Develop Bugs

[RECOVERIES & ROOT] Yureka custom recoveries & Root without Changing Stock Recovery

[RECOVERIES & ROOT] Yureka custom recoveries & Root without Changing Stock Recovery
Note : This tutorial is for YU Yureka based on CM11 (KK 4.4.4) 32bit architecture
and
do it on your own risk, I will not be responsible if you brick your phone
Here is the detailed guide and collection of stock and all custom recoveries for YU Yureka and detailed guide to Root YU Yureka without changing Stock Recovery
Requirements
1. YU Yureka (obviously) with USB Data cable
2. PC / Laptop (Having Windows installed at least Windows 7 or above)
3. Drivers (Windows Automatically detect and install the required drivers)
4. ADB & Fastboot binary package that can be downloaded from XDA 15 seconds ADB Installer v1.4.2']http://forum.xda-developers.com/showthread.php?t=2588979
5. Custom Recovery (Anyone in which you are interested CWM, PhiZ, TWRP)
6. Latest SuperSU.zip file to root your phone
Warning: This process may delete all data stored in internal storage so better backup all the files stored in internal storage.
Step One
Enable USB Debugging on your device you can just follow these steps:
Go to Settings> About phone and keep taping on build number at least 7 times or till it appears "You are a developer now",
Now again go to settings>developer option (only after the previous step it will be enabled)> check/select USB debugging.
Step Two
Unlock your bootloader to flash custom recovery and root.
Here is the process
1. Download the adb & fastboot binary package and install it.
2. Put your phone into FASTBOOT mode by following anyone from below methods :
Method 1 (easiest)
-------------------
a. Power down phone
b. Plug USB cable to your PC
c. Press and hold Vol Up button and plug other end of USB to your device, soon you will see the fastboot screen.
(or without plugging USB Cable, Press and Hold Power and Vol Up buttons simultaneously, until you see the screen
"FASTBOOT MODE"
Method 2
---------
a. While your phone is Power On, plug USB Data Cable with PC and Phone (USB Debuging must be Enable)
b. Open Command Prompt on your PC (with Administartor rights) and type the following command
adb -s 0x1ebf devices
You will get results something like that :
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
3a289c2 device
*Note : If you get "authorization message" then look on your mobile screen and authorize your PC and run the command again.
c. Now note down the device no. (for e.g. in above "3a289c2") and type the following command
adb -s 3a289c2 reboot bootloader
[*Note replace the device id with your id (here 3a289c2), that you got in last command]
Now your phone must be booted into fastboot mode. A screen with "Fastboot Mode" should be appear on your phone.
3. Device drivers will get installed by windows (please wait for the driver installation to complete)
4. After driver installation is done go to the folder where you have extracted the package
5. Now open elevated DOS command prompt (terminal) on your PC and go into the same folder where you saved the recovery file
(*Note : to start command prompt directly from desired folder, while holding the Shift Key Right Click on folder and select start "open command window here")
6. Type the following command to check if the device was detected in fastboot mode
fastboot -i 0x1ebf devices
you should get output like : 2a25d00 fastboot
if you don't get similar output it means that the drivers weren't correctly installed or the device wasn't connected properly
7. If the output is similar to above then run the following command:
fastboot -i 0x1ebf oem unlock
you should get output something like :
.....
OKAY [ 0.003s]
finished. total time: 0.004s
8. Now your bootloader is now unlocked.
*Note : if you want to re-lock your bootloader again (for warranty on any other reason), again boot into fastboot mode and this time type the following command and enter
fastboot -i 0x1ebf oem lock
Step Three
Boot your phone into recovery (temporarily or permanently) and root your phone
1. Download SuperSU.zip and put it on root of your internal or external SD card
2. To load custom recovery (CWM / TWRP / PhiZ) temporarily, now type this command in terminal :
fastboot -i 0x1ebf boot CWM_6.0.5.1_recovery-yu.img
*Note 1 : if you want to flash the custom recovery permanently then us the following command
fastboot -i 0x1ebf flash CWM_6.0.5.1_recovery-yu.img
*Note 2 : if your download custom recovery is named differently (here CWM_6.0.5.1_recovery-yu.img) then while writing the above commands you need to put the name of the recovery same as as your saved file name (anyone CWM / Phiz / TWRP)
3. Done ! You loaded custom recovery temporarily, if command used with "boot" hence to root your phone, proceed to next section (step 5).
or
If you flashed recovery permanently, using command with "flash" then boot your phone into recovery. To do so, you have Two options
i) type the following command and press enter : adb -s 3a289c2 reboot recovery
or
ii) power off your phone, after then press and hold "Vol up+ Vol down + Power" buttons simultaneously to boot into custom recovery.
Now to root your phone proceed with next section (step 5).
Root your phone
5. To gain root access, flash SuperSu.zip that is stored on your internal or external SD card (in step 1)
6. Choose reboot phone and enjoy rooted phone with stock or custom recovery !
Special Note 1
I didn't tested, but came to know that root doesn't effect OTA update on Yureka.
You can get OTA updates with root but after the OTA update is flashed you will loose root access. To keep it or to avoid this please go to System Settings -> Developer Options -> UNTICK -"Update CM Recovery" (update recovery while installing system updates)
Even though if someone want to go back to Stock recovery, then download the official stock recovery (link no. 6 above) and flash it using command in fastboot mode (second command in step 2 under head "STEP THREE")
Downloads
1. 15 seconds ADB Installer v1.4.2 http://forum.xda-developers.com/showthread.php?t=2588979
2. Super SU latest v2.46 http://download.chainfire.eu/696/SuperSU/UPDATE-SuperSU-v2.46.zip
3. CWM 6.0.5.1 https://s.basketbuild.com/devs/vishal_android_freak/yu/yureka
OR http://d-h.st/ElAe
4. PhilZTouch 6.59 based on CWM v6.0.5.1 http://www.androiddevs.net/downloads/
OR http://d-h.st/UqWK
5. TWRP 2.8.5.0 http://techerrata.com/browse/twrp2/tomato
OR https://www.androidfilehost.com/?fid=95916177934528156
OR http://d-h.st/5wDD
6. YU Yureka Official Stock Recovery http://d-h.st/tQ1k
Special Note 2
Without the vendor id, phone will not get detected in fastboot mode.
Like if you want to check fastboot type this :
fastboot -i 0x1ebf devices
therefore, always add "i -0x1ebf" after fastboot and then write your command

aabidhashmi said:
Here is is collection of all custom recoveries for YU Yureka and detailed guide to Root YU Yureka without changing Stock Recovery
Requirements
1. YU Yureka (obviously) with USB Data cable
2. PC / Laptop (Having Windows installed at least Windows 7 or above)
3. Drivers (Windows Automatically detect and install the required drivers)
4. ADB & Fastboot binary package that can be downloaded from XDA 15 seconds ADB Installer v1.4.2']http://forum.xda-developers.com/showthread.php?t=2588979
5. Custom Recovery (Anyone in which you are interested CWM, PhiZ, TWRP)
6. Latest SuperSU.zip file to root your phone
Warning: This process may delete all data stored in internal storage so better backup all the files stored in internal storage.
Step One
Enable USB Debugging on your device you can just follow these steps:
Go to Settings> About phone and keep taping on build number at least 7 times or till it appears "You are a developer now",
Now again go to settings>developer option (only after the previous step it will be enabled)> check/select USB debugging.
Step Two
Unlock your bootloader to flash custom recovery and root.
Here is the process
1. Download the adb & fastboot binary package and install it.
2. Power down phone
3. Plug USB cable to your PC
4. Press and hold Vol Up button and plug other end of USB to your device, soon you will see the fastboot screen.
(or without plugging USB Cable, Press and Hold Power and Vol Up buttons simultaneously, until you see the screen
"FASTBOOT MODE"
5. Device drivers will get installed by windows (please wait for the driver installation to complete)
6. After driver installation is done go to the folder where you have extracted the package
7. Now open elevated DOS command prompt (terminal) on your PC and go into the same folder where you saved the recovery file
* to start command prompt directly from desired folder, while holding the Shift Key Right Click on folder and select start "open command window here"
8. Type the following command to check if the device was detected in fastboot mode
fastboot -i 0x1ebf devices
you should get output like : 2a25d00 fastboot
if you don't get similar output it means that the drivers weren't correctly installed or the device wasn't connected properly
9. If the output is similar to above then run the following command:
fastboot -i 0x1ebf oem unlock
you should get output something like :
.....
OKAY [ 0.003s]
finished. total time: 0.004s
10. Now your bootloader is now unlocked.
Step Three
Root your phone without changing your stock recovery
1. Download SuperSU.zip and put it on root of your internal or external SD card
2. To load custom recovery (CWM / TWRP / PhiZ) temporarily, now type this command in terminal :
fastboot -i 0x1ebf boot recovery CWM_6.0.5.1_recovery-yu.img
*Note : if your download custom recovery is named differently (here CWM_6.0.5.1_recovery-yu.img) then while writing the above command you need to put the name of the recovery same as as your saved file name (anyone CWM / Phiz / TWRP)
Done ! You flashed custom recovery temporarily.
3. Now press and hold "Vol up+ Vol down + Power" buttons simultaneously to boot into custom recovery.
4. To gain root access flash SuperSu.zip that is stored on your internal or external SD card (in step 1)
5. Choose reboot phone and enjoy rooted phone without changing stock recovery !
Downloads
1. 15 seconds ADB Installer v1.4.2 http://forum.xda-developers.com/showthread.php?t=2588979
2. Super SU latest v2.46 http://download.chainfire.eu/696/SuperSU/UPDATE-SuperSU-v2.46.zip
3. CWM 6.0.5.1 https://s.basketbuild.com/devs/vishal_android_freak/yu/yureka
OR http://d-h.st/ElAe
4. PhilZTouch 6.59 based on CWM v6.0.5.1 http://www.androiddevs.net/downloads/
OR http://d-h.st/UqWK
5. TWRP 2.8.5.0 http://techerrata.com/browse/twrp2/tomato
OR https://www.androidfilehost.com/?fid=95916177934528156
OR http://d-h.st/5wDD
Special Note
Without the vendor id, phone will not get detected in fastboot mode.
Like if you want to check fastboot type this :
fastboot -i 0x1ebf devices
therefore, always add "i -0x1ebf" after fastboot and then write your command
Click to expand...
Click to collapse
Few errors noted:
1. You can't say flashing recovery when you are booting it.
2. In step 3 point 3 is not valid because when your command is to boot it will automatically boot into recovery you need not use combination keys.
3. Last point vender id is wrong !!!
Few suggestions:
1. It feels like you have not tested this by yourself
2. There is already a guide for "rooting without flashing recovery". Search before posting.
Regards
aashking

aashking said:
Few errors noted:
1. You can't say flashing recovery when you are booting it.
2. In step 3 point 3 is not valid because when your command is to boot it will automatically boot into recovery you need not use combination keys.
3. Last point vender id is wrong !!!
Few suggestions:
1. It feels like you have not tested this by yourself
2. There is already a guide for "rooting without flashing recovery". Search before posting.
Regards
aashking
Click to expand...
Click to collapse
Dear aaskking
Thanks to inform. Here is the corrections
1 & 2 - Tutorial updated with "boot" and "flash" commands separately.
3 + Vendor ID is correct nothing wrong in it.
4 - I already tested all those procedures and commands. I never post anything without testing.
5 - Yes, I also seen that available guide, but that is not so much detailed and also required files links are not provided.
Anyway, thanks for your suggestions.

aabidhashmi said:
Dear aaskking
Thanks to inform. Here is the corrections
1 & 2 - Tutorial updated with "boot" and "flash" commands separately.
3 + Vendor ID is correct nothing wrong in it.
4 - I already tested all those procedures and commands. I never post anything without testing.
5 - Yes, I also seen that available guide, but that is not so much detailed and also required files links are not provided.
Anyway, thanks for your suggestions.
Click to expand...
Click to collapse
EDIT : You can get OTA updates with root..
After the update is flashed you will loose root access ..
To keep it or to avoid this please write the following step
STEP) In Developer Option UNTICK -"Update CM Recovery".
That's it.. Cheers mate wonderful thread.. @aabidhashmi @aashking

arjunsingh1000 said:
EDIT : You can get OTA updates with root..
After the update is flashed you will loose root access ..
To keep it or to avoid this please write the following step
STEP) In Developer Option UNTICK -"Update CM Recovery".
That's it.. Cheers mate wonderful thread.. @aabidhashmi @aashking
Click to expand...
Click to collapse
Thanks Arjun Singh @arjunsingh1000 for suggestion and appreciation
Post updated ...

aabidhashmi said:
Thanks Arjun Singh @arjunsingh1000 for suggestion and appreciation
Post updated ...
Click to expand...
Click to collapse
Great mate cheers just checked and tried that ota updates are available and work.. On stock recovery... Locked bootloader and with root..
Achieved this by downgrading to the very first cm11 firmware and got then rooted it and locked the bootloader then I just booted it and got the incremental update .. Downloaded and flashed .. Works perfectly.. Root not lost due to the untick in dev options..

Thanks again Arjun Singh, for confirming OTA updates are working.
I am already on Stock ROM & recovery {rooted} and tried the same procedure {locked the bootloader}, but no updates for me.
Is updates are really there, or something wrong with me ?
Sent from my AO5510 using Tapatalk

I am simply unable to get the device listed in command prompt after fastboot mode is enabled. my phone has option to boot into fastboot mode in power options. i tried that option, i tried using command to boot into fastboot. But somehow, when phone is in fastboot mode, it does not get detected by fastboot application (even though windows installs drivers successfully).
I have tried 3 different laptops. All had same problem. No idea how to solve this.

aabidhashmi said:
Thanks again Arjun Singh, for confirming OTA updates are working.
I am already on Stock ROM & recovery {rooted} and tried the same procedure {locked the bootloader}, but no updates for me.
Is updates are really there, or something wrong with me ?
Sent from my AO5510 using Tapatalk
Click to expand...
Click to collapse
Well I guess you are on the latest build XN0PHQ I guess? Another beta update was made but not rolled out it is um XNPH08P I know its a little late but just in case you don't know..
---------- Post added at 05:30 PM ---------- Previous post was at 05:28 PM ----------
jitendragarg said:
I am simply unable to get the device listed in command prompt after fastboot mode is enabled. my phone has option to boot into fastboot mode in power options. i tried that option, i tried using command to boot into fastboot. But somehow, when phone is in fastboot mode, it does not get detected by fastboot application (even though windows installs drivers successfully).
I have tried 3 different laptops. All had same problem. No idea how to solve this.
Click to expand...
Click to collapse
Ahahahaah... I know just the way... Do not reboot via adb ...
Switch off your phone remove your battery and put it back in do not turn it on.. But connect your USB cable and at the same time hold the power up or maybe down button .. Voila your in fastboot which will get detected .. Don't forget to use the vendor id.

arjunsingh1000 said:
Ahahahaah... I know just the way... Do not reboot via adb ...
Switch off your phone remove your battery and put it back in do not turn it on.. But connect your USB cable and at the same time hold the power up or maybe down button .. Voila your in fastboot which will get detected .. Don't forget to use the vendor id.
Click to expand...
Click to collapse
I tried this method but phone does not get detected in fastboot mode at all. I have drivers installed for all different modes I connect my phone as. No luck at all.
Also, weird thing is, I have an option to directly go to fastboot mode from the power menu.

Jitendra Garg
Your driver's are not installed
As there is no special drivers setup, so connect your PC with Internet then plug your phone and let Windows install drivers automatically.
Sent from my AO5510 using Tapatalk

Total Nub's guide to rooting Qmobile Q Infinity & Micromax Canvas Inifinity

After failing some 1-click rooting methods, for the first time I tried to do it the hard way.
That turned out to be a pretty easy way thanks to some handy links to drivers and other files I found.
Infinity thanks to the thread I found platform-tools from and the website called "getdroidtips" for the Custom TWRP for the HS2.
NOTE: THIS GUIDE WILL WIPE YOUR DEVICE SO BE PREPARED
Standard warning: FOLLOW THIS GUIDE AT YOUR OWN RISK. REMEMBER, AS PER MY NAME I AM A TOTAL NUB. I DO NOT TAKE RESPONSIBILITY FOR YOUR PHONE MALFUNCTIONING, BRICKING, BLOWING UP OR DROWNING IN COOKING OIL (rip my Elephone S7)
Pastebin code for missing links: F2RGqM1A
1) Preparation
Download the latest Flashable.Zip from [ ]
Place SuperSu.zip in your sd card or internal storage
Enable Developer Options by going to Settings -> "About Phone" -> Click "Software Version" 7-8 times
Go to developer Options in Settings
Enable OEM Unlocking
Enable USB Debugging
Shutdown your phone by holding the power button
Boot into fastboot by holding the Volume Up key + Power Button
Press Volume Down key to get into fastboot
2) On your Windows PC:
Download the file from [ ] and extract the platform-tools folder (I extract to "D:\Downloads" in this example)
Download the Custom TWRP from [ ] and place it inside the platform-tools folder
Connect your device to your computer
press Win+R, type cmd and press enter
2.1) (not always needed)
If your device won't connect or the steps below don't work, try updating drivers:
Connect your phone while it's in fastboot
open start menu, search and open Device Manager
check inside Portable Devices or Android Devices for your phone's name
or look for Android Bootloader Interface
if it's not there, it might be named something else, with an icon that has a yellow triangle inside it.
Right click it, Update Driver
> Browse my computer for driver software
> Let me pick from a list of available drivers on my computer
> select Android Bootloader Interface
to check if you are connected, type "fastboot devices" in cmd and you'll see a device code
3) Unlocking Bootloader
In cmd, enter the following commands:
Code:
D:
cd D:\Downloads\platform-tools
fastboot oem unlock-go
THIS STEP WILL WIPE YOUR DEVICE DATA
wait for restart
4) Booting into TWRP
Go to device Settings again and ensure OEM Unlocking and USB Debugging are still Enabled. Reboot into fastboot.
In cmd:
Code:
fastboot boot twrp-3.1.1-0-20171128-UNOFFICIAL-HS2.img
(In case above cmd line doesn't work, type "fastboot boot twrp" and press Tab)
5) Backing up your rom and data (Optional but recommended)
Inside TWRP, Click Backup, tick everything, select desired directory and swipe to backup.
Reboot and follow step 5 again if needed
6) Installing SuperSU with root privileges
Inside TWRP, Click Install and select SuperSU.zip
Swipe to install and reboot
Enjoy

Please port miui 9 or lineage os 15 for micromax canvas infinity hs2

NubbyMcNubNub said:
After failing some 1-click rooting methods, for the first time I tried to do it the hard way.
That turned out to be a pretty easy way thanks to some handy links to drivers and other files I found.
Infinity thanks to the thread I found platform-tools from and the website called "getdroidtips" for the Custom TWRP for the HS2.
NOTE: THIS GUIDE WILL WIPE YOUR DEVICE SO BE PREPARED
Standard warning: FOLLOW THIS GUIDE AT YOUR OWN RISK. REMEMBER, AS PER MY NAME I AM A TOTAL NUB. I DO NOT TAKE RESPONSIBILITY FOR YOUR PHONE MALFUNCTIONING, BRICKING, BLOWING UP OR DROWNING IN COOKING OIL (rip my Elephone S7)
Pastebin code for missing links: F2RGqM1A
1) Preparation
Download the latest Flashable.Zip from [ ]
Place SuperSu.zip in your sd card or internal storage
Enable Developer Options by going to Settings -> "About Phone" -> Click "Software Version" 7-8 times
Go to developer Options in Settings
Enable OEM Unlocking
Enable USB Debugging
Shutdown your phone by holding the power button
Boot into fastboot by holding the Volume Up key + Power Button
Press Volume Down key to get into fastboot
2) On your Windows PC:
Download the file from [ ] and extract the platform-tools folder (I extract to "D:\Downloads" in this example)
Download the Custom TWRP from [ ] and place it inside the platform-tools folder
Connect your device to your computer
press Win+R, type cmd and press enter
2.1) (not always needed)
If your device won't connect or the steps below don't work, try updating drivers:
Connect your phone while it's in fastboot
open start menu, search and open Device Manager
check inside Portable Devices or Android Devices for your phone's name
or look for Android Bootloader Interface
if it's not there, it might be named something else, with an icon that has a yellow triangle inside it.
Right click it, Update Driver
> Browse my computer for driver software
> Let me pick from a list of available drivers on my computer
> select Android Bootloader Interface
to check if you are connected, type "fastboot devices" in cmd and you'll see a device code
3) Unlocking Bootloader
In cmd, enter the following commands:
THIS STEP WILL WIPE YOUR DEVICE DATA
wait for restart
4) Booting into TWRP
Go to device Settings again and ensure OEM Unlocking and USB Debugging are still Enabled. Reboot into fastboot.
In cmd:
(In case above cmd line doesn't work, type "fastboot boot twrp" and press Tab)
5) Backing up your rom and data (Optional but recommended)
Inside TWRP, Click Backup, tick everything, select desired directory and swipe to backup.
Reboot and follow step 5 again if needed
6) Installing SuperSU with root privileges
Inside TWRP, Click Install and select SuperSU.zip
Swipe to install and reboot
Enjoy
Click to expand...
Click to collapse
Hi please help me, after flashing recovery my phone is on bootloop now, what do i do

Hem97 said:
Please port miui 9 or lineage os 15 for micromax canvas infinity hs2
Click to expand...
Click to collapse
I wish I could.
Sudhangshu said:
Hi please help me, after flashing recovery my phone is on bootloop now, what do i do
Click to expand...
Click to collapse
Did you try "flashboot boot twrp..." like in my guide or "flashboot flash twrp..."?
And which twrp image did you use?
In any case, if you can still get to the fastboot screen, try booting with the twrp image in Step 4 above (download links in the pastebin link)

NubbyMcNubNub said:
I wish I could.
Did you try "flashboot boot twrp..." like in my guide or "flashboot flash twrp..."?
And which twrp image did you use?
In any case, if you can still get to the fastboot screen, try booting with the twrp image in Step 4 above (download links in the pastebin link)
Click to expand...
Click to collapse
Hi, "flashboot boot twrp" wasnt working at all, so i tried "flashboot flash twrp" and all i have is a bootloop. So after flashing recoveru i booted my phone to fastboot and run the command, " flashboot boot recovery recovery.img" where recovery is the custom recovery image and it booted into recovery. Then there is one more step to do that allowed me to finally boot into my os. Its working fine and i still have twrp installed on my phone
---------- Post added at 06:53 PM ---------- Previous post was at 06:49 PM ----------
NubbyMcNubNub said:
I wish I could.
Did you try "flashboot boot twrp..." like in my guide or "flashboot flash twrp..."?
And which twrp image did you use?
In any case, if you can still get to the fastboot screen, try booting with the twrp image in Step 4 above (download links in the pastebin link)
Click to expand...
Click to collapse
Btw i dont find any pastebin links, im sorry im just a noob too..... Lol

Want custom rom for Qmobile Qinfinity
I want a custom rom for Qmobile Qinfinity.
Because its own rom lags and does not have full features. Please give the rom like lineage os,RR,Or Stock
Please Help?:good:

hi bro,recently i just buy a new phone which is micromax canvas infinity.i have rooted my phone successfully,but there are no custom roms available for this phone.can you develop any custom rom for this phone?that will be very helpful...

Custom recovery TWRP for Infocus bingo 21 m430

Working TWRP custom recovery for infocus m430 bingo 21.
To do this, you would require:
data cable if not rooted phone
stock marshmallow running infocus m430 bingo 21
if not rooted, you need adb and fastboot installed on your computer-> google this if never heard of.
download attachments of this post(twrp_recoveryimg)
Problems:
Before you do this, you need to know the temporary problems you would encounter and their solutions
TWRP is in other language but you can use this link to bring it back to english, 1 time thing
http://www.teamandroid.com/2017/04/30/change-twrp-recovery-language-english/
if the above link does not work out, there are lot of youtube videos to enable english in twrp. google out.
once mobile boots into recovery, it will not come back to normal. There is a bit being set by infocus on some partition to reboot to recovery always. Until i find it, you would have to use following the process below to come back to normal boot.
Steps to come back to normal boot
1. in recovery, select option advanced
2. select adb sideload option
3. swipe to start sideload(this will start adb in recovery mode)
4. cancel
5. in your computer type
Code:
adb reboot bootloader
6. After mobile shows fastboot mode: in top of the screen with infocus logo type the below command
Code:
fastboot continue
7. This should boot your device back to normal android boot.
8. You have to do this every time you boot to recovery.
Now follow the below procedures to get a custom recovery on your mobile.
Procedure 1 : (does not require root)
unlock developer options -> google this if you never knew this until now.
unlock oem. Do this by going to developer options -> oem unlocking(enable).
unzip the recovery image attachment
enter fastboot by typing following command.
Code:
adb reboot bootloader.
flash twrp_recovery.img in the attachement. Do this by using following commands.(place your twrp_recovery.img in the current directory of terminal / cmd)
Code:
fastboot erase recovery
fastboot flash recovery twrp_recovery.img
Procedure 2 : (requires root) I have not tried this but it would work. Try it on your own risk.
Download the attachments
send them to your mobile sdcard
install mobile uncle tools or similar app from play store which would flash recovery images
select install recovery and point to the twrp_recovery.img in your sdcard.
Message me in case of questions or reply this thread.

Sir,where to type the code 'adb reboot bootloader' and other codes?

Want your contact number, for the purpose of custom recovery.
I tried that steps many times on my phone via pc. So help me for the custom recovery. I want your contact number to do this process correctly without worrying any problem occurs on my phone.

You should be able to find youtube video on how to install adb and fastboot online. After that, you should type those commands in command prompt in windows computer if you have or in terminal if you have linux or mac.
[email protected] said:
Sir,where to type the code 'adb reboot bootloader' and other codes?
Click to expand...
Click to collapse

Gimme your whatsapp or telegram number, i should be able to reach you out.
iyyappan001 said:
I tried that steps many times on my phone via pc. So help me for the custom recovery. I want your contact number to do this process correctly without worrying any problem occurs on my phone.
Click to expand...
Click to collapse

Problem while using adb fastboot method in In focus M425
What about infocus M425 phone ????

[root] redmi 4x root

Firstly this is my first helpful post so be gentle.
How to root the Redmi 4x
First off I am not accountable if your fry your device or shut down the power grid etc.
Alright. It took me some research and trial and error but I found the CORRECT way to root the Redmi 4x.
Needed files:
Lasted version of the magisk zip. DO NOT USE ANY VERSION OF SUPER SU. IT CAUSES BOOTLOOP.
TWRP for Redmi 4x
Lazy patcher.
Adb and fastboot files.
Step one:
Ensure your bootloader is unlocked. If not search XDA for a thread there are multiple threads showing you how to do it. Once that's done let's move on.
Step 2:
Alright let's get going with flashing TWRP first.
You need to enable developer options and enable USB debugging on your Redmi. To do that go to settings>about devices>scroll down>continually tap on MIUI version and a toast notification will tell you that you are now a developer>go to developer option under the more options tab and enable USB debugging.
Step 3:
Now that we've got USB debugging we can connect to Adb. Firstly download all aforementioned files and place them in the same folder as your Adb installation for ease of access. Now open up a command prompt in that folder by either typing "cmd" into the address bar or shift+right click and select open command window here. Now you need to connect your phone via USB to your computer and ensure it is connected by entering "adb devices" into the command window.
Step 4: commands
Here are the commands you will need to enter. I recommend making a backup of everything first.
Enter these commands
adb reboot bootloader
Fastboot flash recovery (put TWRPS full file name here including the .zip)
Wait for it to finish.
Now DO NOT BOOT TO SYSTEM.
Enter in fastboot reboot and hold volume up to enter recovery. If you boot to system it will remove twrp and you will have to reflash it.
Once in Twrp check the box to allow modifications and slide right.
Go to advanced and the ADB sideboard.
Now flashing magisk and lazy patcher.
Reconnect your phone to the computer and leave Twrp on sideload mode.
Enter this command
adb sideload (lazy patchers full file name here)
Now I made sure my phone still booted to system after this because every time I flashed SuperSU it would boot loop.
Once your back in sideload mode let's flash magisk.
adb sideload (magisks full file name here).
Once it's done select reboot to system from Twrp and enjoy your root!!
Again I say do not use any flashable root other than magisk. I don't know if I had a specific problem but every single one I tried resulted in bootloop.

Oppo A83 [CPH1729] TWRP RECOVERY

⚠Warning: This is not official TWRP, use it at your own risk!!!
Data will be erased. Back up if neccessary
This device is kind of weird so to flash twrp you need these things:
1. Prepare materials​
Install driver so as to have access to preloader (Just install automatically and no need to do anything in device manager)
This software to access to preloader -> fastboot (fastboot is somehow not available via adb methods) Enter fastboot
This tool for flashing
2. Unlock bootloader (need testpoint, python, git (optional) - you can search on google)​
Use this tool - go to this section. Follow guides to unlock bootloader (remember to use testpoint not hardware buttons)
3. Enter fastboot mode​
Use latest MTK META Ultility tool
Select Reboot Fastboot Mode in BRom section
Hold volume down button. While holding connect it to your computer
*Now your phone is in fastboot mode​4. Flash​
Open platform-tools folder in Downloads folder
Shift + Right click then "open command window here"
Input these commands into cmd
fastboot flash boot drag twrp file to cmd
fastboot flash recovery drag twrp file to cmd.
fastboot reboot. Swipe to allow modification in twrp (to make sure that stockboot wont replace twrp). After that reboot to recovery to make it installed on your device permanently.
Now your recovery is ready to flash file you can push stock image file to your root folder using adb command: "adb push. Drag the stock image file. /" (Because Decryption right now doesnt work on my device yet)
Enjoy
*Sounds crazy but it is required to make sure twrp is installed correctly​*If successful, when you power on, you will get a red section on top of your device. If you want to recover to stock recovery, flash the recovery.img below.​*Also, if you want to make your own twrp, you can try recovery.img below.​
Also thanks SebaUbuntu and Mofadal El-Tayeb (مُفَضَّل) for awesome apps
​
​​
​

Here is the PBRB version for this device

Hey I'm stuck in the third step.can you please help me?

Sorry for late reply. What problems do you have?

Is this the stock boot image you provided?

SAMIUL ISLAM 0 said:
Is this the stock boot image you provided?
Click to expand...
Click to collapse
Yes it is. I took it from OTA update

Hey friends
I want to upgrade my oppo a 83 fone to a costum rom to upgrade my androide to android 8 or higher

mahmoud2503 said:
Hey friends
I want to upgrade my oppo a 83 fone to a costum rom to upgrade my androide to android 8 or higher
Click to expand...
Click to collapse
Unfortunately, I have no custom roms available for this phone (