Nexus 7 2013 back cover melted - Nexus 7 (2013) Q&A

- Broke the Nexus 7 2013 touchscreen last year. Bought a new touchscreen.
- Replaced the screen following Fixez.com videos on youtube.
- Put the tablet inside an extra casing to protect it from any further accidents.
- Top portion of the touchscreen went unresponsive after couple of months. (Went pretty useless since I was not able to access notification bar)
- Didn't bother to use it for almost 6-9 months
- Found the tablet working last week. Started using it again. Top portion went unresponsive again.
- Removed the cased and opened it up to see back cover has melted slightly. Opened the back cover.
It looks like when I repaired the tablet I stuck the tape on the ribbon cable, there was some air gap in between the cable and the tape. The air got heated up, which caused the adhesive to burn, which caused the tape to burn, which burnt the back cover.
Images
imgur.com/a/gDkl0
Any help/suggestion/fix is appreciated.

Related

Broken LCD Screen, replaced it, now touch doesn't work

OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.

Loose side cover

Hi to everyone, I bought my nexus 2 months ago and now I found out that the side cover which frames the screen and the phone itself is loose. I can put my nail between the screen and the cover very easily and it bends. This morning when I took my phone it squeeked and it came frome the left side of the cover. Now every time I push it or touch this place it squeeks, it's like there is a free space. Another problem I found is that the phone has very dirt and dust at the bottom between the screen and the frame, and when I blowed there thia morning to get it out the glass at the very bottom (not the screen) under the soft keys sweated from inside. I don't know what to do. If I bring it to my operator to fix it or replace it they may say that I have dropped it and from that is the problem
kristian93 said:
Hi to everyone, I bought my nexus 2 months ago and now I found out that the side cover which frames the screen and the phone itself is loose. I can put my nail between the screen and the cover very easily and it bends. This morning when I took my phone it squeeked and it came frome the left side of the cover. Now every time I push it or touch this place it squeeks, it's like there is a free space. Another problem I found is that the phone has very dirt and dust at the bottom between the screen and the frame, and when I blowed there thia morning to get it out the glass at the very bottom (not the screen) under the soft keys sweated from inside. I don't know what to do. If I bring it to my operator to fix it or replace it they may say that I have dropped it and from that is the problem
Click to expand...
Click to collapse
Well, your options are limited, and if you don't want to spoil your warranty I would take it back to the store you bought it from.
Swype'ed on my CM10 Galaxy Nexus

[Q] Everything but the display works - Nexus 7 2013

This guy has the same problem: http://forum.xda-developers.com/nexus-7/help/nexus-7-screen-replacement-black-screen-t2811453
Hello, Everybody! One day I took my 2013 Nexus 7 on a walk and fell, resulting in a large crack across the screen. Half of the display was not touch-responsive. Recently, I obtained a digitizer replacement, pulled the tablet apart, and replaced it. I later found that I had removed a layer of black glass which appeared to be vital. Today I received a screen + digitizer assembly that contained the black glass. After removing many screws, I replaced the screen. After waiting about thirty minutes, I attempted to turn it on. At first, the screen stayed black. When I connected it to a computer and tried again, the speaker made a notification sound.
The tablet is running Android, but the screen is blank.
Thanks,
Thomas (D3C0D3)
You can confirm the tablet had life? As in when you "turned it on" and connected to your computer via USB, did you computer recognise it?
The Digitiser (top glass layer) when cracked over the screen will make the touch fail, my nexus had a chipped digi on the bottom which spread to the middle... The LCD however was fine.
When I replaced the Digitiser by heating it off the frame and swapping over. My repair went fine and my nexus 7 flo is good as new.
In short, if you are saying you have power and sound but no display; your LCD is either (a): Loose, I do believe it is the orange coloured ribbon cable. Or (b): Damaged, either by yourself when fitting or while it was in transit.
If it is B; simply buy a replacement again.. Make sure you do the entire repair on a flat surface, heat the glue and pry carefully with a tool such as an iSesimo; as to keep your frame intact.. Replace the glue or adhesive tape THOROUGHLY as to ensure the new digitiser stays attached to the frame, as it is only stuck by what you put on.
The LCD is very fragile, be careful.
Sent from my Nexus 7 using XDA Premium 4 mobile app

replacing screen from zenfone 2 551

Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
pulesky said:
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
Click to expand...
Click to collapse
Seems pretty easy, please check these videos:
https://www.youtube.com/watch?v=qMIivqu6XJY
https://www.youtube.com/watch?v=v4HZt3Aadsc
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
dodongobongo said:
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
Click to expand...
Click to collapse
Try using a hair dryer on the battery for a minute, but keep moving the hair dryer up and down, to spread the heat all over, this should make the glue soft enough to make it easier to peel the battery off.
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
dodongobongo said:
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
Click to expand...
Click to collapse
Just cracked my phone. :crying:Thanks for the instructions. Before I decide to do this, are any of the adhesives necessary to put the phone back together?
Yes, order some double-tape for cellphones.
Glad I'm not the only one that succeded althought I scrapped the battery in my case .
I followed mostly the same steps but for anyone that want some pictures, I posted them in another thread
http://forum.xda-developers.com/zenfone2/help/q-lcd-replacement-procedure-t3135165
Can asus ze550ml screen will fit to ze550kl model
@Ptselv: probably best to start a new thread rather than hijack one that is several months old.
And to answer your question: No, a ZE550ML screen will not fit a ZE550KL phone. My suggestion: search AliExpress.com for "ze551kl digitizer" and you'll be likely to find what you need.

Battery replacement

Has anyone replaced your battery on tab s2 where you source it?
You can find New Samsung ones on ebay for around 10 English pounds.
Easy job to replace too. Takes around 5 to 10 minutes.
Just loosen the back with a sucker then go round edge with Guitar pick.
Couldn't get back off fully from the Camera, but you can easily get out the battery by flexing the back open gently.
Battery stuck down with a few spots of glue but easily popped out with the guitar pick.
Back popped right back in.... Bit of play on the back so not as water resistant as before. No issue if you use in a case for me.
Beats the 30% wear on the battery after just 14 months.
Forgot to mention, I have the 8 inch version SM-713
I looked around ebay and amazon. Those Chinese man probably selling used ones pretending to be new. Is there any reliable source for really new ones? Thx.
hi anyone here?
optionalmgrr.la said:
hi anyone here?
Click to expand...
Click to collapse
Try Amazon. I just replaced the battery in my T713
I’ve replaced mine twice and sent back three or four batteries.
As far as I can tell, it next to impossible to get a good battery and original is completely unattainable.
So far I have never found a decent battery.
I've asked the local Samsung support a few months ago, it cost, in usd, ~$50, so I sold the tablet instead
Anybody who has done the replacement have any issue getting the back cover back on? I broke a couple of the clips off and can't find a replacement back. I'm hesitant to glue the back together in case this battery takes a dump. I am using double sided tape that came with a screen replacement kit but it is still pretty easy to peel the back off.
hecksagon said:
Anybody who has done the replacement have any issue getting the back cover back on? I broke a couple of the clips off and can't find a replacement back. I'm hesitant to glue the back together in case this battery takes a dump. I am using double sided tape that came with a screen replacement kit but it is still pretty easy to peel the back off.
Click to expand...
Click to collapse
Is this about the 8" version? The 9.7" version needs to have the screen removed, mid-plate unfastened (16 tiny philips screws, including 2 easy to miss ones w flat-black heads).
I've just replaced my battery, the one that was in there was an OEM Samsung but my screen was glued on w black 4mm tape that covered one of the mid-plate screws, so I dunno if this was the original battery.
I replaced mine because I was getting 'storms' of reboots, thought the battery might be the issue (FWIW, still getting the same reboots post-battery-replacement.)
FWIW, I already had a killer suction cup on hand (from a RAM mount setup), these thin pry/cut tools https://www.fixez.com/categories/repair-tools/pry-tools/qianli-stainless-steel-ultrathin-pry-tool made it easy to get the screen off.
I also had an industrial quality heat gun to soften the glue, but that turned out to be unnecessary (you might need one if you start with your tablet cold)
I just changed the Battery on my T813.
It started to do some odd things, like rebooting even though there was plenty of charge or simply discharging to flat from 100% in a few hours without being used.
I got this from amazon https://www.amazon.co.uk/gp/product/B07KSZCDCB/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
it was a breeze to fit, back cover came of really easily after the initial poke around at one of the top corners (camera end)
No screws to undo, no adhesive, once that corner popped up (using the knife seen in pic 1) it was very easy
https://photos.app.goo.gl/H2NJKhsb3t7Supz7A
https://photos.app.goo.gl/8StvHg6WWAJUKEFF9
https://photos.app.goo.gl/7SKB88y8QPBGWtrF8
undo the connector cable, undo the 4 screws, remove
replacement is the reverse, and pop the case back on
Holds charge better, doesn't run out while using and as yet, no random reboots
In 2023 is it possible to buy brand new battery for SM T813?

Categories

Resources