back up of the entire memory block of the phone when it is in Qualcomm mode.
I cannot access adb on the device to use "adb reboot edl" so I am limited to either trying to activate Qualcomm using a button combination or via fastboot, unless you can advise another way.
Any help or a point in the right direction would be much appreciated.

jameswstubbs said:
Without going into too much detail as to why, there are tools I have access to which can be used to take a full back up of the entire memory block of the phone when it is in Qualcomm mode.
I cannot access adb on the device to use "adb reboot edl" so I am limited to either trying to activate Qualcomm using a button combination or via fastboot, unless you can advise another way.
Any help or a point in the right direction would be much appreciated.
Click to expand...
Click to collapse
Sounds dodgy to me - sounds like you're trying to access data from a phone that isn't yours so I won't be helping

TheFixItMan said:
Sounds dodgy to me - sounds like your trying to access data from a phone that isn't yours so I won't be helping
Click to expand...
Click to collapse
It's not dodgy, but I fully understand.
Thank you anyway.

try fastboot -i 0x2b4c oem ​​reboot-edl (it's working for LENOVO ZUK Z1 and ZUK Z2)

You can try (if you can/have the TWRP image) to flash TWRP and in reboot options select EDL.
In case the bootloader isn't unlocked you can also use fastboot boot [TWRP image name] to boot directly into TWRP without flashing and then repeat, go into reboot options and select edl.
Not sure if it works for you, if it does let me know that I have helped!

TheFixItMan said:
Sounds dodgy to me - sounds like you're trying to access data from a phone that isn't yours so I won't be helping
Click to expand...
Click to collapse
I need help too. So, I own a Moto G5s plus sanders. I unlocked its bootloader the day I got it. Didn't keep any backup and rooted it. I Also installed dot os based on android 11. But my 4G Volte connection was finicky. So, I decided to use a Volte zip patch. But, anyways I flashed the zip via TWRP and tried to reboot. But the phone didn't turn on after that. After a few minutes to my shock I understood that I hardbricked my mobile. No button combos, nothing worked. Anyways in my desperation I found a YouTube video showing the use of blankflash to revive a phone and lo and behold I used the procedure to again restore my device. It booted to the fastboot interface. But my happiness was short lived. My baseband was unknown at this point and the bootloader was I dunno downgraded to 0.5 inplace of 2.12. But, more importantly the unlock status was lost. I unlocked it again and all went well. I could even flashed TWRP. but then I realised I couldn't upgrade my bootloader. I couldn’t do anything. It's always gives a "security downgrade", "preflash validation failed" and "permission denied" error. I even tried RSA official rescue tool from Lenovo but even it was unsuccessful. It was never unsuccessful before that. Not even with a unlocked bootloader. I researched for days and tried custom ROMs. I flashed stock images. Nothing brought back my baseband and IMEI. When I type "fastboot oem unlock critical" it gives me permission denied error with a message. "Need OEM signed bootloader." I think the blankflash bootloader is the root of all evil. I need to change it and therefore I need to enter the edl mode. I have tried all adb commands and fastboot commands. The phone reboots okay after those commands but never goes into edl mode whatsoever. I am also ready to do a controlled hardbrick of my device to go into the edl mode so that I can use my device again with a proper bootloader and a properly working fastboot. Please help

Stuck in fastboot mode. How do I exit it?

Hey guys, I am currently stuck. I followed this guide: https://forum.xda-developers.com/t/...cept-g710tm-with-photos.4168771/post-87030237. Now, my phone won't boot. It'll show a "Your device can't be checked for corruption. Lock the bootloader." message, then immediately reboot back into the fastboot mode. I have attached a video of my phone doing this:

How can I get it to stop doing this?

Bootloading Kyocera DuraXV Extreme

Hello, I'm having some serious trouble bootloading my Kyocera DuraXV Extreme (AOSP)
I've went into developer options and activated USB debugging and allowed OEM unlocking.
But I get stuck on rebooting into bootloader mode. I've tried different approaches:
1. Starting up phone while holding volume up and down buttons. Then select "reboot to bootloader".
2. adb reboot bootloader command
Both options reboot the phone without going into bootloader mode.
Seems Kyocera decided to somehow lock the bootloader mode. Anyone know of a workaround here?

jonas.sj said:
Hello, I'm having some serious trouble bootloading my Kyocera DuraXV Extreme (AOSP)
I've went into developer options and activated USB debugging and allowed OEM unlocking.
But I get stuck on rebooting into bootloader mode. I've tried different approaches:
1. Starting up phone while holding volume up and down buttons. Then select "reboot to bootloader".
2. adb reboot bootloader command
Both options reboot the phone without going into bootloader mode.
Seems Kyocera decided to somehow lock the bootloader mode. Anyone know of a workaround here?
Click to expand...
Click to collapse
My comments below are based on the belief that you are trying to unlock the bootloader.
I am not familiar with this phone but generally the two steps mentioned by you are not enough to unlock the bootloader. After those steps, you'll have to issue a command via adb to unlock the bootloader and if successful, then you can boot into it for further operations. The command will vary between devices, so search and profit.

Thanks, this cleared it up a bit, you are right, I'm trying to unlock it.
I'm trying the command fastboot flashing unlock but only getting the message < waiting for any device >. I read somewhere that I might need some USB drivers but I don't know where to find them. I have the latest version of the standard USB drivers for the phone, but as I understand it I need special drivers for this?

I'm trying to follow the steps here: https://www.ifixit.com/Guide/How+to+unlock+the+bootloader+of+an+Android+Phone/152629#s317298
I get stuck on the step:
Enter the command adb reboot bootloader
Wait a couple seconds until your device rebooted into the bootloader, then enter the command fastboot flashing unlock
My phone isn't "rebooted into the bootloader", it just reboots. It gives the message "< waiting for any device >" when I write fastboot flashing unlock

jonas.sj said:
I'm trying to follow the steps here: https://www.ifixit.com/Guide/How+to+unlock+the+bootloader+of+an+Android+Phone/152629#s317298
I get stuck on the step:
Enter the command adb reboot bootloader
Wait a couple seconds until your device rebooted into the bootloader, then enter the command fastboot flashing unlock
My phone isn't "rebooted into the bootloader", it just reboots. It gives the message "< waiting for any device >" when I write fastboot flashing unlock
Click to expand...
Click to collapse
It should be a driver issue. When the phone is on and you connect it to the PC/laptop and send the command 'adb devices', does it show an alphanumeric value? Likewise, when you are booted into the bootloader by key combination and send the command, 'fastboot devices', does it show the same alphanumeric response? If so, the drivers are installed properly. If not, either you don't have the correct drivers or they are not installed properly. Try installing the drivers again after disabling driver signing in Windows on your PC (search for it on Google).

Hello, can you clarify what you mean by "booted into the bootloader by key combination"?
My problem is I cannot boot into bootloader at all.
Any attempt at doing so results in a normal boot of the device.

jonas.sj said:
Hello, can you clarify what you mean by "booted into the bootloader by key combination"?
My problem is I cannot boot into bootloader at all.
Any attempt at doing so results in a normal boot of the device.
Click to expand...
Click to collapse
Are you sure that the key combination for booting into bootloader is what you described in the first post?
1. Starting up phone while holding volume up and down buttons. Then select "reboot to bootloader".
Click to expand...
Click to collapse
I see Power plus Volume Up as the suggested one from a Google search. Try that.
If you can't even boot into the bootloader with the correct key combination, I don't know how to help you further since we are starting to go in circles. I am sorry.

Hello, thank you so much for trying to help me. It seems I can't boot into bootloader. Volume up + power gives the same result as what I did before.: It opens a "Recovery" menu where I can choose reboot to bootloader, but this option just reboots the phone.
I've been in contact with Kyocera and they say:
Thanks for contacting the Kyocera Customer Support. We will be more than happy to assist you with your concern
In this case allow us to inform you that since this device is a basic phone , it doesn't have the option to activate fastboot mode. By installing something that will change the way the phone works , that will void the warranty that came with the phone. We as manufacture can not help you to modify the software that came with the phone.
So the phone's fastboot mode has been deactivated. But since it's an android I guess it should still be possible with some workaround. I just don't know whee to start, I've been researching for a week with no result.

Something interesting ehre, maybe someone with more coding knowledge can tell what's going on.
I found the source code for the phone and located a file called recovery.c which I guess handles the menu I see when I press volume up + power button. Maybe some clue to why the phone isn't going into fastboot mode?