Related
So, I've got a 64gb black sprint Galaxy S6, non-edge. This morning, it had stock 5.11 on it, but I decided I wanted to root it, and ... I screwed up. I got Odin 3.10.6 and installed CF-Auto-Root-zerofltespr-zerofltespr-smg920p.tar.md5 which I now know does not work with 5.11. Since then, bootloop. Reboots every minute or so. I've tried everything I can find, wiping everything, flashing what purport to be stock ROMs, putting TWRP on there, and still within a minute of booting it reboots. I tried installing Smart Switch, but it can't get a connection because the phone just won't stay booted.
Rooting would be nice, but I just want my phone to work again. What can I do here? I don't have insurance and KNOX is flipped.
if you're sure you are on 5.1.1, flash any kernel (unikernel v8, etc.) that would fix your issue.
I should mention this is a SM-G920P, if that's significant.
I flashed the stock package through Odin, then TWRP, then installed Hacker Kernel through that. It's still rebooting repeatedly while i try to go through the initial setup process, and dumping me at the language select each time.
I tried unikernel too, didn't work either.
Okay, here's my current process, which is not working.
Boot to ODIN/Download mode, by holding power+volume down+home.
Open Odin 3.10.6, as administrator. Auto-Reboot is unchecked.
Flash what's supposed to be the latest stock rom, obtained here.
Wait until it says PASS, then reboot into ODIN mode again.
Flash the TWRP 2.8.7.0 tar, obtained here.
Wait until it says PASS, then reboot into recovery, by holding power+volume down+home until it reboots and then power+volume up+home to enter recovery.
Wipe Data/Cache/Darvik.
Transfer Hacker Kernel and SuperSU .zips, obtained here, to storage on phone.
Use TWRP to install Hacker Kernel, as instructed on that page.
Reboot into recovery.
Use TWRP to install Super SU. Note: In the section of the log reading Boot Image Patcher, I get Extracting ramdisk, Decompressing ramdisk, Failure, aborting. Important?
Reboot.
Now it's sitting on the Samsung Galaxy S6 screen, and not going any farther than that.
I tried flashing nothing but the stock 5.1.1 package, but that's not working either. It still keeps rebooting, and it won't ever get past the screen that says "Preparing your device for first-time use... This may take 3 or 4 minutes." Is there anything I can do? I can't afford to not have a phone and I can't afford to replace this one. Please, help me.
I've redownloaded everything, checking md5 sums, and those are all correct. Flashing the BOL1 stock gets me rebooting, flashing it and then Unikernel v8 gets me rebooting, flashing it and then Unikernel v9 gets me rebooting, flashing it and then Unikernel v9 and then TWRP has me rebooting.
It boots up and stays up for a minute or two, enough to get a little ways into the setup. The first boot, it stays on the Sprint screen for a while, then reboots after about a second on the language select screen. When it gets back there, I can select language, connect to wifi, accept the EULA, and then wait on the "Preparing your device for first-time use" screen for a little while before it reboots. Sometimes it'll get as far as asking me if I want to let Google collect diagnostic data.
Hardware issue...i had the same issue with similar process. I had to get a replacement phone
Is it possible that trying to install the Chainfire root package on a 5.11 phone just broke something permanently? Could it be something partition-related, maybe? I'm at a total loss here.
This should help
kafziel83 said:
Is it possible that trying to install the Chainfire root package on a 5.11 phone just broke something permanently? Could it be something partition-related, maybe? I'm at a total loss here.
Click to expand...
Click to collapse
I had the same issue also with the SM-G920P.
Problems:
*unikernal > v6 (v7 and above == bootloop)
*hackerkernal on non-teamsprint rom == bootloop
*cf auto root was not required for root
What fixed it for me:
1. Odin back to stock 5.1.1
2. Flash TWRP
3. Boot into recovery
4. Reboot (it should tell you that root is not installed or something like that, so if it asks to install root let it)
5. Once booted into os SuperSU will tell you to update the su binary, update then reboot
6. Congratulations you have root.
lodbldbol said:
I had the same issue also with the SM-G920P.
Problems:
*unikernal > v6 (v7 and above == bootloop)
*hackerkernal on non-teamsprint rom == bootloop
*cf auto root was not required for root
What fixed it for me:
1. Odin back to stock 5.1.1
2. Flash TWRP
3. Boot into recovery
4. Reboot (it should tell you that root is not installed or something like that, so if it asks to install root let it)
5. Once booted into os SuperSU will tell you to update the su binary, update then reboot
6. Congratulations you have root.
Click to expand...
Click to collapse
Did 1, did 2, did 3, did 4 but it didn't give any message like that, and now it's just repeating the "Samsung Galaxy S6 Powered By Android" screen over and over.
Unless when you say "Odin back to stock 5.1.1" you mean flashing 5.1.1 and then going through the setup to a functioning OS, because I have never been able to do that since I started.
kafziel83 said:
Did 1, did 2, did 3, did 4 but it didn't give any message like that, and now it's just repeating the "Samsung Galaxy S6 Powered By Android" screen over and over.
Unless when you say "Odin back to stock 5.1.1" you mean flashing 5.1.1 and then going through the setup to a functioning OS, because I have never been able to do that since I started.
Click to expand...
Click to collapse
To Odin back to stock 5.1.1 properly follow the steps on this page exactly with the files it tells you to use http://www.androidrootz.com/2015/05/how-to-unroot-galaxy-s6-and-s6-edge.html
Then you'll need a ROM, i recommend this http://forum.xda-developers.com/spr...ment/ram9200-ofe-rom-thread-v3-5-1-1-t3173417
Once in recovery flash it (skip to step 7 in the link) then boot up, if that doesn't work I don't know what will.
Tried that, now it boots as far as the Sprint screen but hangs there and then reboots.
kafziel83 said:
Tried that, now it boots as far as the Sprint screen but hangs there and then reboots.
Click to expand...
Click to collapse
Hardware issue
Any advice on getting a replacement? I still have about $500 left on the monthly installments for this phone, and I don't have insurance. The Sprint stores I went to said to go to Samsung for a replacement for a malfunctioning phone, since I've had it for less than a year, since KNOX is flipped I'm guessing Samsung won't give me a thing.
I uploaded a file to Mediafire called 2016-03-20--04-15-35_G920P_Renegade_OJ7_v1.zip
This is a TWRP backup of my phone's system/radio/boot/efs, it should replace anything that doesn't work. I don't know if it'll work but it's worth a try.
Copy the zipped folder to TWRP/BACKUPS and restore your phone
Okay. Can you link to the mediafire page to download it?
kafziel83 said:
Okay. Can you link to the mediafire page to download it?
Click to expand...
Click to collapse
No, XDA won't let me put links to outside websites until I have 10 posts.
Same Problem
kafziel83 said:
Okay. Can you link to the mediafire page to download it?
Click to expand...
Click to collapse
Hi,
Same problem here,
Did you find a solution for your problem?
lodbldbol said:
I uploaded a file to Mediafire called 2016-03-20--04-15-35_G920P_Renegade_OJ7_v1.zip
This is a TWRP backup of my phone's system/radio/boot/efs, it should replace anything that doesn't work. I don't know if it'll work but it's worth a try.
Copy the zipped folder to TWRP/BACKUPS and restore your phone
Click to expand...
Click to collapse
If ever the EFS is cleared, deleted whatever. It re-builds from block 12, so there's no need to worry too much.
Sent from my SM-G925P using XDA Labs
---------- Post added at 10:12 AM ---------- Previous post was at 10:09 AM ----------
kbashiri said:
Hi,
Same problem here,
Did you find a solution for your problem?
Click to expand...
Click to collapse
I would do a quick repartition, nand erase all, flash stock ROM boot it, and flash from there. Hope it goes well.
Sent from my SM-G925P using XDA Labs
Please Help
ChubbbySquish said:
If ever the EFS is cleared, deleted whatever. It re-builds from block 12, so there's no need to worry too much.
Sent from my SM-G925P using XDA Labs
---------- Post added at 10:12 AM ---------- Previous post was at 10:09 AM ----------
I would do a quick repartition, nand erase all, flash stock ROM boot it, and flash from there. Hope it goes well.
Sent from my SM-G925P using XDA Labs
Click to expand...
Click to collapse
Should I do re-partition then nand erase all and then flash rom or should I do them altogether?
Good evening everyone!
I've recently wanted to update my Hercules from 4.1 (I know it's reeealy outdated) to version 6.0 Marshmallow.
So I did a few steps and now I cant' seem to go any further, and I need your help.
So far, I've done the following:
-Installed TWRP 2.8.7.0
-Used Odin to flash the TWRP mentioned above
Now, I know there are a few problems regarding this version of the TWRP on the Hercules, so I tried fixing it by using Odin again and flashing the updated 2.8.7.1 and even the 3.0 version that I found on some threads, but with no sucess.
I haven't even had the chance to install Marshmallow on my phone in the first chance, because I couldn't find any .ZIP folders on the TWRP instalation menu.
I really appreciate your help guys, I'm a noob at this and I'm just starting to figure what is what, I just need my phone updated. It's running so far atleast, so it's not hard bricked I guess.
Did you follow the instructions to flash TWRP using Odin?
olafo73 said:
Did you follow the instructions to flash TWRP using Odin?
Click to expand...
Click to collapse
I'm pretty sure I did everything I was intended to do. I installed Samsung Kies so I could install the drivers on my mobile, and then TWRP through Odin properly with the blue light showing up. After flashing it, it turned green and said PASS or PASSED. So I think I did everything right on that end, I can even access TWRP with no real problems.
I even tried to do a ROOT on my system, but again, I couldn't use ZIP or any other files on the TWRP installation option because they simply do not appear
bump
Watching this thread as I have the same problem.
I can boot to TWRP 2.8.7, but if I try to install, there's no file to install from.
I can go back to TWRP 2.6.0, and then mount the card and see the ROM, but every ROM I try fails. Something about non-virtual partitions if I try 4.4 or better, and error executing updater binary if i try 4.1
aguycalled80 said:
Watching this thread as I have the same problem.
I can boot to TWRP 2.8.7, but if I try to install, there's no file to install from.
I can go back to TWRP 2.6.0, and then mount the card and see the ROM, but every ROM I try fails. Something about non-virtual partitions if I try 4.4 or better, and error executing updater binary if i try 4.1
Click to expand...
Click to collapse
How did you go back to TWRP 2.6.0?
N1ZUW said:
How did you go back to TWRP 2.6.0?
Click to expand...
Click to collapse
With Odin.
I can boot in download mode no problem.
N1ZUW said:
Good evening everyone!
I've recently wanted to update my Hercules from 4.1 (I know it's reeealy outdated) to version 6.0 Marshmallow.
So I did a few steps and now I cant' seem to go any further, and I need your help.
So far, I've done the following:
-Installed TWRP 2.8.7.0
-Used Odin to flash the TWRP mentioned above
Now, I know there are a few problems regarding this version of the TWRP on the Hercules, so I tried fixing it by using Odin again and flashing the updated 2.8.7.1 and even the 3.0 version that I found on some threads, but with no sucess.
I haven't even had the chance to install Marshmallow on my phone in the first chance, because I couldn't find any .ZIP folders on the TWRP instalation menu.
I really appreciate your help guys, I'm a noob at this and I'm just starting to figure what is what, I just need my phone updated. It's running so far atleast, so it's not hard bricked I guess.
Click to expand...
Click to collapse
I don't know of any problems with any of the recoveries. However there are different recoveries for different roms which need to be used in a specific order and in a specific way, the first time that you virtually repartition your phone.
Have you gone through the process of applying the "virtual partition" and installing the modified "virtual partition" recovery? This is required for most of the MM roms on this phone (Hercules). The process is very well documented here http://forum.xda-developers.com/galaxy-s2-tmobile/help/guidance-sgh-t989-updating-issue-t3414641 in the #2nd post.
markusrow said:
I don't know of any problems with any of the recoveries. However there are different recoveries for different roms which need to be used in a specific order and in a specific way, the first time that you virtually repartition your phone.
Have you gone through the process of applying the "virtual partition" and installing the modified "virtual partition" recovery? This is required for most of the MM roms on this phone (Hercules). The process is very well documented here http://forum.xda-developers.com/galaxy-s2-tmobile/help/guidance-sgh-t989-updating-issue-t3414641 in the #2nd post.
Click to expand...
Click to collapse
Hi, thanks for replying
No, I dont' take I have taken that step actually. I'm pretty new to this and I tried following every step correctly, but I know that I failed or skipped something at some extent and I've been trying to figure out what exactly, so I can fix it. I guess I need to Virtual Partition my phone then, could you post me the link do to so? Because I think you posted one that would take back to this post
aguycalled80 said:
With Odin.
I can boot in download mode no problem.
Click to expand...
Click to collapse
How do you go in download mode if you have TWRP installed? Does TWRP work as download mode aswell? Thanks for your help man, hope you can fix your phone too!
N1ZUW said:
How do you go in download mode if you have TWRP installed? Does TWRP work as download mode aswell? Thanks for your help man, hope you can fix your phone too!
Click to expand...
Click to collapse
I shut it down in TWRP then hold volume down and power to go into download mode.
My phone has gone backwards now though - it doesn't matter what I load in Odin now, it won't boot up. The SAMSUNG screen is on, with a progress bar, but it never gets to the end. It stops right near the end and it sits there until I reboot it again.
I have a brand new Pixel XL from Verizon that I received today and was successful in unlocking. However, I tried to root and now I am stuck on bootloop. I cannot post in DEVELOPMENT because I haven't posted here in years (haven't had ANDROID in a while). Can anyone help? I am able to access via fastboot (I believe) but I must be flashing the wrong images. I don't want to brick this nice new day-old device. I have been at it for 5 hours via research on my own, but now I am looking for someone that can help me via P.M. or what it may take. I really want to get back to enjoying this device! Thanks in advance!
bdsuser said:
I have a brand new Pixel XL from Verizon that I received today and was successful in unlocking. However, I tried to root and now I am stuck on bootloop. I cannot post in DEVELOPMENT because I haven't posted here in years (haven't had ANDROID in a while). Can anyone help? I am able to access via fastboot (I believe) but I must be flashing the wrong images. I don't want to brick this nice new day-old device. I have been at it for 5 hours via research on my own, but now I am looking for someone that can help me via P.M. or what it may take. I really want to get back to enjoying this device! Thanks in advance!
Click to expand...
Click to collapse
Read the third post in the thread below to get set up and back to stock. Then we will work on root. If you tried to root and you bootlooped it then you used the wrong SU.
https://forum.xda-developers.com/pixel/help/stupidly-bootloop-help-t3554242
1. Download a ROM. A stock version is probably in the forums somewhere if that's what you want.
2. Download TWRP image and zip from the TWRP thread.
3. Download SuperSU from the SuperSU thread.
4. Download a vendor image. There's no "official" vendor image thread AFAIK, but you can grab one from the Pure Nexus rom thread. NMF26V is compatible with all 7.1.1 ROMs & stock.
Now you have two options:
Fast: Put the ROM, TWRP(zip only), SuperSU and vendor image on USB flash drive, then connect the USB 3 to USB C adapter to your flash drive. Don't connect it to the phone yet. An external HDD/SSD should also work if that's all you've got.
Slow: While in TWRP(Instructions below) push the ROM, TWRP(zip only), SuperSU and vendor image files to your phone through ADB with "adb push C:\file_path\ /sdcard/" sans quotes. You will need to do this for each file, or alternatively push a folder containing the four files. adb file transfer is very slow.
5. Boot your phone to the bootloader, and connect it to your computer. This can be achieved by holding volume down and power from an off state.
Note: If your device is still bootlooping you won't be able to get to the bootloader. Hold volume up and power until the device shuts off to get out of the bootloop temporarily, then boot to bootloader.
6. In a command window, "fastboot boot twrp.img"
7. Connect your flash drive to your phone if you chose that option, or push the files through adb if you chose that option
8. Flash TWRP zip, ROM and vendor image. STAY IN TWRP
9. Return to TWRP's home screen > advanced > file manager. Scroll down until you see 'fstab.marlin'(in the root '/' directory). Tap on 'fstab.marlin' and delete it. Skipping this step means SuperSU won't install.
10. Flash SuperSU zip, reboot to system and you're done.
SDK
TonikJDK said:
Read the third post in the thread below to get set up and back to stock. Then we will work on root. If you tried to root and you bootlooped it then you used the wrong SU.
https://forum.xda-developers.com/pixel/help/stupidly-bootloop-help-t3554242
Click to expand...
Click to collapse
Just thought I'd update you...And I know I sound like I have no idea what I'm doing but traditionally I've never had issues like this But I am trying to get ADB to show the flash-all command. The one I have installed doesn't show that feature so I can't follow the tutorial. If you have a direct link to what I may be missing I would appreciate it otherwise I will update you once I figure it out.
bdsuser said:
Just thought I'd update you...And I know I sound like I have no idea what I'm doing but traditionally I've never had issues like this But I am trying to get ADB to show the flash-all command. The one I have installed doesn't show that feature so I can't follow the tutorial. If you have a direct link to what I may be missing I would appreciate it otherwise I will update you once I figure it out.
Click to expand...
Click to collapse
The link to the proper adb and fastboot are in the post i pointed you to.
Help with root and TWRP
TonikJDK said:
The link to the proper adb and fastboot are in the post i pointed you to.
Click to expand...
Click to collapse
Thanks for your assistance. I now have root installed and I think I'm good except for one thing. I keep thinking TWRP is installed but for some reason when I reboot to bootloader, then select reboot recovery mode, it takes me to android recovery. I am used to recovery taking me to TWRP. I know TWRP works but I feel like I'm temporarily flashing it each time or something. I even installed the twrp app and I see I can flash zips that way, etc, but I wanted to know if you knew how to make the phone boot to TWRP in recovery? Or is that necessary?
bdsuser said:
Thanks for your assistance. I now have root installed and I think I'm good except for one thing. I keep thinking TWRP is installed but for some reason when I reboot to bootloader, then select reboot recovery mode, it takes me to android recovery. I am used to recovery taking me to TWRP. I know TWRP works but I feel like I'm temporarily flashing it each time or something. I even installed the twrp app and I see I can flash zips that way, etc, but I wanted to know if you knew how to make the phone boot to TWRP in recovery? Or is that necessary?
Click to expand...
Click to collapse
I dont do it that way on this phone. TWRP and SU are modifying the same parts of the phone, and there are cases where it could conflict. Rare, not a big deal, but since i don't need TWRP installed i don't.
To install it ypu first boot to it.
Fastboot boot twrpFilename.
Then from within TWRP you install the TWRP zip.
Make sure it is TWRP RC1
All set
Thanks again for your help. I am running pure ROM as I mentioned and I seem to like it. Do you K or if Franco works with Pure or do you have a suggestion on a good rom/kernel? Is there anything else that you can suggest I should be using with the new phone? I remember there used to be tools that you could install that allowed you to customize the system even further but the name escapes me. . Is there anything like that or even a theme tool which is a must have when you are rooted and running custom roms? No big deal if not. Very happy with where I stand now. Really appreciate you getting me back up and running!
You are most welcome. I don't ROM so I don't know what kernels work with what roms for sure. But my understanding is that they are all pretty universal. I run stock with Franco.
Other than that i dont mod much. Ad blocker, black themes and a few adjustments to Franco.
TonikJDK said:
You are most welcome. I don't ROM so I don't know what kernels work with what roms for sure. But my understanding is that they are all pretty universal. I run stock with Franco.
Other than that i dont mod much. Ad blocker, black themes and a few adjustments to Franco.
Click to expand...
Click to collapse
Perfect! Thanks yet again. Have a great remainder of the day!
bdsuser said:
Thanks again for your help. I am running pure ROM as I mentioned and I seem to like it. Do you K or if Franco works with Pure or do you have a suggestion on a good rom/kernel? Is there anything else that you can suggest I should be using with the new phone? I remember there used to be tools that you could install that allowed you to customize the system even further but the name escapes me. . Is there anything like that or even a theme tool which is a must have when you are rooted and running custom roms? No big deal if not. Very happy with where I stand now. Really appreciate you getting me back up and running!
Click to expand...
Click to collapse
Im running pure and elementalx with excellent results.
?Tapped from my pure pixelXl?
have you ever seen an issue where the phone boots to twrp even though everything was working fine? It starts happening if I do a restart. Then no matter what it boots into TWRP unless I wipe again? I believe it's happening after I flash root but I'm going out of my mind with trial and error. Any help would be appreciated.
bdsuser said:
have you ever seen an issue where the phone boots to twrp even though everything was working fine? It starts happening if I do a restart. Then no matter what it boots into TWRP unless I wipe again? I believe it's happening after I flash root but I'm going out of my mind with trial and error. Any help would be appreciated.
Click to expand...
Click to collapse
HELLO!!! I understand any frustrations you may be having, as the pixel devices have changed a good bit for us as far as development. Anyways. I'm just going to throw some knowledge out there, then proceed to help get you up and running!
You couldn't post in the development section because of your post count, but even if you could, it would have been in the wrong section and it would have been removed, or moved to the questions section.
Also, I see someone has pointed it out earlier, but I'll say it again just to make sure everything is clear. The command you were running "fastboot boot TWRP.img" only boots TWRP temporarily. You are suppose to have two files, one IMG file and one zip file. You boot the IMG file, then once you're in TWRP, you flash the zip file, then reboot to recovery and you will have installed TWRP properly.
With root, flashing wrong files or using the outdated root method will cause boot loops. The correct way to root (again already been said) is the get TWRP up and running, delete the fstab file (see earlier post) then flash SuperSU and reboot. Just throwing this out there Incase someone comes across it, if you manage to boot loop your device due to to rooting, you can fastboot flash franco's kernel and it will fix the bootloop (,but you won't have root) this isn't the correct way to fix it, but it will get you back up and running without downloading the large factory image.
***About to edit this post to continue giving more info***
Here is a correct guide and good template to get you running.
start by flashing a clean factory image, then let it boot and get it set up.
Reboot to fastboot, fastboot boot TWRP IMG then flash TWRP zip using the latest versions (RC1 is latest, pm me for more info).
Reboot the phone to recovery to ensure TWRP stuck.
Go-to advanced, file manager in TWRP and find the fstab.marlin file and delete.
Then you can go ahead and flash the latest SuperSU (I use 2.79 sr3) and when it's done reboot to system and verify root.
After rooting you can go ahead and flash a kernel if you want, I use elemental which you can flash in TWRP, but see the kernel instructions prior to flashing.
Reboot and you have a nice stock ROM with root and kernel.
For flashing Roms, kind of follow the same template, most Roms require you to flash part of or the whole latest factory image.
If your on a clean install, go ahead and install TWRP as mentioned above.
Then use TWRP to install whatever ROM you want per ROM developer instructions.
Side note, some Roms replace the TWRP with cwm or stock recovery, so it's always nice to flash the TWRP zip after flashing a ROM.
After flashing ROM, boot to system to make sure all is well, then boot back to recovery and follow instructions above for root/kernel.
As far as the problem you're having now, it usually comes from flashing outdated SuperSU images. Do a search for 2.79 sr3 and use it to root (pm me if you need help)
You might have to start clean one more time, And flash factory image.
noidea24 said:
HELLO!!! I understand any frustrations you may be having, as the pixel devices have changed a good bit for us as far as development. Anyways. I'm just going to throw some knowledge out there, then proceed to help get you up and running!
You couldn't post in the development section because of your post count, but even if you could, it would have been in the wrong section and it would have been removed, or moved to the questions section.
Also, I see someone has pointed it out earlier, but I'll say it again just to make sure everything is clear. The command you were running "fastboot boot TWRP.img" only boots TWRP temporarily. You are suppose to have two files, one IMG file and one zip file. You boot the IMG file, then once you're in TWRP, you flash the zip file, then reboot to recovery and you will have installed TWRP properly.
With root, flashing wrong files or using the outdated root method will cause boot loops. The correct way to root (again already been said) is the get TWRP up and running, delete the fstab file (see earlier post) then flash SuperSU and reboot. Just throwing this out there Incase someone comes across it, if you manage to boot loop your device due to to rooting, you can fastboot flash franco's kernel and it will fix the bootloop (,but you won't have root) this isn't the correct way to fix it, but it will get you back up and running without downloading the large factory image.
***About to edit this post to continue giving more info***
Here is a correct guide and good template to get you running.
start by flashing a clean factory image, then let it boot and get it set up.
Reboot to fastboot, fastboot boot TWRP IMG then flash TWRP zip using the latest versions (RC1 is latest, pm me for more info).
Reboot the phone to recovery to ensure TWRP stuck.
Go-to advanced, file manager in TWRP and find the fstab.marlin file and delete.
Then you can go ahead and flash the latest SuperSU (I use 2.79 sr3) and when it's done reboot to system and verify root.
After rooting you can go ahead and flash a kernel if you want, I use elemental which you can flash in TWRP, but see the kernel instructions prior to flashing.
Reboot and you have a nice stock ROM with root and kernel.
For flashing Roms, kind of follow the same template, most Roms require you to flash part of or the whole latest factory image.
If your on a clean install, go ahead and install TWRP as mentioned above.
Then use TWRP to install whatever ROM you want per ROM developer instructions.
Side note, some Roms replace the TWRP with cwm or stock recovery, so it's always nice to flash the TWRP zip after flashing a ROM.
After flashing ROM, boot to system to make sure all is well, then boot back to recovery and follow instructions above for root/kernel.
As far as the problem you're having now, it usually comes from flashing outdated SuperSU images. Do a search for 2.79 sr3 and use it to root (pm me if you need help)
You might have to start clean one more time, And flash factory image.
Click to expand...
Click to collapse
There is absolutely no need to delete the fstab file anymore. That only needed to be done when TWRP was still alpha 2, and almost three versions of su earlier.
ALL roms replace TWRP with stock recovery unless you are using lineage then you will get Cyanogenmod recovery, so reflashing TWRP before booting into system is a must.
If you are flashing root and or custome kernel and end up in a bootloop, flashing the stock boot.img to both slots via:
'fastboot flash --slot _a boot boot.img'
'fastboot flash --slot _b boot boot.Img'
will fix the issue and you will be able to boot up just fine. Again you will have to reboot into TWRP from the bootloader and reflash the zip. When you are done flashing the boot.img's you might as well just
'Fastboot boot TWRP-file.img'
Then install the zip!
Hi,
Googled a while and looked around in the forum but did not find anyone with the exact same issue as me so here goes.
Maybe someone could tell me where exactly I am doing wrong.
I have a LG Nexus 5X, latest Oreo 8.1 official update.
I want to install a custom kernel to improve performance and/or battery life.
Never rooted or anything like that so I googled around to know what to do.
So I unlocked the bootloader and flashed the latest TWRP custom recovery (v3.2.1-0).
The first strange thing unlike what I kept reading in tutorials and forums is that, although I did reboot directly into recovery after flashing TWRP, and completed flashing TWRP using its interface, I was never able to reboot into TWRP unless I flashed it again. As if TWRP could not avoid being overridden by the stock recovery. So to get back to TWRP I always have to:
reboot into the bootloader: adb reboot bootloader
flash TWRP: flash recovery twrp-3.2.1-0-bullhead.img
reboot bootloader: fastboot reboot
immediately start into to bootloader (power + vol down)
choose 'Recovery Mode' from there
Which seemed odd, that TWRP wouldn't 'stick', although I was not root yet.
Which gets me to the second part. All I wanted was to root my phone.
So after not finding a consistent way to do it - it seemed every website I visited gave me slightly different instructions to do so, I took the chance and did the following:
download latest SuperSU flashable zip file (v2.82) and copy it to internal storage
go through the process I describe in the list above to get into TWRP
install SuperSU zip file (via Install TWRP option, logs seemed ok, warned me it would take a while to boot again)
reboot, wait until it boots
But the phone got stuck in the boot screen - OS does not start to load - for at least half an hour.
Luckily, probably because the OS did not load, TWRP was not overridden and so I have access to it.
My main problem at this point is that, as a newbie on this, I am not sure what can I do in TWRP to try to restore the OS.
I have tried to restore a Nandroid backup I performed before all this, and also tried to Wipe Data / Cache and Dalvik.
Both did not work - OS still won't load.
What can I do at this point? Wipe System partition? Wouldn't that delete my Nandroid backup?
Maybe 'sideload' (not sure if the right term) an official google image for my Nexus?
Sorry again if questions like this can be easily found around the forum, but from the threads I checked I did not bump into the exact same scenario...
Thank you in advance
So in the meantime I have wiped system partition, no success either.
Ended up restoring my Nandroid backup and sideloading the latest OTA from Google, which successfully restored my phone.
Of course TWRP was overridden once again.
So back to the start: can anybody help me out on the best way to permanently flash TWRP and root the phone?
Thanks!
Forget SuperSU - Use Magisk to root your phone. As for TWRP getting overwritten - any time you take an update from Google, it will generally (if not always) restore the stock recovery. The way to get around that is to download the entire current update from Google and then use fastboot to flash the individual parts (system.img / boot.img / radio.img / vendor.img)
jbaumert said:
Forget SuperSU - Use Magisk to root your phone. As for TWRP getting overwritten - any time you take an update from Google, it will generally (if not always) restore the stock recovery. The way to get around that is to download the entire current update from Google and then use fastboot to flash the individual parts (system.img / boot.img / radio.img / vendor.img)
Click to expand...
Click to collapse
Well yes, the last time I expected TWRP to be gone since I have applied the whole image, and I wouldn't expect otherwise. My problem is that TWRP is always getting overridden each time I reboot my phone. Do you have any idea why?
Regarding Magisk, I will look around to see how to use it. Could you point me in the right direction?
Also I think I read somewhere that the kernel I wanted to flash in the end - Franco's Kernel - required SuperSU and did not work with Magisk. Am I wrong?
disacrol said:
Well yes, the last time I expected TWRP to be gone since I have applied the whole image, and I wouldn't expect otherwise. My problem is that TWRP is always getting overridden each time I reboot my phone. Do you have any idea why?
Regarding Magisk, I will look around to see how to use it. Could you point me in the right direction?
Also I think I read somewhere that the kernel I wanted to flash in the end - Franco's Kernel - required SuperSU and did not work with Magisk. Am I wrong?
Click to expand...
Click to collapse
Here's the guide stickied that should walk you through the TWRP install. https://forum.xda-developers.com/nexus-5x/general/guides-how-to-guides-beginners-t3206930
Just curious you are using "fastboot flash recovery ....." and not "fastboot boot recovery...."? The "boot" method doesn't do the install.
As for Magisk. There is a whole forum dedicated to it - https://forum.xda-developers.com/apps/magisk - Short story install the latest stable version (16.0) and call it good. I haven't had any issues with recent kernel builds including Franco, EX, etc.... One thing to keep in mind is that Magisk always gets flashed after the kernel install as it does some patching of the boot.img as part of its process.
jbaumert said:
Just curious you are using "fastboot flash recovery ....." and not "fastboot boot recovery...."? The "boot" method doesn't do the install.
Click to expand...
Click to collapse
Yes, flash, not boot.
Thanks a bunch for all your help. I didn't meant to be lazy to start by reading sticked topics, but it's so much new information for a newbie that I didn't exactly know where to start. Thanks again for sharing the links.
I'm not sure if you got this fixed. But if not, first fastboot boot twrp. Then flash supersu or magisk. Then boot back into the bootloader from twrp and fastboot flash twrp. That'll solve the problem.
Sent from my [device_name] using XDA-Developers Legacy app
jd1639 said:
I'm not sure if you got this fixed. But if not, first fastboot boot twrp. Then flash supersu or magisk. Then boot back into the bootloader from twrp and fastboot flash twrp. That'll solve the problem.
Click to expand...
Click to collapse
I tried that but I'm getting no luck with SuperSU, always gets me in a bootloop (actually, technically not a loop since it remains Frozen with the Google logo)
I'll give magisk a try and come back with feedback. Maybe it has something to do SuperSU incompatibility with Oreo 8.1..
disacrol said:
I tried that but I'm getting no luck with SuperSU, always gets me in a bootloop (actually, technically not a loop since it remains Frozen with the Google logo)
I'll give magisk a try and come back with feedback. Maybe it has something to do SuperSU incompatibility with Oreo 8.1..
Click to expand...
Click to collapse
What version of super su are you using? Use 2.82 SR 3 or 5
Sent from my [device_name] using XDA-Developers Legacy app
jd1639 said:
What version of super su are you using? Use 2.82 SR 3 or 5
Click to expand...
Click to collapse
V2.82 Stable, not Service Release. Is the last stable not compatible with Oreo? Official website is not specific about it, so I just assumed it was ok.
disacrol said:
V2.82 Stable, not Service Release. Is the last stable not compatible with Oreo? Official website is not specific about it, so I just assumed it was ok.
Click to expand...
Click to collapse
3 or 5 work on Oreo. I'm not sure about stable. I don't use it.
Sent from my [device_name] using XDA-Developers Legacy app
SR5 worked like a charm. I just wish there was a compatibility matrix somewhere in their website to avoid so many forum threads and misinformation on the subject and avoid all the hustle. The whole process is dead simple but it took me days and tailored help from you guys to figure this one out.
Thanks again to all of you for your assistance.
i had that issue with a nex 6 and flashing supersu fixed it. when i got a 6p i tried the same and get stuck on the boot logo and had to sideload factory firmware to get back to go. i have a 5x on the way maybe i will try magisk.
so after i flash twrp reboot the bootloader, i open twrp and flash supersu sr5 and all is well, no more disappearing act for twrp and no more stuck on the "google"?
Hey everyone,
I have been trying to root my new Samsung A5 (A520W - Canadian variant) but nothing seems to be working.
My first method was to flash CF AUTO ROOT with Odin, but this just rebooted the device without any sign of changing anything - no superSU installed and RootChecker returning negative results
I then flashed TWRP, and from there tried installing both SuperSU and Magisk v16.0, both of these options made the phone unusable (verification error on boot) so I flashed back to stock firmware and now I'm out of ideas.
I've tried looking for guides on the SM-A520F (non-Canadian variant) but most of these are out of date with respect to the recent OTA upgrade to nougat and/or mention the CF AUTO ROOT method which I know doesn't work
has anyone here managed to root this device? Am I missing a step, like formatting/wiping data beforehand or something? is it worth downgrading to an earlier android version?
Cheers!
dan.tjones said:
Hey everyone,
I have been trying to root my new Samsung A5 (A520W - Canadian variant) but nothing seems to be working.
My first method was to flash CF AUTO ROOT with Odin, but this just rebooted the device without any sign of changing anything - no superSU installed and RootChecker returning negative results
I then flashed TWRP, and from there tried installing both SuperSU and Magisk v16.0, both of these options made the phone unusable (verification error on boot) so I flashed back to stock firmware and now I'm out of ideas.
I've tried looking for guides on the SM-A520F (non-Canadian variant) but most of these are out of date with respect to the recent OTA upgrade to nougat and/or mention the CF AUTO ROOT method which I know doesn't work
has anyone here managed to root this device? Am I missing a step, like formatting/wiping data beforehand or something? is it worth downgrading to an earlier android version?
Cheers!
Click to expand...
Click to collapse
Format data with the FORMAT DATA button first in TWRP then immediately flash Magisk (preferred) or latest Supersu.
Reboot.
dan.tjones said:
Hey everyone,
I have been trying to root my new Samsung A5 (A520W - Canadian variant) but nothing seems to be working.
My first method was to flash CF AUTO ROOT with Odin, but this just rebooted the device without any sign of changing anything - no superSU installed and RootChecker returning negative results
I then flashed TWRP, and from there tried installing both SuperSU and Magisk v16.0, both of these options made the phone unusable (verification error on boot) so I flashed back to stock firmware and now I'm out of ideas.
I've tried looking for guides on the SM-A520F (non-Canadian variant) but most of these are out of date with respect to the recent OTA upgrade to nougat and/or mention the CF AUTO ROOT method which I know doesn't work
has anyone here managed to root this device? Am I missing a step, like formatting/wiping data beforehand or something? is it worth downgrading to an earlier android version?
Cheers!
Click to expand...
Click to collapse
Just wondering how you flashed TWRP (which version) and how? I'm having the same issue trying to get root on this phone and will probably just flash a custom
jermzii said:
Just wondering how you flashed TWRP (which version) and how? I'm having the same issue trying to get root on this phone and will probably just flash a custom
Click to expand...
Click to collapse
I have done it! Had the same problem and yes i have the Canadian a520w. I had to use Odin and then install superuser
Step one: Is to download Odin on pc mac or linux.
Step two: download superuser on your phone then move the file from your phone to
you computer.
Step three: open Odin and select the superuser zip file and it should say pass.
Step four: install root checker off Google play
This is not a full tutorial on how to install it but all you need to search is how to use Odin.
I got it!!
jermzii said:
I got it!!
Click to expand...
Click to collapse
Glad you got it to work did you use my method?
ashyx said:
Format data with the FORMAT DATA button first in TWRP then immediately flash Magisk (preferred) or latest Supersu.
Reboot.
Click to expand...
Click to collapse
Can you please provide a link to an appropriate TWRP version for SM-A520W?
Many thanks!
---------- Post added at 09:47 PM ---------- Previous post was at 09:45 PM ----------
SlickSneeker said:
I have done it! Had the same problem and yes i have the Canadian a520w. I had to use Odin and then install superuser
Step one: Is to download Odin on pc mac or linux.
Step two: download superuser on your phone then move the file from your phone to
you computer.
Step three: open Odin and select the superuser zip file and it should say pass.
Step four: install root checker off Google play
This is not a full tutorial on how to install it but all you need to search is how to use Odin.
Click to expand...
Click to collapse
Please excuse my being a layman in this matter. I tried tot flash superuser.zip using ODIN but ODIN does not even see zip files (it only recognizes some other formats like .tar, .img etc). Could you please give a little more details on how you flashed superuser.zip using ODIN?
Thanks a lot in advance.
jermzii said:
I got it!!
Click to expand...
Click to collapse
Hi jermzii,
I apologize for my questions - I am not very experienced in all these. I would like to ask you a few questions:
Where did you get an appropriate TWRP version for SM-A520W?
Also, ODIN, does not "see" zip files. How did you flash the supersu.zip using ODIN?
Many thanks for your help in advance.
I just bought a Canadian A520W with with stock Nougat (Telus firmware A520WVLS2BRD2). I tried to root it using CF autoroot and TWRP and I had the exact experience as the OP dan.tjones. There is no TWRP specifically for A520W. After trying several versions I found one which is successfully flashed with ODIN (TWRP 3.2.1.0 for A520F). TWRP appears to install Magisk (latest version 16) successfully but it shows no root or su binary. TWRP also appears to install SuperSU zip (there is a specific version for A520W nougat) successfully, but when I open SuperSU app, it says the SU binary is occupied. Google shows two "fixes" ((1) clean uninstall using an option within SuperSU, then reinstall, and (2) uninstall SuperSU + install an earlier version of SuperSU then updating the binary (hangs). Both fixes do not work. Someone mention wiping DATA in TWRP would fix the problem, but it did not work for me.
The major problem seems to be KNOX keep saying "failed verification". At one point it was so screwed up that it just boot-loop / hang and the only thing that work was download mode. I install TWRP again and it sticks. Then I wiped everything (cache/ Dalvik, data, system, internal storage). I probably could try to flash the stock nougat firmware using ODIN, but it was still downloading (snail speed free download).
Since there is no more OS in the phone, I manage to install a 6.0.1 pre-rooted custom ROM using TWRP (I originally intended to downgrade from 7 to 6.0.1 anyway because of reports of poor battery life), and installation was successfully, giving me root. BTW I originally tried to downgrade from stock nougat to stock marshmellow using ODIN, but it does not work ("failed" message).
The TWRP version that I flashed with ODIN:
TWRP 3.2.1.0 for A520F ("recovery_a5y17lte-080318.img.tar")
https://androidfilehost.com/?fid=890129502657588962
The 6.0.1 custom ROM I installed with TWRP:
AXES ROM v.1 (they did say it is compatible with A520W)
https://forum.xda-developers.com/samsung-a-series-2017/development/rom-t3606231
I did not find any nougat custom ROM suitable for A520W. I am happy that I can find a rooted ROM and it does not matter to me whether it is marshmellow or nougat.
slim_thumb said:
I just bought a Canadian A520W with with stock Nougat (Telus firmware A520WVLS2BRD2). I tried to root it using CF autoroot and TWRP and I had the exact experience as the OP dan.tjones. There is no TWRP specifically for A520W. After trying several versions I found one which is successfully flashed with ODIN (TWRP 3.2.1.0 for A520F). TWRP appears to install Magisk (latest version 16) successfully but it shows no root or su binary. TWRP also appears to install SuperSU zip (there is a specific version for A520W nougat) successfully, but when I open SuperSU app, it says the SU binary is occupied. Google shows two "fixes" ((1) clean uninstall using an option within SuperSU, then reinstall, and (2) uninstall SuperSU + install an earlier version of SuperSU then updating the binary (hangs). Both fixes do not work. Someone mention wiping DATA in TWRP would fix the problem, but it did not work for me.
The major problem seems to be KNOX keep saying "failed verification". At one point it was so screwed up that it just boot-loop / hang and the only thing that work was download mode. I install TWRP again and it sticks. Then I wiped everything (cache/ Dalvik, data, system, internal storage). I probably could try to flash the stock nougat firmware using ODIN, but it was still downloading (snail speed free download).
Since there is no more OS in the phone, I manage to install a 6.0.1 pre-rooted custom ROM using TWRP (I originally intended to downgrade from 7 to 6.0.1 anyway because of reports of poor battery life), and installation was successfully, giving me root. BTW I originally tried to downgrade from stock nougat to stock marshmellow using ODIN, but it does not work ("failed" message).
The TWRP version that I flashed with ODIN:
TWRP 3.2.1.0 for A520F ("recovery_a5y17lte-080318.img.tar")
https://androidfilehost.com/?fid=890129502657588962
Before flashing custom ROM (in zip format), I use TWRP to wipe everything on the phone (cache / Dalvik, data, system, internal storage).
The 6.0.1 custom ROM I installed with TWRP:
AXES ROM v.1 (they did say it is compatible with A520W)
https://forum.xda-developers.com/samsung-a-series-2017/development/rom-t3606231
I did not find any nougat custom ROM suitable for A520W. I am happy that I can find a rooted ROM and it does not matter to me whether it is marshmellow or nougat.
Click to expand...
Click to collapse
You have rooted the device successfully the first time when you flashed magisk.Just root manager app was not installed.
If you have screwed up your device, do a clean flash of OS...then flash twrp and after flashing magisk the binary would be flashed but the app would
not be installed.To do that extract the app from the magisk zip that you flashed.It must be in common folder inside the zip.
Dont flash binaries on top of binaries.
Hope it helps
dan.tjones said:
Hey everyone,
I have been trying to root my new Samsung A5 (A520W - Canadian variant) but nothing seems to be working.
My first method was to flash CF AUTO ROOT with Odin, but this just rebooted the device without any sign of changing anything - no superSU installed and RootChecker returning negative results
I then flashed TWRP, and from there tried installing both SuperSU and Magisk v16.0, both of these options made the phone unusable (verification error on boot) so I flashed back to stock firmware and now I'm out of ideas.
I've tried looking for guides on the SM-A520F (non-Canadian variant) but most of these are out of date with respect to the recent OTA upgrade to nougat and/or mention the CF AUTO ROOT method which I know doesn't work
has anyone here managed to root this device? Am I missing a step, like formatting/wiping data beforehand or something? is it worth downgrading to an earlier android version?
Cheers!
Click to expand...
Click to collapse
hey...im novice at this as well but I did get my a520w rooted with su on oreo with twrp...I flashed the latest su on twrp....twrp was hard to get on but there is somewhere that shows how...good luck
A Very Possible and Precise Solution
dan.tjones said:
Hey everyone,
I have been trying to root my new Samsung A5 (A520W - Canadian variant) but nothing seems to be working.
My first method was to flash CF AUTO ROOT with Odin, but this just rebooted the device without any sign of changing anything - no superSU installed and RootChecker returning negative results
I then flashed TWRP, and from there tried installing both SuperSU and Magisk v16.0, both of these options made the phone unusable (verification error on boot) so I flashed back to stock firmware and now I'm out of ideas.
I've tried looking for guides on the SM-A520F (non-Canadian variant) but most of these are out of date with respect to the recent OTA upgrade to nougat and/or mention the CF AUTO ROOT method which I know doesn't work
has anyone here managed to root this device? Am I missing a step, like formatting/wiping data beforehand or something? is it worth downgrading to an earlier android version?
Cheers!
Click to expand...
Click to collapse
Hey Sir!
Soooooo I've been messing around with this all night and I figured it out somehow after nearly frying my new A5 (2017) lol
I'd recommend that you follow the directions as best you can and as fully to help you not have to redo all your software settings and stuff like I did haha. I think if all this is done in this order you shouldn't have to lose your data. I can't guarantee anything but figured I could share what worked for me. BONUS: I actually don't have an unlocked phone and I'm still locked to my carrier actually! So I don't think all these warnings are necessarily valid. Anyhow, hope it helps. :laugh:
NOTE: I'm not allowed to post website links here for some reason haha so sorry for the inconvenience! All the sites began with the https colon double slash btw! So MAKE SURE to add that to the addresses below (links are in italics)!
FIRST: Completely backup phone using Android Studio as can be found at Tech Republic website /article/how-to-create-a-full-backup-of-your-android-device-without-root/ . Also I'd recommend you do a Smart Switch full backup. Smart Switch will work to some extent and I personally restored from there pretty intact as I didn't have the Android Studio backup option before my phone got wrecked by the Verification error after I attempted to flash SuperSU onto the phone using TWRP.
1. BEFORE ANYTHING ELSE: Enable Developer Mode (by tapping on the Build Number several times), Turn OEM unlock on, enable USB debugging, and make sure all the "factory reset block" is off (or Allow factory reset option is on) and encrypted data features are off, I unlocked any Notes and disabled Secure Folder and Knox and Samsung Pass
2. Turn phone off
3. Boot phone into Custom OS install mode by holding Power+Volume Up+Home
4. I downloaded a TWRP installer file from tx5.androidfilehost.com/dl/TLLV1I5jSqS9Zg68RNh1hA/1538776061/890129502657588962/recovery_a5y17lte-080318.img.tar
5. Download the Odin software to flash TWRP onto your device, I got mine from drive.google.com/file/d/0B-2yp-J_x0LPaGJrSUlUcHE1a2s/view
6. Used Odin 3.1 to flash TWRP onto Recovery using the AP function, also turned Auto Reboot and F.Restart off (unchecked boxes)
7. Downloaded (newest file that's a zip) such as no-verity-opt-encrypt-6.0.zip from build.nethunter.com/android-tools/no-verity-opt-encrypt/ and put it on the SD card in the phone
8. Turned phone off and booted it into Recovery Mode by holding Power+Volume Down+Home
9. Used TWRP recovery to flash the no-verity-opt-encrypt-6.0.zip which sort of disables all the security things on Samsung (such as Health and Pass and Auto Updates) that would block your work, and this actually lets you reboot your phone instead of getting the Verification Integrity Check failed error and having to reset your phone every time.
10. After rebooting my phone, everything was running fine. I then downloaded SuperSU file SR5-SuperSU-v2.82-SR5-20171001224502.zip from download.chainfire.eu/1220/SuperSU/SR5-SuperSU-v2.82-SR5-20171001224502.zip?retrieve_file=1
11. Used TWRP in Recovery Mode to flash SuperSU onto phone from SD card and hit Reboot. Slight boot loop was visible and then the phone restarted normally with SuperSU installed and full root access. Thanks be to God.
Again, I can't guarantee this will work BUT it is the first walkthrough that I know of on the web. Hope it helps at all!
Edit:
Originally gave up on this, but recently managed to flash TWRP.
Now in Verification Error on boot, and trying to flash the no-verity to get around that.
Success (almost rooted, but shouldn't be much harder)
Just flashed a custom OS using Odin_3.12.3, twrp-3.2.3-1-a5y17lte.img.tar, lineage-14.1-20181117-nightly-a5y17lte-signed.zip, and open_gapps-arm64-7.1-pico-20181204.zip.
With help from this discussion, the LineageOS wiki "Install LineageOS on a5y17lte", r/LineageOS "Heimdall Failed to send data" (a post by noahajac was very helpful. You'll find it soon after OP), and the Odin install guide.
Some problems I encountered was that heimdall isn't favoured for this, and that if you try to wipe your partition through TWRP and it says it couldn't mount /data, you need to format the partition before wiping it.
Edit: so upon using the phone for a bit, it became evident that the SIM card was not being detected. From what I've read so far, this is because the phone had Android Oreo and the LineageOS was for Nougat. So I will have to restore and then revert to a Nougat version of Android and try again from there...
Not gonna be finished tonight. As long as I can get the restore and cell service working...
Two Questions re: rooting the SM-A520W
1. How can I make a proper Nandroid Backup. Everytime I go into TWRP the /data partition is unavailable. Yes I formated it and flashed no-verity-opt-encrypt-6.0.zip but it still is Zero bytes.
2. After rooting, the Fingerprint scanner becomes non operational and the lock screen password/pin does not work (keeps asking for the same password/pin over and over even though they are correct.)
Thanks for the Help.
ethan_hines said:
1. How can I make a proper Nandroid Backup. Everytime I go into TWRP the /data partition is unavailable. Yes I formated it and flashed no-verity-opt-encrypt-6.0.zip but it still is Zero bytes.
2. After rooting, the Fingerprint scanner becomes non operational and the lock screen password/pin does not work (keeps asking for the same password/pin over and over even though they are correct.)
Thanks for the Help.
Click to expand...
Click to collapse
Which firmware are you running.
ashyx said:
Which firmware are you running.
Click to expand...
Click to collapse
I'm on Stock 8.0
I managed to fix problem 1 by flashing a modded Version of TWRP (3.2.3-TwrpBuilder) I am rooted with Magisk and now have access to the /data partition and can make a proper Nandroid Backup.
Problem 2 Is still there I seem to remember I have to replace Samsung Pass and Samsung Account, but I don't know where they are located I think I am supposed to create a directory in /prv-app I don't remember
I have that phone. I installed a custom recovery and used super SU.
SonicFan66 said:
I have that phone. I installed a custom recovery and used super SU.
Click to expand...
Click to collapse
I didn't want Super SU because it can't be hidden from apps that disable if root is detected esp. Snapchat
@ethan_hines did you figure it out? I am looking to do what you did.