Reboot/shut off problem during charge. - Verizon Samsung Galaxy Note 8 Questions & Answers

Need some help XDA family.
Not sure if the Oreo update is responsible for my issue or not. But everytime I try and charge my phone in my car, and the ambient temperature and device temp are around 75 degrees, the device will shut down as soon as I plug it in, but it will charge the phone. The device is in no way hot. And if I try and turn it back on from this state, it will bootloop. Until I've hit it with some air conditioning. It never did this because I got the phone and updated it to Oreo in the winter time. And I always charged it in my car with an official Samsung fast car charger. It's like a security guard that gets triggered way too early.
Has anyone else had this problem?
Any ideas?
Kinda worried that it won't work when I need it. And I never had these problems with my Note5 or any other phone to be honest.
Thanks.

same issue with my verizon note 8
I'm having the same issue, not just with my car charger but also with multiple wall chargers. if I wait to charge it till it is less than 50%, it will charge for a few moments then shut down and keep charging. if I leave it alone till its at 70-80% it will normally boot up ok, if I try to reboot it right away I get into the same boot loop (clearing cache and safe mode do not consistently get it to boot correctly). This has been happening for a few months off and on but is getting much more consistent the last few weeks. I've even tried wireless charging rather than wired but that didn't seem to help. i'm thinking it is a battery issue. did you ever get a fix?
thanks,
James
Jjavitable22 said:
Need some help XDA family.
Not sure if the Oreo update is responsible for my issue or not. But everytime I try and charge my phone in my car, and the ambient temperature and device temp are around 75 degrees, the device will shut down as soon as I plug it in, but it will charge the phone. The device is in no way hot. And if I try and turn it back on from this state, it will bootloop. Until I've hit it with some air conditioning. It never did this because I got the phone and updated it to Oreo in the winter time. And I always charged it in my car with an official Samsung fast car charger. It's like a security guard that gets triggered way too early.
Has anyone else had this problem?
Any ideas?
Kinda worried that it won't work when I need it. And I never had these problems with my Note5 or any other phone to be honest.
Thanks.
Click to expand...
Click to collapse

Related

Not Charging After Full Drain. Not Turning On When Plugged In

So I'm having a problem where I drained my battery and the phone shut itself off with 1% to 2% battery life remaining. I've left it charging for a good 45 minutes now. Turned it on, and it reported 1%. Thinking that it was just a reporting error, I unplugged it, and the phone promptly shut itself off. Now another 30 minutes has passed, unplugged it, turned it on. The phone refuses to turn on! It will however show the battery charging animation, so I know it's not bricked or anything. I guess my only solution is to leave it charging while it's off overnight, even though I need to use my phone right now... That important person will have to wait :crying:
Edit: Works again... Though it does not show my battery life correctly. It says 15% when it's probably more like 2%.
Make sure it's plugged into a wall and not your computer.
Sent from my Optimus G using Tapatalk 2
BMelz said:
Make sure it's plugged into a wall and not your computer.
Sent from my Optimus G using Tapatalk 2
Click to expand...
Click to collapse
It was plugged in to the wall.
geokilla said:
It was plugged in to the wall.
Click to expand...
Click to collapse
Might want to use a different cable.. i have read that the cable and possibly even the wall adapter can be flakey.. if you have a spare cable try to use it instead of the lg one..
Original LG cable is fine. It's ever since I drained the battery it's started to act weird. I plugged it in at 3% in hopes of "calibrating" the batterystats and it was charging fine. Up till now. I caught a glimpse of my phone turn itself off while charging.
Now it's randomly decided to turn itself on and bootloop... And back to charging animation while off we go. What the hell? The battery isn't charging... Switching cables didn't help btw.
Found a third cable. Temporarily working..
geokilla said:
Original LG cable is fine. It's ever since I drained the battery it's started to act weird. I plugged it in at 3% in hopes of "calibrating" the batterystats and it was charging fine. Up till now. I caught a glimpse of my phone turn itself off while charging.
Now it's randomly decided to turn itself on and bootloop... And back to charging animation while off we go. What the hell? The battery isn't charging... Switching cables didn't help btw.
Found a third cable. Temporarily working..
Click to expand...
Click to collapse
Hmmm maybe the charger? Sounds to me like its not getting proper power hence the shutting down while plugged in.. but what do I know heh
I have the same problem. Plugged the phone in at about 3% and walked away. Came back an hour later to find it stuck in a loop of the LG logo and a black screen. I can sometimes get it into recovery, and from there see that the battery percentage will go from 0% to 15% and back to 0%. It's like the battery is bad.
I think it's a problem with the ROM/firmware where we can't drain it and hope to charge it up again..
I'm still running v1 of the jb release and last night I used my phone until it shut down at 2%, charged it up fine, and its been ok, knock on wood. One weird thing is that if I use the phone while on the charger, and I mean light tapatalk usage, the phone will drop to 99%, even while plugged in. Weird.
Sent from my LG-E971 using Tapatalk 2
ATRIXXIRTA said:
I'm still running v1 of the jb release and last night I used my phone until it shut down at 2%, charged it up fine, and its been ok, knock on wood. One weird thing is that if I use the phone while on the charger, and I mean light tapatalk usage, the phone will drop to 99%, even while plugged in. Weird.
Sent from my LG-E971 using Tapatalk 2
Click to expand...
Click to collapse
That's normal. When the phone is charged at 100% it stop charging to avoid the battery to be overcharged thus reducing it's durability.
Not charging again... My phone maintained a charge between 10% and 25% or so according to the battery usage graph. So I switched cables again. I went into the service menu and got a screenshot of the charging test this time. First pic is with the LG cable. Second is with a Samsung cable. Third picture is back with LG cable after the battery successfully got charged past the "low battery zone" with the Samsung cable.
I have a similar problem with the stock charger. After a few weeks of working perfectly, it just sopped charging my Optimus G.
Bizarrely, it charges my wife's Galaxy S2 HD LTE without issues.
And the charger from my Sony-Ericsson Xperia pro charges the Optimus without issues.
It's almost like the stock charger burns out something internally such that it doesn't output enough voltage/amperage/current.
Sent via the magic of an Optimus G (E971) running CM 10.1.
So it happened again... But this time, it occurred in between 20% to 40% battery life while charging. It's probably the LG cable.. Gonna call support and ask for another.
geokilla said:
So it happened again... But this time, it occurred in between 20% to 40% battery life while charging. It's probably the LG cable.. Gonna call support and ask for another.
Click to expand...
Click to collapse
I have a similar situation -- I powered down my phone one time at 5 %, did not wake up until one hour of charge, then last night tried again with about 40 % of battery left, same problem. I was wondering at first if the phone did not go to power down properly, and that the battery would drain through that, but then I just did another test with my battery at 30 %, and the phone did not want to restart until plugged in for 5 minutes.. It's almost as if the booting process is just this huge battery drain, sucking all the juice to start the phone in a peak of electrical rage.. anyway -- I noticed that yesterday, I was trying to restart the phone after a while, it would start to boot but it seemed it owuld just miss a little bit of juice to complete the process, then finally when it made it to screen it was at about 10 %..
Could it be that fix we used in the stock rom to get the screen at more than 65 %, and the cpu at 1512 mhz ? It seems more software related than hardware in my case, meaning I don't beleive it is the cable
Hate to revive an old thread, but as the new owner of an LGOG i just ran across this problem the other day. My phone has been able to go two day on a charge, and last week I forgot to charge it on night. Found it dead the next day. was leaving so I took it intending to charge at work or in the car. Car charger had no effect, but upper portion of phone got hot. plugged it in at home, same thing, charging icon, getting hot, but not charging. Also noted dim screen glow all the time.
tried 2o second hold on power button, vol up and down, got into the download screen and the bootloader screen, but no charge. Finally held the power button and vol. up and red charging light came on. Held it for a minute and the red charging light stayed on, let go out it went. Decided to try a couple of rubber bands around the phone to hold in the buttons, and it worked ---phone charged fully and operates as usual.
Thought I'd pass my experiance on to help anyone else with similar problem. Any idea why this worked?
I don't know, but I do know that getting to android 4.3 roms like the ones in Houstonn's thread have cured my O. G. from that, and from also constant and random camera reboot, and from also maps freaking out when plugged in in the car..
Sent from Somewhere using my Dog
For anybody that runs into this problem
I had this problem and tried for hours and hours to fix it. When you stick the usb charger into your phone, it literally takes like 5 hours to charge 2% when it's in this state
So it never gets to a point of wanting to turn on because the phone gets too hot trying to charge
My solution: Put a bunch of ice in a bowl, then put something over that like a bag, aluminum foil, basically anything that would be a barrier between the ice and your phone to keep it from getting wet
Now let it charge with the phone sitting on top of that ice for a few hours(make sure to add new ice as it melts) and your phone will charge up enough that it can be fully turned on. Then just let it keep charging
This worked for me after trying other things for hours. If this didn't work i was gonna open the phone and pull the battery
After the last update I have not had this issue. I've run my phone dead a few times and now it always charges - no issue.
philliboy said:
I had this problem and tried for hours and hours to fix it. When you stick the usb charger into your phone, it literally takes like 5 hours to charge 2% when it's in this state
So it never gets to a point of wanting to turn on because the phone gets too hot trying to charge
My solution: Put a bunch of ice in a bowl, then put something over that like a bag, aluminum foil, basically anything that would be a barrier between the ice and your phone to keep it from getting wet
Now let it charge with the phone sitting on top of that ice for a few hours(make sure to add new ice as it melts) and your phone will charge up enough that it can be fully turned on. Then just let it keep charging
This worked for me after trying other things for hours. If this didn't work i was gonna open the phone and pull the battery
Click to expand...
Click to collapse
matt832 said:
After the last update I have not had this issue. I've run my phone dead a few times and now it always charges - no issue.
Click to expand...
Click to collapse
What update are you referring to? I don't get over the air updates. Mine is off contract.
philliboy said:
What update are you referring to? I don't get over the air updates. Mine is off contract.
Click to expand...
Click to collapse
Last fall. I had to go to the stock rom, do the update, reroot, then all was fine.

New Moto 360 Only Charges When Powered Off

Weird defect. Anyone else have this problem?
Edit: as of now it won't charge at all
Edit 2: After a lot of fiddling around, it decided to charge. Working great except for a single dead pixel Got to exchange it on the 9th or whenever they get their shipment in.
Mine charges while powered on.
holabola said:
Weird defect. Anyone else have this problem?
Click to expand...
Click to collapse
Mine charges while on and off. What I did notice, is when I was initially setting it up it went up to 32% and while on charger it started loosing charge. I have no idea why this happened but assumed a service was running in the background. Ever since the initial setup, on or not the watch gains charge. Seemed to take about 2 hrs from near empty to full while the display was on showing time.
As of now it wont charge at all. This is driving me insane. I got it to 9% somehow but I have no idea, and Best Buy won't have any to replace it with.
holabola said:
As of now it wont charge at all. This is driving me insane. I got it to 9% somehow but I have no idea, and Best Buy won't have any to replace it with.
Click to expand...
Click to collapse
Do you have the cable that came with it plugged into the cradle? I started using my cell cable into the cradle and my battery percentage was going down instead of up.
My local Best Buy said of the two they had today the first sold wouldn't charge. I saw another post on reddit claiming theirs wouldn't turn on, could also be related to a charging issue.
pfroo40 said:
My local Best Buy said of the two they had today the first sold wouldn't charge. I saw another post on reddit claiming theirs wouldn't turn on, could also be related to a charging issue.
Click to expand...
Click to collapse
This is a ****ing pathetic launch. There is literally no stock anywhere and of the few that are sold a handful have defects. This is simply disgraceful.
Here's what happend with mine.
First time I powered it on it said to download the wear app..so I did that. Then, it proceeded to connect and pair with my phone. It started to download something, (wear update?) and at about the half way point it said charge your device, shutting down. So it shut down. I put it in the cradle and it initially had 23% charge. 5 minutes later it had 18%. Not knowing what was going on, I turned it back on and was met by a spinner that said just a minute... for about 15 minutes. So I turned it back off.
After another reboot I went into the menu and selected reset device. After this it began to charge.. all the way to 100%. I turned it back on and it re-downloaded what it had to and applied the update successfully after about 3 or 4 restarts and 10 minutes. Now all seems well.
Edit.. By well I mean working. It's been merely 3 hours and with almost no use I'm down 40%. FML
yeah, i think people in their rush to use it haven't charged them fully. i plan to charge mine fully before using it.
gammite said:
yeah, i think people in their rush to use it haven't charged them fully. i plan to charge mine fully before using it.
Click to expand...
Click to collapse
This was definitely my issue. The problem is the vagueness of the instructions. It basically says turn it on, download the app.. Show off (until it dies).
I had the same problem with it saying charge your battery. I put it on the charger and left. Came back, it installed an update, rebooted a couple times and then was good. I've been playing with it heavy for a few hours and it's at 69%.
Sent from my LG-D801 using Tapatalk
Phlip00ws6 said:
Here's what happend with mine.
First time I powered it on it said to download the wear app..so I did that. Then, it proceeded to connect and pair with my phone. It started to download something, (wear update?) and at about the half way point it said charge your device, shutting down. So it shut down. I put it in the cradle and it initially had 23% charge. 5 minutes later it had 18%. Not knowing what was going on, I turned it back on and was met by a spinner that said just a minute... for about 15 minutes. So I turned it back off.
After another reboot I went into the menu and selected reset device. After this it began to charge.. all the way to 100%. I turned it back on and it re-downloaded what it had to and applied the update successfully after about 3 or 4 restarts and 10 minutes. Now all seems well.
Edit.. By well I mean working. It's been merely 3 hours and with almost no use I'm down 40%. FML
Click to expand...
Click to collapse
So, I got mine to charge and everything. So far I LOVE IT. I made a post on working apps that I've tested over in the Themes and Apps subforum. Basically, I put it on the Qi Charger I have for my Nexus 5 DIRECTLY in the center and it ended up charging then stopping again. Then, this time, I put it on the charger provided, and it worked to 100%... Very strange but I plan on exchanging it anyway as there is a single dead pixel I can see.
Same issue... Got the watch. Turned it on in the car and it started the update without promoting me to do it and now it is in the same dead cycle I've seen others post about. it will sit on the charger for hours and only be a few percent and when u power it on it tries to update and goes from 10% to 0 in less than a min or two. I just did another reset and put it on the cradle. The only feedback I have that something is happening is the watch is pretty hot. My gear live and Galaxy Gear 1 had an icon that showed charging status when the phone was off. Also they charged quickly, we're always cold and had great battery life. I can't imagine Moto not testing these devices long enough to figure that it should not try to apply an update until the battery was at a certain level or plugged in. I wish when these reviewers do features on the engineers of these devices, like have been recently done instead of ass kissing these guys would at least do some calls g out on their process. It'll like when Apple came out with the IPhone 4 and showed all these unbelievable signal testing facilities and they couldn't figure out when you held the phone normally on your left hand that the signal would drop to zero. It literally took me 2 minutes to figure out that one...
I highly advise you sink a hour charge into the watch first at least. most of these new batteries are like a lithium ion / lipo hybrid. they have a low voltage cutoff so the battery cells don't get damaged and go kaboom. Noone knows how long these sat or what charge was in them, how cold and so on during shipping. I would say people are running them low enough moto is triggering low volt cutoff.the update may have even changed the voltage values they accept as tolerable. and when you power it up this tricks it into a fail mode. ost smart chargers see the low volt and refuse the to charge for risk of a damaged cell. this sounds a lot like moto 360's issues.
When mine hit 80% on the charge, the update downloaded, watch rebooted, and the charge message started appearing.

Won't boot or charge

Anyone having problems with it not powering up. It will charge to about 8-12% then shut off. It gets really hot when it's charging but I can't get anywhere with this watch. Getting really frustrated, been trying to get it work for over 5 hrs. Has anyone had this issue?
gshaw1967 said:
Anyone having problems with it not powering up. It will charge to about 8-12% then shut off. It gets really hot when it's charging but I can't get anywhere with this watch. Getting really frustrated, been trying to get it work for over 5 hrs. Has anyone had this issue?
Click to expand...
Click to collapse
Boot it up. Press and hold power button. Chose reset device from menu. When it boots back up don't touch until charged.
Definitely had issues like this. I ultimately exchanged it (got lucky with Best Buy having it in stock) but I read here that you may want to reset it, and charge it while its completely off, to full battery, Before trying to sync and use it. My defective 360 wouldn't even factory reset, so YMMV.
tcollum said:
Definitely had issues like this. I ultimately exchanged it (got lucky with Best Buy having it in stock) but I read here that you may want to reset it, and charge it while its completely off, to full battery, Before trying to sync and use it. My defective 360 wouldn't even factory reset, so YMMV.
Click to expand...
Click to collapse
dottat said:
Boot it up. Press and hold power button. Chose reset device from menu. When it boots back up don't touch until charged.
Click to expand...
Click to collapse
Thanks guys, that worked appreciate it! :good:
Don't pair it to your phone. A service kicks off to do an update but you can't until it's 80% or more charged. As others have said, do the rest then leave it alone.
Same thing happened for me.
reTARDIS said:
Don't pair it to your phone. A service kicks off to do an update but you can't until it's 80% or more charged. As others have said, do the rest then leave it alone.
Same thing happened for me.
Click to expand...
Click to collapse
I'm having the exact same issue. How do you know when it is charged fully? When it is off there is no indicator of charge level. The Galaxy gear and gear live I had both had a battery icon when charging while off. I hope the battery is not a dead since the gear and live watches had awesome battery life for me...
Like a dumbass i tried to pair without fully charging it and was unsuccessful. Now the watch is dead and on the charger. Hopefully it charges or I will have to return this.
It took me about 10 attempted charging cycles over 24 hours before it worked. Usually the watch was off and it would be pretty hot. I noticed the charger was only a .5a so I changed the adapter to a 1.8a one I had. I left the watch on where the blue circle and time was showing and it charged right up from 3 to 100 in about an hour and today I used it from 2pm till 1030 pm with ambient screen and it was down to 39 now on charger for about 20 mins and it is up to 77. So far so good after a nightmarish 1st day...
Sent from my LG-D850 using XDA Free mobile app
yeah, I'm noticing my watch feeling hot while being charged. Sadly, it still won't power on. :crying:
It will, just wait a little while then when it is on the cradle press the power button for 3-5secs then it will come on. On the stock charger you will prob see the power circle start dropping then shut off. Plug in a higher rated Micro USB charger into the dock and it should charge fine.
Sent from my LG-D850 using XDA Free mobile app
bruceo said:
It will, just wait a little while then when it is on the cradle press the power button for 3-5secs then it will come on. On the stock charger you will prob see the power circle start dropping then shut off. Plug in a higher rated Micro USB charger into the dock and it should charge fine.
Sent from my LG-D850 using XDA Free mobile app
Click to expand...
Click to collapse
Yeah, I was @ 3% and charging using the stock and it powered off my itself. but, now I'm on a higher charger so hope things get better. I'm so impatient right now. I just want to start playing with it. hehehe
bruceo said:
It will, just wait a little while then when it is on the cradle press the power button for 3-5secs then it will come on. On the stock charger you will prob see the power circle start dropping then shut off. Plug in a higher rated Micro USB charger into the dock and it should charge fine.
Sent from my LG-D850 using XDA Free mobile app
Click to expand...
Click to collapse
Is this safe for the hardware? My moto 360 keeps floating between two percentages after about 2 hours. I plugged in the charger from my note II, and it seems to charge really quick. But is this higher amperage safe for the moto 360, since the stock is rated at a much lower amperage?
RodrigoKim said:
Is this safe for the hardware? My moto 360 keeps floating between two percentages after about 2 hours. I plugged in the charger from my note II, and it seems to charge really quick. But is this higher amperage safe for the moto 360, since the stock is rated at a much lower amperage?
Click to expand...
Click to collapse
The device will draw what it needs a .5a charger will provide up to that amount of current. a 2a charger will provide up to 2a of current but a device may not pull that much. It is generally thought that for LiIon batteries that providing a low maximum current and taking longer to charge will make the batteries last longer, so if you dont mind a slow charge cycle, which for a watch that should be charged while you are sleeping it doesnt matter then you should go back to the stock adapter to maximize total life.
I went off charger at 7:30am and now at 11 I am at 65%, which is terrible, but I'll wait a week to pass judgement, but my gear live and galaxy gear 1 with tizen both had awesome battery life of 2 full days with more than moderate use.... The Galaxy Gear 1 on Android was lucky to get more than 14 hrs of use.
Thanks everyone for helping me get my Watch up and running. For anyone who is new and reading this, fully charge your watch before pairing it since it will need at least 80% battery so it can update itself. Of course, this has already been stated in the thread and thanks to those folks who stated it already and all the credit goes to them.
I'm having this issue as well. I've been trying to charge it for the past few hours and it never gets past 10%. I kept trying to reset the device and it would never work. It kept coming up in the "Just a minute" mode which seems to eat the battery.
But finally on my last reset attempt, the device rebooted immediately and came back up on the "Select language" screen. I now have the device charging and am hopeful it will work this time.
But my big question is: how do you know when it's fully charged? Without knowing what the current charge level is, I'm afraid to try the update procedure or I may get stuck in the same "Just a minute" loop again. Anyone have any ideas on how to determine the charge level prior to setting up the device?
I killed mine. I tried to pair, got stuck on the "just a minute" screen and then it died. I charged it for a couple of hours and it still would get stuck. Somehow, I got to settings (still don't know how) and did a factory reset. Then, everything seemed ok and it was charged at 100% when I paired and did the update.
However, after the update, I got into a boot loop where it would show the M logo with the marks around the dial, flash to some colored balls, then say "android wear" and then it would reboot. Tech support from Motorola couldn't help me and finally after a few hours the watch died. I put it back on the charger and it would eventually fire back up and go into the bootloop again. It did it all night last night.
Furthermore, my indicator on the charger never lit up either.
I took it back and "exchanged" it for a new one that the store said would ship this week.
As much as I was anticipating this thing showing up, I'm pretty disappointed already.
Finally got mine booted. After successfully resetting the device (back to the "select a language" screen), I had it on the charger for about an hour. Then I tried again and it went through the whole installation successfully.
Ugh! Wish I read this first. Unable to get it to turn on at all, cannot get it charged over 6%
Over Achiever said:
Ugh! Wish I read this first. Unable to get it to turn on at all, cannot get it charged over 6%
Click to expand...
Click to collapse
I was in the same boat. The trick is to get the device reset. When I was trying to do that (via the menu that comes up when you press-and-hold the watch button), it would sit there and do nothing. Then 10 seconds later it would power down. But then as it charged, it would power back up and the "Just a minute" message would appear.
To get it to work, I turned the device off and let it charge. When it powered back on, I turned it off immediately and kept charging it. Then eventually, the charge jumped up to about 13%. I tried the device reset option again and this time it powered down immediately and booted back up with the "select a language" screen. I then turned off the display and let it charge for an hour. After that, I went through the setup and it worked.
DanPLC said:
I was in the same boat. The trick is to get the device reset ... After that, I went through the setup and it worked.
Click to expand...
Click to collapse
Thanks Dan, that did the trick. I see the firmware update added quite a few watch faces but can't customize the colors on those until the Connect app is updated.
Waiting for the watchface contest winner to be released by Motorola!

Help! Note 8 shut down by itself when plugged in for fast charging.

I got this issue started in my Note 8 since June 2018
My Note 8 turns off automatically when I plug it for fast charging and shows that battery charging status. I tried powering it up but it keeps turning back off by itself.
Any ideas what might be the problem?
Thanks.
I have the same problem. The phone needs to cool down first. Put it in the freezer for 2 minutes and then try it again. If you're in the car then cool it with the AC vent. Crappy solution but it works for mine.
Jjavitable22 said:
I have the same problem. The phone needs to cool down first. Put it in the freezer for 2 minutes and then try it again. If you're in the car then cool it with the AC vent. Crappy solution but it works for mine.
Click to expand...
Click to collapse
I took the phone to Ubreakifx store and they told me that this is a charging port issue at first, then the next day they told me the motherboard is the problem because the phone didn't even pass the hardware diagnostic test. Therefore, phone replacement is necessary from Samsung due to this crappy factory defect.

Phone switched off overnight

I have recently purchased the A50 and love it. However, this morning I woke up late for work as my phone had switched off during its overnight charge. There was no way to turn it back on until at least 10 minutes after taking it off charge and frantically running to work. Once the phone was on, it had 100% battery.
Does anyone have any idea why this happened? Could it be an overheating issue?
This has never happened to any other phone I've owned.
I have been charging with the cable the A50 comes with but with the S7 plug. Could that be the culprit?
If that's the case I will just use the A50 plug itself.
I have looked everywhere for an answer. This only happened today and may never happen again but I would like to know other people's opinions.
Don't know why this happened,bug somewhere,software update,don't know,but do you really need to leave the phone on an overnight charge,
The treakle charge at 100% is known to cause heating issues, and I hear the a50 is not the most durable phone,.
Strange that it would just turn the phone off completely
manus31 said:
Don't know why this happened,bug somewhere,software update,don't know,but do you really need to leave the phone on an overnight charge,
The treakle charge at 100% is known to cause heating issues, and I hear the a50 is not the most durable phone,.
Strange that it would just turn the phone off completely
Click to expand...
Click to collapse
To be honest, it could have been as simple as electric fluctuation. I have no idea.
I didn't charge last night as I as slightly reluctant to do so.
So far, the phone is working flawlessly and hasn't restarted or shut off on its own. I will eventually charge it once the power drops to almost 0.
Will update so as to let everyone know in case there are similar issues out there.
daveydoo said:
To be honest, it could have been as simple as electric fluctuation. I have no idea.
I didn't charge last night as I as slightly reluctant to do so.
So far, the phone is working flawlessly and hasn't restarted or shut off on its own. I will eventually charge it once the power drops to almost 0.
Will update so as to let everyone know in case there are similar issues out there.
Click to expand...
Click to collapse
sounds like a bad battery in the phone, you should return it. i left it for overnight charging(forgot to remove it) and nothing happened.
kkarakk said:
sounds like a bad battery in the phone, you should return it. i left it for overnight charging(forgot to remove it) and nothing happened.
Click to expand...
Click to collapse
When it happened to me it was the second time I had charged over night, the first time was fine.
I haven't done it since and so far the phone has been fine.
During Update my phone A50, I just press Power button+Vol down button together. After that my phone was off and can not on till now. I tried to press vol up + power button together but it did not work. Can you please Help.
My Samsung A50 just went off by itself after power went off and has refused to come up. Truth is i have charged it several times using this same power and i can tell power is almost stable except that i am using a different charger head to charge for some time now. Wont sill come up, any help or suggestion?
We have several of these A50's and up to now we had 3 of them with this problem.
At the moment that it refuses to turn back on i noticed that the back of the phone is warm , between the top of the phone and the word SAMSUNG . The rest of the phone is cold.
I left the phone alone for about 4 hours without power cable plugged in , after those 4 hours i plugged it in and after a minute it started charging with a indicator of 0% .
You can also try a forced reboot ( hold volume up and down + power button for 5 sec )
Did anyone manage to solve this issue? My girlfriend's A50 has shut down twice overnight now, and the only way to turn it on is by pressing power and volume down for 10 seconds. She has the May update.
Same issue here, i reset my phone to factory settings then install all of my applications and since do that, the issue doesn't occurs any more till now (1 week)
Same here!
Same situation here!
It turned off during the night 3 times now!!
I was late to work The first time, now I have to activate the alarm on my wife's phone, because I don't trust this one anymore.
To turn it back on, you don't need to wait 4 hours, you just have to press power and volume down.
Samsung has to do something about this!
manssons said:
Did anyone manage to solve this issue? My girlfriend's A50 has shut down twice overnight now, and the only way to turn it on is by pressing power and volume down for 10 seconds. She has the May update.
Click to expand...
Click to collapse
That doesn't sound like it's actually turning off. More like it gets stuck with screen off and you're making a forced reboot with the button combination.
tys0n said:
That doesn't sound like it's actually turning off. More like it gets stuck with screen off and you're making a forced reboot with the button combination.
Click to expand...
Click to collapse
Yeah that might actually be the case, and it's completely hung since alarms won't go off. Apparently it does not seem like an isolated case so I guess we'll see what the store says.
Same situation at my A50 to. No notifications,no reaction, no alarm, no reacttion after simple power button press,only black display. It get alive only with described buttons combination-power+vol up .
The problem occure only after night charging time, in the morning.
I was advised not to leave on charge overnight. I have just got this phone and was asking live chat about something else and she mentioned new smart phones did not require full overnight charges and unplug as soon as it’s finished charging.. also that fully discharging battery to 0% is not recommended either and should be charged around 20% to increase the life of the battery. I think I will try that advice. Always had Samsung phones and been happy with my S5 for many years..but it’s very outdated and decided on upgrade but can’t justify the price of S10 lol.

Categories

Resources