hello All
i did something very very very bad
i was upon to downgrade my D855 from 5.0 to Kitkat but it stop on 17% in pc and 0% on the phone
it still like that for 40 min so i unplug USB and i restart the phone i just get message says (secure booting error) in the up left side of phone and after that black screen and LED (BLUE & RED) i can not get in to download mode but when i try i get this :
Qualcomm HS-USB QDLoader 9008 (COM41)
and when i try to enter to recovery mode i get had to do factory reset and same problem !
so anyone can help me with this ?
Thanks ..
any help plz
Hello.
Move your battery, then replace it.
Flash an official kdz from lg.com with LGflashTool and your phone will restart
Your device is Brick!!
Try to enter Download mode
Flash your device again with LG FLash tools(tot File) or KDZ
i found it holllllaaa
for everyone have this problem, on this link you can fix it
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
i used KIZ file by the way
and i wish frm supervisor to close this subject and write solved on it
thanks.
Hi guys,
I need your help. Yesterday i tried to install flash my stock firmware (S054) in my Lenovo VIBE K5 Plus A6020a46. Now it seems Bricked. I can't boot into fastboot mode and not into the recovery mode. When I tried to turn on nothing will happen its just show black screen. When I connect with pc its automatically connect on download mode and shows (Qualcomm HS-USB QLoader 9008 Com 3)Successfully installed but when i am tried to flash with "QFIL (Shows sahara error) or QcomDLoader (Shows Send Result and in progress and nothig will happend)" What should I do? Please help. :crying:
Try
Maybe this link can help you
forum.gsmdevelopers.com/showthread.php?t=26402
i am sorry but i have searched a lot but i couldn't unbrick my ZUK Z2, i flashed the Deodexed stock ROM and then the screen went all black with the LED glowing. If i press the power button i just see the ZUK logo and the screen goes black, i tried to boot it into fastboot but no luck. I somehow managed to get into the 9008 mode but while flashing with QFIL i get the sahara error saying unable to read header or something and with MiFlash i am getting "cannot read hello packet"
Any Help will be appreciated
EDIT:
The device has been fixed, i had to press the download button on the QFIL as soon as my phone boots into EDL mode.
did you flash through twrp? and if your bootloader if unlocked then you should have 5 sec bootloader placeholder from where u can reboot recovery . and if you are stuck into something different then it will be difficult to recover but possible. for sahara fail , play with settings in qfil like emmc, reset ,etc and try.And you can remove the port from device manager and retry if u r getting 9008 port.You should not get sahara fail. You will be get out of this easily just try things suggested. Your device is live as zuk logo is showing so dont worry.
And use latest qfil: http://www.androidbrick.com/download/download-latest-qualcomm-flasher-qfil-qpst-2-7-460/#
EDIT: Try this too-
Bootloader mode: shutdown state, press and hold the volume plus key + volume minus key, while the usb line connected to the computer until the release button.
Qualcomm QPST (9008 port) : shutdown state, press and hold the volume plus key, press the power button at the same time usb cable to connect the computer. This mode is a black screen state.
For recovery: press and hold the power key + the volume plus key + the volume down key until you release the release button.
Just buy DFC cable a.k.a Deep Flash Cable. The cable is same as you wire cable manualy
Kalp3sh S1NGH said:
i am sorry but i have searched a lot but i couldn't unbrick my ZUK Z2, i flashed the Deodexed stock ROM and then the screen went all black with the LED glowing. If i press the power button i just see the ZUK logo and the screen goes black, i tried to boot it into fastboot but no luck. I somehow managed to get into the 9008 mode but while flashing with QFIL i get the sahara error saying unable to read header or something and with MiFlash i am getting "cannot read hello packet"
Any Help will be appreciated
Click to expand...
Click to collapse
Onces that you are in 9008 mode you need to use ADB
"Adb reboot edl"
You are a lucky guy, i needed to conect grenn and black cable of the smartphone to put in 9008 mode
ozi87 said:
Onces that you are in 9008 mode you need to use ADB
"Adb reboot edl"
You are a lucky guy, i needed to conect grenn and black cable of the smartphone to put in 9008 mode
Click to expand...
Click to collapse
So i plug my phone in 9008 mode and go straight to adb?
Kalp3sh S1NGH said:
So i plug my phone in 9008 mode and go straight to adb?
Click to expand...
Click to collapse
Have you both any idea about adb! Edl is itself 9008 mode also called download mode. Adb is debug bridge and it is used in OS to control it by this bridge from PC.
pixel0 said:
Have you both any idea about adb! Edl is itself 9008 mode also called download mode. Adb is debug bridge and it is used in OS to control it by this bridge from PC.
Click to expand...
Click to collapse
yes exactly, that's why i asked.
pixel0 said:
did you flash through twrp? and if your bootloader if unlocked then you should have 5 sec bootloader placeholder from where u can reboot recovery . and if you are stuck into something different then it will be difficult to recover but possible. for sahara fail , play with settings in qfil like emmc, reset ,etc and try.And you can remove the port from device manager and retry if u r getting 9008 port.You should not get sahara fail. You will be get out of this easily just try things suggested. Your device is live as zuk logo is showing so dont worry.
And use latest qfil: http://www.androidbrick.com/download/download-latest-qualcomm-flasher-qfil-qpst-2-7-460/#
EDIT: Try this too-
Bootloader mode: shutdown state, press and hold the volume plus key + volume minus key, while the usb line connected to the computer until the release button.
Qualcomm QPST (9008 port) : shutdown state, press and hold the volume plus key, press the power button at the same time usb cable to connect the computer. This mode is a black screen state.
For recovery: press and hold the power key + the volume plus key + the volume down key until you release the release button.
Click to expand...
Click to collapse
I think the bootloader is locked again, i can't boot into recovery. I tried the latest QPST and still getting unable to read packet header read 0 bytes error and Sahara Failed.
Kalp3sh S1NGH said:
I think the bootloader is locked again, i can't boot into recovery. I tried the latest QPST and still getting unable to read packet header read 0 bytes error and Sahara Failed.
Click to expand...
Click to collapse
If bootloader is locked or unlocked , 9008 mode will work for sure. Also Use buttons combination to enter fastboot if u can then unlock and flash recovery from there .
To avoid this problem again, when you flash stock roms after using Custom Roms, make sure you format the System, data and cache partitions back to EXT4 format, since Stock firmware (even the moded ones) DOES NOT support any other System/Data/ Cache format.
After loading the bootloader, the phone will end with black screen and white led on. You just need to reboot on recovery again and advance format System/ Data/ Cache back to EXT4, connect the phone to the PC again, transfer the ROM file to the internal storage and make the Flash again...
Hope this help you
Hi
I just get my galaxy a5 from my bro, first thing it boot always in safe mode, I searched i found that my volume down is always stuck so it keep booting in safe mode.
I opened my phone, I tested the button with a tester, they work properly so I concluded that the problem is in the motherboard.
So I wanne to root my phone to get a tools to bypass that, I put the phone with ADB to download mode ( only way to do it) , with odin I have selected the root file TWRP_3.1.1-0_a5y17lte to the wrong case BL,
Now the phone stuck in bootloop and I can't flash it again with odin cause I no access to download mode.
I can go to download mode with Home+Power but can't continue with volume UP.
I need your help my probleme if there is a solution for me.
Thanks
I used USB JIG to force download mode but nothing happen ;(
Please some suggestion
Try to connect Smart swicth it will help you out.
Thanks
Smart switch don't help cause no download mode
Hey everyone
My LG G4 (H815) suddenly turned off when i was using it, and it showed no life when i tried to boot it up again. Its completely stock, no custom recovery or custom firmware is installed. I cant boot into fastboot or EDL mode. I tried the button combinations as well as the test point method but i just cant get it to enter any kind of recovery mode, the screen just remains black (no backlight either). I installed the Qualcomm HS-USB drivers and when i plug my phone in my pc it gets recognized by QFIL. I tried flashing the fimware but it always gives me the Sahara unable to read packet header error. Can anyone help me?
Thanks in advance.
Have you searched the forum and tried any of these ?
https://forum.xda-developers.com/t/guide-proper-h815-unbrick-through-qfil-files-included.3709212/
https://forum.xda-developers.com/t/...-unbrick-via-external-sdcard-no-qfil.3748946/
https://forum.xda-developers.com/t/lg-g4-h818p-h815-hard-brick-recovered-working.3703565/
https://forum.xda-developers.com/t/unbrick-lg-g4-9008-qualcomm-mbn-files.3574595/