Zuk Z2 Plus stuck at EDL - 9008 port & Not booting [SOLVED] - Lenovo ZUK Z2 (Plus) Questions & Answers

PROBLEM : Lenovo Zuk Z2 is stuck at EDL mode and cannot boot back into system.
DON'T PANIC...
A bit more about it
Zuk Z2 Plus is kind of bricked at Edl mode i.e it is at 9008 , aye.
A bit wierd issue but yes, it suddenly went to EDL and after a dozen tries like Vol & Power button holding and stuff i am not able to get out of edl mode.
There is no LED blinking, no vibration, display won't turn on, no nothing - just dead and is at EDL mode.
I've flashed 1.9 ROM & 2.0 ZUI ROM via QFIL ( as my Zuk is bricked or stuck at EDL mode i can easily flash ) but these don't boot too, or flashed ZUI via MI Flash Tool, but same.
It stays at EDL MODE.
Just for the record, I have bricked z2 a couple of times and after some hard work to get that to 9008 from 900e was able to unbrick it after I was able to get it to EDL mode and do deep flash ... but now in this case I am stuck at EDL. OMG
Device automatically switched to edl..
After searching on the internet!
After searching a lot, i found that same issue has happened in other devices also, possible fix is let the battery drain (will take a long time ) and after that plug in charger as it will turn off edl or disassemble it and disconnect battery ( harmful way)
How I fixed it? / SOLUTION
I let the battery drain to 0% and after that I plugged in the charger and pressed power button for 5 seconds and Viola it booted.
Now, the question is I was able to drain the battery just in a day, what I did is 2 things:
1. Used OTG cable and connected it to another device for 4-5 hours[ - to charge that another device in hope to drain my Z2 Plus's battery.
2. I used a thread or a rubber elastic band and tied that to the phone with a small paper roll pressing the power button and kept it like that for about 5 hours ( at this stage phone keeps on rebooting into edl so drains battery but you will not get to know it as no response will be shown by it - expect the sound it comes if you have it connected with the PC.)
------ Other Methods which seen to work ------
Or another method is Service Center, you can easily lock bootloader by flashing QPST STOCK ROM as you are at EDL - 9008 port.
Or removing the battery and connect it, it will switch off EDL - for this go to Local Shop I don't recommend doing this at home
THANKS - HOPE IT WILL HELP YOU

EDIT : FIXED!!
PS: Don't quote the Whole Post

Try a deep flash

May be it can help you
Mod Edit: attachment showing external link removed

JIT05 said:
May be it can help you
Click to expand...
Click to collapse
May i know which is this platform?

Telegram

SOLVED THE ISSUE - FINALLY and updated the thread with SOLUTION.
JIT05 said:
May be it can help you
Click to expand...
Click to collapse
I fixed it, if you see I only posted that xD
Not_James_Bond said:
May i know which is this platform?
Click to expand...
Click to collapse
That is Telegram, one of the chat app for interacting with communities....
For example like this :
Mod Edit: External link removed
Mod Edit: Attachment with link to external group removed

Anybody who has similar issue, regardless of device would be benefited. [emoji111]️ Good Job
Sent from my Z2 Plus using Tapatalk

heerakjyotidas94 said:
Anybody who has similar issue, regardless of device would be benefited. [emoji111]️ Good Job
Sent from my Z2 Plus using Tapatalk
Click to expand...
Click to collapse
Yeah.

JIT05 said:
Telegram
Click to expand...
Click to collapse
kubersharma said:
SOLVED THE ISSUE - FINALLY and updated the thread with SOLUTION.
I fixed it, if you see I only posted that xD
That is Telegram, one of the chat app for interacting with communities....
For example like this :
Mod Edit: removed external link
Click to expand...
Click to collapse
Thank You.

Just Sharing Only Group For Discussion , Not Sharing Anything Related To Piracy [emoji4]
Mod Edit: external link removed

Thread closed, Xda being used to drive traffic to off-site group not permitted.

Related

Hard Bricked LG Optimus G

Regards.
Ist of all I would like to say why I am opening this new thread so my answer is that I tried my best (by god) searched XDA & Google for more than two days to fiend solution for my problem but can't get a solution so I opened this thread as my problem different from others at this forum.
Story is that I was enjoying my LG Optimus G for last 11 months. Shortly, It was rooted, boot-loader unlocked and running custom ROM namely Thinking Bridge. One day I needed usb otg support so I search for it and fined a mod by XDA member samm_cz at {http://forum.xda-developers.com/showthread.php?p=37896376#post37896376} when I flashed this the phone turned off and never turned on, Now neither I can't access CWM nor download mode even it does not respond to charger the only thing left is that when I connect charger and hold power button a red light blinks near front camera. I humbly request to All my seniors help me to get out of here. Hooping for good response.:crying::crying::crying::crying:
Imran Pirzada said:
Regards.
Ist of all I would like to say why I am opening this new thread so my answer is that I tried my best (by god) searched XDA & Google for more than two days to fiend solution for my problem but can't get a solution so I opened this thread as my problem different from others at this forum.
Story is that I was enjoying my LG Optimus G for last 11 months. Shortly, It was rooted, boot-loader unlocked and running custom ROM namely Thinking Bridge. One day I needed usb otg support so I search for it and fined a mod by XDA member samm_cz at {http://forum.xda-developers.com/showthread.php?p=37896376#post37896376} when I flashed this the phone turned off and never turned on, Now neither I can't access CWM nor download mode even it does not respond to charger the only thing left is that when I connect charger and hold power button a red light blinks near front camera. I humbly request to All my seniors help me to get out of here. Hooping for good response.:crying::crying::crying::crying:
Click to expand...
Click to collapse
When he died, had battery?
Imran Pirzada said:
Regards.
Ist of all I would like to say why I am opening this new thread so my answer is that I tried my best (by god) searched XDA & Google for more than two days to fiend solution for my problem but can't get a solution so I opened this thread as my problem different from others at this forum.
Story is that I was enjoying my LG Optimus G for last 11 months. Shortly, It was rooted, boot-loader unlocked and running custom ROM namely Thinking Bridge. One day I needed usb otg support so I search for it and fined a mod by XDA member samm_cz at {http://forum.xda-developers.com/showthread.php?p=37896376#post37896376} when I flashed this the phone turned off and never turned on, Now neither I can't access CWM nor download mode even it does not respond to charger the only thing left is that when I connect charger and hold power button a red light blinks near front camera. I humbly request to All my seniors help me to get out of here. Hooping for good response.:crying::crying::crying::crying:
Click to expand...
Click to collapse
Yes it is hard bricked, unfortunately. You need to send it to the LG service centre. Do not attempt to unscrew the cover and open it up to reset the battery. It did not work for me and my warranty almost got voided because they found my thumbprints. However I pretended I did not know anything and they replaced my whole motherboard.
Nite.Achilles said:
Yes it is hard bricked, unfortunately. You need to send it to the LG service centre. Do not attempt to unscrew the cover and open it up to reset the battery. It did not work for me and my warranty almost got voided because they found my thumbprints. However I pretended I did not know anything and they replaced my whole motherboard.
Click to expand...
Click to collapse
Thanks for reply brother but I don't know where is LG Service Centrer and I saw its warranty card and unfortunately its warranty has expired. Now my question is that if I go to LG Service Centrer will they deal me as phone's warranty has expired and I am ready to pay for this. My phone was at 75% battery when bricked.
:crying:
Imran Pirzada said:
Thanks for reply brother but I don't know where is LG Service Centrer and I saw its warranty card and unfortunately its warranty has expired. Now my question is that if I go to LG Service Centrer will they deal me as phone's warranty has expired and I am ready to pay for this. My phone was at 75% battery when bricked.
:crying:
Click to expand...
Click to collapse
Hardtron said:
When he died, had battery?
Click to expand...
Click to collapse
Thanks for reply brother My phone at 75% battery when I got bricked.
Imran Pirzada said:
Thanks for reply brother My phone at 75% battery when I got bricked.
Click to expand...
Click to collapse
They will replace your phone, but you will have to pay. I'm from Singapore and that time I was told to pay SGD $350 to replace. But I did not pay.
I guess the price may have dropped because of the G2 and G Flex which are the current flagships. Maybe you would pay $250? I'm just assuming.
But for my place, once my warranty ends, I would have to pay $25 for labour charge and additional costs for parts replacment if there is anything wrong.
I had the same problem and I solved it by disconnecting and reconnecting the battery
Inviato dal mio Optimus G utilizzando Tapatalk
ermoto said:
I had the same problem and I solved it by disconnecting and reconnecting the battery
Inviato dal mio Optimus G utilizzando Tapatalk
Click to expand...
Click to collapse
Thanks brother I will try it.
Imran Pirzada said:
Thanks brother I will try it.
Click to expand...
Click to collapse
when red light is blinking check whether your device is recognized in computer/pc, try pressing up button and power button sametime to boot into downlload mode.
if you can do that then flash the teeny bin method to put recovery first...
mathprav said:
when red light is blinking check whether your device is recognized in computer/pc, try pressing up button and power button sametime to boot into downlload mode.
if you can do that then flash the teeny bin method to put recovery first...
Click to expand...
Click to collapse
Brother latest update is that my phone is recognised by my PC as QHSUSB_DLOAD in device manager under other devices what should I do now?:laugh:
ermoto said:
I had the same problem and I solved it by disconnecting and reconnecting the battery
Inviato dal mio Optimus G utilizzando Tapatalk
Click to expand...
Click to collapse
Brother latest update is that my phone is recognised by my PC as QHSUSB_DLOAD in device manager under other devices what should I do now?
Imran Pirzada said:
Brother latest update is that my phone is recognised by my PC as QHSUSB_DLOAD in device manager under other devices what should I do now?
Click to expand...
Click to collapse
It means it is hard bricked. You need to JTAG it or send it to LG service centre. No other way it can be solved.
A possible solution
Imran Pirzada said:
Regards.
Ist of all I would like to say why I am opening this new thread so my answer is that I tried my best (by god) searched XDA & Google for more than two days to fiend solution for my problem but can't get a solution so I opened this thread as my problem different from others at this forum.
Story is that I was enjoying my LG Optimus G for last 11 months. Shortly, It was rooted, boot-loader unlocked and running custom ROM namely Thinking Bridge. One day I needed usb otg support so I search for it and fined a mod by XDA member samm_cz at {http://forum.xda-developers.com/showthread.php?p=37896376#post37896376} when I flashed this the phone turned off and never turned on, Now neither I can't access CWM nor download mode even it does not respond to charger the only thing left is that when I connect charger and hold power button a red light blinks near front camera. I humbly request to All my seniors help me to get out of here. Hooping for good response.:crying::crying::crying::crying:
Click to expand...
Click to collapse
While looking in to rooting my device, I found this possible solution for your device:
- http://forum.xda-developers.com/showthread.php?t=2010624
Hope this helps :good:
Thanks
TheStigOnline said:
While looking in to rooting my device, I found this possible solution for your device:
- http://forum.xda-developers.com/showthread.php?t=2010624
Hope this helps :good:
Click to expand...
Click to collapse
Thanks brother but It will be effective for me if I could get in download mode.:crying::crying:
Request to seniors
Any suggestion please
Imran Pirzada said:
Any suggestion please
Click to expand...
Click to collapse
Its not hardbricked, I had the exact problem, just use the correct driver software specified in teenybin and flash the given image
Its HardBricked. You flash some software mod for an Alcatel phone. Is like i flash a ROM for galaxy s2. Obviously it will brick.
nch26 said:
Its HardBricked. You flash some software mod for an Alcatel phone. Is like i flash a ROM for galaxy s2. Obviously it will brick.
Click to expand...
Click to collapse
it can be still recovered, i have recovered the phone from the same state...( what i believe is this lg phone can't be hardbricked, you can get it back)
mathprav said:
it can be still recovered, i have recovered the phone from the same state...( what i believe is this lg phone can't be hardbricked, you can get it back)
Click to expand...
Click to collapse
I dont think so. you can brick this phone. The red led means two things.
1. You dont have battery
2.Brick
nch26 said:
I dont think so. you can brick this phone. The red led means two things.
1. You dont have battery
2.Brick
Click to expand...
Click to collapse
well, battery was available, and i had the exact state, only can see the red led, then when connected to PC it showed QHSUSB_DLOAD something
then i changed the windows driver to the one provided by lg drivers( how to do that shown in teenybin thread) then after flashing it i was able to see the fastboot mode and then went into the recovery used adb sideload to restore the nandroid backup and my LG Phone was back to life again....

OP3 bricked. Tried Mega Unbrick guide but my phone wont switch on or even vibrate.

I tried the 1st method on the mega unbrick guide.. i.e. turned off Driver Signature Enforcement, device shown on device manager and updated to show Qualcomm 9008, started the MSM download tool successfully and text in green showed up as mentioned. Then I disconnected the device and tried to switch on my phone but literally nothing happens. No vibration, nothing on screen(not even the Oneplus logo). Please help me on what to do now. Thanks
PS: Downloading the Method 2 file(unbrick tool full (1GB)) gonna take a while since I have really slow internet. I have low confidence on it to work as of now.
Any help would be appreciated. Thanks
Vennali said:
I tried the 1st method on the mega unbrick guide.. i.e. turned off Driver Signature Enforcement, device shown on device manager and updated to show Qualcomm 9008, started the MSM download tool successfully and text in green showed up as mentioned. Then I disconnected the device and tried to switch on my phone but literally nothing happens. No vibration, nothing on screen(not even the Oneplus logo). Please help me on what to do now. Thanks
PS: Downloading the Method 2 file(unbrick tool full (1GB)) gonna take a while since I have really slow internet. I have low confidence on it to work as of now.
Any help would be appreciated. Thanks
Click to expand...
Click to collapse
was the process successfully if it was done with green alphabets in msm tool than u good to go..... many cases its a issue with battery so just keep ur device for charge for some time with original charger n try to on ... if not just visit my youtube (TECHIBEE) Channel and ull find helpfull videos thr about oneplus devices
ashokmor007 said:
was the process successfully if it was done with green alphabets in msm tool than u good to go..... many cases its a issue with battery so just keep ur device for charge for some time with original charger n try to on ... if not just visit my youtube (TECHIBEE) Channel and ull find helpfull videos thr about oneplus devices
Click to expand...
Click to collapse
I dont think its an issue with charge in the phone.. kept it over an hour for it. I'll check out the YT channel thanks!
PS: MSM tool was successful but still no luck with my OP3 sadly!
Try this method
https://forum.xda-developers.com/showpost.php?p=68245482&postcount=111
abhi0502 said:
Try this method
https://forum.xda-developers.com/showpost.php?p=68245482&postcount=111
Click to expand...
Click to collapse
This mega unbrick method 2 work well. I'd unbrick 2 times with this.

Hard bricked and Solved.

First things first, NEVER RESTORE A TWRP BACKUP YOU CREATED IN ONE VERSION IN ANOTHER VERSION.
Now coming to my situation, I installed the Deodexed Stable Zui Oreo ROM but as usual got bored with the zui and wanted to go back to my fav Pixel experience Rom so I clean flashed it from the unofficial hendibudi recovery but I couldn't use my internal storage and I once earlier read in another thread that installing 3.0.3 decrypts it so I installed that recovery and clean flashed AEX5.2 Rom this time and same internal storage problem continued so my lazy ass thought I'll restore the TWRP backup I created when I unlocked the bootloader instead of flashing through qfil and that was my mistake.
I created the backup on 3.1.0 but now I was on 3.0.3 so as soon as I restored the backup and rebooted, my phone didn't turn on, no zuk logo or led or anything, if I long press the power button it just vibrates and the led flashes for a sec, that's all.
Edit: feels like this thread belongs to the News/Discussions section than here but meh
Edit2: Solution in Post #4
It seems like qfil, mi flash method is last as your bootloader is also corrupted, and this happens because there are many critical hidden partition on our device so it mess up, when you install first twrp releases, you will notice there are 7 8 partition and in latest one they all are hidden.
narshi shukla said:
It seems like qfil, mi flash method is last as your bootloader is also corrupted, and this happens because there are many critical hidden partition on our device so it mess up, when you install first twrp releases, you will notice there are 7 8 partition and in latest one they all are hidden.
Click to expand...
Click to collapse
well if it's that easy I wouldn't be worried at all but unfortunately my situation is a bit different, I can't flash anything as my phone is recognized as 900E, to flash anything the phone should be recognized in 9008(edl) mode and for that I have to strip the cable and short circuit with it and all that, which is really a hit or miss kinda situation so kinda worried!
But seems like I have no other choice so let's see what happens, I tried stripping the stock usb cable and it got split into half lmao
now I'll buy another cable and will try the copper wire method instead of splitting it
Edit: yeah ik that different versions of TWRP are different but I wanted to restore only the data partition and my data was already encrypted so I thought I have nothing to lose, I was like if it doesn't work I'll flash the full firmware again but didn't expect it to fully brick the phone
Okay the primary reason for me creating this thread was to let y'all know how I bricked my device so that y'all won't repeat my mistake but I saw some people here and there recently asking how to resurrect their device so thought I'll share how I got mine working wishing it'll help such people.
My phone was completely dead, the hardware buttons weren't doing anything, the phone doesn't power off but all I could see was a black screen, so I had to follow THIS GUIDE.
But the above situation is a rarity, I guess most of you ppl could get to the zuk logo or your led keeps flashing and you can use your hardware buttons, in such situations, follow THIS GUIDE.
The above links are for you to get your phone to 9008 mode to be able to flash the stock firmware, but if you don't know how to flash,
refer THIS GUIDE.
Flashing problem
i got phone into 9008 port following ur guide and installed qfil everything went good problem is after hitting download buton in qfil after some time it says error "sahara failed".
seetharam55555 said:
i got phone into 9008 port following ur guide and installed qfil everything went good problem is after hitting download buton in qfil after some time it says error "sahara failed".
Click to expand...
Click to collapse
Only one solution is there.. after u get sahara error.. disconnect your phone and cable, then again turn your phone on. And then turn it off... After that press volume up+ power button simultaneously while connecting to the usb port, if you are successful, within 2-3 seconds you have to press the download button on QFIL.. then it should work... You can try 2-3 times... For demo, but thia is the only way out of this hard brick
.. i suffered in the sahara error for 3 days since i flashed OOS on my z2 , till today i finally got the solution
sidS6 said:
Only one solution is there.. after u get sahara error.. disconnect your phone and cable, then again turn your phone on. And then turn it off... After that press volume up+ power button simultaneously while connecting to the usb port, if you are successful, within 2-3 seconds you have to press the download button on QFIL.. then it should work... You can try 2-3 times... For demo, but thia is the only way out of this hard brick
.. i suffered in the sahara error for 3 days since i flashed OOS on my z2 , till today i finally got the solution
Click to expand...
Click to collapse
thanks for response.What do u mean by "succesfull".and other thing to turn off the phone it takes me nearly 2 min constant pressing of power button, is this normal.
seetharam55555 said:
thanks for response.What do u mean by "succesfull".and other thing to turn off the phone it takes me nearly 2 min constant pressing of power button, is this normal.
Click to expand...
Click to collapse
Not 2 minutes but i think 30 seconds at max.. and by successful i mean that you get into Qualcomm 9008 qdloader mode in qfil
---------- Post added at 05:13 PM ---------- Previous post was at 05:11 PM ----------
The main thing is you have to immediately press the download button(within 2-3 seconds) after reconnecting into 9008 mode
Briked my phone flasing oos, solved it in the first go usimg qpst method.
Rahil4321 said:
Briked my phone flasing oos, solved it in the first go usimg qpst method.
Click to expand...
Click to collapse
You didn't got Sahara error?
seetharam55555 said:
thanks for response.What do u mean by "succesfull".and other thing to turn off the phone it takes me nearly 2 min constant pressing of power button, is this normal.
Click to expand...
Click to collapse
Were u able to unbrick?
Thanks
sidS6 said:
Were u able to unbrick?
Click to expand...
Click to collapse
yes it worked but as u said we have to hit download button within 2 sec....thank you very much u nearly saved 1000 rupees for me.
seetharam55555 said:
yes it worked but as u said we have to hit download button within 2 sec....thank you very much u nearly saved 1000 rupees for me.
Click to expand...
Click to collapse
Congrats bro! But i lost my 3 cables in ths process.. that equals 700 rs.. but i learned a great lesson? no probs
seetharam55555 said:
i got phone into 9008 port following ur guide and installed qfil everything went good problem is after hitting download buton in qfil after some time it says error "sahara failed".
Click to expand...
Click to collapse
dude just cut the cable and make intersection betwwen vlack and gree wire and put the cable into phone , got edl mode simple ways
sidS6 said:
Congrats bro! But i lost my 3 cables in ths process.. that equals 700 rs.. but i learned a great lesson? no probs
Click to expand...
Click to collapse
Why did you wasted 3 cables for?
seetharam55555 said:
Why did you wasted 3 cables for?
Click to expand...
Click to collapse
Coz while spliiting, one got split into half ? and the other one got bent so it was unusable.. i had buy the third one
sidS6 said:
Coz while spliiting, one got split into half ? and the other one got bent so it was unusable.. i had buy the third one
Click to expand...
Click to collapse
Ohh you tried that method i did like this
sidS6 said:
You didn't got Sahara error?
Click to expand...
Click to collapse
You don't need to flash via qpst when you see logo but device wont boot it mean you locked your bootloader so all you need to do is unlock it again that's all
Nirmal0001 said:
You don't need to flash via qpst when you see logo but device wont boot it mean you locked your bootloader so all you need to do is unlock it again that's all
Click to expand...
Click to collapse
Unfortunately learnt this after unbricking my device
I had installed RR mix rom in my Zuk Z2 plus. while trying to enter fastboot mode, it went off. Now it is completely dead. not being recoganized in my PC.In device manager it is not shown. Tried to deep flash through Qfil, but didn't recoganize port.If i plug in charger also no LED indication, If I disconnect battery & plug in for charging, white LED slowly blinks, in the same mode if I connect charger blinking white LED continues. But once I remove charge & reconnect it shows nothing. again if I remove battery & reconnect, again white LED starts blinking. Apart from this nothing is shown, phone completely dead. Can anybody help please. I tried through Qfil, tried by shorting black & green cable, all types of key combinations.

lenovo z2 plus(z2131) hard bricked

i have been wandering around and have came across solutions and will be trying deep flash soon, but need to clear some of my doubts.
device current state- vibrates and led flashes every 10-12 secs
doubts-
*now i'm not able to turn the device off. i have tried holding power button for 2 mins and also tried holding and releasing power button at second led flash/vibration.
* in device manager the device doesn't shows up in any category.(z2 plus drivers installed and qualcomm drivers installed)
*should i deep flash it in this state? and will it work on usb 3.0 device? because all 3 ports of my laptop are 3.0.
update- thanks for all your views and replies. I successfully booted up my device using deep flash method.
https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/
The above link should help you.
seking said:
The above link should help you.
Click to expand...
Click to collapse
My device wasn't even showing up as port 900e and neither the zuk logo was appearing. Anyways, I deep flashed it and now it's up and running. Thank you for your help!!:good:
[email protected] said:
My device wasn't even showing up as port 900e and neither the zuk logo was appearing. Anyways, I deep flashed it and now it's up and running. Thank you for your help!!:good:
Click to expand...
Click to collapse
how u deep flash it ??
rishavsoni said:
how u deep flash it ??
Click to expand...
Click to collapse
Head over to https://zukfans.eu/community/thread...-from-hard-brick-state-9008-mode-easily.3504/
I did the process shown to power off device but I don't think it worked and other than that I followed that tut only basically. But I carried on with deep flashing it. You can also find deep flash tutorial here, in XDA forums,
seking said:
https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/
The above link should help you.
Click to expand...
Click to collapse
what location in VPN I need to show to this link?

Device redmi 1s dead please help !!!!!

Accidentally my phone droped on the floor after that it kepps the mi logo loop after some time the battery got dead and phone also not charging. While connecting to the charger cable the led blinking and looping. Buy my phone doesn't charging and while on the flash process without battery the fastboot mode opens and closes rythmically.and my computer doesn't take the time to load the drivers. Now what to do feeling dizzy....
Please help me out of this problem. I think it bricked but not hard. Because the fastboot logo comes but not more than 5 seconds it goes off. Please help
Try giving it to a local repair store.
I also had the same problem. If I used to remove and put the battery back, it used to reboot. I tried flashing using fastboot, but it used to reboot every 6 seconds. According to some friends of mine (Thanks to them) I gave it to a store, which in turn (I dunno how) hardbricked the device. I connected it to the PC, tried to go to fastboot, and it shows up as QCOM Loader 9008, which basically tells you your device is hardbricked.
Fastboot didn't work.
Using MiFlash Tool, while flashing through the QcomLoader, it showed "Did not receive hello packet"
Tried many times more, didn't work out.
So, I went and tried the trusted method: TEST POINT method.
It worked out. Now my armani is up and running!
TL : DR;
Try giving it to a local repair store (not Mi service center, they didn't help me AT ALL.)
Something might have dislodged.
Or
Try testpoint method, google for it
it *might* work. Well, that worked for me.
Not end at all
Hi, sorry for very late reply
Recently I discovered that the battery is dead not working at all. And while doing the test point method I think battery power is needed! So I ordered a spare battery after the delivery I will do the test point method agian. Currently if I plug in my phone thorough usb to my computer the qcom 9008 port shows but while flashing it gets detached then re shows up . And the flashtool error happens. I think a battery power is required so that this failure is happening.
So, what do you think is edl mode requires battery power?.
Need help because I have to fix it. It's my one and only loved phone of all time.
Currently I am using my friends phone to discuss about this matter.....please help me.....
parag2001 said:
Hi, sorry for very late reply
Recently I discovered that the battery is dead not working at all. And while doing the test point method I think battery power is needed! So I ordered a spare battery after the delivery I will do the test point method agian. Currently if I plug in my phone thorough usb to my computer the qcom 9008 port shows but while flashing it gets detached then re shows up . And the flashtool error happens. I think a battery power is required so that this failure is happening.
So, what do you think is edl mode requires battery power?.
Need help because I have to fix it. It's my one and only loved phone of all time.
Currently I am using my friends phone to discuss about this matter.....please help me.....
Click to expand...
Click to collapse
You do not need battery power for test point method.

Categories

Resources