Anyone have a schematic or antenna connector pin outs? - HTC 10 Questions & Answers

Hey guys, I’m on my second screen replacement, this time replacing the battery as well. While disassembling, one of the antenna cable connectors broke off of the main board. It is the longer of the two from the top board. I need to know what this cable is for, and if one of these other extra unused connectors on the main board can be used instead. It would be EXTREMELY nice to have a schematic/diagram. Thanks In advance.

Related

Repair USB connector; possible or not?

Hello all.
I dropped my phone pretty hard the other day. I dropped it many times before so I didn't think there would be any damage besides that the battery popped out.
Once I got home and wanted to charge my Artemis I noticed that my USB connector is gone!
Well, I found myself a spare one on eBay, but as I looked at the connections on the circuit board of my Artemis I started to doubt the possibility to put another USB connector in there.
Some pins seem to be damaged real bad but not all of them, and then again I only want to be able to charge my phone and will not use the USB connector for syncing or using a headphone.
Can someone take a look at the picture I took and see if its still possible to attach a new USB connector to my Artemis and if it will at least be able to charge the battery?
Photo of circuit board:
Many thanks!
Repair of the USB mini port
Hey,
Could you send a picture with more sharpness, because i can't see it that well.
I already see that you have been soldering on top (close to your serial number).
Kind Regards
Bramatus
As long as you have got the correct connector then the way you do it is to remove the solder that is on the pads on the board and apply solder PASTE to the pins of the connector, then with a very COOL soldering iron gently touch the pins just long enough to flow the solder on.

exec mainboard issue

evenin all, ill keep it short,
the mini usb connector on the mainboard has broken off, some of the solder p=ads are damaged, i need a replacement mainboard, can anyone help??
thanks in advanced
sythen said:
evenin all, ill keep it short,
the mini usb connector on the mainboard has broken off, some of the solder p=ads are damaged, i need a replacement mainboard, can anyone help??
thanks in advanced
Click to expand...
Click to collapse
I suggest you try to post a Wanted ad in the Marketplace section. If anyone has one to offer, that's your best chance.
I´m sure I saw today someone selling Universal parts, not sure if motherboard...
sythen said:
evenin all, ill keep it short,
the mini usb connector on the mainboard has broken off, some of the solder p=ads are damaged, i need a replacement mainboard, can anyone help??
thanks in advanced
Click to expand...
Click to collapse
You may use some thin cable (to use as jumper) in case the pads are broken and connect to nearest point.
Also you can buy a cheap card reader which has the same mini-usb connector. Desolder it and connect to the uni if your usb connector itself is broken.
the USB connector itself is sold on eBay for around $5, works very well on Uni or any device with the same connector. However, if the pads are damaged, it might be impossible to have one reattached.
I can offer Mda Pro's motherboard. Working good. Once fell down and display was damaged..
Message me if good for you.
yeah, some of the pads a fubar, thanks for the help people
Broken USB repair
I notice you live in the UK, I can fix the USB connector for you. Even if the pads are missing there are some test points on the board that you can solder fine wires to. I have done half a dozen of these repairs so far, this seems to be the most common problem with the Uni, even more so than borken screens. One of these days I'll have to do a 'how to' guide for it.
that would be nice, my soldering skills are up to the job, i just dont know how too, if you drop me a pm or something we can discuss it further
thanks
Guys, if you could jot down what you do and perhaps a piccy of the solder points, this would be great to put in the Wiki.
Hello people,
If its any help, my usb connection came off twice. both times it was resoldered back on with a standard soldering iron with the tip made to a point, and it still works OK. I found it easy to do, just needs a steady hand.
Regads
Jay
thats all well and good. but the copper pads that are used to solder the connector to the mainboard are fubar, so no amount of soldering will help

[Q] Micro USB part (desoldering)

The micro-USB connector on my HTC Desire is damaged. Charging is not a problem. However, trying to connect it to a computer causes shows flaky behavior. I took it into the vendor who are estimating a charge of $140 to fix it.
I can solder/desolder the connector quite easily as I have SMT facilities at work.
I would like to source the connector first however.
Anyone know the part number or where I can source one from?
Hi
try to sample one from eg Molex.com
I think you have to pay for the shipping oid
http://www.molex.com/molex/products...pageTitle=Introduction&parentKey=usb_products
Good luck
Thanks.
Would be good to get a more definitive part. Dont want to desolder and realize I have the wrong part.
Has anyone seen the unsoldered PCB footprint for the device?
Is the connector a bottom or midmount?
Images taken from the HTC disassembly video (is on youtube)
But maybe there's just a cold solder joint and you don't have to replace the whole connector.
Thanks. Those pictures are neat. I took some of my own after opening up the back casing.
The damage is inside the connector (the cable wont stay connected). So not a dry solder joint problem.
I guess I could try and buy a few different connectors and try to see which fits.

PCB Connector Replacement

A few month's ago I'd ordered a LCD screen replacement for my incredible, and so when I got back from work o immediately took out the LCD from the package and started taking out my old broken. For me it was my first time experience replacing an LCD phone screen, anyways back to what I was going to say was when I unplugged the connector for the screen and the motherboard itself, after attempt to plug the connectors back together; the display connector plugged in perfect while the connector for the motherboard didn't do so well. The white piece that covers the PCB Connector, it tears a little bit off and I'd tried to power on the phone, meanwhile it didn't I tried again and things got worst. So I search online for a PCB Connector and see one, so I decided to and try to rip off the PCB Connector and plan to order the PCB Connector. So the part to attempt ripping off the PCB Connector didn't go so well, and stop there before things got worst. Any suggestions how I can replace that? I can't just leave my phone in my room and have to cover in dust. I need my phone back, how can I fix these? I know this thread seems long but I tries but it details for you guys.

microsolder replacement fpc connector to motherboard of htc one m8

I am practicing microsoldering skills, as I enjoy repairing broken phones. I have opened up htc one m8 and taken it apart and replaced broken screen, battery and daughterboard. However the phone has a broken connector for the second daughterboard cable. I cannot find out what this actual cable is called, it is on the top left of the motherboard, and is a very short cable, bent from the daughterboard. I have attached photos. Please can anyone identify this cable for me so that I can purchase the correct fpc connector?

Categories

Resources