Hi all,
I was running on Fulmics 7.6 for close to a year now, and since it was my backup phone, it was usually on Wi-Fi. But I was able to use my Cricket SIM card before, until yesterday. I got a new SIM card from US Mobile, popped it in, and to my surprise: no data. I got the "No Service" message at the bottom of the notification drawer, and it said "Service disabled" at the top of the lock screen. When I try to update the APN, the "Mobile Networks" option is greyed out. I updated to Fulmics 8.0 and that didn't seem to work. I tried flashing Xceed kernel since some posts said a new kernel would help, and that didn't work. I wiped everything in TWRP, and reflashed, and that didn't work.
I was able to get data to work for a few minutes, when someone suggested using paper on top of the SIM card. After I restarted the phone... data did not work again. Then this morning, I updated Magisk from 13.3 (I think that's what was in Fulmics 8.0) to 15.7, and that got data to work again... but when I updated Magisk Manager to 5.7, data stopped working.
I've since tried clean installing Fulmics 8.0, updating Magisk but not the Manager, and even unrooted my phone and rerooted it. Still no dice. I'm drawing blanks here. The phone clearly detects the SIM, but it insists on not receiving data for some reason. I tried this with 2 different SIM cards that work in my other phones, so I'm not sure what the issue is here.
Probably, simcard slot is broken. Mine LG G3 MB got warranty change, because that problem was same like on yours phone
have you tried without simcard and did you see no serivce or no sim inserted?
pjadec said:
Probably, simcard slot is broken. Mine LG G3 MB got warranty change, because that problem was same like on yours phone
Click to expand...
Click to collapse
Yeah, I think that may be the case
barron9 said:
have you tried without simcard and did you see no serivce or no sim inserted?
Click to expand...
Click to collapse
If the SIM card is in, it says "service disabled". Without the SIM card, it says "No SIM inserted"
Related
hey,
my android was getting a bit slow, so i restarted my phone.
after that the phone said sim not found.
i tried everything, restarting a few times, locking bootloader and i even flashed my rom back to full stock.
but still no success.
what do i need to do?
thanks in advance
Denniz0229 said:
hey,
my android was getting a bit slow, so i restarted my phone.
after that the phone said sim not found.
i tried everything, restarting a few times, locking bootloader and i even flashed my rom back to full stock.
but still no success.
what do i need to do?
thanks in advance
Click to expand...
Click to collapse
Maybe bad connection on your sim card?
Try removing the SIM card and put it back in, and then boot the phone.
Sent from my Galaxy Nexus using Tapatalk
done that, doesn't help
Im getting hte same issue. The 4.0.2 update came through, rebooted the phone. SIM not found, press to reboot....
Rebooted, SIM still not working. remove SIM and replace. Still not working. replaced with another SIM. Still not working.
Was working fine prior to the 4.0.2 update. This is on a 1 month old phone that has never been rooted. It is still as stock as it comes out of the box... And i want to test it more before i start boxing it up to send it back...
Have you tried leaving the battery out for a bit, then trying powering it up again?
Here is where it gets weird. I tried 2 other sim cards as well as my own. none of them worked. put my sim card back in and tried again, still not working. turned it off over night. went to Vodafone and asked if i could try a new SIM in the phone. still not working. put my TPG/Optus sim in and it started working. got a new SIM from Voda, transfered all the account info to the new card, waited an hour and tried it again and now it works :/
Dont know what caused it to stop working and dont know what caused it to start working again :/ im going to throw the word "Vodafone" in there as the cause because people will just nod their head and say... "yep, that was probably it..."
I have the same issue with AT&T....the phone does recognize the SIM, APN and all...but no signal. Just once in a while it gets registered on teh network, but for one minute or so...I don't know what to do
Same issue here, after a reboot my phone does not recognize my sim at all. no signal at all. tried a different sim, nothing, bought a new sim but nothing again, returned to stock, everything, but still nothing....no remedy yet....
My phone is not detecting SIM card. It all happened suddenly. Phone was working till a minute before. Suddenly got a notification
NO SIM CARD EMERGENCY CALLS ONLY
I did factory reset, Went back to stock OS from VANIR ROM
Even got a new SIM card. Nothing seems to be working.
Please help me in fixing this.
preythap said:
My phone is not detecting SIM card. It all happened suddenly. Phone was working till a minute before. Suddenly got a notification
NO SIM CARD EMERGENCY CALLS ONLY
I did factory reset, Went back to stock OS from VANIR ROM
Even got a new SIM card. Nothing seems to be working.
Please help me in fixing this.
Click to expand...
Click to collapse
1. Try changing radio.
2. Get a new phone. It seems to me that something broke in hardware.
FredFS456 said:
1. Try changing radio.
2. Get a new phone. It seems to me that something broke in hardware.
Click to expand...
Click to collapse
Thanks for the reply
what do you mean by change radio???
hi
I have a very annoying problem whit the sim slot 1 (i currently test the slot 2)
Very often, the phone tell me "Sim card not detected", and i have to open the phone, dismount the card and put in again.. until the next time.. like i said, it's occurs very often, 10-15 a day..
Even when the phone is on the table without touching it..
I have rooting it and thats it.. 2.19.40.22
I would like to know if someone have similar problems before i try to reflash whit older stock rom??!
It happened to me briefly- After flashing my first full back -up back to the fone --then i did a factory reset and this fixed the sim slot problem
timbernot said:
It happened to me briefly- After flashing my first full back -up back to the fone --then i did a factory reset and this fixed the sim slot problem
Click to expand...
Click to collapse
Hi, I think i have the same problem after testing the Cyanogen build for ZE551ML. Have you did a factory reset from recovery (wipe data, cache and dalvik) or a full stock rom flash ?
Thanks
Above, I was referring to the full 5gb asus ROM back up I made immediately after unlocking bootloader installing twrp and rooting, I installed svn ROM and backed that up too..stripped svn ROM further..backed that up too. Then went about trying my Asus full original...sim 2 was only detected..so did a factory reset and sim came back.
To get sim recognised in CM,I had to wipe usual..install..set up...and factory reset it...hope that clears it up a bit lol
timbernot said:
Above, I was referring to the full 5gb asus ROM back up I made immediately after unlocking bootloader installing twrp and rooting, I installed svn ROM and backed that up too..stripped svn ROM further..backed that up too. Then went about trying my Asus full original...sim 2 was only detected..so did a factory reset and sim came back.
To get sim recognised in CM,I had to wipe usual..install..set up...and factory reset it...hope that clears it up a bit lol
Click to expand...
Click to collapse
Thanks, I'll try !
DmA81 said:
Thanks, I'll try !
Click to expand...
Click to collapse
Oh,try a reboot after factory reset..I forgot to put in description above
Guys can you check your sim holder lock . I mean when you put the sim in holder check if it is properly fitted. Issue is some SIM cards are thinner than normal and sim holder unable to grip it. I faced same issue.
Also recommend using ASUS ZenUI app called ASUS Support. There are several helpful tips with basic troubleshooting techniques for your device including including SIM card troubleshooting. Please go to Apps/ASUS Support/Assistance/SIM Card/Sim card not detected
Sincerely
ASUS_USA
Sim Card not detected
Hey guys,
I am having a similar issue. I have 2 Sims, AT&T and GCI (local carrier). AT&T Sim works in both Slot 1 & 2, and GCI Sim works in slot 2 only. The AT&T sim is a standard MicroSim and the GCI sim is a Tri-Cut sim, so basically a NanoSim in a Micro Adapter.
Sometimes when the GCI Sim is in slot 1, it will recognize for a couple seconds then go gray..
timbernot said:
Above, I was referring to the full 5gb asus ROM back up I made immediately after unlocking bootloader installing twrp and rooting, I installed svn ROM and backed that up too..stripped svn ROM further..backed that up too. Then went about trying my Asus full original...sim 2 was only detected..so did a factory reset and sim came back.
To get sim recognised in CM,I had to wipe usual..install..set up...and factory reset it...hope that clears it up a bit lol
Click to expand...
Click to collapse
timbernot said:
It happened to me briefly- After flashing my first full back -up back to the fone --then i did a factory reset and this fixed the sim slot problem
Click to expand...
Click to collapse
This **** happened to me too
I wonder whats wrong with our backup and twrp
GCI (Dillingham, Alaska)
I to am having the same issue. By chance did you solve the issue? I love my Zenfone 2, but am frustrated by not being able to use 3G. I've tried a few differant methods to fix it. No luck yet.
Please if you have a fix let me know. reply here, or email me at bupbup777 at gmail.
I really hope someone knows a fix.
jmillsak said:
Hey guys,
I am having a similar issue. I have 2 Sims, AT&T and GCI (local carrier). AT&T Sim works in both Slot 1 & 2, and GCI Sim works in slot 2 only. The AT&T sim is a standard MicroSim and the GCI sim is a Tri-Cut sim, so basically a NanoSim in a Micro Adapter.
Sometimes when the GCI Sim is in slot 1, it will recognize for a couple seconds then go gray..
Click to expand...
Click to collapse
I subscribe to the "theory" that some SIM cards are thinner than others and they drop out of slot 1.
In fact, I have 3 SIM cards and they range in thickness by around 0.5mm according to my cheap chinese mircometer. I don't believe that it is coincidence that the thinner ones lose SIM detection more than the thicker ones.
Also it is no coincidence that slot 2 doesn't lose detection becuase the SIMs don't slide upwards out of slot 2, but they do slide downwards out of slot 1.
Do this experiment: Put a SIM in each slot, now place a 3rd SIM in the space between the two. You will notice that it sits easily in the gap between the two installed SIMs with a bit of free play. Put the back cover back on and use the phone normally for a while (a day or two). Now take off the phone back and tip the phone over, does the "third" SIM fall on the floor, or has it been gripped by the SIM in slot 1 as it has gradually slid out of its slot?
Since I put one layer of sellotape on the back of all my SIMs, I have not had one single "SIM not installed" message. I used to get them all the time, especially with one of the thinner SIMs in slot 1 and above all when using the phone in the car (the fully vertical position and the vibrations seemed to have accelerated the SIM slipping out of its slot).
By the way, I never had the SIM slide completely out, but they certainly are not gripped sufficiently in place and slip enough to disconnect.
I had same "sim card 1 not detected" issue.
It worked back when i did soft reboot,.
And no more issue after factory reset
Re @ leftrand earlier on page 1.....
Sorry not been here in a while , but I think this was related to an earlier twrp we used , fixed with the later one I think. So it was a matter of restoring full original bk up,then factory reset then set up again and do another bk up. Keeping original bk up just in case . That was a while back now and should be fixed
facing same problem... only after updating ota. always.. sim 1 is not detected...
Leftrand said:
This **** happened to me too
I wonder whats wrong with our backup and twrp
Click to expand...
Click to collapse
That no way to have a sim 1 working thru TWRP back up after flashing the CM13. What I did was doing a clean flash with SuperZen - 2.20.40.156 Full.
The problem was solve. then I flash back my back up TWRP. The phone now work like a charm.
dominicong123 said:
That no way to have a sim 1 working thru TWRP back up after flashing the CM13. What I did was doing a clean flash with SuperZen - 2.20.40.156 Full.
The problem was solve. then I flash back my back up TWRP. The phone now work like a charm.
Click to expand...
Click to collapse
Yes clean flash solve proublem but dont you tired installing app and losing data ?
I know we have TB.
But recently i use unthetered twrp by TheSSJ and everything goes fine backup and restore no issue with simcard
bupbup777 said:
I to am having the same issue. By chance did you solve the issue? I love my Zenfone 2, but am frustrated by not being able to use 3G. I've tried a few differant methods to fix it. No luck yet.
Please if you have a fix let me know. reply here, or email me at bupbup777 at gmail.
I really hope someone knows a fix.
Click to expand...
Click to collapse
I got it fixed bro! the phone does not like the Nano sim cards in the adapter. I happend to find an old GCI micro sim and had them activate it. works great now.
ok i found a solution. i read a earlier reply saying you cannot assess sim 1 whilst using a recovery back up flashed. i was currently using cm13 nightlys and this morning i flashed paranoid 5.1 or so.... i wanted to go back and compare the two but what i did was restore it from a backup.... so what you should do is when wanting to change roms, KEEP THE ZIP FILES THAT YOU USE TO FLASH THE ROMS WITH!!!!!!!!!!!! im still asking you to back up roms (preferably system before you flash) just so you dont hard brick it.
bottom line is back up rom, but keep zip files for when you want to change between roms. hope i can help
I have this problem, compounded by the fact that it seems all Android 6.0 (or possibly all CM based ROMs for the ZenFone?) have an issue where losing cell signal in a dead zone permanently breaks the radio until the device is rebooted. Even if the SIM is recognized, after going through a no signal area, the signal never gets acquired again and the SIM information lines remain blank or unknown. Trying to refresh the networks or providers list throws an error toast.
My previous LS990 worked charm with GSM networks. But recently purchased LS990 shows signal for like first minutes, then shows "Insert valid sim and reboot" message. hen reboots itself. after that sim is not recognised. The sim works fine on other phones. and tried many sims on this LS990, all failed.
Flashed KK, LP, MM stock with GSM unlock files, Fulmics rom, cloudy and AOSP. Fulmics seems to cath signals bit longer than other OSs, but it fails too.
Is this related to some hardware issue? but the thing is phone catches GSM signals flawlessly before above mentioned "Invalid sim" message. after that No sim is detectable.
Can anyone help me to fix it please? I would do a help to help. Donation :highfive:
GTRanushka said:
My previous LS990 worked charm with GSM networks. But recently purchased LS990 shows signal for like first minutes, then shows "Insert valid sim and reboot" message. hen reboots itself. after that sim is not recognised. The sim works fine on other phones. and tried many sims on this LS990, all failed.
Flashed KK, LP, MM stock with GSM unlock files, Fulmics rom, cloudy and AOSP. Fulmics seems to cath signals bit longer than other OSs, but it fails too.
Is this related to some hardware issue? but the thing is phone catches GSM signals flawlessly before above mentioned "Invalid sim" message. after that No sim is detectable.
Can anyone help me to fix it please? I would do a help to help. Donation :highfive:
Click to expand...
Click to collapse
You can try to flash modem only. Once i messed up some settings on the phone trying to unlock LTE bands and after that my signal was coming and going whole time, but no "Insert valid sim" message appeared. just on off. I have flashed ZVC modem from recovery and it worked fine. make backup of everything just in case and flash it.
idinaxui said:
You can try to flash modem only. Once i messed up some settings on the phone trying to unlock LTE bands and after that my signal was coming and going whole time, but no "Insert valid sim" message appeared. just on off. I have flashed ZVC modem from recovery and it worked fine. make backup of everything just in case and flash it.
Click to expand...
Click to collapse
I tried. But no luck. Thanks for help though
anyone?
Man i have the same problem I've tried everythings and nothing works i guess if we try to unlock with box will be fixed
racav1904 said:
Man i have the same problem I've tried everythings and nothing works i guess if we try to unlock with box will be fixed
Click to expand...
Click to collapse
Same here bro. Gonna try the box method on this 15th. Will update you about results.
Hello Everyone,
I need some help regarding the network issues for Moto Z Play.
I started this thread because after doing a lot of solutions, resets and still it wasn't successful.
So here's the story -
Two days ago my brother gave me the phone which was in excellent condition (VoLTE working, Battery Performance, etc.) working on Android 7.0.
Then he did a reset on the phone from Settings so I can use it.
When I inserted my SIM Cards in the phone, I got network and everything and immediately I received an Update for Nougat 7.1.1. I installed the update and then when the phone booted, I did the setup and everything. But l wasn't able to get VoLTE on my phone. There was no Enhanced LTE Mode option in Settings. I thought it was something temporary and maybe after sometime I will be automatically resolved but it didn't.
The next day I started researching over the internet and found clearing the cache or data of settings or hard reset from recovery/settings will do and I did it but none of the solutions worked. Then I thought it was the SIM problem but it wasn't. I inserted the same Jio SIM from my phone into another VoLTE phone and it was working. I also tried another Jio SIM in Moto and it was showing VoLTE and everything was working perfect. Also I inserted my idea SIM (which was in SIM2 slot) in SIM 1 and it was not showing even 4G range (Just 3G) (The idea SIM is also 4G).
I tried everything - Swapping SIM cards, resetting the phone, Clearing cache, etc. I don't know why this has happened as my brother was using the same carrier sim in same slots (SIM1 - Jio|SIM2- Idea).
I also called the JIO care and they took the complaint and they told me they would look forward to it in 48 hours.
Also, my bootloader is locked and can I flash original stock firmware? (I guess that's only thing left I haven't tried) If so, please provide the link and guide to flash the firmware.
If Anyone has a solution please help me, I am in big trouble.
Get a new sim card for your number. Don't ask why. But this will work, trust me.
samarth05 said:
Hello Everyone,
I need some help regarding the network issues for Moto Z Play.
I started this thread because after doing a lot of solutions, resets and still it wasn't successful.
So here's the story -
Two days ago my brother gave me the phone which was in excellent condition (VoLTE working, Battery Performance, etc.) working on Android 7.0.
Then he did a reset on the phone from Settings so I can use it.
When I inserted my SIM Cards in the phone, I got network and everything and immediately I received an Update for Nougat 7.1.1. I installed the update and then when the phone booted, I did the setup and everything. But l wasn't able to get VoLTE on my phone. There was no Enhanced LTE Mode option in Settings. I thought it was something temporary and maybe after sometime I will be automatically resolved but it didn't.
The next day I started researching over the internet and found clearing the cache or data of settings or hard reset from recovery/settings will do and I did it but none of the solutions worked. Then I thought it was the SIM problem but it wasn't. I inserted the same Jio SIM from my phone into another VoLTE phone and it was working. I also tried another Jio SIM in Moto and it was showing VoLTE and everything was working perfect. Also I inserted my idea SIM (which was in SIM2 slot) in SIM 1 and it was not showing even 4G range (Just 3G) (The idea SIM is also 4G).
I tried everything - Swapping SIM cards, resetting the phone, Clearing cache, etc. I don't know why this has happened as my brother was using the same carrier sim in same slots (SIM1 - Jio|SIM2- Idea).
I also called the JIO care and they took the complaint and they told me they would look forward to it in 48 hours.
Also, my bootloader is locked and can I flash original stock firmware? (I guess that's only thing left I haven't tried) If so, please provide the link and guide to flash the firmware.
If Anyone has a solution please help me, I am in big trouble.
Click to expand...
Click to collapse
devilvj said:
Get a new sim card for your number. Don't ask why. But this will work, trust me.
Click to expand...
Click to collapse
Thanks man, I was too thinking of that and went to JIO store. They had a server error and will be back available in 4-5 days. Will then post with new SIM results.