Related
It has taken me many days to find a tool to flash KDZ AND TOT since many people show an error at 4% of FlashTool and there is no solution so this is your Post.
LGUP is a tool used by Lg for phones that still have a guarantee such as a system error or a software error.
Compatible with Windows vista/7/8/10 No macOS No Linux
Thanks to DroidTH for giving me a link
ok let's start
Renember: All will be erased in the internal memory.
Your warrantly is now avoid
Visit [How-to] Flash firmware KDZ G2 G3 G4 by LGUP On Youtube to the link
Remember that it is not channel advertising, it's just that I can not add external links
Steps to follow
Make sure you have the drivers installed correctly
Download The KDZ / TOT
Connect Lg g3 to pc (No need to enter download mode manually)
Unzip (LGUP-G2-G3.ZIP)
First install (LGUP_8974_DLL_Ver_0_5_CODEFIRE)
Second Install (LGUP_Install_Ver_1_14_3)
Enter the LGUP program that is probably hosted on your desktop
Select the Upgrade box and select the KDZ / TOT file
Wait for the process to finish (Do not disconnect the phone)
At 80% the phone will restart (not yet to be disconnected)
When you reach 100% the phone must have turned on or starting on the TMO logo
If it does not start
-------------------------------------------------- -------------------------------------------------- ----
If it does not start
---------------------------------------------- -------------------------------------------------- -----
If it restarts constantly and does not enter the system (It restarts before reaching the optimizing application)
Turn off the phone completely and remove the battery
Wait 10 seconds. And put it back
Press Vol- and on when logo is released and press them again.
Give you everything
EYE: all files on the internal SD card will be erased
A factory reset will be made and then it must be turned on normally.
If it still does not start, remove the chip (SIMCARD)
Well that's all if you have any questions please write
Sorry if I needed something, it's just that I'm new and I do not know anything about xda
I hope you understand.
When I run LGUP it says Model is Unknown, then gives an error telling me I have to choose a known Model. Drivers are installed, USB debugging is enabled, not sure what else there is missing. Please help.
my phone: (T-Mobile lg g3 d851 30e)
dricialg said:
error Unknown model.!!
my phone: (g3 d851 30e)
Click to expand...
Click to collapse
sorry you had problems
the error is one of the drivers lg
you should plug it into one of the main USB ports on your PC.
or rather entering device manager and re-assign drivers to ports.
Have you downloaded the lgup for lg g3 and g2?
Drivers are installed, USB debugging is enabled, LG PC Suite OK.not sure what else there is missing.
Download : lgup-g2-g3.zip
Solve it FIX
good after I found the problem LGUP
roms apparently change the model of the device as it changes cm11 to build Cyanogenmod 11 xx
AOSP - to AOSP rom 2 etc.
the solution would be to install a stock rom clean no matter if v10 v30 etc. The important thing is not having changed the model number and manufacturer.
I hope I have helped and sorry
that includes cloudy fa's roms
minicm94123 said:
It has taken me many days to find a tool to flash KDZ AND TOT since many people show an error at 4% of FlashTool and there is no solution so this is your Post.
LGUP is a tool used by Lg for phones that still have a guarantee such as a system error or a software error.
Compatible with Windows vista/7/8/10 No macOS No Linux
Thanks to DroidTH for giving me a link
ok let's start
Renember: All will be erased in the internal memory.
Your warrantly is now avoid
Visit [How-to] Flash firmware KDZ G2 G3 G4 by LGUP On Youtube to the link
Remember that it is not channel advertising, it's just that I can not add external links
Steps to follow
Make sure you have the drivers installed correctly
Download The KDZ / TOT
Connect Lg g3 to pc (No need to enter download mode manually)
Unzip (LGUP-G2-G3.ZIP)
First install (LGUP_8974_DLL_Ver_0_5_CODEFIRE)
Second Install (LGUP_Install_Ver_1_14_3)
Enter the LGUP program that is probably hosted on your desktop
Select the Upgrade box and select the KDZ / TOT file
Wait for the process to finish (Do not disconnect the phone)
At 80% the phone will restart (not yet to be disconnected)
When you reach 100% the phone must have turned on or starting on the TMO logo
If it does not start
-------------------------------------------------- -------------------------------------------------- ----
If it does not start
---------------------------------------------- -------------------------------------------------- -----
If it restarts constantly and does not enter the system (It restarts before reaching the optimizing application)
Turn off the phone completely and remove the battery
Wait 10 seconds. And put it back
Press Vol- and on when logo is released and press them again.
Give you everything
EYE: all files on the internal SD card will be erased
A factory reset will be made and then it must be turned on normally.
If it still does not start, remove the chip (SIMCARD)
Well that's all if you have any questions please write
Sorry if I needed something, it's just that I'm new and I do not know anything about xda
I hope you understand.
Click to expand...
Click to collapse
Where are downloads
minicm94123 said:
good after I found the problem LGUP
roms apparently change the model of the device as it changes cm11 to build Cyanogenmod 11 xx
AOSP - to AOSP rom 2 etc.
the solution would be to install a stock rom clean no matter if v10 v30 etc. The important thing is not having changed the model number and manufacturer.
I hope I have helped and sorry
Click to expand...
Click to collapse
Hi !
How do I do all the above ?
My PC recognize the phone without problem, but LGUp won't start unless I "select a known model"... (LGUp window shows : Model = Unknown ; COM Ports = [COM5, CloudyG3] )
Problem is that my phone is softbricked after installing a new ROM, and I can only enter download mode (not even recovery). I just want to downgrade it and reflash a LG's stock ROM (or whatever ROM that would make my phone actually work !!! )
Can you help me do that ?
raf1978 said:
Hi !
How do I do all the above ?
My PC recognize the phone without problem, but LGUp won't start unless I "select a known model"... (LGUp window shows : Model = Unknown ; COM Ports = [COM5, CloudyG3] )
Problem is that my phone is softbricked after installing a new ROM, and I can only enter download mode (not even recovery). I just want to downgrade it and reflash a LG's stock ROM (or whatever ROM that would make my phone actually work !!! )
Can you help me do that ?
Click to expand...
Click to collapse
Do you still wanting help?
minicm94123 said:
Do you still wanting help?
Click to expand...
Click to collapse
YEEEESSSSSS !!!!
Please.... ?
(My phone is currently used as a toy by my 6 yo daughter ? )
LGUP "UNKNOWN" and FlashTool failure with LG G3 (and possibly others)
When I downloaded and installed LGUP with the DLL installer stated to be for the LG G3, the program did not recognise the phone, reporting it as "UNKNOWN". The LG FlashTool also failed, reporting the IMEI and PID as NULL. After spending a lot of time on this, I twigged that the DLL file in the LGUP model directory was for the 8994 processor; but the G3 has an 8974, quite different and incompatible. I located the DLL installer MSI file for 9874 devices, uninstalled LGUP and the DLLs from Windows add/remove programs, ran the 9874 DLL installer and reinstalled the LGUP program, and everything worked.
The file is, amongst other places, on https://uptoandroid.com/download-lg-up-tool-for-lg-smartphone-latest/. Do not download DLL files for LG G4, LG V10, LG G3, LG Stylo, filename LGUP_Common_DLL_Ver_1_0_28_5 .msi, but instead For LG phones based on Qualcomm Snapdragon 800 MSM8974 SoC, filename LGUP_8974_DLL_Ver_0_5.msi:.
HTH
23 Aug 19: I find that I've rediscovered the wheel. Exactly what I said was posted in 2016 - if I'd found it, it would have saved me a lot of time!
Hi, I decided to write here, I hope you can help me out.
So today I tried to root my phone with the instructions found at https://forum.xda-developers.com/showpost.php?p=68696079&postcount=114
I checked that my build no. is S288, so with rooting there would be no data loss for me (I still backed up everything important of course)
First problem I came across was that I had to found how to download QFIL, I downloaded and installed version 1.0.0.2 I think.
Second was that I couldn't get the Qualcomm Com port to show in QFIL neither in Device Manager. I figured out that as well, by doing loads of research (googling)
I also installed ADB to help me get into the state where I see the Qualcomm port, because normally if I just power it off, and connect it to my PC, it powers on in the "charging interface"
So everything was working, I downloaded the P1a42_S288_160721_ROW_RAW_QFIL file, extracted it, filled in everything in the QFIL program and hit Download while holding the + & - buttons to enter TWRP mode or whatever it is called. It returned with this:
Code:
PROGRAM: Send raw data fail
Failed to write I:\Telefon Ment�sek\Lenovo Vibe P1\Root (2017,03,11)\P1a42_S288_160721_ROW_RAW_QFIL\recovery_twrp.img to the device
Download Fail:System.Exception: Failed to upload the emmc images to the phone using Firehose
...
Download Fail: FireHose Fail FireHose Fail
Finish Download
Sorry, I can't write down everything bc I already closed the program, so I'm writing these off of screenshots
I already tried other USB cables, other USB ports, other drivers, even other ROMS, but everytime I try, I get this message:
Code:
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
So currently I can't power on the device in any way, tried holding + and -, + and power, - and power, home and power, home power and +, home power and -, home power + -
Please help me, I would be really glad Cheers!
Also, sorry if my English is a bit poor, I'm a 15 year old boy who's native speaking lang is not English
P.S. I also don't know if I broke my warranty with this or not, because I technically have not rooted the phone, just did something else. And also, what if someone would've stolen it and I would've got it back and I wouldn't be able to turn it on because the thieves have broken it? (That is not the case right now, just asking).
PS 2: I have an alarm at 0:00 today, but I doubt that the phone is just gonna magically turn itself on for the alarm, we'll see. I may also try to leave the phone to completely discharge (I remember now why I didn't want to buy a phone with a built-in battery)
EDIT: I didn't mention, that the first time I tried to flash, I was using files from a Directory that's path contains both spaces and unknown (?) characters (é) (only unknown by the software) as seen above in the first box.
gabor6505 said:
Hi, I decided to write here, I hope you can help me out.
So today I tried to root my phone with the instructions found at https://forum.xda-developers.com/showpost.php?p=68696079&postcount=114
I checked that my build no. is S288, so with rooting there would be no data loss for me (I still backed up everything important of course)
First problem I came across was that I had to found how to download QFIL, I downloaded and installed version 1.0.0.2 I think.
Second was that I couldn't get the Qualcomm Com port to show in QFIL neither in Device Manager. I figured out that as well, by doing loads of research (googling)
I also installed ADB to help me get into the state where I see the Qualcomm port, because normally if I just power it off, and connect it to my PC, it powers on in the "charging interface"
So everything was working, I downloaded the P1a42_S288_160721_ROW_RAW_QFIL file, extracted it, filled in everything in the QFIL program and hit Download while holding the + & - buttons to enter TWRP mode or whatever it is called. It returned with this:
Code:
PROGRAM: Send raw data fail
Failed to write I:\Telefon Ment�sek\Lenovo Vibe P1\Root (2017,03,11)\P1a42_S288_160721_ROW_RAW_QFIL\recovery_twrp.img to the device
Download Fail:System.Exception: Failed to upload the emmc images to the phone using Firehose
...
Download Fail: FireHose Fail FireHose Fail
Finish Download
Sorry, I can't write down everything bc I already closed the program, so I'm writing these off of screenshots
I already tried other USB cables, other USB ports, other drivers, even other ROMS, but everytime I try, I get this message:
Code:
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
So currently I can't power on the device in any way, tried holding + and -, + and power, - and power, home and power, home power and +, home power and -, home power + -
Please help me, I would be really glad Cheers!
Also, sorry if my English is a bit poor, I'm a 15 year old boy who's native speaking lang is not English
P.S. I also don't know if I broke my warranty with this or not, because I technically have not rooted the phone, just did something else. And also, what if someone would've stolen it and I would've got it back and I wouldn't be able to turn it on because the thieves have broken it? (That is not the case right now, just asking).
PS 2: I have an alarm at 0:00 today, but I doubt that the phone is just gonna magically turn itself on for the alarm, we'll see. I may also try to leave the phone to completely discharge (I remember now why I didn't want to buy a phone with a built-in battery)
EDIT: I didn't mention, that the first time I tried to flash, I was using files from a Directory that's path contains both spaces and unknown (?) characters (é) (only unknown by the software) as seen above in the first box.
Click to expand...
Click to collapse
Dear Pls follow this link
https://forum.xda-developers.com/vibe-p1/how-to/lenovo-vibe-p1-a42-c72-root-ready-t3533693
You can see the qualcomm driver only when you switch off phone and hold Volume+/- plus power button.
I can't bc my phone won't turn on currently,
So I probably shouldn't have used ADB to get into fastboot or whatever, my phone may be broken because I tried to do the flash while in that state.
Did you read my whole post though?
The next thing I'll try then is uninstalling all the drivers and programs related to my phone, and then following the guide you suggested, because I still see the Qualcomm port, I just can't do anything with my phone.
OMG, I have waited a few hours, and just randomly thought why not try again flashing the rom (I don't think this is the right word for the QFIL Download procedure), and it worked! So I'm actually really happy I don't need to send it in to repair or try other things. I got the system I started the procedure with, so I didn't actually lost any of my files neither did I root my phone. Now to decide if I want to try again rooting it with the detailed instructions you sent or just leave it like this so I avoid getting into all this again. I think I will try again to root it lol why not
Will report back here if it was successful
I have successfully rooted my phone, and installed the Xposed Framework on my phone, so I'm really happy.
I can't really seem to find where to lock this thread so please someone lock this thread (I am not familiar with this forum, so I don't know if it is needed or not)
i have a old mediacom tabled... a smartpad i10 3g (link to product at mediacom -> http://www.mediacomeurope.it/tablet/scheda.aspx?XRI=30) and i have tryed to restore to factory instead so many little troubles.
I have download the FactoryTool.... i have installed the Flash driver and i have download the firmware for my serial............ i have extracted it and i try to flash following the pdf instruction.
I have turned off my tablet.... clicked run and connected the tablet to usb pc port.......... i can see a usb driver has correctly loaded (Intel USB Flash Loader Utility) but on FactoryTool i see so many problems immediatelly.
So many times i see an errors says: Syncronizing device failed.
I have tryed so many times (also ever restart my pc) and some time i see an errors says somethigs similar "failed to download boot.fls"
Now what's the problems.............. the tablet it's apparently dead! i can press the power buttons also for 20 seconds and never append... the screens goes ever black and never appends.......
How i can do now ? It's time to trash this tablet ?
DjDiabolik said:
i have a old mediacom tabled... a smartpad i10 3g (link to product at mediacom -> http://www.mediacomeurope.it/tablet/scheda.aspx?XRI=30) and i have tryed to restore to factory instead so many little troubles...
Click to expand...
Click to collapse
Your best bet is to post this question within the following thread that looks like it's the same device as yours.
http://forum.xda-developers.com/showthread.php?t=2408507
Good Luck!
~~~~~~~~~~~~~~~
I DO NOT PROVIDE SUPPORT VIA PM UNLESS ASKED/REQUESTED BY MYSELF.
PLEASE KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
OH.. ok...
Otherwise i found the solution later the same night........... i thinks it's a BUG on Flashtools 1.28......
When i extract the mediacom firmware downloaded from site i use a folder on D:\ . The zip files of roms contain a special caracter inside and the folder.
When i load all firmware files inside flashtools apparently all it's be loaded correctly but during the flash operation i obtain ALL FILE CAN'T BE FOUNDED!!!
Yeah... all files it's not be found because the app can't reach the files in this "special" folders!!! I have notified it only after hours and hours and i have read it inside a log files (ah.. all files log it's not a text files...... very strange).
After i have read the log files i copy all files extracted inside a folder D:\AAA......... i reload all files on flashtools and BAAM!! The flash opertion it's completed whitout any problems!!!
DAMN!! it's only this the problems.... the flashtools app can't reach the files if it's inside a strange name folder!! DAMN again
Now the tablet it's back to live again......... but apparently some of little trouble it's remain like the continuesly disconnession from my wi-fi............. i don't have idea what's it's the problems.......
Can you explain with more details please, I have the same problem with a tablet : Mediacom Smartpad i10
Is there any video explaining the solution ?
Hello Guys
My friend ask me for get a Lineage OS to his H815 with Nougat. I agreed as I made few successful changes from stock to Lineage OS with Samsungs and older LGs (like L3 E400). But G4 is really more complicated, more than I expected . Firstly I wanted to unlock this phone with FWUL, so I download a VirtualBox emulated image with FWUL and after it boots I opened SALT program and it detects the phone. I made a basic backup and then I choosed Unlock G4 (UsU). After that some windows pop up. Last window was a pre-checking, when the bar gets to the end window closed and nothing more was happening. So after almost hour of waiting I just turned off the phone - I thought its all. After that while phone is booting I have those messages in the left top corner:
[820]-----------------------
[870]
[920] Secure boot error!
[970] Error code : 1009
[1020[ OFFICIAL !!
[1070]
[1120]-----------------------
Its booting, but only sometimes its normal boot, most starts are with bootloop, sometimes its start after 10 restarts, sometimes after 2nd restart, sometimes after plug in/plug out USB cable it starts boot normally (connecting cable only to phone, not to PC), sometimes only thing that helps is to take out the battery. I made full wipe to be sure that its not a software problem, but only thing I achived with that is fact that phone has a Nougat and now it have a Marshmallow. It is (was?) H815, but now model name is LGLS991 (?), it gets very long until it shows software version (V20g), IMEI is unknow, even when I type *#06# I get the null response.
I can get into recovery, can put phone into download mode. But i'm not able to do anything to get LOS or a least Nougat.
I've read many, many tutorials how to get G4 working properly after unsuccessful unlock, but nothing helps. What I've tried:
1. Flashing stock Nougat for H815 with LGUP, installed USB drivers, proper DLL, set com to 41, but when I trying to flash, after a 4% i get error: KDZ file is invalid. Downloaded few KDZ firmwares, dont belive that every single one is invalid, there is something wrong with LGUP or with settings, but I cant find what
2. Flashing with LG Flash Tool 2014: tried both normal flash and cse flash and always stoping in the same moment, with "Connection to server failed. Try again in a moment". Read many tutorials about this error, none was helpful in my case.
3. Flashing with LG Flash Tool v1.8.1.1023 and a TOT file, but after select of dll and tot file and press the yellow arrow I get an error: "Failed PreviousLoad()"
Tried all this methods on second computer but without a luck.
What else can I try to get this G4 working properly? Maybe try to install some rom from stock recovery? But which rom will be ok and dont get things worst?
If you need more info dont hesitate to ask. Would be very greatful for any advices .
you definitely didn't read enough... go to read again the UsU thread and as you've read the whole tutorial, you can also read the whole FAQ and the OP, because 90% of what you pointed out in your publication (which incidentally is in the wrong section) is explained there.
A quick advice: Don't try to flash any KDZ/TOT again.
Hi folks,
Back again after a long absence...
I'm in UK, just bought this phone (from China)... looked good, even though old now and seems good so far.
But, some apps that I want to use won't run on 5.1... some that I would really like to have will run on 6, others may need 7
LG Bridge identifies the phone, recognises that there's a software update available, downloads it and starts the software install but the update gets to 9% then fails, with message "Phone cannot update"
I've enabled Developer options and USB debugging
Build number is LMY47D, Software version = H81510h, Security Software version = MDF V1.1 Release 5
Checking for 'Software Updates' through 'Update Center' on the phone returns the message "Your device is up to date"
From reading several threads here, it looks like there may be a couple of possibilities: the laptop I'm running LG Bridge on only has USB 3.0 ports - one of the threads said somewhere "USB 3.0 will not work". Is that true? Anyway, I'll try LG Bridge on another laptop with USB 2.0
If that doesn't work, I guess I have to use LGUP which will wipe all the data on the phone (so I'll backup first) - I think I can do this without having to root; I'll check whether I have to go through the OEM unlock process described here
That thread is from 2016, though, so if any of that is now out of date, I'd be grateful for any advice, links to most up to date info, etc.
I'd like to get to Android 6 with mimimal hassle / risk / wiping of data, then see if I really need 7
Many thanks, in anticipation,
Ian
IanCDx said:
Hi folks,
Back again after a long absence...
I'm in UK, just bought this phone (from China)... looked good, even though old now and seems good so far.
But, some apps that I want to use won't run on 5.1... some that I would really like to have will run on 6, others may need 7
LG Bridge identifies the phone, recognises that there's a software update available, downloads it and starts the software install but the update gets to 9% then fails, with message "Phone cannot update"
I've enabled Developer options and USB debugging
Build number is LMY47D, Software version = H81510h, Security Software version = MDF V1.1 Release 5
Checking for 'Software Updates' through 'Update Center' on the phone returns the message "Your device is up to date"
From reading several threads here, it looks like there may be a couple of possibilities: the laptop I'm running LG Bridge on only has USB 3.0 ports - one of the threads said somewhere "USB 3.0 will not work". Is that true? Anyway, I'll try LG Bridge on another laptop with USB 2.0
If that doesn't work, I guess I have to use LGUP which will wipe all the data on the phone (so I'll backup first) - I think I can do this without having to root; I'll check whether I have to go through the OEM unlock process described here
That thread is from 2016, though, so if any of that is now out of date, I'd be grateful for any advice, links to most up to date info, etc.
I'd like to get to Android 6 with mimimal hassle / risk / wiping of data, then see if I really need 7
Many thanks, in anticipation,
Ian
Click to expand...
Click to collapse
Hmmm... other laptop is all USB 3.0 too
A bit more info from LG Bridge, which failed again:
-----------------------------------------
There is an update available
Model: H815
New version: H81520P (06.28.2018)
1.65GB
-----------------------------------------
Phone reboots to Download mode - shows Firmware Update screen, which sticks at 0%
LG Bridge:
- downloads the software update
- update fails again with 9% on LG Bridge update progress screen
- reports "Your phone cannot update"
- suggests: disconnect USB, remove battery from phone, reconnect, retry
- doesn't work
- LG Bridge won't close, reports 'software is busy'
- process has to be killed in Task Manager
Download LGup. Download the h815 20p KDZ and flash it by lgup.
You could download 20p from here for example:
https://leech.binbash.rocks:8008/stock/LG/h815/20p/
--> h815_20p_ARB0_0314.kdz
Thanks steadfaster
Still a bit stuck though...
I've tried a couple (I think... maybe more..?!) different versions of LGUP I found...
Definitely LGUP_Store_Frame_Ver_1_14_3.msi, and LGUP_Dev_Frame_Ver_1_15_0_6.msi
That last one didn't work as it required registration and login
Phone was recognised first time in store version 1.14 and upgrade process started:
---------------------------------------
LGUP[H815] store version : 1.14
Upgrade selected
File Type
Bin File
h815_20p_ARBO_0314.kdz
-------------------------------------------------------------------
Stopped with Error:
Error Code = 0x2000,
TOT antirollback version is smaller than the device version
I've been reading various threads for several hours today, and trying various suggested solutions, including:
- adding a 'common' folder to LGUP in Program Files (x86) and copying LGUP_Common.dll there
- downloading something called Uppercut.exe which Norton prevented from running, identifying it as malware..??
- changing properties of the Port the phone is connected to
None of which have worked; I got the 0x2000 error on one attempt.
LGUP now doesn't see the phone 'properly'... comes up as 'Unknown model' and 'says' I have to connect a known model before it will do anything...
So, a few things to check:
Do I run LGUP in windows? (I think I read somewhere it's specifically designed to run on Windows)
Which version of LGUP should I install and use? [A known good link would be really helpful ;-)]
Do I connect the phone (USB / MTP) while it's running normally, or boot it into download mode first? Took me a while to even get there... and that also didn't work...
Many thanks for your time and expertise
IanCDx said:
Thanks steadfaster
Still a bit stuck though...
I've tried a couple (I think... maybe more..?!) different versions of LGUP I found...
Definitely LGUP_Store_Frame_Ver_1_14_3.msi, and LGUP_Dev_Frame_Ver_1_15_0_6.msi
That last one didn't work as it required registration and login
Phone was recognised first time in store version 1.14 and upgrade process started:
---------------------------------------
LGUP[H815] store version : 1.14
Upgrade selected
File Type
Bin File
h815_20p_ARBO_0314.kdz
-------------------------------------------------------------------
Stopped with Error:
Error Code = 0x2000,
TOT antirollback version is smaller than the device version
I've been reading various threads for several hours today, and trying various suggested solutions, including:
- adding a 'common' folder to LGUP in Program Files (x86) and copying LGUP_Common.dll there
- downloading something called Uppercut.exe which Norton prevented from running, identifying it as malware..??
- changing properties of the Port the phone is connected to
None of which have worked; I got the 0x2000 error on one attempt.
LGUP now doesn't see the phone 'properly'... comes up as 'Unknown model' and 'says' I have to connect a known model before it will do anything...
So, a few things to check:
Do I run LGUP in windows? (I think I read somewhere it's specifically designed to run on Windows)
Which version of LGUP should I install and use? [A known good link would be really helpful ;-)]
Do I connect the phone (USB / MTP) while it's running normally, or boot it into download mode first? Took me a while to even get there... and that also didn't work...
Many thanks for your time and expertise
Click to expand...
Click to collapse
Yes the dll is needed to make lgup work. There are various threads here including proper instructions (iirc)
I've read several more threads here - after searching for everything on LGUP - and taken a few steps trying to get this to work... no joy so far:
- restored Windows 10 to state before I originally installed LGUP... to be certain I do it as described here, installing LGUP_8994_DLL_Ver_0_0_3_23 first then LGUP 1_14_3.msi
- downloaded and ran uppercut.exe with LGUP (I had to disable Norton autoprotect to do this as it (mistakenly..?) identifies uppercut.exe as a heuristic virus
Doing this means LGUP sees the G4 H815 correctly: it was seeing it as an unknown device before I took these steps
Ticked Refurbish in LGUP, but couldn't select the .kdz file... Refurbish was looking for a 'Tot' file
With the phone still connected (MTP and USB debugging enabled)
- selected 'Upgrade' in LGUP
- loaded the file 'h815_20p_ARB0_0314.kdz'
- failed at 9%, with 0x2000 error
Here's the screenshot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Seems I might've run out of options here... wondering if I need to go down unlocking route... maybe try FWUL --> SALT --> next steps..?
I need to go back to your original SALT thread, steadfaster, to remind myself of the steps, but can I still install stock ROM (h815_20p_ARB0_0314.kdz) if I go this way..?
Or do I have to go with a custom ROM after unlocking..?
So I'm looking at using SALT in mAid (and maybe I'm being a bit dumb here, but I think it's just ignorance in its true sense) but I cannot suss out how to get mAid installed onto a USB flash drive... nor can I see a version 4 of mAid, which would be called mAid rather than FWUL, so I'm not clear which version / which file I should be using anyway..?!
Just used Rufus to burn FWUL_v3.1_x86_64_persistent.img onto 16Gb USB drive... let's see...
--> installed that FWUL_v3.1 onto USB
--> booted successfully..! (no surprise to you, I imagine, but I was v. pleased to see linux running on this laptop )
--> started SALT, connected phone in DL / firmware update mode: saw phone, lots of details, incl. ARB version = 2
--> KDZ button: message comes up something like: "To flash firmware use KDZ + Flash option" but I can't see or find that, so I stop for tonight (getting late), plus I can't access my internal drives through FWUL, it's asking for authentication and I don't know what's required...
--> copied the .kdz file (h815_20p_ARB0_0314.kdz) onto the USB
-------------------------------------------------------------------------------
=> Try again tomorrow
IanCDx said:
--> installed that FWUL_v3.1 onto USB
--> booted successfully..! (no surprise to you, I imagine, but I was v. pleased to see linux running on this laptop )
--> started SALT, connected phone in DL / firmware update mode: saw phone, lots of details, incl. ARB version = 2
--> KDZ button: message comes up something like: "To flash firmware use KDZ + Flash option" but I can't see or find that, so I stop for tonight (getting late), plus I can't access my internal drives through FWUL, it's asking for authentication and I don't know what's required...
--> copied the .kdz file (h815_20p_ARB0_0314.kdz) onto the USB
-------------------------------------------------------------------------------
=> Try again tomorrow
Click to expand...
Click to collapse
FWUL 3.2(!) is the latest supported FWUL version. 3.1 has issues especially with SALT which cannot be updated on FWUL 3.1. So either use FWUL 3.2 or mAid 4.0 which can be found beyond the nightlies link in the OP.
The FWUL thread explains how to flash FWUL / mAid: install and start balena etcher.
If rufus worked then good use it - just keep in mind it is not tested nor supported.
Also consider joining one of the support chats which you can find in the FWUL thread (Telegram or Matrix)
Got myself into a bit of a muddle but I've worked through and sussed a couple of things out...
(First lesson: it really does pay to read more..!)
I hadn't understood the difference between persistent and forgetful - obviously hadn't read enough of your FWUL thread, i.e. the FAQ in post #4 - so couldn't work out why it looked like balenaEtcher was trashing my flash drives, making the free space unusable..! Sorted now, and have FWUL3.2 forgetful.
In any case, I've booted from USB versions of both mAid and FWUL 3.2 today
=> I haven't managed to work out how to access unencrypted data partitions on a HDD on the laptop I'm using (Windows is on NVMe SSD)
=> I copied the h815_20p_ARB0_0314.kdz file onto the USB drive that I'm booting FWUL 3.2 forgetful from, but couldn't see it in FWUL file manager...
=> SALT connects and gives the detailed info re the phone that may explain why I haven't been able to flash firmware update with LG Bridge or LGUP
=> I still don't see an Extract + Flash option in SALT - should I..?
SALT gives these details re the phone:
Device model = LG-810
Firware (laf) = H81010o
Firmware (system) = LGH815AT-00-V10h-GLOBAL-US-AUG-17-2015-ARB02+0
Carrier: ATT
Country: US
UsU: no
GPT compatibility: H811
LAF protocol: 1000001
Battery level: 100
AntiRollBack: 20 (not sure if that was 2.0..?)
(plus IMEI and Serial)
- Does the fact it's actually an H810, with ARB 2 explain why I haven't been able to update firmware..?
- Do I have to unlock now to be able to update..?
- Or try different firmware..?
Many thanks for your help with this...
IanCDx said:
Got myself into a bit of a muddle but I've worked through and sussed a couple of things out...
(First lesson: it really does pay to read more..!)
I hadn't understood the difference between persistent and forgetful - obviously hadn't read enough of your FWUL thread, i.e. the FAQ in post #4 - so couldn't work out why it looked like balenaEtcher was trashing my flash drives, making the free space unusable..! Sorted now, and have FWUL3.2 forgetful.
In any case, I've booted from USB versions of both mAid and FWUL 3.2 today
=> I haven't managed to work out how to access unencrypted data partitions on a HDD on the laptop I'm using (Windows is on NVMe SSD)
=> I copied the h815_20p_ARB0_0314.kdz file onto the USB drive that I'm booting FWUL 3.2 forgetful from, but couldn't see it in FWUL file manager...
=> SALT connects and gives the detailed info re the phone that may explain why I haven't been able to flash firmware update with LG Bridge or LGUP
=> I still don't see an Extract + Flash option in SALT - should I..?
SALT gives these details re the phone:
Device model = LG-810
Firware (laf) = H81010o
Firmware (system) = LGH815AT-00-V10h-GLOBAL-US-AUG-17-2015-ARB02+0
Carrier: ATT
Country: US
UsU: no
GPT compatibility: H811
LAF protocol: 1000001
Battery level: 100
AntiRollBack: 20 (not sure if that was 2.0..?)
(plus IMEI and Serial)
- Does the fact it's actually an H810, with ARB 2 explain why I haven't been able to update firmware..?
- Do I have to unlock now to be able to update..?
- Or try different firmware..?
Many thanks for your help with this...
Click to expand...
Click to collapse
> => I haven't managed to work out how to access unencrypted data partitions on a HDD on the laptop I'm using (Windows is on NVMe SSD)
open the file explorer and you should see your windows disk in the left panel. click on it and it should mount (asking for the FWUL/mAid login password which is always: "linux")
> => I copied the h815_20p_ARB0_0314.kdz file onto the USB drive that I'm booting FWUL 3.2 forgetful from, but couldn't see it in FWUL file manager...
the USB stick is fully managed by the OS and so you cannot use it to copy data etc. use another stick or usb hdd disk or access your windows drives (see above)
> => I still don't see an Extract + Flash option in SALT - should I..?
yes and no. The "Extract" button for KDZs is there always. Flashing not. SALT is not meant to be used by the average user to flash. there is a way when needed but as it is dangerous it is not enabled by default
> SALT gives these details re the phone:
> Device model = LG-810
> Firware (laf) = H81010o
yea congrats! you have won.. this is a so called "Frankenstein" device! Pls take the time to read UsU FAQ #21. when SALT shows h810 like it does it is at 95% a H810. to be 100% follow that FAQ but usually it is as it is shown.
this is bad in many ways: no one actually can say what the guy did with your phone, for sure flashing another bootloader stack to make it boot etc. but what else? nobody then that human knows. this can have a lot of site effects later!
> LAF protocol: 1000001
that means you could use SALT for flashing if ever needed. if you flash MM for example this will increase to a higher number where SALT cannot flash anymore
> AntiRollBack: 20 (not sure if that was 2.0..?)
you have to switch to "develop" in SALT (thought I had said that?!). Read the SALT faq how to do that. After that the ARB should show up correctly (in your case just "2").
this ARB + model and LAF firmware all together results in 100% that this device is NOT a h815. if its really a h810 stays at "only" 95% though
> - Does the fact it's actually an H810, with ARB 2 explain why I haven't been able to update firmware..?
yes
> - Do I have to unlock now to be able to update..?
the h810 (assuming it is one) is not able to unlock officially. the only avail method is by UsU. If you want to go with a custom ROM then its your only option. If you want to stay stock.. well hard to say. as said above anything you do normally to a G4 might not work or break things in a Frankenstein.
For example you could try flashing a H810 MM ROM and see if LGup let you do that or not. again that might make things worse and now that it is clear that your ARB is blown (never the case for a h815) you have to ensure that you do not flash any ROM with a higher ARB then 2. Otherwise you will not be able to unlock by UsU if you ever want to do so.
as you can see there are no clear instructions how to proceed. all depends on your own risk level and what you actually can live with. assuming the device is a h810 you could unlock with the h810 UsU files and then work with that device as it would be a h810 (i.e. flashing h810 ROMs). Will you have any issues that way? No idea.. its a Frankenstein
in any case I would recommend before doing ANYTHING ELSE - regardless of what (UsU or not, other stock ROM versions etc) - DO A SALT BACKUP! Start SALT -> Backup -> Basic. This contains all required files needed for restoring essential parts of the system (e.g. bootloader, modem etc) but not the Android ROM itself. If you wanna backup that too choose "custom" and select everything except "userdata" and "cache". that one will take way longer obviously and you need enough disk space ofc. again it is good having access to your windows drive or if that does not work another USB stick/disk.
Last but not least: SALT -> Advanced menu -> Debug log -> UPLOAD button: this is the most easiest way to share the SALT log which is a good idea usually.
Excellent..!
Thanks a lot for all your help with this...
I might just put up with it as is for now, since the reason I got this was as a cheap replacement for a Xiaomi A2 lite which the touch screen stopped working on - so I've recently spent two weeks with no phone which wasn't a disaster, but inconvenient... maybe wait until I get that Mi repaired then decide whether I want to try one of those possible routes.
Thanks again... I bought you a drink..! (donated on your server)