I broke my device, I cannot flash rom in fastboot , and I found a solution by removing the battery, connecting two points and then connecting the device to PC to show me " Qualcomm HS-USB QDLoader 9008 " appeared to me but it does not appear in miflash or any another flash tool
cescer4 said:
I broke my device, I cannot flash rom in fastboot , and I found a solution by removing the battery, connecting two points and then connecting the device to PC to show me " Qualcomm HS-USB QDLoader 9008 " appeared to me but it does not appear in miflash or any another flash tool
Click to expand...
Click to collapse
Please Help Me
Related
I have TOT files, I have BoardDiag (different versions), but when I follow the countless instructions online I always get "Device was not found in dload trying flash programmer.".
Where do I go from here?
Bro how are conecting your phone ..
If it is like ...
1: you installed the drivees for qualcome qhs bulk ..
2: device when conected now show under device manager as Qualcomm HS-USB QDLoader 9008
3:if above two are effermative tell me !! If not thwn again tell me...???
Check ure ports in d3vice manager
bravo2526 said:
Bro how are conecting your phone ..
If it is like ...
1: you installed the drivees for qualcome qhs bulk ..
2: device when conected now show under device manager as Qualcomm HS-USB QDLoader 9008
3:if above two are effermative tell me !! If not thwn again tell me...������
Click to expand...
Click to collapse
This is correct. I reinstalled the qualcomm driver, now it is COM3 and boarddiag from here works (http://open-freax.fr/guide-unbrick-your-lg-g3/), but emmc test fails.
"Failed to open partition from EMMC." It doesn't matter if I select Read/Write or Erase.
By the way, I didn't have to open my phone for the 9008 mode, it went there kind of on its own.
Quza said:
This is correct. I reinstalled the qualcomm driver, now it is COM3 and boarddiag from here works (http://open-freax.fr/guide-unbrick-your-lg-g3/), but emmc test fails.
"Failed to open partition from EMMC." It doesn't matter if I select Read/Write or Erase.
By the way, I didn't have to open my phone for the 9008 mode, it went there kind of on its own.
Click to expand...
Click to collapse
Bad news if emmc fails ..i supose its a hardware damage to your emmc chip ...
What was you trying when it happend ..?
Power outage during rom installation ??
During KDC flash it stopped working. After 15 minutes at 0% I restarted the phone.
On the button does not respond in rekaveri vhodit.Pri not connected to the notebook , in the Device Manager recognized as Qualcomm HS-USB QDLoader 9008
Device:NOKIA XL(RM-1030)
sw_4081 said:
On the button does not respond in rekaveri vhodit.Pri not connected to the notebook , in the Device Manager recognized as Qualcomm HS-USB QDLoader 9008
Device:NOKIA XL(RM-1030)
Click to expand...
Click to collapse
Couldn't understand your question
It is impossible to restore the phone.
P.S:English is not know , we have to translate the suggestions through Google translator
Did anyone managed to unbrick his lg g3 in following mode and how ?
No boot, No recovery, No fastboot or download mode working, phone is completely in dead boot state,
and is recognized as lge androidnet usb serial port, when connected to PC
not as Qualcomm HS-USB QDLoader 9008 ,
kindly help me if you can.
thank you
aeroexpert said:
Did anyone managed to unbrick his lg g3 in following mode and how ?
No boot, No recovery, No fastboot or download mode working, phone is completely in dead boot state,
and is recognized as lge androidnet usb serial port, when connected to PC
not as Qualcomm HS-USB QDLoader 9008 ,
kindly help me if you can.
thank you
Click to expand...
Click to collapse
Search in this forum about "Qualcomm 9008".
But you need to disassembly a little parts of your phone and... you need a little piece of wired.
Good Luck!:good:
Hi,
My 10 is hard bricked. I was connected to pc standart usb c cable pc shows "Qualcomm HS-USB Diagnostic 900E" and i was connected to pc EDL cable, shows "Qualcomm HS-USB QDloader 9008". But i don't have QFIL rom for this phone. Anyone have it? or anyway stock files convert to QFIL rom?
Sorry my english :angel:
Up!
Go to HTC if your phone still have warranty
So,
Now I got the issue that was the main culprit of the error happening while flashing in EDL mode through mi flash tool .. .
Current status of my phone- Nothings working no buttons working
Black screen
When I connect to PC blue led flashes. Without battery red led flashes only one time
Phone detects as Qualcomm HS USB qdloader 9008 port
And after that when I try to flash it .. the port kepps refreshing and the phone connects and disconnects...
On the device manager it seems that the qdloader 9008 converts into diagonastics 9006 then reverts back to 9008. And in the disk management the Qualcomm mmc storage do the same just connects and 2 or 3 second later disconnects. Then reconects and disconnects..
And at that point the flash tool gives the error....
Changing usb wire and changing pc gives the same result .
Now please suggest me a way to get rid out of it.
The thread is very long sorry for that ....
Please help me out .
Windows driver issue maybe?
Are you sure that this is not a driver problem in Windows?
I have never tried flashing in Download Mode, but I'm just making a (possibly silly) guess.
Enable Test-signing in Windows and try again :-
Put this command in an elevated command prompt and restart the computer to enable test signing:-
Code:
bcdedit /set testsigning on
Good luck!
First trying with disable driver signature enforcement from boot option and now tried with cmd ran the code but same result. Is this my windows 7 problem?
I haven't tried it on windows 10....