Related
Hi all , today I've flash the stock rom for my Note 2 , but after that , my Note 2 cannot registered on the network and the IMEI was change to 0049xxx...
Then I've flash the new Modem here as this guy told http://forum.xda-developers.com/showpost.php?p=43037352&postcount=134.
But in Odin , I choose the file in PDA tab instead of Phone Tab and the modem can still flash ok. After that ,when reboot my phone , it cannot turn off every time the screen is off. And I can't make my phone become normal , i've reflash the stock rom many times , but that didn't help.
Someone please help me?
And I cannot connect to KIES anymore ...
heorung said:
And I cannot connect to KIES anymore ...
Click to expand...
Click to collapse
hey. try flashing the rom again using odin and set it as PDA..
after that, lei it boot.. if you still not getting any signal, or lost ypur imei, flash the modem and set it as PHONE
Hope it works
among4239bulan said:
hey. try flashing the rom again using odin and set it as PDA..
after that, lei it boot.. if you still not getting any signal, or lost ypur imei, flash the modem and set it as PHONE
Hope it works
Click to expand...
Click to collapse
Hi , thanks for the reply , did you mean flash the firmware file with the PHONE option tick?
heorung said:
Hi , thanks for the reply , but how to set pda or phone?
Click to expand...
Click to collapse
see image below..
the red circle is PDA, insert your ROM file here.
the pink circle is PHONE, insert your MODEM file here.
also wipe cache, data and dalvik cache in cwm.
among4239bulan said:
see image below..
the red circle is PDA, insert your ROM file here.
the pink circle is PHONE, insert your MODEM file here.
also wipe cache, data and dalvik cache in cwm.
Click to expand...
Click to collapse
Hi among4239bulan , i already tried that but the phone still mess up , i've tried to flash the newwest stock rom and the network has return back to normal , but the phone cannot turn on whenever the screen is off
Don't know if put the modem.tar.md5 in the "PDA" slot is destroyed anything ?
I download the rescue firmware but Odin cannot flash it , it's always stuck at
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
heorung said:
Hi among4239bulan , i already tried that but the phone still mess up , i've tried to flash the newwest stock rom and the network has return back to normal , but the phone cannot turn on whenever the screen is off
Don't know if put the modem.tar.md5 in the "PDA" slot is destroyed anything ?
I download the rescue firmware but Odin cannot flash it , it's always stuck at
Click to expand...
Click to collapse
it may be related to the wrongly placed modem.tar earlier.. just try flashing another rom,custom one just to see whether the problem still persist.. or have you tried the pre-rooted stock rom that dr.ketan had provided?
Hi among4239bulan , i used the Mobile Odin to flash the rescue firmware , and seems that the problem was gone. Thanks for your help , I really appreciate that ^^
heorung said:
Hi among4239bulan , i used the Mobile Odin to flash the rescue firmware , and seems that the problem was gone. Thanks for your help , I really appreciate that ^^
Click to expand...
Click to collapse
no problem, glad that the problem is solved.
Hi,
I have upgraded my grand to Cosmic ROM using below link.
http://forum.xda-developers.com/showthread.php?t=2627818 and http://www.yogeshsarkar.com/blog/2014/04/01/how-to-install-custom-rom-on-galaxy-grand-duos/
I was having official 4.2.2 before upgrade and upgraded to Consmic ROM v4.3
after successfull upgrade, i have restarted my phone. It is struct in logo screen only.
Please help to solve this issue.
Thanks
rsvali said:
Hi,
I have upgraded my grand to Cosmic ROM using below link.
http://forum.xda-developers.com/showthread.php?t=2627818 and http://www.yogeshsarkar.com/blog/2014/04/01/how-to-install-custom-rom-on-galaxy-grand-duos/
I was having official 4.2.2 before upgrade and upgraded to Consmic ROM v4.3
after successfull upgrade, i have restarted my phone. It is struct in logo screen only.
Please help to solve this issue.
Thanks
Click to expand...
Click to collapse
U should only follow the instructions given in the op and not on a tech blog
U can try this
Go to recovery
Wipe data
Flash rom zip
Reboot
doctor_droid said:
U should only follow the instructions given in the op and not on a tech blog
U can try this
Go to recovery
Wipe data
Flash rom zip
Reboot
Click to expand...
Click to collapse
Thanks for the reply.
Now i tried to recover using Odin3 v3.09, i got below logs.
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
It is showing RESET! instead of PASS.
what is the difference between them, how can i get PASS.
Thanks in advance.
rsvali said:
Thanks for the reply.
Now i tried to recover using Odin3 v3.09, i got below logs.
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
It is showing RESET! instead of PASS.
what is the difference between them, how can i get PASS.
Thanks in advance.
Click to expand...
Click to collapse
Its okay if the procedure was completed...reset will change to pass by itself... After some time
If u experiencing a bootloop still
Boot into stock recovery
Wipe data(this will delete everything on internal memory including pics videos ... Etc
One workaround to save data is
Flash a custom recovery after odin flash..
Go into custom recovery
Wipe data from there.. Bingo
doctor_droid said:
Its okay if the procedure was completed...reset will change to pass by itself... After some time
If u experiencing a bootloop still
Boot into stock recovery
Wipe data(this will delete everything on internal memory including pics videos ... Etc
One workaround to save data is
Flash a custom recovery after odin flash..
Go into custom recovery
Wipe data from there.. Bingo
Click to expand...
Click to collapse
Should i need to wipe the data before installing ROM from ZIP or after installing from ZIP or both. Please let me know.
Sorry for too many questions.
Can you please share any details step by step documentation to do this. thanks for your help.
rsvali said:
Should i need to wipe the data before installing ROM from ZIP or after installing from ZIP or both. Please let me know.
Sorry for too many questions.
Can you please share any details step by step documentation to do this. thanks for your help.
Click to expand...
Click to collapse
Hello...
Its better to wipe data before and after ROM installation that's the procedure i follow and till now No bootloops i had..
and with this Follow the instruction given in ROM OP too for successful Installation of ROM...
jackeagle said:
Hello...
Its better to wipe data before and after ROM installation that's the procedure i follow and till now No bootloops i had..
and with this Follow the instruction given in ROM OP too for successful Installation of ROM...
Click to expand...
Click to collapse
I have followed same proceudre, but still my phone is struck in logo only.
the only difference is, odin showed RESET and i have unplugged the device and started device in factory mode ( using power+home+volume up). After few minutes of unplug odin shows PASS.
I have wipe the data and cache before and after the ROM installation.
Please let me know if any mistake is there, and do let me know how to make my device work.
Thanks in advance.
rsvali said:
I have followed same proceudre, but still my phone is struck in logo only.
the only difference is, odin showed RESET and i have unplugged the device and started device in factory mode ( using power+home+volume up). After few minutes of unplug odin shows PASS.
I have wipe the data and cache before and after the ROM installation.
Please let me know if any mistake is there, and do let me know how to make my device work.
Thanks in advance.
Click to expand...
Click to collapse
Which Recovery you are using now?? CWM or Philz? Which ROM you installed??
jackeagle said:
Which Recovery you are using now?? CWM or Philz? Which ROM you installed??
Click to expand...
Click to collapse
I am using ClockworkMod recovery with SELinux support and Cosmic CM 11 ROM for Galaxy Grand Duos.
rsvali said:
I am using ClockworkMod recovery with SELinux support and Cosmic CM 11 ROM for Galaxy Grand Duos.
Click to expand...
Click to collapse
If you are using Cosmic CM then you have to flash Evolution kernel 1.7.6 son after you flash Cosmic ROM otherwise it will cause bootloop...
Hope this helps you..
jackeagle said:
If you are using Cosmic CM then you have to flash Evolution kernel 1.7.6 son after you flash Cosmic ROM otherwise it will cause bootloop...
Hope this helps you..
Click to expand...
Click to collapse
How to flash Evolution kernel 1.7.6, can you please share link/video/thread with step by step information. that would be help full.
rsvali said:
How to flash Evolution kernel 1.7.6, can you please share link/video/thread with step by step information. that would be help full.
Click to expand...
Click to collapse
You can see here http://forum.xda-developers.com/showthread.php?t=2627818
download Evolution Kernel 1.7.6 and after flashing ROM flash this Kernal like you flash ROM and then wipe cache,Dalvic,Wipe Data and good to go... Remember Always Follow has given in OP each and every step that too while flashing kernel and if you are not familiar with F2fs don't install it just flash ROM and KERNEL... and gapps too..
jackeagle said:
You can see here http://forum.xda-developers.com/showthread.php?t=2627818
download Evolution Kernel 1.7.6 and after flashing ROM flash this Kernal like you flash ROM and then wipe cache,Dalvic,Wipe Data and good to go... Remember Always Follow has given in OP each and every step that too while flashing kernel and if you are not familiar with F2fs don't install it just flash ROM and KERNEL... and gapps too..
Click to expand...
Click to collapse
Thanks it worked..
rsvali said:
Thanks it worked..
Click to expand...
Click to collapse
Congrats... Enjoy...:good::good:
Hello Please if possible be very Noob friendly with your instructions, thanks
Ok I have a rooted Samsung Galaxy S3 AT&T on Firmware 4.3
So I noticed the 4.4.2 Update came out and i really want to update to it but I couldn't OTA because it would say update failed later discovered this is because my S3 is rooted
Now I am in the middle of trying to unroot my galaxy s3 and am very confused i tried doing backup and reset obviously that didnt work i am very confused on how this Odin software works so if you someone could give me very noob specific directions it would be greatly appreciated!
Thanks in Advance
Just open the SuperSU app and select Full Unroot. Let it do its thing and you're unrooted.
Or follow enewman17's thread for how to update.
I believe unrooting will only be successful if none of the AT&T apps were removed from the device. I forgot about that point and I had to flash the 4.3 stock image in order to successfully install the OTA update to 4.4.2. The OTA will try to patch all that ATT bloat during installation; if its not there it will fail.
DocHoliday77 said:
Just open the SuperSU app and select Full Unroot. Let it do its thing and you're unrooted.
Or follow enewman17's thread for how to update.
Click to expand...
Click to collapse
Yah i already did that but it would still fail the update at 24%
mwrobe1 said:
I believe unrooting will only be successful if none of the AT&T apps were removed from the device. I forgot about that point and I had to flash the 4.3 stock image in order to successfully install the OTA update to 4.4.2. The OTA will try to patch all that ATT bloat during installation; if its not there it will fail.
Click to expand...
Click to collapse
Could you please give me a download link or something to the 4.3 stock image for odin?
Everytime i download one it always some weird files that i do not know how to utilize through odin
So if you could give me a stock 4.3 that would be great thanks
nkhaira said:
Could you please give me a download link or something to the 4.3 stock image for odin?
Everytime i download one it always some weird files that i do not know how to utilize through odin
So if you could give me a stock 4.3 that would be great thanks
Click to expand...
Click to collapse
I used this method in post #1 to go back to stock 4.3: http://forum.xda-developers.com/showthread.php?t=2565972
Contrary to other posts...I only had Auto Reboot checked and that worked for me.
This will also wipe all data from your device...make sure you backup pics/vids/contacts/etc. before you do this.
After you take the OTA update, I can also confirm that TowelRoot will successfully root the ATT GS3 running KitKat. Although the documentation says no reboot is required...I needed a reboot after rooting with towelroot.
mwrobe1 said:
I used this method in post #1 to go back to stock 4.3: http://forum.xda-developers.com/showthread.php?t=2565972
Contrary to other posts...I only had Auto Reboot checked and that worked for me.
This will also wipe all data from your device...make sure you backup pics/vids/contacts/etc. before you do this.
After you take the OTA update, I can also confirm that TowelRoot will successfully root the ATT GS3 running KitKat. Although the documentation says no reboot is required...I needed a reboot after rooting with towelroot.
Click to expand...
Click to collapse
But isnt that for the Sprint Galaxy s3
I have the SGH-i747 AT&T LTE USA Version?
nkhaira said:
But isnt that for the Sprint Galaxy s3
I have the SGH-i747 AT&T LTE USA Version?
Click to expand...
Click to collapse
My sincerest apologies. Correct. I used that link for you because the instructions were clear and concise. The firmware download should be good from here: http://stockroms.net/file/GalaxyS3/SGH-I747/StockROMS.net-SGH-I747_ATT_1_20120522193451.zip
mwrobe1 said:
My sincerest apologies. Correct. I used that link for you because the instructions were clear and concise. The firmware download should be good from here: http://stockroms.net/file/GalaxyS3/SGH-I747/StockROMS.net-SGH-I747_ATT_1_20120522193451.zip
Click to expand...
Click to collapse
Just to make sure this is the file i put in odin so i can go back to stock 4.3 update (non rooted) and update OTA to 4.4.2 right?
nkhaira said:
Just to make sure this is the file i put in odin so i can go back to stock 4.3 update (non rooted) and update OTA to 4.4.2 right?
Click to expand...
Click to collapse
Correct...make sure you put your phone in download mode as well (Hold down Volume Down, Center Home, and Power buttons together for about 10 seconds...When your screen turns off, let go of the Power button but keep holding down Volume Down and Center Home buttons....When you see the warning screen, hit Volume Up button...Connect a microUSB cable from your phone to computer...Run Odin...click on “PDA”, then choose the file you downloaded...click on Start once Odin "loads" the file...wait 10-15 minutes for the flash too occur...after coming back from a reboot you should be on stock 4.3)
mwrobe1 said:
Correct...make sure you put your phone in download mode as well (Hold down Volume Down, Center Home, and Power buttons together for about 10 seconds...When your screen turns off, let go of the Power button but keep holding down Volume Down and Center Home buttons....When you see the warning screen, hit Volume Up button...Connect a microUSB cable from your phone to computer...Run Odin...click on “PDA”, then choose the file you downloaded...click on Start once Odin "loads" the file...wait 10-15 minutes for the flash too occur...after coming back from a reboot you should be on stock 4.3)
Click to expand...
Click to collapse
Thank you for being responsive and helpful
I have started the file download i have slow internet speed at my house but it should download in 30 minutes and in a hour i will update this thread if it worked thanks!
mwrobe1 said:
Correct...make sure you put your phone in download mode as well (Hold down Volume Down, Center Home, and Power buttons together for about 10 seconds...When your screen turns off, let go of the Power button but keep holding down Volume Down and Center Home buttons....When you see the warning screen, hit Volume Up button...Connect a microUSB cable from your phone to computer...Run Odin...click on “PDA”, then choose the file you downloaded...click on Start once Odin "loads" the file...wait 10-15 minutes for the flash too occur...after coming back from a reboot you should be on stock 4.3)
Click to expand...
Click to collapse
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
That is the error message i am getting.. when i am trying this
nkhaira said:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
That is the error message i am getting.. when i am trying this
Click to expand...
Click to collapse
I'll try to locate the exact MD5 I used and give you a link later today/this week. Sorry for the trouble.
mwrobe1 said:
I'll try to locate the exact MD5 I used and give you a link later today/this week. Sorry for the trouble.
Click to expand...
Click to collapse
Ok As soon as possible would be appreciated currently this is my only phone and i need to use it and I factory reset it yesterday thinking it would get rid of the root i would like to install all my apps and everything as soon as possible thanks
Your Odin flash failed because you tried to flash a much older firmware. LEM. You need to flash the 4.3 firmware. You can use this thread. http://forum.xda-developers.com/showthread.php?t=2722660
Enewman17 has one too I think. Not sure where exactly right now though.
DocHoliday77 said:
Your Odin flash failed because you tried to flash a much older firmware. LEM. You need to flash the 4.3 firmware. You can use this thread. http://forum.xda-developers.com/showthread.php?t=2722660
Enewman17 has one too I think. Not sure where exactly right now though.
Click to expand...
Click to collapse
Thanks for your reply So since this in too many different files what do i do to combine them (noob)? i know its something to the extent of extracting them into one folder?
Could you give me instructions on that
DocHoliday77 said:
Your Odin flash failed because you tried to flash a much older firmware. LEM. You need to flash the 4.3 firmware. You can use this thread. http://forum.xda-developers.com/showthread.php?t=2722660
Enewman17 has one too I think. Not sure where exactly right now though.
Click to expand...
Click to collapse
Ok i got all the files combined now i see a csc a AP file and alot of the file catergories from Odin do i only need the AP file for PDA or do i need to insert each corresponding file into each corresponding category in Odin?
I don't have this device so its apparently a little different than I'm used to in this regard. Check post 13 of that thread to see if that helps. Otherwise someone more familiar with that particular process will need to chime in.
DocHoliday77 said:
I don't have this device so its apparently a little different than I'm used to in this regard. Check post 13 of that thread to see if that helps. Otherwise someone more familiar with that particular process will need to chime in.
Click to expand...
Click to collapse
Thank You So much!!
Sorry for late reply but the download you sent me worked and after 10 minutes i was on stock 4.3 upgraded to 4.4.2 without any problems!!!
THANKS!!!
When I try to add my Gmail to sign in to the play store it says couldn't sign in there was a problem communicating with google play servers. I have found the correct google play services apk and reinstalled it. Still no luck. Anyone else have this problem?
HollowKyo said:
When I try to add my Gmail to sign in to the play store it says couldn't sign in there was a problem communicating with google play servers. I have found the correct google play services apk and reinstalled it. Still no luck. Anyone else have this problem?
Click to expand...
Click to collapse
I'm thinking about factory reset. Would I lose root and unlocked bootloader or brick possibly? But I've also seen factory reset doesn't help in most cases. I've fixed this before by downloading the correct apk on my note 2. And I'm 100 percent certain I have the right one this time. I've also cleared the caches and things. I'm a techy person. I've tried all the things.
Edit:
Actually I've been looking for a performance increasing rom without losing too many features. There's a lot I don't care about. Anyone know of a good one for this dev converted retail verizon one yet?
HollowKyo said:
I'm thinking about factory reset. Would I lose root and unlocked bootloader or brick possibly? But I've also seen factory reset doesn't help in most cases. I've fixed this before by downloading the correct apk on my note 2. And I'm 100 percent certain I have the right one this time. I've also cleared the caches and things. I'm a techy person. I've tried all the things.
Edit:
Actually I've been looking for a performance increasing rom without losing too many features. There's a lot I don't care about. Anyone know of a good one for this dev converted retail verizon one yet?
Click to expand...
Click to collapse
Are the date & time & timezone correct on your phone? Can you get to google.com from the phone's browser?
If the date & time settings are correct, try just uninstalling all updates and clearing data for Google Play Services, Google Play Store, and Google Services Framework. Make sure nothing Google related has been disabled or uninstalled.
Factory reset is safe, you won't lose dev status that way. Flashing factory firmware that contains an aboot.mbn will lose your dev status, and you'll have to go through the conversion again.
blindmanpb said:
Are the date & time & timezone correct on your phone? Can you get to google.com from the phone's browser?
If the date & time settings are correct, try just uninstalling all updates and clearing data for Google Play Services, Google Play Store, and Google Services Framework. Make sure nothing Google related has been disabled or uninstalled.
Factory reset is safe, you won't lose dev status that way. Flashing factory firmware that contains an aboot.mbn will lose your dev status, and you'll have to go through the conversion again.
Click to expand...
Click to collapse
The phone does connect to the internet. I've done all the things in the list aside from factory reset. Would you retain root? And nothing google has been disabled.
If you can retain root after a reboot, you should retain root after a factory reset. If a factory reset doesn't work, you can try flashing one of the safe upgrade packages in Odin and re-rooting.
blindmanpb said:
If you can retain root after a reboot, you should retain root after a factory reset. If a factory reset doesn't work, you can try flashing one of the safe upgrade packages in Odin and re-rooting.
Click to expand...
Click to collapse
Edit: double posted for some reason
blindmanpb said:
If you can retain root after a reboot, you should retain root after a factory reset. If a factory reset doesn't work, you can try flashing one of the safe upgrade packages in Odin and re-rooting.
Click to expand...
Click to collapse
Factory reset did nothing. Now it doesn't even let me try to sign in. Just straight to the can't connect error.
I found a Google Apps package that has all the Google Apps in it but when I tried to flash the zip it said I had the wrong one. Could someone point me in the right direction? Would reinstalling the gapps package even do anything? Any help is greatly appreciated. Until I fix this my phone is practically unusable.
The gapps package said it couldn't install when I tried the zip from twrp. I'm really in need of some help. I can't use my phone at all since I've factory reset it and the play store won't work.
Edit: I tried wiping the cache and dalvik cache in twrp and now my phone is boot looping. Yay
HollowKyo said:
The gapps package said it couldn't install when I tried the zip from twrp. I'm really in need of some help. I can't use my phone at all since I've factory reset it and the play store won't work.
Edit: I tried wiping the cache and dalvik cache in twrp and now my phone is boot looping. Yay
Click to expand...
Click to collapse
Is this a custom rom that you're on or official build, and if so, which build are you on? If you're on the latest official build 5.1.1 (BPA1), then like someone else suggested above, I'd suggest making sure that you have Samsung USB drivers installed on your PC, putting your phone in Downlode Mode, connecting it to the PC and using Odin to flash hsbadr's N910VVZW2BPA1 Stock Restore (Incremented) (your unlocked bootloader will be preserved) and twrp-2.8.5.0-trltevzw.img.tar, then using recovery to flash a permissive kernel such as MultiSystem kernel for TouchWiz 5.1.1. and then BETA-SuperSU-v2.71-20160331103524.zip to reroot. That should at least get your device booted up and working again.
livinxtreme2114 said:
Is this a custom rom that you're on or official build, and if so, which build are you on? If you're on the latest official build 5.1.1 (BPA1), then like someone else suggested above, I'd suggest making sure that you have Samsung USB drivers installed on your PC, putting your phone in Downlode Mode, connecting it to the PC and using Odin to flash hsbadr's N910VVZW2BPA1 Stock Restore (Incremented) (your unlocked bootloader will be preserved) and twrp-2.8.5.0-trltevzw.img.tar, then using recovery to flash a permissive kernel such as MultiSystem kernel for TouchWiz 5.1.1. and then BETA-SuperSU-v2.71-20160331103524.zip to reroot. That should at least get your device booted up and working again.
Click to expand...
Click to collapse
Thanks. I'll try this now.
I had that problem when i installed jasmine rom, what i did was boot in to recovery,wipe data and cache and install jasmine rom again and now is fine.
livinxtreme2114 said:
Is this a custom rom that you're on or official build, and if so, which build are you on? If you're on the latest official build 5.1.1 (BPA1), then like someone else suggested above, I'd suggest making sure that you have Samsung USB drivers installed on your PC, putting your phone in Downlode Mode, connecting it to the PC and using Odin to flash hsbadr's N910VVZW2BPA1 Stock Restore (Incremented) (your unlocked bootloader will be preserved) and twrp-2.8.5.0-trltevzw.img.tar, then using recovery to flash a permissive kernel such as MultiSystem kernel for TouchWiz 5.1.1. and then BETA-SuperSU-v2.71-20160331103524.zip to reroot. That should at least get your device booted up and working again.
Click to expand...
Click to collapse
When I try I get,
SW REV CHECK FAIL : [tz]Fused 2 > Binary 1
On my phone and,
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910VVRU2BPA1_StockRestore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> NON-HLOS.bin
<ID:0/008> NAND Write Start!!
<ID:0/008> boot.img
<ID:0/008> cache.img.ext4
<ID:0/008> modem.bin
<ID:0/008> recovery.img
<ID:0/008> rpm.mbn
<ID:0/008> sbl1.mbn
<ID:0/008> sdi.mbn
<ID:0/008> system.img.ext4
<ID:0/008> tz.mbn
<ID:0/008> RQT_CLOSE !!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
In odin.
HollowKyo said:
When I try I get,
SW REV CHECK FAIL : [tz]Fused 2 > Binary 1
Click to expand...
Click to collapse
Then your bootloader version most likely doesn't match the file you're flashing. Do you know the last official build that you were on, and which file that I linked you to did you attempt to Odin flash just now, the Stock Restore one or the Stock Restore Incremented? If you at any point accepted the official OTA to Lollipop, then your bootloader has been incremented, meaning you'll need to flash the Stock Restore Incremented file. However, if you stayed on Kit Kat, then flash the plain Stock Restore file.
livinxtreme2114 said:
Then your bootloader version most likely doesn't match the file you're flashing. Do you know the last official build that you were on, and which file that I linked you to did you attempt to Odin flash just now, the Stock Restore one or the Stock Restore Incremented? If you at any point accepted the official OTA to Lollipop, then your bootloader has been incremented, meaning you'll need to flash the Stock Restore Incremented file. However, if you stayed on Kit Kat, then flash the plain Stock Restore file.
Click to expand...
Click to collapse
I did take the ota. Now it boots straight to odin mode and says to use verizon software repair assistant.
I was on 5.1.1 I see what I need. I'll try this right now.
HollowKyo said:
I did take the ota. Any chance you could link me the download I need? Now it boots straight to odin mode and says to use verizon software repair assistant.
Click to expand...
Click to collapse
That's okay, it'll do that when ever there has been a flash fail. We can fix it. If you accepted the official OTA to Lollipop then your bootloader has been incremented, meaning you'll need to flash the N910VVRU2BPA1_StockRestore_Incremented.tar.md5.7z file. Be sure and visit the original post and give hsbadr thanks for his restore file though.
livinxtreme2114 said:
That's okay, it'll do that when ever there has been a flash fail. We can fix it. If you accepted the official OTA to Lollipop then your bootloader has been incremented, meaning you'll need to flash the N910VVRU2BPA1_StockRestore_Incremented.tar.md5.7z file. Be sure and visit the original post and give hsbadr thanks for his restore file though.
Click to expand...
Click to collapse
Followed your instructions. I am now back up and running at 100% and rooted. Thank you so much.
HollowKyo said:
Followed your instructions. I am now back up and running at 100% and rooted. Thank you so much.
Click to expand...
Click to collapse
That's awesome. Glad I could help you out, brother.
livinxtreme2114 said:
That's awesome. Glad I could help you out, brother.
Click to expand...
Click to collapse
That was some fantastic assistance you gave there. way to represent the community well :good::good::good:
sudermatt said:
That was some fantastic assistance you gave there. way to represent the community well :good::good::good:
Click to expand...
Click to collapse
I really appreciate that!
I bought the phone locally, knowing of the issue. The seller claimed that it worked fine before, but started having this No Singal issue recently. The model of my motherboard is G960F, and right now the android version that's on my S9 is Android Pi; SM-G960U1. My IMEI is there. I am not getting to flash anything because of Qualcomm Secureboot. Any advice given would be appreciated, thanks in advance.
xcodydoe said:
I bought the phone locally, knowing of the issue. The seller claimed that it worked fine before, but started having this No Singal issue recently. The model of my motherboard is G960F, and right now the android version that's on my S9 is Android Pi; SM-G960U1. My IMEI is there. I am not getting to flash anything because of Qualcomm Secureboot. Any advice given would be appreciated, thanks in advance.
Click to expand...
Click to collapse
huh? you cant flash anything in Odin?
youdoofus said:
huh? you cant flash anything in Odin?
Click to expand...
Click to collapse
Nope Says "FAILED" and something about secureboot
xcodydoe said:
Nope Says "FAILED" and something about secureboot
Click to expand...
Click to collapse
did you do a factory reset from recovery with a google account still logged into the phone or something?
youdoofus said:
did you do a factory reset from recovery with a google account still logged into the phone or something?
Click to expand...
Click to collapse
Nope, no google account here
EDIT: I believe it has something to do with the latest security patch and bootloader
xcodydoe said:
Nope, no google account here
EDIT: I believe it has something to do with the latest security patch and bootloader
Click to expand...
Click to collapse
that doesnt make sense unless youre trying to flash firmware with a bootloader revision prior to the last one that was flashed on your phone. Get the most recent firmware for your specific country here. Use the regular CSC file so that it will completely factory reset your phone and that should fix your issue. Let me know what happens after you flash that. And download it with the Frija tool. Not sure if i mentioned that tool already as i cant see the prior responses when replying and ive mentioned it several times today already lol
youdoofus said:
that doesnt make sense unless youre trying to flash firmware with a bootloader revision prior to the last one that was flashed on your phone. Get the most recent firmware for your specific country here. Use the regular CSC file so that it will completely factory reset your phone and that should fix your issue. Let me know what happens after you flash that. And download it with the Frija tool. Not sure if i mentioned that tool already as i cant see the prior responses when replying and ive mentioned it several times today already lol
Click to expand...
Click to collapse
Thank you, I'll try that and let you know.
youdoofus said:
that doesnt make sense unless youre trying to flash firmware with a bootloader revision prior to the last one that was flashed on your phone. Get the most recent firmware for your specific country here. Use the regular CSC file so that it will completely factory reset your phone and that should fix your issue. Let me know what happens after you flash that. And download it with the Frija tool. Not sure if i mentioned that tool already as i cant see the prior responses when replying and ive mentioned it several times today already lol
Click to expand...
Click to collapse
I'm not getting to flash it with Odin. This is the error that I'm getting. http://prntscr.com/p0f5qa
Downloaded the firmware using Frija
youdoofus said:
that doesnt make sense unless youre trying to flash firmware with a bootloader revision prior to the last one that was flashed on your phone. Get the most recent firmware for your specific country here. Use the regular CSC file so that it will completely factory reset your phone and that should fix your issue. Let me know what happens after you flash that. And download it with the Frija tool. Not sure if i mentioned that tool already as i cant see the prior responses when replying and ive mentioned it several times today already lol
Click to expand...
Click to collapse
Tried exactly this and I'm getting this error http://prntscr.com/p2gu5t
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1301)..
<ID:0/009> File analysis..
<ID:0/009> skip file list for home binary
<ID:0/009> Home Binary Download
<ID:0/009> Total Binary size: 612 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> cache.img
<ID:0/009> Complete(Write) operation failed.
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
xcodydoe said:
Tried exactly this and I'm getting this error http://prntscr.com/p2gu5t
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1301)..
<ID:0/009> File analysis..
<ID:0/009> skip file list for home binary
<ID:0/009> Home Binary Download
<ID:0/009> Total Binary size: 612 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> cache.img
<ID:0/009> Complete(Write) operation failed.
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Have you ever used Odin successfully on this computer before?
youdoofus said:
Have you ever used Odin successfully on this computer before?
Click to expand...
Click to collapse
Yeah, when the phone's Android version was at 8
xcodydoe said:
Yeah, when the phone's Android version was at 8
Click to expand...
Click to collapse
then redownload the 4 files, get a new copy of Odin, use a different cable and finally try a different computer if the first 3 didnt work
youdoofus said:
then redownload the 4 files, get a new copy of Odin, use a different cable and finally try a different computer if the first 3 didnt work
Click to expand...
Click to collapse
Can you link the latest version of Odin?
HTML:
xcodydoe said:
Can you link the latest version of Odin?
Click to expand...
Click to collapse
https://odindownload.com/