Develop Bugs

Is it possible to go back to stock without S-Off?

I unlocked the bootloader, installed TWRP and then installed a rooted version of stock OS. Can I go back to completely stock without S-Off, or is it absolutely required that I pay the $25 to go back to stock?

Looking for the same option
Wish I had a solution for you, but I don't see one. Looks like we're stuck with either an S-On or a $25 charge

I've tried to look for an answer as well. The latest RUU from my carrier is only 1.32, and in the event that I need to service my phone, I'm not sure if stock system + TWRP is good enough for 'stock'.
My phone scared me today because random white, vertical lines appeared on the screen, but they didn't show up when I rebooted into the power + vol. down menu. They slowly disappeared, but it was definitely worrying. I'm afraid the display will go bad soon.

This is the best option I've found so far. Going to give it a try tomorrow, unless anyone has suggestions.

Unfortunately I'm not having a lot of luck. Using the files on that site, and also tried the "1.32.531.33 SystemDump" from XDA, but in both cases as soon as it starts up it says "EasyShare stopped responding" and "System UI stopped responding" before even doing the setup wizard. Tried wiping the cache, and redownloading the files but still the same errors every time. Not sure what I'm missing...

Okay, I finally got it back to stock using these instructions and the "fastboot/sd card" RUU zips from here. Everything appears to be working, and back at stock without needing S-OFF!

Cabrill said:
Okay, I finally got it back to stock using these instructions and the "fastboot/sd card" RUU zips from here. Everything appears to be working, and back at stock without needing S-OFF!
Click to expand...
Click to collapse
All that you needed was an unlocked bootloader to load a Stock RUU.

Cabrill said:
Okay, I finally got it back to stock using these instructions and the "fastboot/sd card" RUU zips from here. Everything appears to be working, and back at stock without needing S-OFF!
Click to expand...
Click to collapse
can you guide me how you did it without turning s off?

Harris Aamir said:
can you guide me how you did it without turning s off?
Click to expand...
Click to collapse
The thread is very old, but I can help you.
First we need to know more about your device, so boot in download mode and do "fastboot getvar all" then post the result here(remove imei,sn)
For this you need adb and fastboot, if you don't have I recommend you Minimal ADB & Fastboot, and make sure you have htc drivers installed.

lucyr03 said:
The thread is very old, but I can help you.
First we need to know more about your device, so boot in download mode and do "fastboot getvar all" then post the result here(remove imei,sn)
For this you need adb and fastboot, if you don't have I recommend you Minimal ADB & Fastboot, and make sure you have htc drivers installed.
Click to expand...
Click to collapse
kernel: lk
(bootloader) product: htc_himawhl
(bootloader) version: 1.0
(bootloader) version-main: 3.41.651.4
(bootloader) boot-mode: download
(bootloader) version-baseband: [email protected]
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA20000
(bootloader) cid: SPCS_001

Harris Aamir said:
kernel: lk
(bootloader) product: htc_himawhl
(bootloader) version: 1.0
(bootloader) version-main: 3.41.651.4
(bootloader) boot-mode: download
(bootloader) version-baseband: [email protected]
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA20000
(bootloader) cid: SPCS_001
Click to expand...
Click to collapse
This is the ruu: https://androidfilehost.com/?fid=673368273298941856
Rename it to 0PJAIMG.zip and put in root of your fat32 formatted sdcard, then boot in download and follow instructions.

lucyr03 said:
This is the ruu: https://androidfilehost.com/?fid=673368273298941856
Rename it to 0PJAIMG.zip and put in root of your fat32 formatted sdcard, then boot in download and follow instructions.
Click to expand...
Click to collapse
i want the android 7 ruu

Harris Aamir said:
i want the android 7 ruu
Click to expand...
Click to collapse
You need to flash marshmallow, then update with ota.

lucyr03 said:
You need to flash marshmallow, then update with ota.
Click to expand...
Click to collapse
cant i flash noughat update?

Harris Aamir said:
cant i flash noughat update?
Click to expand...
Click to collapse
You can't just flash nougat if you're s-on, you need to flash a ruu that match to your current firmware version, then you can update via ota to the latest nougat.

lucyr03 said:
You can't just flash nougat if you're s-on, you need to flash a ruu that match to your current firmware version, then you can update via ota to the latest nougat.
Click to expand...
Click to collapse
hi, sorry, I'm in a similar situation too. I'm s-on and I would like to return completely stock. Can I do it simply by flashing the ruu of my firmware? If I post the data of my phone can you kindly help me find the ruu? Thanks

Daniel Gigliotti said:
hi, sorry, I'm in a similar situation too. I'm s-on and I would like to return completely stock. Can I do it simply by flashing the ruu of my firmware? If I post the data of my phone can you kindly help me find the ruu? Thanks
Click to expand...
Click to collapse
Yeah, post the getvar all

lucyr03 said:
Yeah, post the getvar all
Click to expand...
Click to collapse
(bootloader) kernel: lk
(bootloader) product: htc_himauhl
(bootloader) version: 1.0
(bootloader) current-slot:
(bootloader) version-main: 4.28.401.3
(bootloader) boot-mode: download
(bootloader) version-baseband: 01.01_U114401011_117.00.61117G_2_F
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA10000
(bootloader) cid: HTC__031

Daniel Gigliotti said:
(bootloader) kernel: lk
(bootloader) product: htc_himauhl
(bootloader) version: 1.0
(bootloader) current-slot:
(bootloader) version-main: 4.28.401.3
(bootloader) boot-mode: download
(bootloader) version-baseband: 01.01_U114401011_117.00.61117G_2_F
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA10000
(bootloader) cid: HTC__031
Click to expand...
Click to collapse
The ruu: https://androidfilehost.com/?fid=961840155545567615
Same instructions as before to flash.
Sent from my HTC One using XDA Labs

M8 Bricked while updating to Marshmallow.

Hi,
The other day i've tried to update my M8 to marshmallow via OTA and my device get bricked . . .
It is stucked on Android Recovery, and have tried everything. Ruu's, factory reset . . . everything. Ruu always gives me back error 155.
Don't know what else to do. It is new, but I think the people that sold it to me have changed things like CID and it have S-OFF.
I'll post the "fastboot getvar all" command results:
E:\Minimal ADB and Fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.12G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.12.401.4
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei: ---------------------
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B10000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 76df2b54
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
Can someone help me? :crying: Thanks!

I am having the same problem!! I installed the official update via the system update, installed then at the end it told me there is a problem with the OTA thing and that is it. Since then my device is bricked and I'm in between the recovery menu and the bootloader.
I don't wanna root my device and didn't try it. This sucks. I wish I can rollback this mess to Lollipop.

Moe88Saber said:
I am having the same problem!! I installed the official update via the system update, installed then at the end it told me there is a problem with the OTA thing and that is it. Since then my device is bricked and I'm in between the recovery menu and the bootloader.
I don't wanna root my device and didn't try it. This sucks. I wish I can rollback this mess to Lollipop.
Click to expand...
Click to collapse
I had a similar issue, bricked my HTC ONE M8 by updating through OTA.
But I got it fixed by flashing RUU through htc_fastboot.exe, it took a while but was effective.
In your case, if you need to find your right CID, first get your mid number and check if you can find a right CID to your MID, then write it through fastboot. Hope it can help you.
If you will need a detailed how to, let me know

azbtaurus said:
I had a similar issue, bricked my HTC ONE M8 by updating through OTA.
But I got it fixed by flashing RUU through htc_fastboot.exe, it took a while but was effective.
In your case, if you need to find your right CID, first get your mid number and check if you can find a right CID to your MID, then write it through fastboot. Hope it can help you.
If you will need a detailed how to, let me know
Click to expand...
Click to collapse
My CID is 11111111, it says so in the bootloader. Can you provide links on where to get the RUU and the flashing app? Thanks
The bootloader says LOCKED yet my device is the international variant. Is it related or does it mean that my bootloader is locked?

ramajo17 said:
Hi,
The other day i've tried to update my M8 to marshmallow via OTA and my device get bricked . . .
It is stucked on Android Recovery, and have tried everything. Ruu's, factory reset . . . everything. Ruu always gives me back error 155.
Don't know what else to do. It is new, but I think the people that sold it to me have changed things like CID and it have S-OFF.
I'll post the "fastboot getvar all" command results:
E:\Minimal ADB and Fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.12G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.12.401.4
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: FA44WWM07312
(bootloader) imei: ---------------------
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B10000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 76df2b54
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
Can someone help me? :crying: Thanks!
Click to expand...
Click to collapse
Hey, I've made a simple research and found that your serial number belongs to HTC ONE M8 Taiwan version, so first you need to change your MID to 0P6B150 (optional but strongly advised for applaying offical updates) and then the CID to CHT__601 (Taiwan).
Only after this you need to find the right RUU and flash it, or use RUU.zip and flash it through htc_fastboot.exe
Hope it will be helpfull
---------- Post added at 09:52 AM ---------- Previous post was at 09:48 AM ----------
Moe88Saber said:
My CID is 11111111, it says so in the bootloader. Can you provide links on where to get the RUU and the flashing app? Thanks
The bootloader says LOCKED yet my device is the international variant. Is it related or does it mean that my bootloader is locked?
Click to expand...
Click to collapse
Send me your detailed phone information as it was shown in the first post of the thread so I can tell you how to change you CID and other identification numbers that in the end will let you apply the update
Having the original CID is very important, cuz your bootloader was relocked? otherwise they could've not changed you CID/
Check your serial information go to HTC Warranty Check - Lookup
this tell you right region information of your phone so you can easily find right CID and MID numbers of your phone

azbtaurus said:
Send me your detailed phone information
Click to expand...
Click to collapse
Can you walk me through it? When I connect my device to my laptop, it shows nothing. the HTC sync app fails to detect my phone as well.
But my bootloader detects it. It goes from FASTBOOT to FASTBOOT USB

azbtaurus said:
Hey, I've made a simple research and found that your serial number belongs to HTC ONE M8 Taiwan version, so first you need to change your MID to 0P6B150 (optional but strongly advised for applaying offical updates) and then the CID to CHT__601 (Taiwan).
Click to expand...
Click to collapse
That is wrong .. you need to see the CID/MID not the serial no.
He can flash the 6.12.401.4 RUU zip
---------- Post added at 01:40 PM ---------- Previous post was at 01:35 PM ----------
ramajo17 said:
Hi,
The other day i've tried to update my M8 to marshmallow via OTA and my device get bricked . . .
It is stucked on Android Recovery, and have tried everything. Ruu's, factory reset . . . everything. Ruu always gives me back error 155.
Don't know what else to do. It is new, but I think the people that sold it to me have changed things like CID and it have S-OFF.
I'll post the "fastboot getvar all" command results:
E:\Minimal ADB and Fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.12G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.12.401.4
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei: ---------------------
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul_ca
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B10000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 76df2b54
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
Can someone help me? :crying: Thanks!
Click to expand...
Click to collapse
1. - remove the serial no. in your above post.
2. - Is the bootloader LOCKED or RELOCKED ? If it is UNLOCKED, relock it with command fastboot oem lock
3. - follow this : http://forum.xda-developers.com/showpost.php?p=64926362&postcount=4 for the driver part
and this : http://forum.xda-developers.com/showpost.php?p=64926626&postcount=6 for the RUU part

Moe88Saber said:
Can you walk me through it? When I connect my device to my laptop, it shows nothing. the HTC sync app fails to detect my phone as well.
But my bootloader detects it. It goes from FASTBOOT to FASTBOOT USB
Click to expand...
Click to collapse
1 - see the links in the end of #7 post? Go there and first get the drivers and adb-fastboot tools
once you get try command fastboot getvar all this will show you the detailed information of your device
2 - once done get HTC ONE M8 all in one tool kit, it would be easier for you to use instead typing commands all the time
3 - unlock your bootloader by following the instructions on the program listed above
4 - search for right CID number of your phone and write it by using command fastboot oem writecid (YOUR CID)
5 - relock bootloader
6 - flash the right RUU (check if it is right for your original new CID)
Keep in mind that I've done this on my own devices, and I don't take any responsibility in case if you get your device bricked

ckpv5 said:
That is wrong .. you need to see the CID/MID not the serial no.
He can flash the 6.12.401.4 RUU zip
---------- Post added at 01:40 PM ---------- Previous post was at 01:35 PM ----------
1. - remove the serial no. in your above post.
2. - Is the bootloader LOCKED or RELOCKED ? If it is UNLOCKED, relock it with command fastboot oem lock
3. - follow this : http://forum.xda-developers.com/showpost.php?p=64926362&postcount=4 for the driver part
and this : http://forum.xda-developers.com/showpost.php?p=64926626&postcount=6 for the RUU part
Click to expand...
Click to collapse
I'm not the OP but I am experiencing the same issue. anyway...my bootloader is locked and it is connected to the ADB, getvar shows me some stats. I'm now downloading the RUU and will flash it afterwards. Thanks for your help.

Moe88Saber said:
I'm not the OP but I am experiencing the same issue. anyway...my bootloader is locked and it is connected to the ADB, getvar shows me some stats. I'm now downloading the RUU and will flash it afterwards. Thanks for your help.
Click to expand...
Click to collapse
You cannot simply flash the RUU .. the first question is .. is the RUU the right one for your device ?
You have SUperCID as you mentioned above .. what about the MID ?
Is it 0P6B10000 ? If yes .. then go ahead

ckpv5 said:
You cannot simply flash the RUU .. the first question is .. is the RUU the right one for your device ?
You have SUperCID as you mentioned above .. what about the MID ?
Is it 0P6B10000 ? If yes .. then go ahead
Click to expand...
Click to collapse
Sir, If you mean the modelid, then yes, it is 0P6B10000 and cidnum is 11111111
Should I go ahead?

Moe88Saber said:
Sir, If you mean the modelid, then yes, it is 0P6B10000 and cidnum is 11111111
Should I go ahead?
Click to expand...
Click to collapse
Yes.. sure

ckpv5 said:
That is wrong .. you need to see the CID/MID not the serial no.
He can flash the 6.12.401.4 RUU zip
---------- Post added at 01:40 PM ---------- Previous post was at 01:35 PM ----------
1. - remove the serial no. in your above post.
2. - Is the bootloader LOCKED or RELOCKED ? If it is UNLOCKED, relock it with command fastboot oem lock
3. - follow this : http://forum.xda-developers.com/showpost.php?p=64926362&postcount=4 for the driver part
and this : http://forum.xda-developers.com/showpost.php?p=64926626&postcount=6 for the RUU part
Click to expand...
Click to collapse
Ok I'm downloading the RUU. I've tried to apply this RUU from computer but not worked, I hope it works with fastboot!
I'll tell you once is done, thanks!
Update info:
It gets stuck in "sending 'zip'... <53965 KB>
I've waited 20 minutes and nothing happens.

ckpv5 said:
yes.. Sure
Click to expand...
Click to collapse
yes!!! It lives! You are one magnificent human being! I am forever in your debt!:d:d
thank you thank you thank you

ramajo17 said:
Ok I'm downloading the RUU. I've tried to apply this RUU from computer but not worked, I hope it works with fastboot!
I'll tell you once is done, thanks!
Update info:
It gets stuck in "sending 'zip'... <53965 KB>
I've waited 20 minutes and nothing happens.
Click to expand...
Click to collapse
Have you install the fastboot/adb that linked above ?
Have you updated the HTC USB drivers, also linked above ?
Try with a Windows PC USB2.0

ckpv5 said:
Have you install the fastboot/adb that linked above ?
Have you updated the HTC USB drivers, also linked above ?
Try with a Windows PC USB2.0
Click to expand...
Click to collapse
Yes both things. I'll try to download the RUU again because when I try to unzip it on my PC it says that the file is corrupted.
Can be that the problem?

ramajo17 said:
Yes both things. I'll try to download the RUU again because when I try to unzip it on my PC it says that the file is corrupted.
Can be that the problem?
Click to expand...
Click to collapse
You can't extract/unzip an encrypted HTC RUU zip.
You never reply to my first question .. is your bootloader LOCKED, RELOCKED or UNLOCKED ?
If it is UNLOCKED .. I can suggest another method .. restore a TWRP backup.
If you have installed both adb/fastboot and latest HTC USB driver (and uninstall HTC Sync Manager) I don't see a reason why it cannot work for you when it worked for the other guy (post #14)
Do you have a microSD card ? You can do it different way.

ckpv5 said:
You can't extract/unzip an encrypted HTC RUU zip.
You never reply to my first question .. is your bootloader LOCKED, RELOCKED or UNLOCKED ?
If it is UNLOCKED .. I can suggest another method .. restore a TWRP backup.
If you have installed both adb/fastboot and latest HTC USB driver (and uninstall HTC Sync Manager) I don't see a reason why it cannot work for you when it worked for the other guy (post #14)
Do you have a microSD card ? You can do it different way.
Click to expand...
Click to collapse
Sorry, it is RELOCKED.
I'll try to do all from 0 again. If it does not work we can UNLOCK it and try the TWRP method you say?
Yes I do have an SD card in my phone, but my PC doesn't detect it and have no SD adapter. I've heard that there's some fastboot command "push" or something like that to put the RUU on it but don't know how it works.
Thanks for your time, I'm desperate. . .

You need to unlock bootloader to go with TWRP method.
Just try again ... with a Windows PC with USB2.0 (many people report USB3.0 is a hit and miss)
Make sure the HTC Sync manager is uninstalled after you install the driver.

ckpv5 said:
You need to unlock bootloader to go with TWRP method.
Just try again ... with a Windows PC with USB2.0 (many people report USB3.0 is a hit and miss)
Make sure the HTC Sync manager is uninstalled after you install the driver.
Click to expand...
Click to collapse
Can't believe it was de USB . . . Now is doing things, let's see
Update:
IT IS ALIVE!! The problem was de USB . . I was using the official one but didn't work.
Really big thanks!!

Soft Bricked HK M9 - OS-3.42.708.3

need your help guys
i really dont know how the phone got to the position where it says that the software modified, as far as i know, no one tried to flash any 3rd party roms.
current status:
software: modified
Locked
S-on
whats available:
bootloader, recovery, download modes are available, phone is recognized via fastboot, but not much info there
fastboot getvar all
(bootloader) kernel: lk
(bootloader) product: htc_himauhl
(bootloader) version: 1.0
(bootloader) imei: 35xxxxxxxxxxxxx350
(bootloader) version-main: 3.42.708.3
(bootloader) boot-mode: download
(bootloader) version-baseband: 01.01_U11440801_97.04.60111G_F
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA10000
(bootloader) cid: HTC__622
what's impossible:
*can't unlock officially - as i don't have working system to enable oem unlock at dev options
*can't flash twrp backup as i cant flash different recovery - s-on
*can't flash any ota update with working system.img - s-on
*can't flash RUU zip as there isn't one with my current version and can't downgrade - s-on
any suggestions whats available for me to fix it?

How did it end up in that state?.
Beamed in by telepathy.

im not sure, the device belong to a friend, its not mine, im just trying to help out

It looks like it got "killed" by trying to set back "unlocked" and "S-OFF" to "locked" and "S-ON". Your only hope is llabtoofer's RUU service because as you already found out there is no publicly available RUU for that phone. Direct links can be found in my sticky thread in the general section or in my google sheet.
Sent from my HTC One M9 using XDA Labs

sh33z0r said:
im not sure, the device belong to a friend, its not mine, im just trying to help out
Click to expand...
Click to collapse
I can help you with this RUU....

shivasrage said:
I can help you with this RUU....
Click to expand...
Click to collapse
Have same problem too. Any help would be much appreciated.

same problem here

No roms will boot or function properly

I got my Sprint 10 like two weeks ago roughly and used Sunshine to get S-off and installed the latest TWRP. I have tried CM, Leedroid, ICE, Viper, and Bad Boyz and the only one that would ever even start up properly was Bad Boyz and it didn't have a functioning home button which is a complete deal breaker so...yeah. All other roms, for the most part will just not boot. White screen with HTC on it for an hour+ and nothing happens. ICE would boot, and start the activation wizard but the instant the PRL updates and I hit OK the phone reboots and goes through activation again but just stays on that screen and refuses to activate even though I can see I have an LTE data signal.
I tried completely starting over four times, three times by flashing the earliest RUU version and going through all OTA updates then doing it all over again minus the Sunshine s-off because I've been s-off the entire time. One time by just flashing a later RUU to skip the OTAs. Nothing works. I don't get it. I'm CLEARLY doing something very wrong and it's incredibly frustrating. I've tried formatting, not wiping, data and of course nothing. I said I'd give up but I reeeaallly would like to use ICE or Leedroid.

You are most likely on Marshmallow firmware and on an outdated TWRP (maybe).
Update your firmware to Nougat, then flash the romm.
The firmware/rom missmatch causes the broken fingerprint too.
HFA and setting PRL works on our rom.

j to the 4n said:
You are most likely on Marshmallow firmware and on an outdated TWRP (maybe).
Update your firmware to Nougat, then flash the romm.
The firmware/rom missmatch causes the broken fingerprint too.
HFA and setting PRL works on our rom.
Click to expand...
Click to collapse
While originally that didn't make sense to me, I did it anyway. At least I thought I did. Does accepting all OTA updates include firmware? Because I did do that, and actually now Bad Boyz won't even boot so I'm stuck with stock nougat
Edit: TWRP is the latest 3.1.01 or whatever the number is, I forget exactly but I checked and even redownloaded it from their site.

Skeezixmccat said:
While originally that didn't make sense to me, I did it anyway. At least I thought I did. Does accepting all OTA updates include firmware? Because I did do that, and actually now Bad Boyz won't even boot so I'm stuck with stock nougat
Edit: TWRP is the latest 3.1.01 or whatever the number is, I forget exactly but I checked and even redownloaded it from their site.
Click to expand...
Click to collapse
post a fastboot getvar all from download mode, and try to use TWRP 3.1.0.0

j to the 4n said:
post a fastboot getvar all from download mode, and try to use TWRP 3.1.0.0
Click to expand...
Click to collapse
Code:
(bootloader) kernel: lk
(bootloader) product: htc_pmewhl
(bootloader) version: 1.0
(bootloader) max-download-size: 1579200000
(bootloader) serialno:
(bootloader) current-slot:
(bootloader) imei:
(bootloader) version-main: 2.42.651.6
(bootloader) boot-mode: download
(bootloader) version-baseband: [email protected]
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 2PS640000
(bootloader) cid: SPCS_001
all:
finished. total time: 0.010s
I had to work the last few days and in general wanted to take a little break from this headache. Are there known issues with the latest TWRP? I'll downgrade to the flat 3.1 version later on tonight.

Skeezixmccat said:
Code:
(bootloader) kernel: lk
(bootloader) product: htc_pmewhl
(bootloader) version: 1.0
(bootloader) max-download-size: 1579200000
(bootloader) serialno:
(bootloader) current-slot:
(bootloader) imei:
(bootloader) version-main: 2.42.651.6
(bootloader) boot-mode: download
(bootloader) version-baseband: [email protected]
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 2PS640000
(bootloader) cid: SPCS_001
all:
finished. total time: 0.010s
I had to work the last few days and in general wanted to take a little break from this headache. Are there known issues with the latest TWRP? I'll downgrade to the flat 3.1 version later on tonight.
Click to expand...
Click to collapse
it is not a confirmed issue, but I saw more than a handful not being able to flash anything on the latest, downgrading fixed it for them.

[URGENT!] RUU Error - 9 RU_MAIN_VER_FAIL os-version in android-info missing or

When i tried to use RUU zip in download mode, it gives 9 RU_MAIN_VER_FAIL os-version in android-info missing or error.
My story:
Used PF 8.0 beta before and flash LeeDroid 4.0 last month.
Currently HK version of HTC10 received Oreo update so i wanted to go back to official Sense ROM.
Try to find the latest RUU for HK ROM but failed. And i decided to go back to Marshmallow and upgrade to N and then O.
I am currently using 2PS6IMG_PERFU[email protected]60331_39.13_F_release_478389_signed_2_4.zip in download mode to flash it. I have used this file before so it should be working.
(bootloader) kernel: lk
(bootloader) product: htc_pmeuhl
(bootloader) version: 1.0
(bootloader) max-download-size: 1579200000
(bootloader) serialno: Mod Edit: Removed
(bootloader) current-slot:
(bootloader) imei: Mod Edit: Removed
(bootloader) version-main: 2.41.708.31
(bootloader) boot-mode: download
(bootloader) version-baseband: [email protected]
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 2PS620000
(bootloader) cid: HTC__622

noname729 said:
When i tried to use RUU zip in download mode, it gives 9 RU_MAIN_VER_FAIL os-version in android-info missing or error.
My story:
Used PF 8.0 beta before and flash LeeDroid 4.0 last month.
Currently HK version of HTC10 received Oreo update so i wanted to go back to official Sense ROM.
Try to find the latest RUU for HK ROM but failed. And i decided to go back to Marshmallow and upgrade to N and then O.
I am currently using 2PS6IMG_PERFU[email protected]60331_39.13_F_release_478389_signed_2_4.zip in download mode to flash it. I have used this file before so it should be working.
(bootloader) kernel: lk
(bootloader) product: htc_pmeuhl
(bootloader) version: 1.0
(bootloader) max-download-size: 1579200000
(bootloader) serialno: Mod Edit: Removed
(bootloader) current-slot:
(bootloader) imei: Mod Edit: Removed
(bootloader) version-main: 2.41.708.31
(bootloader) boot-mode: download
(bootloader) version-baseband: [email protected]
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 2PS620000
(bootloader) cid: HTC__622
Click to expand...
Click to collapse
You need to find your HK ROM that has the software version of 2.41.708.31 with the radio version of 61226. I was able to locate it on a paid site. I'll download it and upload it to my Mega account for you. I may be able to get it uploaded tomorrow for you.

Got the ROM uploaded. You can either do a fastboot flash zip 2PS6IMG.zip (just rename the file) in Download Mode or put it on your SD Card and rename the file as 2PS6IMG.zip and get it flashed.
https://mega.nz/#!5V10mRYK!Ucwya3jxG5E5LIYJOKJK6nEvw7NGbatPY7QlHpRDzlI

hasoon2000 said:
Got the ROM uploaded. You can either do a fastboot flash zip 2PS6IMG.zip (just rename the file) in Download Mode or put it on your SD Card and rename the file as 2PS6IMG.zip and get it flashed.
https://mega.nz/#!5V10mRYK!Ucwya3jxG5E5LIYJOKJK6nEvw7NGbatPY7QlHpRDzlI
Click to expand...
Click to collapse
wow..you are the man!
you have an account in that website?

noname729 said:
wow..you are the man!
you have an account in that website?
Click to expand...
Click to collapse
I have an account that has files that I can download. My subscription does end soon.
Sent from my HTC 10 using Tapatalk

Hi, I have the same situation but my phone is S-on. Can I use the same method?
Thanks

hasoon2000 said:
Got the ROM uploaded. You can either do a fastboot flash zip 2PS6IMG.zip (just rename the file) in Download Mode or put it on your SD Card and rename the file as 2PS6IMG.zip and get it flashed.
https://mega.nz/#!5V10mRYK!Ucwya3jxG5E5LIYJOKJK6nEvw7NGbatPY7QlHpRDzlI
Click to expand...
Click to collapse
Sorry to ask but do you have RUU of this SKU (Hong Kong) but Marshmallow? I gave tried looking for it a ling time but no luck.
Thanks and regards

lilrice said:
Sorry to ask but do you have RUU of this SKU (Hong Kong) but Marshmallow? I gave tried looking for it a ling time but no luck.
Thanks and regards
Click to expand...
Click to collapse
I need the software version / build number and the radio version.
If you run a fastboot getvar all command and post that info as well, I'll see if I can help.
Make sure to quote this post or else I won't get the notification and I won't see it.

hasoon2000 said:
I need the software version / build number and the radio version.
If you run a fastboot getvar all command and post that info as well, I'll see if I can help.
Make sure to quote this post or else I won't get the notification and I won't see it.
Click to expand...
Click to collapse
Mine is Hong Kong CID 622, OS x.x.708.x
But I found it, thank you for your time