n7100 boot problem can not be fixed - Galaxy Note II Q&A, Help & Troubleshooting

Hello dear friends.Here is the problem
I own a N7100 and the mother board was broken.So i got a new one from china.They say it is original and when i check it visually i think that it is original.(i am not sure).It had been working normal by original 4.1 rom.It had cwm recovery.And i wanted to flash a custom rom and it rocommends to use TWRP.So i tried to flash it.But it seemed that i could not install it.It showed CWM when i try to enter recovery mode.After 2-3 attempt it started to stuck on SAMSUNG N7100 screen.Now i neither can enter recovery mode nor to the rom.It loops on samsung screen.The only thing works is download mode.On download mode screen
Product name : GT-N7100
And it says " RPMB: INVALID RPMB DATA"
I can not flash a rom via odin.it always give an error.What can i do to fix it?Is it a hardware problem?can you please explain the ways of fixing it?
Thank you.when i try to flash by heimdall on linux it says
Heimdall v1.4.1
ERROR: Failed to send end session packet!
Releasing device interface...

Related

Prestigio 4500T Duo need to revive

I need help please, because I can't get my new prestigio 4500T turn on.
I first did the CWM recovery in this site, androidforum.cz/pro-pap4500t-dc-1-2ghz-s-jb-4-1-1-t38976.html
and it was all ok.
But then I wanted to remove the CWM recovery of my phone, because I had some problem updating my phone to the new rom because of it,
and I went to the same program I installed CWM recovery, Smart Phone Flash Tool, and I put the same scatter file I used to install, and instead of clicking on download I clicked Format, and then format whole flash, because it was there that I would take CWM recovery of my phone.
Now I can't turn my phone on, when I connect usb at pc, it connects and disconnects a lot of times. I even tried to do the same steps to download the CWM recovery on my phone but in SP Flash Tool I get this error: BROM ERROR: S_DL_GET_DRAM_SETTING_FAIL (5054)
[HINT]: Please check your load matches to your target which is to be downloaded.
I don't know what to do and please Help me. Thanks
Nobody answers? Please can anybody help me?
ddqgarces said:
I need help please, because I can't get my new prestigio 4500T turn on.
I first did the CWM recovery in this site, androidforum.cz/pro-pap4500t-dc-1-2ghz-s-jb-4-1-1-t38976.html
and it was all ok.
But then I wanted to remove the CWM recovery of my phone, because I had some problem updating my phone to the new rom because of it,
and I went to the same program I installed CWM recovery, Smart Phone Flash Tool, and I put the same scatter file I used to install, and instead of clicking on download I clicked Format, and then format whole flash, because it was there that I would take CWM recovery of my phone.
Now I can't turn my phone on, when I connect usb at pc, it connects and disconnects a lot of times. I even tried to do the same steps to download the CWM recovery on my phone but in SP Flash Tool I get this error: BROM ERROR: S_DL_GET_DRAM_SETTING_FAIL (5054)
[HINT]: Please check your load matches to your target which is to be downloaded.
I don't know what to do and please Help me. Thanks
Click to expand...
Click to collapse
You messed up boot file.Try to find original boot.img here on XDA and try to flash it via PC,or find original stock rom for flashing via SPFlashTool try that
jaskooo said:
You messed up boot file.Try to find original boot.img here on XDA and try to flash it via PC,or find original stock rom for flashing via SPFlashTool try that
Click to expand...
Click to collapse
Thanks for your help, I have a boot.img of the stock rom, I put in the same folder of MT6577_Android_scatter_emmc and CheckSum.ini , but when I try to download via SP flash tool I get this error:
Image Bootimg checksum failed! Checksum reference value (0x5583) in the config.ini file.
Please re-fill correct checksum values in checksum.ini.
I don't know what are the checksum values, can you tell me where i can find these values?
I am getting this DRAM error, because I don't have the correct files to flash in SP flash tool.
Please can you give me all those files needed to put a whole new firmware in y phone, I need the preloader file, and etc.
My phone can't detect preloader, as it did, and I can't boot it, it's like dead, only appears a red light when I connect to pc and a MTk USB Port (COM).
Please help me with the files needed to flash my whole phone in sp flash tool
Need full ROM with scatter file
Hi Guys, I am looking for full ROM including scatter file for PAP4500T. I need it to load all needed (Preloader, MBR, EBR1, UBOOT, BOOTIMG, RECOVERY, SEC_RO, LOGO, EBR2, ANDROID, CACHE, USRDATA) in to the SP Flash Tool. It can be from Stock or any working ROM. If You could provide me Working ROM with all these and with scatter file which will load everithink to the SPflashTool I would really appreciate that.
Thank You in advance.

"complete write operation failed " I Cant flash any Rom On Mobile.

Hello Guys .. My mobile was stuck at "Galaxy Note II bootloop" and cant get access to recovery screen ,, just download mode for flash any rom ,, but when I flash a rom it shows me this msg"complete write operation failed" in Odin and I cannot setup the ROM .. So please whats the solution as I changed the cable , closed kies and changed pc but still the problem
Publish the Odin log so we can see where the flash process stops and any error messages.

SM-T520 - Unable to flash TWRP - Tried with Odin and Heimdall

Hi,
So I try to flash TWRP. I tried like 10 differents versions. All version below 3 makes a bootloop when accessing recovery mode, and above 3 are bringing me back to download mode (without the question to accept or not, and without the text at the top left corner of the screen).
I tried with odin under windows (tried with 3.0.7, 3.10.x and I think 3.12 as well), I tried with heimdall under linux also. Here's the output of heimdall:
Code:
[[email protected] ~]# heimdall flash --RECOVERY twrp-3.1.0-1-picassowifi.img --no-reboot
Heimdall v1.4.2
Copyright (c) 2010-2017 Benjamin Dobell, Glass Echidna
censored
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
censored
Initialising connection...
Detecting device...
Claiming interface...
Setting up interface...
Initialising protocol...
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
100%
RECOVERY upload successful
Ending session...
Releasing device interface...
I'm able to go to odin mode by holding down VOL-DOWN + Power (no need to hold the home button) and I go try to go to recovery mode with VOL-UP + Power + Home.
The OS on the tablet is Android 4.4.2 stock rom. I tried to root it but when the OS loads, it does a quick update and root is not working as well.
Anyone else had the same problem than me?
hello
first change the usb cable i don't know but 8/10 it's the solution
back to the origine
install cfautorout ( all needed is in the zip)
then install twrp
regards
Hi I made a post in ressurection remix post in development. I posted a link to everything I used to root my tablet sm-t520. I used cf-autoroot. The best way to flash custom recovery using Odin. Go to official website and download the .Md5 file. Should be called like picassowifi.img.md5 or something similar. Put that in AP slot in Odin and run, that should work. Let me know if you need any other help.
SM-T520
So I just did 5 of these Samsung SM-T520 tablets for work as the 4.4.2 OS’ would not allow us to use some special software for doing digital inspections on Vehicles.
Our software maker said we needed 5.0 and higher so after many hours of trial and error, I found the right process and rom that worked.
For installing TWRP I used Odin, but had similar problem as you. Fix was to go to TWRP website and make sure you download there version for your device but I could only get 3.0.0.0 to work anything above or below caused issues. I also installed micro SD card into units to use as back up and drop all files required to install new rom. I simply just used windows drag and drop or copy and drop feature. I also noticed that while in TWRP and doing backup that if screen saver on tablet activated it would cause a crash and reboot, My fix for this was to go into TWRP screen time out settings and max it out , also even though tedious I would touch screen every 60 second just to make sure counter was reset. I did have one tablet crash after bad rom installation but putting tablet into download mode, running Odin to install TWRP version 3.0.0.0 got me back up and running and allowed me to install better rom. Please note I take no credit for any of this, as many hours of research and testing and trying different things were a combination of other people’s work. That being said I did try the TWRP version 3.0.0.0 on my own without any direction from others as I was just testing things out and got lucky. Hope this helps. If you need more info on exact Rom and files just let me know.
But I will tell you this I did try the Latest versions of Lineage OS "at least 5 versions and was never able to get a stable system, had multiple problems with camera crashing "even with out using it", OS crashing, constant Reboots, Reboot looping and others. All my tablets have been running smooth for 3 weeks no problems at all so far with a different ROM that is base on the 7.1 nougat. I have not given up on Lineage yet just going to wait a bit as it is possible The inspection software I need is not compatible with something in the Lineage OS. Good luck
caution
twrp 3.1.0.0 doesnt work
regards

GT-I9195 - unable to flash recovery

Hello!
I bought a GT-I9195I - 8 GB via Ebay. The former owner tried to flash an update but the battery drained leaving the phone unable to boot.
What I did so far:
normal booting - only showed the model number, not even Samsung boot logo
reovery mode - booted, but showed some Errors (sorry, don't remember them exactly), some partitions could not be mounted
factory reset from stock recovery - failed (some partitions could not be formatted)
wipe cache - failed
Then I got the TWRP for the phone as described in
https://forum.xda-developers.com/ga.../rom-cyanogenmod-14-0-s4-mini-3g-lte-t3471761
and tried to flash it with heimdall flash --RECOVERY recovery.img --no-reboot (running linux on the Desktop, so I can't use ODIN).
This seemed to be successful, but the stock recovery was still there, showing the same errors.
So I tried again, getting the following messages:
Code:
[email protected]:~/Downloads/SamsungS4mini$ sudo heimdall flash --RECOVERY recovery.img --no-reboot
Heimdall v1.4.1
Copyright (c) 2010-2014 Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Claiming interface...
Setting up interface...
Initialising protocol...
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
100%
ERROR: Failed to confirm end of file transfer sequence!
ERROR: RECOVERY upload failed!
Ending session...
Releasing device interface...
The phone showed: "Flash write failure".
Trying to boot ends up in the black screen "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again".
Same result in several tries with TWRP and CWM.
I flashed the TWRP file already this way on another I9195, so I am sure, I've got the correct recovery for this model. Only download-mode is still accessible.
I read some similar threads now, but didn't find something that seemed to match this case.
Is there anything I can do?
I hope that someone can help me.
Regards, Stefan
Hi have you tried to flash stock rom
bzpbavarian said:
Hi have you tried to flash stock rom
Click to expand...
Click to collapse
I thought, I tried. But yesterday found out, this phone is an GT-I9195 LTE (search at imeipro.info). So I had the wrong stock rom. Sammobile is down for normal Downloads until tomorrow. Then I'll fetch the (hopefully) right files and try again.
Someone here has a link to a suiting debrick.img? All the links I found by searching the forum seem to be down.
Okay, I'm giving up now. The phone refuses to flash the original rom and recovery.
Starting with a debrick.img (https://forum.xda-developers.com/showthread.php?t=2473783 was my guide) doesn't change anything.
Maybe the chip is broken? I installed custom recovery and lineage on two other phones this weekend, so I know how to do it.
Thanks for reading and for all the helpful things I found in this forum!

How to install galalxy A6+ stockrom (SM-a605GN)

Hello everyone,
How do I resolve the message "MDM IS SET. Phone will be reboot 3 sec" and or "MDM MODE. CAN'T DOWNLOD [2] eMMC write fail: SBL1".
I have a device samsung galalxy A6+ (SM-a605GN) in a loop showing the message "MDM IS SET. Phone will be reboot 3 sec", I can't get into recovery mode or hard reset, I can only access download mode. However, I can't install a new rom via odin (stock or custom, I tried several versions of binary and odin), how do I solve or what would be "MDM MODE. CAN'T DOWNLOD [2] eMMC write fail: SBL1" or would it have some other way to fix without odin
You're in the wrong forum buddy.

Categories

Resources