Listening to music I have no problem with sound, but when someone calls and I take the call through the headunit I can barely hear them. Anyway fix to this problem?
In the factory advanced settings (the 126 password) there is a tab for various volumes - radio, music, bluetooth, phone etc. Check the values there in case phone or bluetooth are set too low.
Which volume is necessary to increase?
Changing bluetooth volume in that menu has no effect on calls, and there is no option like "voice" or "phone". Anyone else figure this out? It's almost unusably quiet even at maximum volume. The slightest road noise makes the other party inaudible.
Are you're front channels connected?
On some of these chinese units bluetooth phone audio as well as nav audio is routed to the front channels only.
Related
Hi all,
Just got me a Sony DR-BT10CX bluetooth stereo headset. I'm new to these things, so I have a bit of a newbie question. The sound is quite good, much better than the ones that came with my HTC Touch (obviously), but there's a considerable static in the background, that seems to increase when I increase volume, but only when regulated on the headset itself. If I increase volume on my Touch (in WMP, or volume slider), the static doesn't seem to increase. I was just wondering if this is normal in these headsets? This headset sells in Holland for just under E100,-, so not really expensive, but not really low end either. Could it be a faulty headset or crappy design?
All thoughts and experiences very welcome...
Thanks,
Driekus
A2DP question
Might be a silly question, but have you tried turning the volume on the Touch up to 80% and turning the headset's hardware volume setting down??
Some A2DP stereo headsets have a particular setting they work best at..
Failing that, you may simply have a headset with firmware that really isn't perfectly compatible with your PDA...
Good luck,
Andy
www.pressdigital.com.au
Support Team
As a matter of fact the volume on my touch is currently up to 100% as is the one in WMP, so that I can keep the volume setting on my headset low, but that's not really how it should work I think. Besides, incoming calls are now very low volume, so I have to adjust the volume on the headset everytime a call comes in (and quickly lower it when I hang up in order to prevent hearing loss...) and I tend to miss appointment-announcements by MS Voicecommand because of this as well.
I guess the headset isn't perfectly compatible with my Touch, as sound sometimes skips (which is even more annoying because it doesn't happen all the time) and my pda doesn't automatically connect to my headset (solved with A2DP-plugin, see http://forum.xda-developers.com/showthread.php?p=1503123#post1503123), but I'm not sure whether the background hiss is because of this too.
I recently received a replacement Galaxy Nexus (my original power button broke). I am having an issue with the new phone where my old phone worked fine--and I think I have found a solution that may help others if they are having this problem.
When listening to media, either music via PowerAmp or podcasts via DoggCatcher, the ringtone for an incoming call is reduced to a point that is almost inaudible. I can tell there is an incoming call, because the media stops, but that is unacceptable. If I stop the media but keep the ringer at the same volume, an incoming call rings at a much louder (and satisfactory volume). For some reason, playing media is reducing the volume of the ringtone.
I found a solution that seems to be working for me. I noticed that while adjusting volumes in the volume settings control panel, the volume would be reduced but adjusting the volume would return it to normal. To solve the problem I set up a tasker profile that will adjust the volume on the event of an incoming call. The tasker profile looks like this:
Context: Event > Phone Ringing, Hardware > Headset Plugged (otherwise I think this would make vibrate worthless)
Task: Ringer Volume: Level 2 (anything else seems much too loud, but I will have to try it out).
Anyone else having this problem? Know the cause? Other solutions?
Hello,
I do not use the phone feature very often, but recently I had to take some calls while driving and could hardly understand what the other person is saying, because the speaker phone volume is really low.
Now, of course I set the volume to max and checked every setting I could find related to phone calls. I even went into the service menu and did the speaker tests. There I realized that the speaker phone is using a different speaker as the one that is used to play back music or other sounds. The same sound sample is used in the tests and it is much softer in the speaker phone test compared to the mono or stereo speaker tests.
Is there any hack, setting or configuration file change I can do to use the mono or stereo speaker for the speaker phone feature?
Please help, this is the only gripe with this fine phone I have.
Same problem here.
Solutions, anyone?
UP
I rarely make calls in my car, so I do not know if this was much of an issue on my older head unit*, or if it was a symptom prior to root.
I have a new unit from Pumpkin - MTC8-KLD6-V2.81
Rooted with Malaysk's latest ROM
My phone (HTC M8) is connected through bluetooth. Music plays just fine through the system.
When I make a call, however;
1) Music Stops and head unit goes silent (not a problem)
2) I hear a bit of static (I have had low volume static since I upgraded to Malaysk if the head unit is on and nothing is playing)(again, not really a problem)
3) Phone starts to make a call.
4) Static suddenly goes away, as if the volume was suddenly turned down
5) I can barely hear the phone ring through the head unit.
I have tried turning up the volume all the way on the phone (volume on the phone seems to do nothing when in a bluetooth call) and turning up the head unit. If I have the head unit all the way up, I CAN hear reasonably well, but that's at a volume of 30 when everything else plays loud enough at 5.
I have looked for different setting on the phone and on the head unit and have found nothing. I have adjusted the Factory Settings -> Audio, but that changes bluetooth as a whole and make the music play too loud.
I would say that the issue is is similar to switching the phone from "regular" (where 1-10 is set for being near one's ear) to "speaker" (where 1-10 can be heard across the room) and the phone is telling the head unit to stay at "regular".
Actually, on my first head unit the problem was just the opposite and phone calls were always way too loud.
Anyone have ideas on other settings I should try?
Thanks
I think there are options in the factory settings are for individual volume controls.
singlecell83 said:
I think there are options in the factory settings are for individual volume controls.
Click to expand...
Click to collapse
There are, but the option is for "Bluetooth" in general.
Bluetooth itself is fine, and I can listen to music from my phone through Bluetooth at whatever level I choose. The problem is that when it switches to phone (dialing out or coming in) the volume drops drastically and I have to turn the head unit's volume up all the way to hear at all. That means the music from Bluetooth will come back at speaker (or at least ear) damaging levels once the call ends.
If adjusting the BT volume is not enough, test with others volume settings lowering/raising some of them.
the norm is the hands free on these units are not the best and there are some mods out there on the forum..
I am having an issue where when attached to my Bluetooth in my car I can not adjust my in-call volume in my phone. It gets stuck at 50%. I can adjust media volume no problem when playing music and can adjust the in-call volume in other Bluetooth devices like my buds+ and galaxy watch.
Any ideas how to fix this? It results in either very quiet call volume or when the call ends the music is crazy loudly.
I have this same issue.
Me too
Don't suppose anyone has managed to resolve this yet? It's still happening with me with Android 11 update.
Disabled absolute volume?
Make sure volume limiter is not enabled.
Clear system cache.
Reset network settings.
I have the same problem on tcl 55p83 ( RT851)
bluetooth max volume is limited to 50%
Any help ?
I have the same issue.... Just figured it was normal to keep distortion or feedback at a minimal?? But, maybe it isn't?