I have a canvas a1 AQ4501. Some days ago it just stopped working normally. When it turns on, I see the company logo with half screen turned yellow. Then it tries to restart but the same problem.
I have tried:
Using SP flash tools version 5.1524 but it goes into 2020 error while flashing, without battery. With battery phone is not detected.
Using twrp recovery to install cyanogenmod but it says partition had unexpected data after OTA update, something of this kind (did this using adb sideload)
The only thing that I can do with the phone is go into fastboot mode, recovery mode gets stuck on company logo. I can go to twrp recovery mode successfully.
I am using a windows 10 computer. Phone was on marshmallow when it last worked. I do not have an SD card. I have tried pressing both volume up and down with and without power button to flash using sp tool but phone is not detected bu sp flash tool in this case. I have tired meta mode (pressing volume up and power) here, phone is detected by sp flash tool but it goes into 2020 error BROM ERROR : S_BROM_CHKSUM16_MEM_RESULT_DIFF (2020).
Please help me as this phone is dear to me and has sentimental value.
Thanks for your time.
Bro give ur phone to MMX service center they will solve ur problem
Hi guys,
I request your urgent help. Yesterday I tried to install a Marshmallow custom ROM (pac_A6020_MM.Alpha.1.Official_20160704-204606) in my Lenovo VIBE K5 Plus A6020a46. Now it seems bricked. I can boot into fastboot mode but not into the recovery mode. When I turn on, it it is just stuck on Lenovo Logo screen. I cannot flash with QFIL as the port is not detected on my Windows 10 Laptop. What should I do? Please help.
Download stock ROM and twrp recovery and flash twrp recovery in fastboot mode. Then flash stock ROM using twrp recovery. That's it.
cityengineers said:
Download stock ROM and twrp recovery and flash twrp recovery in fastboot mode. Then flash stock ROM using twrp recovery. That's it.
Click to expand...
Click to collapse
Thank you for your reply. But now device is not shown in adb command line "adb device". So I cant continue. Neither QFIL recognize the device port.
Please check the screenshot : http_//imgur_com/nMu7sfe
I've faced the same problem that you have said mobile didn't detect by the PC, that's USB driver problem, make sure you installed USB drivers for your device, if not then install USB drivers for your device, then only PC can detect your device. Then flash the twrp and flash the stock ROM via twrp.
try using QLIP and press the volume + button
http://www.mediafire.com/download/1...1.2_BMAIN_16G_ROW_otafull+By+GSMDevelopers.7z
http://www.mediafire.com/download/u4b8uzz4dy454a2/A6020a46+SDcard+upgrade+SOP.doc
here is a link for firmware and instructions
Password - gsmdevelopers.com
Thank you all dear friends for your timely help. But in my case none of the methods above worked completely. I couldn't flash my Vibe K5 Plus with QFIL because it never detected the port. When I tried restarting the phone holding Volume + key, port just showed up and when I clicked on download button in QFIL, the phone restarted, the port disappeared and nothing happened. So, that method also failed.
Now I just showed the problem at Lenovo Service center. They made it, but installed a very old version (A6020a46_S024) of OS from which I could not update to the latest one (A6020a46_S048_160701_ROW). It showed some ota error after downloading almost 156MB. Luckily I could find the latest ROM (A6020a46_S048_160701_ROW) from the Russian Lenovo Forum. It helped me to update my Lenovo Vibebe K5 Plus_A6020a46 to the latest version. Once again thank you all. :good:
Jintu Jose said:
Thank you all dear friends for your timely help. But in my case none of the methods above worked completely. I couldn't flash my Vibe K5 Plus with QFIL because it never detected the port. When I tried restarting the phone holding Volume + key, port just showed up and when I clicked on download button in QFIL, the phone restarted, the port disappeared and nothing happened. So, that method also failed.
Now I just showed the problem at Lenovo Service center. They made it, but installed a very old version (A6020a46_S024) of OS from which I could not update to the latest one (A6020a46_S048_160701_ROW). It showed some ota error after downloading almost 156MB. Luckily I could find the latest ROM (A6020a46_S048_160701_ROW) from the Russian Lenovo Forum. It helped me to update my Lenovo Vibebe K5 Plus_A6020a46 to the latest version. Once again thank you all. :good:
Click to expand...
Click to collapse
Please write the method how to updated it if you used QFIL. I think a lot of users can get help from your experience!
For drivers, install QDLoader HS-USB Driver drivers (google them)
and if you still can not detect any HS USB port in device manager but see an ADB Interface port. upgrade drivers of ADB port with QDLoader HS-USB Driver you downloaded earlier
This will detect your phone,
Good Luck!
QFIL was not useful for me. When I started the phone holding Volume+ button it detected the port and when clicked on the download button in QFIL the phone restarted after 3-5 seconds with blank screen, after a few seconds showed an error message "Download Fail, Port not Available". Then I had remove the battery to start my phone in the mormal mode. As I have said above, I had to approach Lenovo Service center to recover my Lenovo VIBE K5 Plus_A6020a46. They recovered it and installed the oldest OS version for it. It had many problems with that version, such as draining battery very soon and heating issues etc. I could not update it with Lenovo companion app. It downloaded the 156MB update, but during installation it showed a weird OTA error. I tried it for 5 times, but the result was always the same.
So I searched for the latest update ROM in the internet (A6020a46_S048_16070 1_ROW) I got it from an Russian Lenovo Community website. I extrated the zip file (A6020a46_S048_16070 1_ROW_QPST.zip). There were many ota update files and a "system" update file. I copied that "system.zip" file to the phones SD card and updated from there using recovery mode. It was successful.
If someone is in need of the Latest ROM (1.34 GB) for the Lenovo VIBE K5 Plus_A6020A46 go to:- http_//phonedl.ota.lenovomm.com/dls/v6/A6020a46_S048_160701_ROW_WC39DE8CCE.zip
add " : " instead of underscore " _ " after http in the link
or just copy and paste in the URL bar :- phonedl.ota.lenovomm.com/dls/v6/A6020a46_S048_160701_ROW_WC39DE8CCE.zip
Use the ota update referring to your country .
Lenovo K5 Plus Firmware (Latest)
Here is the latest stock ROM for Lenovo Vibe K5 Plus A6020a46
Release Date : 17/08/2016
Lenovo K5 Plus - Firmware A6020a46_S054_160817_16G_ROW_QPST
Download (1.17 GB)
:good:
Jintu Jose said:
QFIL was not useful for me. When I started the phone holding Volume+ button it detected the port and when clicked on the download button in QFIL the phone restarted after 3-5 seconds with blank screen, after a few seconds showed an error message "Download Fail, Port not Available". Then I had remove the battery to start my phone in the mormal mode. As I have said above, I had to approach Lenovo Service center to recover my Lenovo VIBE K5 Plus_A6020a46. They recovered it and installed the oldest OS version for it. It had many problems with that version, such as draining battery very soon and heating issues etc. I could not update it with Lenovo companion app. It downloaded the 156MB update, but during installation it showed a weird OTA error. I tried it for 5 times, but the result was always the same.
So I searched for the latest update ROM in the internet (A6020a46_S048_16070 1_ROW) I got it from an Russian Lenovo Community website. I extrated the zip file (A6020a46_S048_16070 1_ROW_QPST.zip). There were many ota update files and a "system" update file. I copied that "system.zip" file to the phones SD card and updated from there using recovery mode. It was successful.
If someone is in need of the Latest ROM (1.34 GB) for the Lenovo VIBE K5 Plus_A6020A46 go to:- http_//phonedl.ota.lenovomm.com/dls/v6/A6020a46_S048_160701_ROW_WC39DE8CCE.zip
add " : " instead of underscore " _ " after http in the link
or just copy and paste in the URL bar :- phonedl.ota.lenovomm.com/dls/v6/A6020a46_S048_160701_ROW_WC39DE8CCE.zip
Use the ota update referring to your country .
Click to expand...
Click to collapse
You're suposed to hold volume + AND volume - at the same time (just as the power button) for 5 seconds, then your phone is going to be with led and black screen.
rafaellancas said:
You're suposed to hold volume + AND volume - at the same time (just as the power button) for 5 seconds, then your phone is going to be with led and black screen.
Click to expand...
Click to collapse
:good: thank you for your help. Could you please explain it little more step by step . When should I hold both Vol + and Vol - keys together. :angel:
rafaellancas said:
You're suposed to hold volume + AND volume - at the same time (just as the power button) for 5 seconds, then your phone is going to be with led and black screen.
Click to expand...
Click to collapse
thank you for your help. Could you please explain it little more step by step . When should I hold both Vol + and Vol - keys together.
Jintu Jose said:
thank you for your help. Could you please explain it little more step by step . When should I hold both Vol + and Vol - keys together.
Click to expand...
Click to collapse
With the phone turned off and disconected from your computer, you press and hold the following buttons: volume + and - and power, for five seconds, then your phone should be black and with a red led. Now you connect to your computer and check if QFIL recognizes the port (this is the hardest part, to install and make QFIL work on windows), then it's just like the guide
rafaellancas said:
With the phone turned off and disconected from your computer, you press and hold the following buttons: volume + and - and power, for five seconds, then your phone should be black and with a red led. Now you connect to your computer and check if QFIL recognizes the port (this is the hardest part, to install and make QFIL work on windows), then it's just like the guide
Click to expand...
Click to collapse
Wow ! That worked .... thanks .... thanks a lot ... this was the key point I missed... you saved my day and phone
Jintu Jose said:
Wow ! That worked .... thanks .... thanks a lot ... this was the key point I missed... you saved my day and phone
Click to expand...
Click to collapse
I'm glad to help man
Is there any possibility to recover a dead phone? It is the same model (Lenovo Vibe K5 Plus A6020a46). It shows only red led when connected to a power source. Can't turn the power on, none of the key combinations works, no boot screen, no images nothing. It is totally dead except for the red LED.
Jintu Jose said:
Is there any possibility to recover a dead phone? It is the same model (Lenovo Vibe K5 Plus A6020a46). It shows only red led when connected to a power source. Can't turn the power on, none of the key combinations works, no boot screen, no images nothing. It is totally dead except for the red LED.
Click to expand...
Click to collapse
I don't know man, but I would try to download the QFIL image for the a6020l46 and give it a try, but, before you try it, let it charge for about 3 hours, then take off the battery and pot it on again and try to enter the mode for QFIL (volume + and - and power button pressed and hold for 5 seconds).
Same problem here
I have a bricked lenovo vibe k 5 (A6020I37) in qfil says sahara fail, and the pc recognizes my phone as Qualcomm HS-USB QDLoader 9008. From here I dont know what to do, I already tried with lenovo smart assistance but stops at 3%.
I hope you can help me to, and thank you all for your the help u can bring me.
Pleaseee anyone can help meeeee?????
A BIG SORRY for a long post. But I am sure its worth reading step by step. Because many peoples are stucked in same situation, no straight forward solution for this issue is available till now. All solutions are based on 50/50 success ratio.
I think if my issue is resolved then it can become WORLD's FIRST SOLUTION to UNBRICK NOTE 5 PRO with 100/100 success ratio.
About Me: I am an ordinary Android user since years. I know how to root and install TWRP and Custom ROMs on any Android Phone. I am not a Developer, every thing discussed here is purely gained by experiments by playing with my phone.
After playing with my bricked phone I reach at a point where I am hopeless and I think at this stage a Developer can help me only, who have deep knowledge of android OS. That's why I called Devs to help me.
About Phone I have Note 5 Pro Global (whyred)M1803E7SG. Phone is under warranty but unfortunately Front Glass of my phone is broken few months ago but still working, so Mi Service Center refused to accept my phone under warranty due to broken Front Glass. Tried to repair my phone by a local Phone Service Shop, thay have all professional tools like UMT, Avangers, MedusaPro etc. but they were also unable to repair my phone. Now I have no option left other than I should repair it by myself.
Phone was on ARB4, was working fine. Bootloader Unlocked and I have rooted it long time ago and was playing with it since it is rooted by flashing different Custom ROMs on daily basis.
Currently phone was working fine on Masik X 4.1 ROM. Some days ago I flashed Masik X 5.0 ROM via TWRP on my phone and after reboot phone became dead and went to EDL 9008 mode. I noticed that I flashed Masik X 5.0 for Note 6 Pro (tulip) ROM on it mistakenly.
Journey Stats Here:
1 - After bricking my phone I tried to flash fastboot ROM for whyred in EDL mode, phone flashed successfully but still stucked in EDL mode. Tried all fastboot ROMs from ARB2 to ARB4 but still no sign of life, phone was not coming out of EDL mode. Also tried "test anti4.zip" files as well but phone is still in EDL mode after a successful flashing.
2 -After that I tried to flash fastboot ROM of Note 6 Pro (tulip) in EDL mode, after flashing complete when I tried to turn ON my phone, I noticed that phone try to start with vibrate and charging light blinks for a while but nothing on Screen and phone dead again. I checked with USB cable attached to laptop, nothing appear in Device Manager. Here I opened my phone and bring it to EDL mode via Test Point method.
3 - Then after searching on internet I saw on a forum where another person was in same situation. He mentioned his phone display was turning ON on a Mi 6X (wayne) ROM but with "Press any key to shutdown" message on screen. So tried same with Mi 6X (wayne) ROM. Phone is turning ON with "Press any key to shutdown". So I started playing with Mi 6X ROM. I started replacing Mi 6X ROM file with Note 5 Pro files one by one and flashing my phone again and again with every one new file (took so many hours in playing with my phone:crying. Initially had many issues like: missing keymaster64.mbn file as Mi 6X uses keymaster64.mbn but Note 5 Pro is using keymaster.mbn file (so corrected .xml and .bat files according to need), Unable to mount Persist partition in TWRP (corrected it by terminal method in TWRP by using command "make_ext4fs /dev/block/bootdevice/by-name/persist", phone was going to Fastboot for a while, Not going to recovery mode, No USB detection on laptop in Device Manager. Fastboot lasts for a half second and then phone goes off.
In short at the end finally I noticed only three files "abl.elf, pmic.elf, xbl.elf" from Mi 6X ROM are responsible for turning my phone ON.
4 - So I replaced "abl.elf, pmic.elf, xbl.elf" files from Mi 6X ROM with Note 5 Pro ROM files and flashed my phone with this new modified ROM in EDL mode. Phone turned on without any "Press any key to shutdown" message on screen. Now phone can go to fastboot mode and detected on USB on my laptop. But not going to Recovery mode, after pressing Vol UP + Power Button, only a black screen and nothing happening on my laptop Device Manager (no driver at all). In fastboot mode I flashed "PitchBlack-whyred-2.9.0-20190501-1030-OFFICIAL" recovery (initially I tried TWRP Recovery for whyred but in TWRP phone was not detected as MTP device on my laptop, so I used Pitchblack Recovery) and after issuing boot command to recovery.img I can go to Pitchblack recovery mode, phone detected on USB port as "Note 5 Pro", MTP drive appear in My Computer, I can copy/paste files in phone Storage. In Recovery mode I flashed Official "miui_HMNote5Global_V10.3.1.0.PEIMIXM_d4d2c9f2aa_9.0" ROM. Phone flashed successfully but after reboot phone went to EDL mode again. So I revived it again with modified ROM.
5 - After revival I tried to boot phone in normal way, I noticed that MI Splash screen is blinking with behavior: Splash screen appears fine for a while and on second blink Screen is inverted then 3rd blink Screen fine and 4th blink screen inverted and so on till I reach to MIUI10 welcome screen. On welcome screen the behavior is same like once fine then inverted. But here my touch screen is not working, I can't go after this screen. Phone is not allowing to touch Next button. I can charge my phone with charger connected. Phone detected as "Note 5 Pro" on my laptop.
6 - I rebooted phone to fastboot mode, tried to flash "whyred_global_images_V10.3.1.0.PEIMIXM_20190522.0000.00_9.0_global_8201319a7e" with MiFlash but can't flash due to "Product Mismatch" warning by MiFlash. Tried Mi 6X ROM and MiFlash started flashing fine.
7 - Then I flashed "boot.img, recovery.img, cust.img, system.img" files by using fastboot flash xx xxx.img commands for Note 5 Pro. Fastboot flashed all files successfully. But after rebooting phone behavior is same like blinking inverted screen and touch not working.
8 - Now I am helpless at this stage. Tried all ways to revive my phone. Nothing else is remaining as I think. No other file is remaining which I can try.
HELP REQUIRED FROM A Developer
I reached on a stage where my phone is now "Semi Unbricked" but is still useless for me. But I hope some Developer can help me to revive my phone.
My Note 5 Pro is converted to Mi 6X but touch screen is not working. Screen is working fine in Pitchblack Recovery mode, phone is responding in Fastboot mode but as it is the fastboot mode of Mi 6X on a Note 5 Pro so it is useless for my phone.
Kindly assist me further so I can replace Mi 6X fastboot with original Note 5 Pro fastboot so that I can flash Note 5 Pro ROM on it.
Waiting for a very positive and prompt reply.
Regards!
Any body knows about display/touch driver files inside Android OS???
My touch screen is not working at all on MIUI Welcome screen. I want to embed Display Driver files in ROM so I can go forward ahead of this Welcome Screen.
I have tried so many ROMs from different Xiaomi models, replaced so many files one by one, spent too much time on doing this all. But the only combination of files works mentioned below:
abl.elf (must be from wayne ROM)
pmic.elf (must be from wayne or tulip ROMs, both working)
xbl.elf (must be from wayne ROM)
All other files from whyred ROM are OK to flash to bring my phone alive.
ROMs Used:
whyred_global_images_V10.3.1.0.PEIMIXM_20190522.0000.00_9.0_global_8201319a7e
wayne_images_V10.3.3.0.PDCCNXM_20190514.0000.00_9.0_cn_1d4725ac4d
tulip_global_images_V10.3.2.0.PEKMIXM_20190426.0000.00_9.0_global_2264f9bd86
Now I concluded all this mess as: I can never go back to whyred original ROM. The only way left is to use my phone as a Mi 6X by name if touch screen of my mobile gets start working.
Some body please help me in replacing Display Driver files of whyred with wayne files.
Kindly assist me to pass through this step. I want to see what's working and what's not after MIUI Welcome Screen. e.g. IMEI, BT, WIFI, SOUND, CALL etc......
Please help
My phone was rooted and I was on Havoc os v2.2 , I was using it for 2-3 months and os was running very great, but suddenly it started giving me problems like recent tabs were not opening, notification panel were not opening.
So I thought to install different rom, I downloaded evolution x v4.4 and to install it, I updated my twrp recovery from v3.2 to v3.4 and it got successfully updated, but when I try to open recovery it got stuck on mi logo, so I tried to flash recovery again with the help of pc, but on command prompt when I type adb devices, device doesn't appear, so I tried to open developer options but the option doesn't appear so I tap multiple times on build number, but still nothing happens.
So I tried to format my phone , but now it got stuck on mi logo, neither the device is booting even in recovery mode it stuck on mi logo.
So what are the option left for me to get out of this situation.
Edit: and in device manager it is showing as Kedacom usb device and under it is showing Android Bootloader Interface.
Nevermind I figured it out myself
If you want to flash recovery, lock/unlock bootloader or root your phone or flash a stock rom then just download this software.
Link : Tool all in one https://forum.xda-developers.com/on...ol-one-driversunlocktwrpfactory-t3398993/amp/
(Credit goes to developer @mauronofrio)