Related
Hello, I have bricked my S8500. I can go to the download menu. The problem is that I can't install properly USB drivers , or maybe it is USB cable that is wrong, the USB cable is from nokia and model is : CA101. Even when the phone was working ok computer couldn't see my wave , and I don't know why... So the problem is that when I go to the Download menu my computer detects all the drivers and everything is alright... And when I hit download I get this.
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
And after Wait reset my computer just didn't recognize my phone anymore, and that's why it has been bricked at the begining. Could anyone please help me? I tried different USB drivers, different PC. Nothing helps :{{{ Please guys, help me.
Maybe it is because my USB cable isn't from original wave, or no?
Nipit said:
Hello, I have bricked my S8500. I can go to the download menu. The problem is that I can't install properly USB drivers , or maybe it is USB cable that is wrong, the USB cable is from nokia and model is : CA101. Even when the phone was working ok computer couldn't see my wave , and I don't know why... So the problem is that when I go to the Download menu my computer detects all the drivers and everything is alright... And when I hit download I get this.
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
And after Wait reset my computer just didn't recognize my phone anymore, and that's why it has been bricked at the begining. Could anyone please help me? I tried different USB drivers, different PC. Nothing helps :{{{ Please guys, help me.
Maybe it is because my USB cable isn't from original wave, or no?
Click to expand...
Click to collapse
I too use Nokia table to flash my samsung wave. If your phone was able to connect to Kies prior to flashing there should be no issues.
When you flash for 1st time you always get that error. Pls try once again and you shd not face any issues.
Datta
No, I wasn't able to connect to kies. I got a USB cable from original xperia x10, still same issue... Can someone tell me what to do? I downloaded a lot of drivers, but maybe there is some special driver? :/
The problem usually goes away for me when flashing from a freshly booted pc, so try restarting one of your computers for flashing and try again.
Have done that too... Any advice? :/
Hello!
First kill all Kies Processes (in the Task Manager)
Second launch Multiloader and try to flash
When it says Serial Error, just do Port Search again, and it should work
That's what I did when I had my Serial Port error ^^
Hope I helped you
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
---------------------------------------------
Just after this message, without quit Multiloader:
Phone on DOWNLOAD MODE try this:
Uncheck Boot, unplug USB Cable from Phone and Plug it again, You will see Download actived in Multiloader, Just clic on DOWNLOAD. And your Flashing will be continued....
----------------------------------------------
Sory For my english.
Still the same **** :{{{ Anymore advices guys?
Darkminus said:
Hello!
First kill all Kies Processes (in the Task Manager)
Second launch Multiloader and try to flash
When it says Serial Error, just do Port Search again, and it should work
That's what I did when I had my Serial Port error ^^
Hope I helped you
Click to expand...
Click to collapse
You didn't understand me very well. The problem is that when I hit download my computer suddenly loses USB connection and shows my phone as unknown device, that is the problem why I bricked my phone. Do anyone knows how to make my pc see my samsung wave?
Nipit said:
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
Click to expand...
Click to collapse
Same thing happened to me. After this, you shouldn't disconnect you wave, but to wait, and click search port again. If there is no port again, tru with different multiloader (mine was v5.65), and there is again same problem, try with another computer with preinstalled USB drivers.
The good thing is that your phone still enters boot mode. If it wasn't the case, then it would be a total brick.
Best regards
Nipit said:
You didn't understand me very well. The problem is that when I hit download my computer suddenly loses USB connection and shows my phone as unknown device, that is the problem why I bricked my phone. Do anyone knows how to make my pc see my samsung wave?
Click to expand...
Click to collapse
No, you didn't understand this flashing process. Most important thing here is to avoid interrupting of connection between computer and phone, even in serial port error. You need to search port again, or to change things that I mentioned above.
You hit download, then bootloader is loaded. It is absolutely normal in this algorithym to reset phone (wait reset). Then our error appears in port error. That is the time when you should click port search again, and when it finds it again (it will) click download button. Thats how it was in my case already 4 times.. Hope I helped.
Best regards
I have told that I reinstalled a lot of drivers and tried different PC's, nothing helps. I tried about 3 or 4 versions of multiloader still same result :/ I don't know what to do anymore... Please any advices? Maybe someone had the same issue?
I don't really know what happened. We switched our cables with my friend again, and I tried to flash with Nokia cable. And everything went okay for the 1 time. No errors, no nothing, no Unknown USB device problem. This is really strange. Thank you for you help friends :}
datta.ca said:
I too use Nokia table to flash my samsung wave. If your phone was able to connect to Kies prior to flashing there should be no issues.
When you flash for 1st time you always get that error. Pls try once again and you shd not face any issues.
Datta
Click to expand...
Click to collapse
i have bricked my s5330 please help
no download mode or even recoverymode please help
I got the same problem too. Windows detects it as Unknown device.
Anyway to fix it? :crying:
[email protected] said:
I got the same problem too. Windows detects it as Unknown device.
Anyway to fix it? :crying:
Click to expand...
Click to collapse
Try to install driver manually from windows driver menu
Just installed "S8500-Driver-V5_02_0_0" now it's working since I wanted to flashback my friend's Wave from Bada2 to v1
[Q] odin says" Can't open the serial(COM) port." and fails to flash recovery.tar
hey,...
i am trying to root my tmobile galaxy S2 and i am in downloading mode...put recovery.tar file in PDA section and when i hit start...nothing happens and after a while i get failed notice and says " Can't open the serial(COM) port." what am i doing wrong.
Did you install the usb drivers first? If not here:
http://www.mediafire.com/?6onrjbyd46j4lhj
that could be the only reason i can think of that odin isn't detecting phone. Also try a different usb port on the computer, and if that doesn't work try a different cable.
uninstall Kies if u have ut because the drivers stick i did and now it works lol
hlimbu00 said:
hey,...
i am trying to root my tmobile galaxy S2 and i am in downloading mode...put recovery.tar file in PDA section and when i hit start...nothing happens and after a while i get failed notice and says " Can't open the serial(COM) port." what am i doing wrong.
Click to expand...
Click to collapse
Darkshado said:
Kies could be interfering with Odin ...
Click to expand...
Click to collapse
I too was having "Can't open the Serial COM". Kies was interfering.
Go into Kies, Tools -> Preferences, unselect "Run Samsung Kies automatically when a device is connected", save the change, close out of Kies, and then restart ODIN 3. Try flashing now.
reinstall drivers with KIES. go to troubleshoot and then you should be good to go after. also check the cable too..
hlimbu00 said:
hey,...
i am trying to root my tmobile galaxy S2 and i am in downloading mode...put recovery.tar file in PDA section and when i hit start...nothing happens and after a while i get failed notice and says " Can't open the serial(COM) port." what am i doing wrong.
Click to expand...
Click to collapse
also sometimes you have to try a different version of odin before it works it happens to me alot. one odin wont work but another does. it's crazy.
Can't open the serial(COM) port Error
hlimbu00 said:
hey,...
i am trying to root my tmobile galaxy S2 and i am in downloading mode...put recovery.tar file in PDA section and when i hit start...nothing happens and after a while i get failed notice and says " Can't open the serial(COM) port." what am i doing wrong.
Click to expand...
Click to collapse
I had the same problem and I fixed it by exiting from Kies software. You might get this new error "Complete(Write) operation failed". Then all you should do is just pulling your battery out and restarting odin and phone. I disables the firewall too, but I don't think the problem was firewall. Anyway mine is working well and I did it.
Hi, I'm also having the same problem. The 'Charging paused...' message kept popping up so I tried to flash a different official rom via odin (I was on official ICS). Unfortunately the flash failed and now when I try to turn on the phone the 'Firmware upgrade encountered an isuue......' message comes up. I tried connenting to kies also but can not to do so. I have hope as i can get into download mode but can't flash a rom. I got halfway once then suddenly it failed again. Your help is much appreciated. Thanks in advance.
Thank You.
phi11yphan said:
I too was having "Can't open the Serial COM". Kies was interfering.
Go into Kies, Tools -> Preferences, unselect "Run Samsung Kies automatically when a device is connected", save the change, close out of Kies, and then restart ODIN 3. Try flashing now.
Click to expand...
Click to collapse
Thank You.
disabled Kies and problem solved
iNeedICS said:
uninstall Kies if u have ut because the drivers stick i did and now it works lol
Click to expand...
Click to collapse
Thanks, this is what was causing me this error. I was close to Hulk-smashing expensive things :laugh:
Re: [Q] odin says" Can't open the serial(COM) port." and fails to flash recovery.tar
NomadRip said:
Thanks, this is what was causing me this error. I was close to Hulk-smashing expensive things :laugh:
Click to expand...
Click to collapse
Haha yea don't resort to hulk smashing things lol just send them to me instead of breaking them I'll delightfully take them off your hands! I'll pm you my address so you can ship xD jkjklolol
Sent from Squishy's Nâ´!
This worked for me
I had the same exact problem (but this was on my Galaxy Y )
What I had was an old version of KIES (~ 2011 ).
Steps :
1) Uninstall the old Kies
2) Download the latest Kies (2013)
I have installed drivers but i cant connect my phone to pc when odin mode is on in phone but i can connect phone to pc when bootloader is on or recovery mode is on . However, when i boot into recovery mode and connect phone to pc and open odin and start it ,it shoes cant open the serial (com) port.
what to do
I'm flashing stock software to phone as my phone got bricked, hurry please help me to unbrick
ttffjioo said:
I have installed drivers but i cant connect my phone to pc when odin mode is on in phone but i can connect phone to pc when bootloader is on or recovery mode is on . However, when i boot into recovery mode and connect phone to pc and open odin and start it ,it shoes cant open the serial (com) port.
what to do
I'm flashing stock software to phone as my phone got bricked, hurry please help me to unbrick
Click to expand...
Click to collapse
The phone needs to be in download mode for Odin. And kies shouldn't be running on your PC. Go to task manager and kill any kies processes.
Download mode on the phone as I remember is power button and volume down.
?
If anyone is using Odin to flash 4.1.2, I found either Odin 3.04 or to be the only ones that worked for me.
Darth said:
The phone needs to be in download mode for Odin. And kies shouldn't be running on your PC. Go to task manager and kill any kies processes.
Download mode on the phone as I remember is power button and volume down.
Click to expand...
Click to collapse
when my phone is on download mode for odin, it cant connect to pc as yellow border line is not showing on odin . I have uninstalled my kies.
tell me what to do
ttffjioo said:
when my phone is on download mode for odin, it cant connect to pc as yellow border line is not showing on odin . I have uninstalled my kies.
tell me what to do
Click to expand...
Click to collapse
Try different Odin versions perhaps. Uninstall Samsung drivers and install the newest kies again to reinstall them. Don't need to uninstall kies , just be sure all its processes are killed in your PC task manager.
There's nothing you can do until your phone and Odin are communicating. Try another cable, try another USB port on your computer. Last, try another computer.
Darth said:
Try different Odin versions perhaps. Uninstall Samsung drivers and install the newest kies again to reinstall them. Don't need to uninstall kies , just be sure all its processes are killed in your PC task manager.
There's nothing you can do until your phone and Odin are communicating. Try another cable, try another USB port on your computer. Last, try another computer.
Click to expand...
Click to collapse
I have downloaded latest kies 3 from official website with latest drivers
I uses cable of my tab 4 (which easily get connects with pc with its cable) to connect my y duos to pc.
Am i doing any thing wrong?
ttffjioo said:
I have downloaded latest kies 3 from official website with latest drivers
I uses cable of my tab 4 (which easily get connects with pc with its cable) to connect my y duos to pc.
Am i doing any thing wrong?
Click to expand...
Click to collapse
Try everything I suggested. Otherwise, I'm out of ideas unfortunately.
I'm curious, what does your phone show as in device manager in pc when connected? Or is it not being seen at all?
And Y Duos? You know this is the Tmobile S2 section, right? ?
Lots of Y Duos bricked talk here as well as other links in this thread to review.
http://forum.xda-developers.com/showthread.php?t=2275057
my galaxy y is brick.
only downloding mode is open.
i think if i flash my phone,it is again good.
but when i connect my phone in pc ,pc say usb driver not recognized.
but i install samsung usb driver.
i change my usb cable,also try in frnds pc,
but i cant connect my phone.
for these reason i cant flash my phone!
if anyone help me!
Imtiaz369 said:
my galaxy y is brick.
only downloding mode is open.
i think if i flash my phone,it is again good.
but when i connect my phone in pc ,pc say usb driver not recognized.
but i install samsung usb driver.
i change my usb cable,also try in frnds pc,
but i cant connect my phone.
for these reason i cant flash my phone!
if anyone help me!
Click to expand...
Click to collapse
Try to first open the phone in download mode and then connect the usb driver. Try downloading odin from another site. And pls post in FAQ.
Sent from heaven!
start kies,and then use odin,when both not worx reinstall and try again,it must work
Its real easy just try to connect the phone to ur pc without download mode the phn starts to the charging mode and u will observe tht ur drivers get installed after they r installed use odin normally happy flashing:thumbup:
Sent from my GT-S5360 using xda premium
Remove kies/sam driver and reinstall then try sure its working ..... Always close kies ..fflash mode.....
Sent from my GT-S6102 using xda premium
1. Fully Uninstall all Kies and reinstall it.
2. If your battry is low, switch off your mobile and charger your mobile
3. After complted charging, go to download mode (Powr + home + down arrow)
4. Open KIES then connect your mobile in download mode, now it will detected automatically.
5. Open ODIN check COM port is in yellow color, if it is in yellow color, close your KIES.
6. After completely closing of KIES, select your firmware version in ODIEN then flash it.
All the Best .........
try Odin from other site
change your USB cable
Imtiaz369 said:
my galaxy y is brick.
only downloding mode is open.
i think if i flash my phone,it is again good.
but when i connect my phone in pc ,pc say usb driver not recognized.
but i install samsung usb driver.
i change my usb cable,also try in frnds pc,
but i cant connect my phone.
for these reason i cant flash my phone!
if anyone help me!
Click to expand...
Click to collapse
dont panic,first of all remove sim card and sd card
after that start with Odin
if you still can use download mod then its ok
inform me
everything you need is here thanx to Ronnieryan
http://forum.xda-developers.com/showthread.php?t=1675474&page=2
Troubleshooting Instructions
Imtiaz369 said:
my galaxy y is brick.
only downloding mode is open.
i think if i flash my phone,it is again good.
but when i connect my phone in pc ,pc say usb driver not recognized.
but i install samsung usb driver.
i change my usb cable,also try in frnds pc,
but i cant connect my phone.
for these reason i cant flash my phone!
if anyone help me!
Click to expand...
Click to collapse
1.Try to redownload the firmware that you've flashes and flash it again if it will help.
Troubleshooting Instructions:
"USB Driver Not Recognized" Problem ?
Well here's my list of troubleshooting instructions:
1.If your USB Driver is not recognized , Open Kies on your PC/Laptop then click "Troublelshoot connection problem" button , It will reinstall the USB Driver named "SAMSUNG USB Driver for Mobile Phones" . Wait until it finish .
2.Uninstall Kies and the USB Driver named "SAMSUNG USB Driver for Mobile Phones" on Add and remove programs on Control panel , Then after you install Kies again then do the directions on Step 1 installing your USB Driver.
3.Try Redownloading Odin v 1.85 , Click on my attachment to download.
4.Make sure your Kies is up to date.
5.Make sure that your battery is 100 % fully charged
6.Remove your SIM Card before flashing , That could interrupt the flashing process.
7.Press Ctrl+Alt+Delete and go to Processes and terminate the process named "KiesHelper.exe" and "KiesTrayAgent.exe" and if you're using ADB then terminate the process named "adb.exe" ( Im not sure if adb.exe is the correct name of ADB process,Correct me if im wrong)
8.Make sure before you press the "Start" button on Odin you should Notice these two thing before pressing the Start button : ID:COM and make sure you have got the "Added!!!" word on the box (Where you can see if flashing has successful ex. Success 1/0 Failed
Hi all,
I really need some help here with my Samsung Galaxy i747M which i recently wipe/factory data reset and wiped the cache. The phone booted fine after and i went through all the setup steps, then the problem begins. I am unable to see a background then the phone reboots and ends up in a bootloop. I am able to access download mode and recovery mode but my PC is not able to pick up the phone in download mode. I tried switching the usb cables and everything and still nothing.
My question is, is there any way to flash a new firmware via recovery mode or at least a custom rom and/or CWM through recovery mode. I am not able to pick up the phone through Odin.
Please help!!
You mean Odin does not detect the phone when it is connected in download mode? You're running the most up-to-date s3 drivers and Odin 3.07 or 3.09?
What bootloader is on your phone?
audit13 said:
You mean Odin does not detect the phone when it is connected in download mode? You're running the most up-to-date s3 drivers and Odin 3.07 or 3.09?
What bootloader is on your phone?
Click to expand...
Click to collapse
my pc does not acknowledge the phone's connection at all!! i have the stock bootloader. the phone is not rooted either
Does your phone have a custom recovery? You mean the phone is not listed in Device Manager, Odin, or both?
audit13 said:
Does your phone have a custom recovery? You mean the phone is not listed in Device Manager, Odin, or both?
Click to expand...
Click to collapse
no the phone does not have a custom recovery, i wanted to know if there is anyway other than odin to flash in a custom recovery using the stock recovery. device manager or odin does not pick up the phone for whatever unknown reason. what can i do??
You can't flash a custom recovery through the stock recovery. The easiest way would have been to do it via Odin.
Are you running a Mac or Windows machine? What OS? Does the phone charge when it's connected to the computer?
audit13 said:
You can't flash a custom recovery through the stock recovery. The easiest way would have been to do it via Odin.
Are you running a Mac or Windows machine? What OS? Does the phone charge when it's connected to the computer?
Click to expand...
Click to collapse
I am running on a windows machine with windows 7. Yes the phone charges when connected to a PC but just not picking up as a device. Is there no other option?
narell said:
I am running on a windows machine with windows 7. Yes the phone charges when connected to a PC but just not picking up as a device. Is there no other option?
Click to expand...
Click to collapse
You tried a different computer too? Are there any unknown devices in device manager when you connect the phone? You tried all of your USB 2.0 ports? If you did all of this, it's possible the USB port on the phone has malfunctioned.
You could try loading a custom recovery via fastboot.
audit13 said:
You tried a different computer too? Are there any unknown devices in device manager when you connect the phone? You tried all of your USB 2.0 ports? If you did all of this, it's possible the USB port on the phone has malfunctioned.
You could try loading a custom recovery via fastboot.
Click to expand...
Click to collapse
fastboot...is this the same as adb sideload? doesnt fastboot require a connection to a pc to use command prompt? i could be wrong...i tried it on other pc's as well and swapped between usb ports..
narell said:
fastboot...is this the same as adb sideload? doesnt fastboot require a connection to a pc to use command prompt? i could be wrong...i tried it on other pc's as well and swapped between usb ports..
Click to expand...
Click to collapse
So there are no unknown devices in device manager on any computer with any USB cables? If that's the case, maybe the phone's USB port is defective.
Yes, ADB/fastboot requires a working USB connection but the drivers are different from when you connect the phone after it has booted to its desktop.
audit13 said:
So there are no unknown devices in device manager on any computer with any USB cables? If that's the case, maybe the phone's USB port is defective.
Yes, ADB/fastboot requires a working USB connection but the drivers are different from when you connect the phone after it has booted to its desktop.
Click to expand...
Click to collapse
i checked device manager, nothing...thanks alot for your help i will see if adb/fastboot works...will let u know!!
Hi guys !
I rooted my phone and then tried to setup some roms. But when I try to go in the download mode, it says "Downloading... Do not turn off the target" but on my computer, it cannot recognize the usb. I setup the usb drivers, tried another ports and there is no problem about my usb cable. It works normally, but whenever I go in the download mode, this thing happens and I cant continue to Odin. Does anyone know anything about that ?
burhannde said:
Hi guys !
I rooted my phone and then tried to setup some roms. But when I try to go in the download mode, it says "Downloading... Do not turn off the target" but on my computer, it cannot recognize the usb. I setup the usb drivers, tried another ports and there is no problem about my usb cable. It works normally, but whenever I go in the download mode, this thing happens and I cant continue to Odin. Does anyone know anything about that ?
Click to expand...
Click to collapse
When you install custom ROMs, you need to go to recovery mode ( Volulme Up + Power + Home ), not to download mode
MayB4ck said:
When you install custom ROMs, you need to go to recovery mode ( Volulme Up + Power + Home ), not to download mode
Click to expand...
Click to collapse
I am trying to setup ClockWorkMode Recovery. That's why I go in to download mode
burhannde said:
I am trying to setup ClockWorkMode Recovery. That's why I go in to download mode
Click to expand...
Click to collapse
You can install it easily if your phone is rooted just
-put the downloaded recovery.img in /mnt/sdcard
-download & install "Terminal Emulator" in play store
-open it then type "su" and click enter
-allow root access..
-then type "dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p13" then click enter
-then some text will show in bottom
-exit terminal..
check the recovery by turning off the device then turn on with volume up botton, home button, and power button pressed together..
until "Galaxy W" screen shows up, release the power button only.. then you will enter CWM
MayB4ck said:
You can install it easily if your phone is rooted just
have the same problem + a bootloop...
what should i do?!
the phone is rooted
windows cant detect it when in download mode (wich i need to connect with odin)
now i cant even get the stock rom back on my phone
Click to expand...
Click to collapse
zekare said:
MayB4ck said:
You can install it easily if your phone is rooted just
have the same problem + a bootloop...
what should i do?!
the phone is rooted
windows cant detect it when in download mode (wich i need to connect with odin)
now i cant even get the stock rom back on my phone
Click to expand...
Click to collapse
What version of windows are you running, it couldn't work on windows 8 and 8.1 so i installed 7 and all the drivers for the phone and it works, i dont have the phone now but i do beleive that will, anyway... if you have bootloop that means you are still able to pass the bootloader screen right?? then try to go to recovery and flash roms from there, having an sd card would help transfering roms from pc directly to phone....
Reply again if you need some assistance.. I'm not online very often
Click to expand...
Click to collapse
MayB4ck said:
zekare said:
What version of windows are you running, it couldn't work on windows 8 and 8.1 so i installed 7 and all the drivers for the phone and it works, i dont have the phone now but i do beleive that will, anyway... if you have bootloop that means you are still able to pass the bootloader screen right?? then try to go to recovery and flash roms from there, having an sd card would help transfering roms from pc directly to phone....
Reply again if you need some assistance.. I'm not online very often
Click to expand...
Click to collapse
i have windows 10 pro.
yes, first the samsung logo apears then the galaxy W logo.
it stays 1 or 2 minutes on this galaxy W logo screen then it reboots.
is it even possible to flash it with the original bootloader from a sd card?
and would the original bootloader detect this type of image (.tar.md5) ?
Thank you for reply
Click to expand...
Click to collapse
zekare said:
MayB4ck said:
i have windows 10 pro.
yes, first the samsung logo apears then the galaxy W logo.
it stays 1 or 2 minutes on this galaxy W logo screen then it reboots.
is it even possible to flash it with the original bootloader from a sd card?
and would the original bootloader detect this type of image (.tar.md5) ?
Thank you for reply
Click to expand...
Click to collapse
You can try putting any custom rom and flash from a custom recovery if you can access it, if not download the stock rom and get a windows 7 pc. make sure you install all the samsung drivers ( kies should do the job ) and try flashing it from odin
Click to expand...
Click to collapse
MayB4ck said:
zekare said:
You can try putting any custom rom and flash from a custom recovery if you can access it, if not download the stock rom and get a windows 7 pc. make sure you install all the samsung drivers ( kies should do the job ) and try flashing it from odin
Click to expand...
Click to collapse
so is win10 the problem ?
i tried 100 things to connect pc with the phone in downloadmode. nothing workd.
if i can find a win 7 pc i will try it. but is there any other way?
i also tried adb on windows it also not works.
then i did a ubuntu usb drive and tried to do it with heimdall but im not a coder. it was very confusing.
at least i was able to detect the device but thats it.
well, anyway thanks alot for your help.
i will try it on a win7 pc
Click to expand...
Click to collapse
Download mode Windows 8.1 10
To connect your phone in download mode on Windows 8.1 and 10 you need to apply this registry file (in my attached zip file).
Mirror Link
It happens for most old phones.
More Info: https://blogs.msdn.microsoft.com/us...ows-8-0-but-fail-on-windows-8-1-with-code-43/
Also note Odin3 (the one which is used for newer phones) doesn't work for Galaxy W! (Use Odin Multi Downloader.)
--------
Update: It seems that this registry key isn't needed. Make sure to connect the USB cable after downloading... screen appears. If it wasn't recognized try disconnect and reconnecting the USB cable or try other USB ports on PC till it gets recognized.
mat1371 said:
To connect your phone in download mode on Windows 8.1 and 10 you need to apply this registry file (in my attached zip file).
Mirror Link
It happens for most old phones.
More Info: https://blogs.msdn.microsoft.com/us...ows-8-0-but-fail-on-windows-8-1-with-code-43/
Also note Odin3 (the one which is used for newer phones) doesn't work for Galaxy W! (Use Odin Multi Downloader.)
Click to expand...
Click to collapse
still doesn't work for me, can you please post the drivers you are using ?
If you see the USB device is not recognized error it's not a driver issue.
Windows automatically downloads the drivers through Windows Update. BTW here are the drivers:
SAMSUNG.zip - 13.5 MB
deleted
mat1371 said:
Download mode Windows 8.1 10
To connect your phone in download mode on Windows 8.1 and 10 you need to apply this registry file (in my attached zip file).
Mirror Link
It happens for most old phones.
More Info: https://blogs.msdn.microsoft.com/us...ows-8-0-but-fail-on-windows-8-1-with-code-43/
Also note Odin3 (the one which is used for newer phones) doesn't work for Galaxy W! (Use Odin Multi Downloader.)
--------
Update: It seems that this registry key isn't needed. Make sure to connect the USB cable after downloading... screen appears. If it wasn't recognized try disconnect and reconnecting the USB cable or try other USB ports on PC till it gets recognized.
Click to expand...
Click to collapse
it works. thank u so much...