My sister's S4 mini suddenly died, I cannot open the smartphone nor go on Recovery or download mode.
I used a debrick.img found here on xda put on a externaSD and manage to enter the download mode, then i try to flash a stock rom but it got stuck during the process (i leave odin running for hours without any success).
After that, when i retry the process this is what i got on screen:
Code:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS. .
COPY FROM T-FLASH. .
WRITE 139008 sectors. .
FLASH WRITE FAILURE
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: GT-I9195
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
BOOTLOADER AP SWREV: 2
CSB-CONFIG-SLB: 0x30
WRITE PROTECTION: ENABLE
I try to flash different .pit file found here on xda for the i9195 but if i try to flash (using Odin 3.13 or even odin 1.85) it says
Re-Partition operation failed or There is no PIT partition.
Any other idea i can try?
Maybe another .pit file for i9195 and a firmware that work with it?
Thanks to everyone
Goku_ssj3 said:
My sister's S4 mini suddenly died, I cannot open the smartphone nor go on Recovery or download mode.
I used a debrick.img found here on xda put on a externaSD and manage to enter the download mode, then i try to flash a stock rom but it got stuck during the process (i leave odin running for hours without any success).
After that, when i retry the process this is what i got on screen:
I try to flash different .pit file found here on xda for the i9195 but if i try to flash (using Odin 3.13 or even odin 1.85) it says
Re-Partition operation failed or There is no PIT partition.
Any other idea i can try?
Maybe another .pit file for i9195 and a firmware that work with it?
Thanks to everyone
Click to expand...
Click to collapse
I think her EMMc chip is probably dead, so needs replacing (new motherboard)
Related
Hi,
I'm a newbie to this, but i tired following a few recommended stuff off this thread and
still nothing please help.
Got a sph-l710 that wont turn on,
i tried a few debricking images one got it to vibrate with this on screen
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS..
COPY FROM T-FLASH..
BOOT RECOVERY..
WRITE 159488 sectors..
FLASH WRITE FAILURE
ODIN MODE
PRODUCT NAME: SPH-L710
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit:0
BOOTLOADER AP SWAEV: 2
then when i run it through odin
it reads ODIN: flash read failure in red
Please help
I've been reading many threads over the last 3 days, and I can't get back my SM-N9005.
My N9005 (Portuguese TPH) bricked doing a firmware update from 4.4.2 N9005XXUGNG1 (Portuguese TPH) to 5.0 Lollipop N9005XXUGBOB6 (Poland XEO) with Odin 3.09. Odin said success (PASS), but phone never rebooted.
Solution #1: http://forum.xda-developers.com/showthread.php?t=2531224 Thanks @msmercy42 I learned a lot from it but none of the N9005 unbrick.img worked for me.
Solution #2: http://forum.xda-developers.com/showthread.php?t=2625332 Thanks @ValenteL finally my N9005 goes into ODIN/Download mode.
However, I belive that solution #2 isn't going as smooth as it should. This is what I get when I get the phone to start from SD card:
Code:
[COLOR="Lime"]BOOT RECOVERY MODE[/COLOR]
CHECK BOOT PARTITIONS. .
COPY FROM T-FLASH. .
BOOT RECOVERY. .
WRITE 163840 sectors. .
[COLOR="Red"]FLASH WRITE FAILURE[/COLOR]
ddi : mmc_read failed
[COLOR="red"]ODIN MODE[/COLOR]
PRODUCT NAME: SM-N9005
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
[COLOR="Gray"]QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S2, T2, R2, A3, P2
WRITE PROTECTION: Enable[/COLOR]
[COLOR="Red"]UDC START[/COLOR]
And then, Odin recognizes the phone.
Now I'm able to get Odin to recognize the phone, but I can't do anything with it. I've tried:
- flashing 4.4.2 N9005XXUGNG1 (Portuguese TPH) again - FAIL (see attachments) Phone outputs two lines, after UDC START:
Code:
[COLOR="Gray"](...)
WRITE PROTECTION: Enable[/COLOR]
[COLOR="Red"]UDC START[/COLOR]
MMC: mmc_read fail
[COLOR="Red"]ODIN : flash read failure[/COLOR]
- flashing N9005XXUGBOB6 (Poland XEO) again - FAIL
- flashing PIT files (tried 3 different ones) - FAIL Phone outputs another line, after UDC START:
Code:
[COLOR="Gray"](...)
WRITE PROTECTION: Enable[/COLOR]
[COLOR="Red"]UDC START[/COLOR]
MMC: mmc_read fail
I wasn't able to get any unbrick.img from a N9005 Lollipop yet. Is this the final solution for my problem? Since I'm able to get to odin mode, shouldn't this unbrick be enough? What does it mean "mmc_read fail"?? Any help?!?! I don't know what else to do...
Thanks!!
sorry, wrong location... already started a new thread on 9005 Galaxy Note 3 proper location.
http://forum.xda-developers.com/galaxy-note-3/help/help-sm-n9005-hard-bricked-sd-partial-t3070743
Moderator: please delete this one, i'm sorry for the inconvenient.
hello guy's, my samsung today work's fine and from one hour not work at all - dead, i try to turn on no lucky, enter recovery no lucky, enter download mode not lucky
i found on forum about debrick.img and put on 16GB card, and phone vibrate and turn on but stuck like on the pictures mmc read failed, any sugestion, all the best
http://postimg.org/image/ar0zp4olp/
http://postimg.org/image/h3g4yyrnx/
gigidel said:
hello guy's, my samsung today work's fine and from one hour not work at all - dead, i try to turn on no lucky, enter recovery no lucky, enter download mode not lucky
i found on forum about debrick.img and put on 16GB card, and phone vibrate and turn on but stuck like on the pictures mmc read failed, any sugestion, all the best
http://postimg.org/image/ar0zp4olp/
http://postimg.org/image/h3g4yyrnx/
Click to expand...
Click to collapse
Sounds like the emmc memory is dead. Try to use these debrick images that I had taken from my i9195 some time ago. Extract first. https://drive.google.com/file/d/0B_vlSjY0nNrkX001ZUs4ZUF6dXc/view?usp=sharing
https://drive.google.com/file/d/0B_vlSjY0nNrkSFRVUERoTkF5cnM/view?usp=sharing
thanks a lot Mountains788, i try this two debrick.img, but no lucky, still the same mmc read failed
gigidel said:
thanks a lot Mountains788, i try this two debrick.img, but no lucky, still the same mmc read failed
Click to expand...
Click to collapse
I had the same issue, 2days ago (also so an Galaxy S4 mini).
I solved it by holding the 'volume down + home button' while connecting/disconnecting the phone to my/from laptop.
I have the same problem
When i put the sdcard with debrick image in my phone, It says:
BOOT RECOVERY MODE
CHECK BOOT PARTITONS..
COPY FROM T-FLASH..
BOOT RECOVERY..
WRITE 139008 sectors..
FLASH WRITE FAILURE
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: GT-I9190
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
BOOTLOADER RP SWREV: 2
WRITE PROTECTION: Enable
And when i connect it to pc to flash by odin, it says "There is no pit partition"
When i put the pit file in odin, it says the same
What should i do?
Did you get it to work? I have the exact same problem with the same phone (GT-I9190) !!!!
Hi all,
My note 2 is stuck on Samsung logo. It can enter download mode as well as recovery.
Download mode info:
ODIN MODE
PRODUCT NAME: GT-N7100
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV: A2
In recovery mode, first the android icon comes with exclamation mark. Then I see
E: failed to mount / efs
E: failed to mount / system
... and so on
I tried to flash stock rom using odin but it fails.
NAND Write Start!!
FAIL!!
Please help me fix it. Thanks!
gizmofreakz said:
Hi all,
My note 2 is stuck on Samsung logo. It can enter download mode as well as recovery.
Download mode info:
ODIN MODE
PRODUCT NAME: GT-N7100
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV: A2
In recovery mode, first the android icon comes with exclamation mark. Then I see
E: failed to mount / efs
E: failed to mount / system
... and so on
I tried to flash stock rom using odin but it fails.
NAND Write Start!!
FAIL!!
Please help me fix it. Thanks!
Click to expand...
Click to collapse
Open odin in pc
Connect device
Go to download mode
choose (BL) tab in odin and flash file in link below will fix all errors.
Boot into recovery
Do wipe cache & factory reset.
Reboot.
If doesn't boot flash stock rom then factory reset .
Reboot.
https://mega.nz/#!3YtWAQyb!4w5TjsBP2Br6YkRmra6GauNBgcTp_mRLxLrRkuCMghI
This file works only with note 2 exynos n7100 variant & s3 i9300 exynos.
Good luck.
Thanks!
I tried but I still get the same error.
NAND Write Start!!
FAIL!
Complete (Write) operation failed.
Trex888 said:
Open odin in pc
Connect device
Go to download mode
choose (BL) tab in odin and flash file in link below will fix all errors.
Boot into recovery
Do wipe cache & factory reset.
Reboot.
If doesn't boot flash stock rom then factory reset .
Reboot.
This file works only with note 2 exynos n7100 variant & s3 i9300 exynos.
Good luck.
Click to expand...
Click to collapse
gizmofreakz said:
Thanks!
I tried but I still get the same error.
NAND Write Start!!
FAIL!
Complete (Write) operation failed.
Click to expand...
Click to collapse
You have a corrupted NAND, you will need to replace the motherboard..sorry.
gizmofreakz said:
Thanks!
I tried but I still get the same error.
NAND Write Start!!
FAIL!
Complete (Write) operation failed.
Click to expand...
Click to collapse
Did you flash 4.2.2 kitkat stock rom ?
Because if you tried flash 4.1 jellybean it won't flash it will fail .
Try Flash Twrp recovery and flash any kitkat rom .
Hi guys,
hope you can help because I have no idea left.
Follwing situation. I have an GT-I9195 (LTE Version) on an older Cyanogenmod version (don't remember which one exactly) and got recently the "encryption unsuccessful" error during boot up. Okay, I know that's quite simple to fix, just reformat /data in recovery as ext4. But my old CWM recovery (6.0.5.1.) is not able to to change the file system and can not access /data at all (Error mounting /data).
Okay easy to fix - I thought - just update the recovery to TWRP and your good to go.
But doesn't matter what I tried, there is no way to change anything on this damn phone. And I tried a lot:
-tried to flash TWRP via Odin -->successful but no change on the phone (still on CWM 6.0.5.1.)
-tried to flash TWRP via Heimdall -->successful but no change on the phone (still on CWM 6.0.5.1.)
-tried factory reset and the whole story again --> no change at all
-tried 4 files stock firmware -->successful but no change on the phone (still on CWM 6.0.5.1. and on cyanogenmod with the encryption error)
-tried Re-Partition with separate PIT file with 4 files stock firmware -->successful but no change on the phone (still on CWM 6.0.5.1. and on cyanogenmod with the encryption error)
-tried Nand Erase and Re-Partition (4 files firmware) -->successful but no change on the phone (still on CWM 6.0.5.1. and on cyanogenmod with the encryption error)
So it seems I'm not able to flash anything. Tried different computer (with different OS), different cable, different Odin version (use 3.13 for the most trials but also an older one -->same results), so now I'm running out of ideas.
Might have something to do with "write protection enabled" or Bootloader version 2 or Kernel lock on 0x0...
This is whats written in the download mode:
PRODUCT NAME: GT-I9195
CURRENT BINARY: Custom
Knox KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
BOOTLOADER AP SWREV: 2
WRITE PROTECTION: Enable
Any ideas?
Thanks for your help!
ralrra