The GPEL screen protector is fantastic! No dot matrix, full adhesive, comes with 2, affordable, case friendly & no Halo affect.
The black border is just a tad too big, so you lose a row of pixels..
https://www.amazon.com/dp/B07D1CG8QY/ref=cm_sw_r_cp_apa_MQYCBbYM79AP7
Thanks for sharing the review!
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Al3xxxinho said:
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Click to expand...
Click to collapse
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
So, anyone that sells this internationally for less than 15usd for shipping?
8bitbang said:
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
Click to expand...
Click to collapse
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Sent from my LM-G710VM using Tapatalk
markfm said:
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Click to expand...
Click to collapse
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
8bitbang said:
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
Click to expand...
Click to collapse
Sure, thanks!
Sent from my LM-G710VM using Tapatalk
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
8bitbang said:
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
Click to expand...
Click to collapse
What are the sensor impacts from using the gpel?
Sent from my LM-G710VM using Tapatalk
markfm said:
What are the sensor impacts from using the gpel?
Click to expand...
Click to collapse
It can cause the display to dim and sometimes turn off like when you raise your phone to answer a call. To be fair all full cover screen protectors are suffering for this flaw. Even OtterBox is getting massive hate for their version and is temporary unavailable.
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors, but with a catch: you have to align it with the sensor being more towards the bottom than dead center. My very first screen protector had it more towards the top (basically, the entire protector aligned downwards 1mm, which made the notch very prominent). Then I wasted two more trying to make it bottom aligned. (edit). That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first (edit) align the ridged sensor so it's almost touching the bottom cutout) and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Falkentyne said:
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors. That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Click to expand...
Click to collapse
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
8bitbang said:
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
Click to expand...
Click to collapse
My proof is me owning the phone and going through 4 GPEL screen protectors before I got it perfect. I paid my dues. And as someone disabled and on SSI and with a fixed income, I don't have money to go through infinite screen protectors, unlike some of you people here.
The trick is to align the "ridged" sensor so that it's (edit: just looked at my phone: the hole aligned at the -bottom- of the ridged sensor, rather than dead center! but not blocked by the edge of the screen protector), sensor bottom aligned and then after that, making sure all the sides are perfectly straight when applying (a LOT harder than you think, even in a steamy shower, because I'm in an old apartment). Took me 4 protectors and cost me over $30 dollars. (air bubbles and dust from me constantly having to re-lift to get the orientation perfect and eventually dust getting under the edges, and I have OCD so I want nothing less than perfection). Might even give GPEL an email and see if they'll send me an extra sample for my troubles. And no, I have no way to take a picture of the phone screen for you.
I forgot that I had it 'bottom' side sensor aligned rather than mid sensor aligned because I spent over 30 minutes in the shower sweating and uncomfortable wasting screen protectors trying to get rid of the notch line and getting it on with air bubbles. I was extremely stressed out, and it's difficult for someone with a metal bar in their spine to have to work that hard. Needless to say the fourth protector (thank god) I got absolutely perfect.
If it's dead center yes you will have a pixel row of the notch visible. So you have to 'raise' the protector upwards by that same pixel space. There's enough cutout to work with to make that work.
This is no problem because the very *BOTTOM* of the phone isn't used by the display (since this is an IPS display; someone mentioned this in a review, compared to OLED), unlike the top, so you have like 1mm of extra room to work with for the cutout (as long as the top sensor isn't blocked by the bottom edge of the protector). The black border at the bottom won't interfere with anything (checked with a screen test in the service menu).
I'll -try- to upload a picture of the phone with my laptop's built in camera if I can later on, but please don't be upset if you don't like the quality. My laptop isn't high definition and isn't made for such precise pictures. 720p isn't going to work very well.
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
This is the best I could do.
markfm said:
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
Click to expand...
Click to collapse
In your picture, move the screen protector UP about 1mm upwards so the bottom is where the red line is.
This will leave about 1mm of 'extra' space above the sensor area (whatever that thing is, sensor, microphone, I don't know). But it will still fit fully into the enclosure.
Took me 4 screen protectors to do this AND have no spare dust hairs from all the relifting !
Perfect thanks!
Just over the bottom edge of the front speaker (the oval on the right with the grid pattern).
I just got my gpel protectors in today, will give it a try tomorrow.
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
markfm said:
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
Click to expand...
Click to collapse
Glad you got it working and got the results you wanted.
It's good that the cutout is slightly larger than the speaker(and sensor/camera) itself, but bad that people won't know about this without experimentation (or somehow coming across the posts here).
Related
The little plastic bits at each side of the keyboard. I've just noticed them now. They're like the screen protecter film you get on electronic devices. I wonder if they indicate areas of possible wear and tear
Yes ... they are at the rear of the keyboard and on the underside of the screen half as well.
I found with mine that at the back there were a couple of scratches in this plastic indicating that the mechanism was so tight that it did mark. Hard to say what it would be like over time.
Did you check your PM re the screen ?
Also ... can you confirm your tilt is very stiff ... particularly the initial movement ... and that when you push the screen back down, just before it goes flat ... that you get a distinct click like a dislocation ?
Paul.
pgamble said:
Yes ... they are at the rear of the keyboard and on the underside of the screen half as well.
I found with mine that at the back there were a couple of scratches in this plastic indicating that the mechanism was so tight that it did mark. Hard to say what it would be like over time.
Did you check your PM re the screen ?
Also ... can you confirm your tilt is very stiff ... particularly the initial movement ... and that when you push the screen back down, just before it goes flat ... that you get a distinct click like a dislocation ?
Paul.
Click to expand...
Click to collapse
Paul, I just got mine today and you are right, the tilt is stiff at the initial movement and it also has a click (mechanical) sound just before it goes flat.
as far as scratches are concerned, there are none that i can see.
however, there seems to be a gap between the keys and the screen panel, so there should be no problem in that area pertaining to scratches or friction.
Any sign of that pinched top surface about 1/2" down from the top as the front surface touches the left chrome edge ?
pgamble said:
Any sign of that pinched top surface about 1/2" down from the top as the front surface touches the left chrome edge ?
Click to expand...
Click to collapse
Well if the screen is facing towards me then this is happening on the right side surface. Also the protector on the right side (of the keyboard) is a bit worn out so may be that is the reason.
Do you think removing the protector (from either sides of keyboard) will result in scratches?
I too have a stiff one. Yes, the tilt. And when I tilt it back again it has a click. I think the phone feels strong and well-made. I'm already happy with it.
Gutted that I screwed up putting the screen protector on.
<starts searching for new screen protector>
rb14 said:
I too have a stiff one. >
Click to expand...
Click to collapse
lol, you'll just have to play with it for a bit...
rb14 said:
I too have a stiff one. And when I tilt it back again it has a click.
Click to expand...
Click to collapse
LOL, that's too funny! Sounds like a viagra commercial
Tomo said:
The little plastic bits at each side of the keyboard. I've just noticed them now. They're like the screen protecter film you get on electronic devices. I wonder if they indicate areas of possible wear and tear
Click to expand...
Click to collapse
The left-hand plastic managed to get tangled up in the slide mechanism this morning. Was a bit of a mission to get it out but I'm just gonna get rid of that bit. Will leave the right side on for the time being.
Incidentally, the screen protector in the box is very soft and gets marked really easily!
dazultra2000 said:
The left-hand plastic managed to get tangled up in the slide mechanism this morning. Was a bit of a mission to get it out but I'm just gonna get rid of that bit. Will leave the right side on for the time being.
Incidentally, the screen protector in the box is very soft and gets marked really easily!
Click to expand...
Click to collapse
If you remove one, I would remove the other one too. Otherwise on side of the screen will experience more friction, what can't be good for the ballance.
I knew you lot would get all double entendrey with that post. For the record, I've been playing with it lots all over the weekend and it's not got any softer. Still nice and firm.
Don't. Just don't.
I just got two new XO Skins screen protectors for my wife's and my Moto X, and they are NOT cut out to fit the phone correctly. It looks like a manufacturing screw up, because the right side doesn't have smoothly rounded corners, and that's the side that doesn't line up correctly. So basically, if you line up the sides of protector with the edges of the screen, the cutouts don't line up with the speaker/camera/mic correctly, and if you line up the cutouts, the right side of the protector hangs over the edge of the phone.
I've tried to contact their CS about it, but haven't gotten a reply yet.
I finally got a reply tonight that they are sending replacements. I'll update this post after they arrive.
Sent from my Nexus 7 using Tapatalk 4
The replacements arrived, and they are exactly like the originals. I'm sending all of them back for refund and trying something else. I snapped some pics and if the issues show up very well I will post them here.
Wade-0 said:
The replacements arrived, and they are exactly like the originals. I'm sending all of them back for refund and trying something else. I snapped some pics and if the issues show up very well I will post them here.
Click to expand...
Click to collapse
Post 'em!
Ok, I took a couple pics to show the fitment issues. These were all taken with the screen on dry, because it shows up way better than when it's applied wet, so ignore the bubbles. The first pic is mostly to demonstrate where the cutouts are if you centered the film on the screen (the top is still a bit too much to the right, but it's hard to position these things when they are dry). The second pic is with the cutouts for the mic and camera aligned as closely as possible to show how much the film hangs off the right edge, and the giant gap on the left edge.
The other thing I think you can see pretty well is how smoothly the upper right and lower left corners are radiused, while the upper left and lower right corners have a point.
Wade-0 said:
Ok, I took a couple pics to show the fitment issues. These were all taken with the screen on dry, because it shows up way better than when it's applied wet, so ignore the bubbles. The first pic is mostly to demonstrate where the cutouts are if you centered the film on the screen (the top is still a bit too much to the right, but it's hard to position these things when they are dry). The second pic is with the cutouts for the mic and camera aligned as closely as possible to show how much the film hangs off the right edge, and the giant gap on the left edge.
The other thing I think you can see pretty well is how smoothly the upper right and lower left corners are radiused, while the upper left and lower right corners have a point.
Click to expand...
Click to collapse
That's awful. Geez
Late to the party, but I ordered these for poops and giggles because of credit I had and I will also confirm that they do not fit properly. Not even close and pretty pathetic IMHO.
Waiting on some Xtreme Guards to show up.
kraamerica said:
Late to the party, but I ordered these for poops and giggles because of credit I had and I will also confirm that they do not fit properly. Not even close and pretty pathetic IMHO.
Waiting on some Xtreme Guards to show up.
Click to expand...
Click to collapse
I'm waiting on a response from them so I can return them for a refund, and they are conveniently ignoring my request for an RMA. They have a 30 day money back guarantee, but apparently they are just waiting until day 31 to respond with the RMA. We are currently at day 29. I'll never recommend or do business with these clowns again.
http://www.amazon.com/Skinomi-TechSkin-Motorola-Protector-Lifetime/dp/B00D49OUSW
I always get a few Skinomis... perfect fit and case-friendly (currently using Air Jacket Grip). Highly recommended. Five stars IMO.
Finally got a response from XO after threatening to dispute the charge with Paypal, they gave me a full refund. I had a credit with Motorola so I bought some of their Power Support "Brilliant" screen protectors, we'll see how that goes. I have a feeling at some point I'll be putting a wet-application protector on, so probably will check out the Skinomi at that point.
So far, for the first 24 hours I really enjoy this phone. I only have one gripe so far. Has anyone noticed the light leak between the glass and the bezel on both sides?
See the attached pictures. If you're using your phone in a low light room with the screen turned up just a little bit and brightness comma there's a major Gap between the glass and the bezel that goes all the way down to the bottom.
sebastianraven said:
So far, for the first 24 hours I really enjoy this phone. I only have one gripe so far. Has anyone noticed the light leak between the glass and the bezel on both sides?
See the attached pictures. If you're using your phone in a low light room with the screen turned up just a little bit and brightness comma there's a major Gap between the glass and the bezel that goes all the way down to the bottom.
Click to expand...
Click to collapse
Imagine a fiber optic cable. That is the effect you are getting from the glass on the screen. Had the edges of the screen been painted black, you wouldn't see this. It's nothing to be concerned with.
ZiprLips said:
Imagine a fiber optic cable. That is the effect you are getting from the glass on the screen. Had the edges of the screen been painted black, you wouldn't see this. It's nothing to be concerned with.
Click to expand...
Click to collapse
I get that, but I guess I'm comparing this to S7 Edge and my wife's S6 Edge Plus.
*I was just about to write both don't do that but I'm wrong. I just turned up the brightness on both and they both have that issue. It's a small thing, but now I can't "not" see it.
Yes, that is normal. Besides, AMOLED screens are self-lit pixels, ie. there's no backlight to leak out, unlike conventional LCD screens.
Hi all,
We all know how hard it is to find a good Tempered glass for a smartphone with curving edge display,
That also the case with our Pixel 2 XL
Luckily, finally i managed to found tempered glass that has full adhesive, case friendly, and doesn't break our bank account, :laugh:
Here's the product : Tempered Glass for Google Pixel 2XL Screen Protector FULL GLUE Case Friendly Premium Screen Glass Protector For Google Pixel2XL
http://s.aliexpress.com/qqYVbYFZ?fromSns=Copy to Clipboard
(from AliExpress Android)
Price : $11.77 include free shipping,
It took week till it arrive to my door. Item shipped from Hongkong, am living in Indonesia
Packaging : its good and safe. Tempered glass placed inside a sterofoam box .
Installation : Now, this is the tricky part, although it has full adhesive, the installation wont go as simple as installing other (ex iPhone) full adhesive TG. It (the adhesive) tends to spread unevenly causing bubble.
The trick is to go from the corner, while keep the other corner floating, press the glass with two or more finger ensuring no bubble appear in the process.
It will take sometimes till you get it right with zero bubble,
But the result is rewarding. It perfectly fit, and can be used with cases as well. I use it with original google fabric case.
Check some pictures bellow :
Pictures with screen on and on a straight angle?
scottjal said:
Pictures with screen on and on a straight angle?
Click to expand...
Click to collapse
Like this ?
scottjal said:
Pictures with screen on and on a straight angle?
Click to expand...
Click to collapse
Sorry, forgot to turn off the portrait mode
Yes. Doesn't look like it cuts off the edges too badly. What I was waiting on but not sure I want to deal with Ali.
scottjal said:
Yes. Doesn't look like it cuts off the edges too badly. What I was waiting on but not sure I want to deal with Ali.
Click to expand...
Click to collapse
It was quite gambling for me as well, lol,
But since i have no other option available in my country, u guess i have nothing to lose for 12 bucks.
Now am waiting a case to arrive
Looks good. I just don't understand why they make the top and bottom black instead of clear if it is full adhesive.
I'm guessing this is the same product as HeroShield. Looks the same. My HeroShield should arrive in a few weeks, so we'll see.
Does it have a cut out for the proximity sensor? I don't mean just a transparent window, proper gap/no glass bit over the sensor. I can't see from the photos
how is the screen feel and oleophobic coating? Does the finger glide eaily on the screen?
kyacrash said:
Looks good. I just don't understand why they make the top and bottom black instead of clear if it is full adhesive.
Click to expand...
Click to collapse
Its because although the adhesive on the display area is full, there's lil gap on the edge area where it doesn't have the adhesive, i guess due to the curve, it still not possible to create fully transparent glass protector with full adhesive. I never seen one for popular phone like iphone either. All iphone x glass protector has coloring as well.
The only real transparent protector with full adhesive is whitestone probably, but thats using low viscosity loca to begin with, so its different story, not to mention the skyhigh price.
mkouk said:
Does it have a cut out for the proximity sensor? I don't mean just a transparent window, proper gap/no glass bit over the sensor. I can't see from the photos
Click to expand...
Click to collapse
It doesn't. It have a transparent window with adhesive under . It stick perfectly though, thus no interference to the proximity function. I try make a call and place finger over the sensor, it work normally
Mikulec said:
how is the screen feel and oleophobic coating? Does the finger glide eaily on the screen?
Click to expand...
Click to collapse
Nothing extraordinary regarding the coating i guess. Finger glide nicely just like on original screen. But it collecting fingerprint overtime. (Am one of those guy who have wet hand all the time though, so my experience with fingerprint might be severe than how it should) :silly:
ordered! hope it will arrive soon!
btw do you have to tear it out to re position it when you are applying on the screen?
bradputt said:
ordered! hope it will arrive soon!
btw do you have to tear it out to re position it when you are applying on the screen?
Click to expand...
Click to collapse
You need to lift it off if you already stick large area of it prior to reposition,
Positioning is quite easy though, the harder part is to push the glass slow and even.
I'd almost be interested, but I try to stay away from protectors that cover the proximity sensor. I know it works sometimes, I've just been bitten by it too many times on phones where it causes issues.
Here's HeroShield's install video. Seems like they include a squeegee with theirs to help with the bubbles.
Mine comes today, so I'll see what it's like too.
ilal2ielli said:
Here's HeroShield's install video. Seems like they include a squeegee with theirs to help with the bubbles.
Mine comes today, so I'll see what it's like too.
Click to expand...
Click to collapse
These look interesting. I am with the previous poster about the prox sensor cut out. Please share your experience when you get it.
kiru said:
These look interesting. I am with the previous poster about the prox sensor cut out. Please share your experience when you get it.
Click to expand...
Click to collapse
Can see from the video that it has glass covering the sensor, so it will be hit or miss. Some will have no issues with the sensor. Others will.
Mine will be here in a few weeks, so I'll see then too.
Hi OP... Are you able to post some picts of the top and bottom edge of the phone? Or a pict that can somehow show the gap of the side of the protector to where it meets the screen. Just curious to see if there is a slight gap as there is no adhesive there. Since I go case less, I am afraid I will always crack the glass because of this gap. Thanks in advance!
Something like this ?
Those picts are good!!! thanks!!!
Hello all!
First time posting in a while, so forgive me if I'm a bit rusty. I just got my Samsung Galaxy Note 10+ yesterday, and my amFilm Ultra Glass Screen Protector today, so I thought I'd write up a little review. Sorry for no pics, but I was busy installing and trying to keep things dust-free
I've used Whitestone in the past but was disappointed with both my Note 8 and 9 installs, primarily because of the LOCA spiderwebbing on the edges. I figured I'd give another brand a shot, so I went searching here and found the amFilm Ultra Glass Screen Protector. A quick trip over to Amazon, and $40 later (for a full kit including *2* protectors) and here we are!
PACKAGING: The box is nice - wider and flatter than the WS product. It's clean and simple, but professional looking. Plus their website and install video are well done also. Inside the outer box are three smaller boxes. The largest contains the plastic frame, screen protectors, and wipes (I think). The medium size box contains the UV light and the MicroUSB cable. It appears to be identical to the WS product, but I don't know this for a fact, so take that for what it's worth. The smallest box contains the LOCA (2 tubes), extra absorption pads, plastic pin, tabs to place over the speaker, a bubble level, and a weight. Everything you need comes in this kit, including plenty of wet and dry wipes, microfiber cloths, and dust removal stickers. On the packaging is a QR code to go to the install video.
PRODUCT: Everything seems to be on the same quality scale as the WS product, with a few minor changes - 1) there is no LOCA applicator "bridge", you have to aim and dribble the solution by hand, 2) the pin is different - there's no more tilting the entire phone to move the liquid into position - the pin is angled and sets the glass down at an angle, and 3) the "fingerprint" weight (more on this later). Otherwise, if you've done the WS before, this isn't significantly different.
INSTALLATION: **REMINDER** REMOVE the factory plastic screen protector and clean your screen THOROUGHLY before proceeding! I ALMOST forgot, which would have been a disaster! I watched the video twice and didn't see any mention of this, so amFilm, here's a tip for you Anyway, installation is straightforward -put the little feet on the bottom of the phone to bring it flush with the pins inside, make sure the screen is 100% clean, install the sticker over the speaker, apply the liquid (making sure to absorb any "splatter" before proceeding!), peel the protective film off the glass, place it, and pull the pin. Once the liquid starts to spread, put the weight where the fingerprint sensor is and let it settle and "ooze" for 3-ish minutes. (NOTE - it's hard to locate the fingerprint scanner, so you might want to mark the frame in advance with a Sharpie (another tip for amFilm - marking that plastic with some kind of raised bumps or hash marks might be a good idea, or maybe a film for on top of the glass that marks where to place it - just a thought). After that, it's bake-time under the UV light, then you're done.
RESULTS: I'm very impressed so far. The glass appears to be nice and clear, and I can't even see the little "spots" in the corners others mentioned. I lucked out this time and no dust specs at all. No bubbles, etc. the fingerprint scanner appears to be working fine, although I haven't re-registered anything. It DOES require a little extra "umph" to scan, but that's not a big deal. Part of that could be me getting used to an in-screen scanner. There was minimal over-oozing, and the pre-installed pads absorbed everything fine. Barely needed a wipedown afterward.
FITMENT: There appears to be no flaws in placement using the guide, or in the fitment of the glass. It sits flat, and lines up exactly where it should. The cutout for the front-facing camera is exactly where it should be, and it's not overly-exaggerated in size. The edges leave plenty of room for putting the phone in a case (I've tried 4 so far, all fit without touching the glass edge, so there's no worry about case push on the glue). The bottom edge is just a tad bit short, maybe a 1/16", but that could be allowing for larger cases (I don't use the big bulky ones, so IDK).
OVERALL ASSESSMENT: 4.5/5 Stars - Great product, especially for the price. I'll keep you posted on long-term wear & quality, but for now, I'd say it's a great deal versus the competition.
Thanks for the feedback, just got my note 10 plus and am trying to filter out the paid/promo reviews vs legit ones.
I may go this route with amfilm as well. i bought the tech matte clear case, so i hope it fits well within it without popping off.
hows your experience after putting it in a case?
I applied mine the other day, and while I'm happy with the fit & finish, my fingerprint reader is spotty at best. In addition, my frame snapped, so I need to contact customer support to send me another one. because it snapped it ended up leaking LOCA all over the place, too.
entropism said:
I applied mine the other day, and while I'm happy with the fit & finish, my fingerprint reader is spotty at best. In addition, my frame snapped, so I need to contact customer support to send me another one. because it snapped it ended up leaking LOCA all over the place, too.
Click to expand...
Click to collapse
Isn't that glue suppose to cure? When you say it snapped did it spill liquid after the snap?
joogle said:
Isn't that glue suppose to cure? When you say it snapped did it spill liquid after the snap?
Click to expand...
Click to collapse
The frame snapped during install, without me noticing. Because it wasn't holding everything in place very well, the glue ran EVERYWHERE. Under the phone, over the sides, etc.
So yes, once I got everything fixed as well as I could, the glue cured fine. But you don't cure it until you're basically done and ready to go.
entropism said:
The frame snapped during install, without me noticing. Because it wasn't holding everything in place very well, the glue ran EVERYWHERE. Under the phone, over the sides, etc.
So yes, once I got everything fixed as well as I could, the glue cured fine. But you don't cure it until you're basically done and ready to go.
Click to expand...
Click to collapse
If you turn sensitivity on, does that resolve the fingerprint issue?
No, sensitivity is already up. I’ll have to replace the protector soon anyways, we’ll see if another install will make things better.
entropism said:
No, sensitivity is already up. I’ll have to replace the protector soon anyways, we’ll see if another install will make things better.
Click to expand...
Click to collapse
The September update includes improved finger printer recognition.
Ok I decided to go ahead and buy the amfilm note 10 plus screen protector from Amazon. Watched their video and then another on Youtube like twice. I think I got the install right, the whole weight placing situation is a guesstimate, if they are reading this thread - put something on the tray to take the guessing out of the process, like a stick with a weight so it stays in one spot.
Also, the glue stick - be careful when lifting it to make sure no drop falls out - i didnt put the black cap back on - saw an extra few big drops fall on my desk - no biggie - but if it was on the screen would have been a hassle.
then the UV light shuts off at 45 seconds - their last instruction is to keep it lit for 60 seconds - they should probably adjust it - again not a big issue.
in terms of quality of the screen protector - looks good - its a thin piece of glass - hopefully it protects the screen. the fingerprint sensor - its been a hit/miss kind of. i added my same thumb print twice, sometimes it has to read directly in the middle of the thumb, othertimes i feel like i have to press harder. I didn't try the fingerprint sensor before the screen protector so don't know if its just the way it is.
I would rate this like 3.5 / 5 -- i think tempered glass is solid, the fingerprint sensor can be annoying, its not really that smooth like if you slightly put your finger/thumb on it that it will open. like literally it won't take it on first try, on second or third try it will take - that is the most annoying part about it.
the install process was decent, as long as you watch the videos first - its straight forward.
price wise its sucky - i wish they would sell this for $20 - even with just one screen protector. $40 is steep, replacement protectors they can probably price between $7 to $10 i feel.
By the way this is the same UV type device used to cure fingernail paint - lol - your household may already have one.
I don't have the Whitestone to compare to. But I can say man the Samsung film screen protector is solid, used it for few days, even when taking it off it was on perfectly. I kind of miss it but i think tempered glass will offer more protection on a fall.
Pictures, please.
https://www.amazon.com/dp/B07VKHMK9J/ref=cm_sw_r_fm_apa_i_2oX0DbYMHRS0A
I've installed two of these protectors on a note 10 + and a note 10. I did have the issue with the frame cracking with the note 10+ but the company has since fixed that issue.
I've used WDG for a few years now and this one has exceeded my expectations and is better than Whitestone.
The installation is simple and comes with a weighted cylinder that's used when you're curing the glass with the UV light. I've had zero issues with the finger scanner as well as my daughter on her note 10. I actually put the cylinder on while the glue was spreading. I can actually see a circle where the finger print scanner is at and I think this is a recipe for success. I've installed these just after release and they still look brand new. Scanner works great! I can provide forage if anyone is interested. The price is great for getting two in the box. I highly recommend!