Related
Never seen or heard about anything like this. I wonder if anyone encountered a similar situation.
I have a good reason to believe my phone is not bricked, although I'm not sure which is worse.
I'm not sure if it's related, but it might be worth mentioning here:
I noticed, since I started using this phone, that the battery level sometimes drops very fast. Normally the phone maintains normal battery level, but while opening "heavy" applications (e.g waze, google earth) or even during a phone call, It drains the battery out rapidly, roughly about one percent per two minutes. Sometimes even while connected to charger the phone shows a slight decrease in battery level. And it gets hot too.
Few hours ago, I turned it off to save some battery for afterwards, and since that moment it wont turn on. I tried several things.
I left it to charge.
I took the battery out and placed it back after a while.
I tried all possible combinations of the three physical buttons on the device.
I took out the sim card and the sd card.
At home I checked the battery, It shows normal voltage of 4.1V. I used several usb cables and measured the voltage between the battery connector inside the phone while the battery is removed. It indicates that the phone keeps charging the battery even while staying in this situation.
While plugging it to the computer, the phone is not even identified by it. It wont react to the computer just as if it's not connected at all.
Getting it to usb mode showed no result.
I have installed new roms on the device several times, yet more than a week has passed since the last time, and the phone worked fine since. except for the battery issue that I mentioned.
It was originally bought from T-mobile without contract, and it has a warranty assuming I would be able to bring it back to stock rom. Anyway, I'm using this phone in Israel and the nearest T-mobile service point is 10,000Km away, so I would do this as a last resort.
Hope for some advice, and may this post be able to help others that got in to similar situation.
Have you tried getting it into download mode? Disconnect from the PC, then keep both volume buttons + power button pressed while connecting the USB cable to the PC.
Sent from my SGH-T989 using xda premium
Phone won't turn on
Just had this same experience. I had just taken mine off the charger in the morning, booted it up and minutes later, it restarted on its own. Never came back to life. No possible combination of buttons, batteries, usb cables, ODIN running/not running would bring my phone to life. I mean I tried everything including the famous usb jig. Nothing. Sent it in to TMo and as it was within 30 days, they sent a new one which is running fine.
The problem is...
The phone is not recognized by any device, while being connected to usb. The only thing it does while plugged is to charge the battery, and that I can tell by measuring the voltage. It gives no visual indication, or respond to any button\connected device. Using that jig is the only thing I got left to do. I know it suppose to reset the counter. What else will it restart? My rom?, internal sd? the recovery partition? Can this physically damage the components on the phone's PCB?
And assuming the phone hardware is unharmed, are there any firmware malfunctions which are impossible to repair? (Generally I know there are, yet I'm asking specifically for these phones that comes with "download mode")
Had a situation where the device wouldn't turn on. Woke up one morning and it was still on the charger yet totally unresponsive.
Pulled the battery, waited 30 seconds and everything was fine.
Sent from my Hercules using XDA App
I wish it was that way for me too, yet it was one of the first things I tried. and yet, Nada. Here are some news: I gave the jig a try, and it didn't seem to work either.
On contrary to most of the fully bricked cases I heard about, my phone wont be recognized by the pc at all while being connected to usb. Not even a "Faild to connect" message. That leads me to believe that it is either a dead Boot-loader or a hardware malfunction.
I made a little research, and found out that it is possible to connect the pc through some kind of adapter directly to phone's processor, using specific pins. It is a simple kind of serial connection called Jtag. Initial factory configuration of electronic devices is only one application of it.
For that process I need to have that device along with it's driver, a boot loader to flash (According to what I've seen the T989 is not yet supported by these softwares).
I need to have some nerves to open up my device and to solder some pins (And I also need that Jtag pinout).
Does anyone know about a better way of doing it other than sending the phone half world to the U.S?
pins for connect
Uploaded with ImageShack.us
currently not supported by any unofficial service except US T-Mobile ... or Samsung US
I've seen this problem mentioned before, but no good fixes.
My phone won't charge while on, but will when off. Charging has always been a little buggy, but now seems stuck this way.
The problem seems to keep my phone from connecting to the computer - neither the mac android download program will recognize the phone, nor will it charge off the computer, nor will the wugfresh tool see it when plugged into my PC.
I rooted/unlocked using the wugfresh tool (kept the stock ROM) and figure I need to warranty replace the phone - but because the computer won't recognize it, I don't know how to un-root/re-lock it.
Question - 1. anybody know how to fix my usb charging/recognition problem? 2. assuming not, is there a way to un-root/re-lock the phone without needing to plug the phone into a computer?
Thanks very much!
Does it charge with the phone on from AC? And when it's plugged up to your mac, does it have the thing in the notification bar saying its connected?
It's possible you have a bad cable, just to eliminate the easy fix first. It should charge fine with any mini USB charger.
If you can get it to charge from AC, I'd try a different computer if possible or if not maybe a re-install of the drivers.
Next, as maybe a last ditch effort, it's possible the ROM got corrupted, though I'm not sure how likely that would be. I'm sure you can get the stock ROM to flash in Clockworkmod but the only way to re-lock the bootloader that I know of requires a PC.
Maybe someone else can chime in weather or not Samsung actually cares if you're unlocked when it comes to a warranty for a hardware problem. Also, what carrier do you have? They may just give you a new phone themselves and again, maybe someone can tell you if they actually look at whether you've modded your phone.
Thanks for the reply.
Yes, when it's hooked up to an AC adapter and the phone is ON, I get no charging. When the phone is on and hooked up to a computer (both PC and mac), I get no charging. No upper right hand corner battery indicator change.
In fact, when the phone is off and hooked up to AC power, it seems to be hit-and-miss as to whether or not it actually charges.
Plugged into a computer, I get nothing - it doesn't register a device is attached at all.
I think that's a great question - if you return an un-locked phone, do they definitely get mad at you? I wonder if that's been asked in the forums before...maybe I'll make a different thread?
Also, from clockworkmod, how can I flash the original rom, as you suggested?
I've already factory re-set the phone and even flashed a different ROM just to see what would happen - and it didn't fix the charging issue.
Try this https://play.google.com/store/apps/details?id=eu.chainfire.mobileodin.pro
Sent from my Galaxy Nexus using xda premium
I literally had this exact issue over the weekend where it would charge when powered off but then the USB would completely die when the phone was turned on. All after using my incar charger. It seems the port inside the phone got bent so that the board inside was almost touching the bottom of the phone. If held flat on your palm...
I fixed it by bending the board back up with a knife so its dead in the middle of the port. No problems charging now.
this exact problem has been an issue for me as well, contacted Samsung and told them i bought it second hand and they issued a rma and sent me a ups label t send it in. This is my first phone that broke before I even had a chance to root it. I was pissed at Htc so decided to try something new. Going back to my T-Bolt for a while now.
My phone charges sometimes, others it doesnt. Sometimes the "Nintendo blow" works, other times it requires force. Eventually I can always get it to charge, but it can take a half hour of playing with it. I have multiple cables, original Samsung batteries, and lots of experience inside phones, and have never had an issue that I couldnt FULLY determine was hardware or software. Samsung claims they have never seen this issue. lol. Obviously they dont visit the forums
cymru said:
I literally had this exact issue over the weekend where it would charge when powered off but then the USB would completely die when the phone was turned on. All after using my incar charger. It seems the port inside the phone got bent so that the board inside was almost touching the bottom of the phone. If held flat on your palm...
I fixed it by bending the board back up with a knife so its dead in the middle of the port. No problems charging now.
Click to expand...
Click to collapse
great idea - i was using my car charger this weekend. i'll give it a shot.
update - i bent the little board up off the bottom, and now i can't fit the charger in it. uhoh.
This is becoming a bigger and bigger issue. Please star and/or comment on this issue: http://code.google.com/p/android/issues/detail?id=23789
I sent my galaxy to Samsung 2 weeks ago, it is due to arrive back today. They paid postage each way and the invoice says they replaced a component (no detail) and updated software and prl. I was already on the current release so not sure what to expect. But it is good to know they are taking care of us.
Hi there,
I apologize if there is already another thread for this kind of issue but I really have no idea where else to post this. I am a complete newbie when it comes to phones but would like to know if there is anyway to help me solve my problem:
My phone is a galaxy nexus with I believe 4.2.2 JB. I've always had problems with my phone randomly resetting/crashing and wasn't able to find any solution to this problem. However, today when I was out shoveling snow on my driveway, I realized my phone was a little wet as I forgot to zip up my pocket and so my phone reset (remained on the Google) screen and would not boot up (It happens quite frequently that I thought it was just like any other reset). So I was a little impatient and took out the battery. When I tried to turn the phone back on, the power button was completely unresponsive. I thought I'd give it a second, take out the battery and sim card and reboot it but to my surprise nothing happened. I ended up looking through the forums for some solution to my problem but I don't know where to begin and what to do.
I have tried the method of plugging in the USB cable into the phone (without battery) and putting it back in. The phone is still unresponsive and to add insult to injury when the phone is plugged in the USB cable to the PC, the PC does not recognize the phone and keeps beeping (the kind that lets you know its disconnected or just cannot read the device). Right now the phone is in a bag with rice just to make sure that the phone had not suffer any water damage, but even when it was in my pocket it wasn't extremely wet..
I believe it may be the device but am not sure what actions I can do on my behalf to solve the problem. Is my phone completely gone or is it still able to be saved? Would I need to bring it into a specalist to see if they can help me out or can I do this myself? Any help is greatly appreciated and thank you for taking the time to read!
Cheers!
Edit:
Also just received an OMAP4440 while phone was plugged in... Does that mean my phone is done?
Any help?
thebeatlesdcp said:
Hi there,
I apologize if there is already another thread for this kind of issue but I really have no idea where else to post this. I am a complete newbie when it comes to phones but would like to know if there is anyway to help me solve my problem:
My phone is a galaxy nexus with I believe 4.2.2 JB. I've always had problems with my phone randomly resetting/crashing and wasn't able to find any solution to this problem. However, today when I was out shoveling snow on my driveway, I realized my phone was a little wet as I forgot to zip up my pocket and so my phone reset (remained on the Google) screen and would not boot up (It happens quite frequently that I thought it was just like any other reset). So I was a little impatient and took out the battery. When I tried to turn the phone back on, the power button was completely unresponsive. I thought I'd give it a second, take out the battery and sim card and reboot it but to my surprise nothing happened. I ended up looking through the forums for some solution to my problem but I don't know where to begin and what to do.
I have tried the method of plugging in the USB cable into the phone (without battery) and putting it back in. The phone is still unresponsive and to add insult to injury when the phone is plugged in the USB cable to the PC, the PC does not recognize the phone and keeps beeping (the kind that lets you know its disconnected or just cannot read the device). Right now the phone is in a bag with rice just to make sure that the phone had not suffer any water damage, but even when it was in my pocket it wasn't extremely wet..
I believe it may be the device but am not sure what actions I can do on my behalf to solve the problem. Is my phone completely gone or is it still able to be saved? Would I need to bring it into a specalist to see if they can help me out or can I do this myself? Any help is greatly appreciated and thank you for taking the time to read!
Cheers!
Edit:
Also just received an OMAP4440 while phone was plugged in... Does that mean my phone is done?
Click to expand...
Click to collapse
The same consequences, came to my gnex, when I cleaned it, with too much liquid... Now the most unprotected parts from water of the phone are the usb port, of course, and the power and volume button. To solve, you have to open the phone (http://www.ifixit.com/Teardown/Samsung+Galaxy+Nexus+Teardown/7182) and clean the contacts of the power button, for the usb port, you have to replace all the part for a few $ on ebay... (http://www.ebay.com/itm/Samsung-Gal...e_Replacement_Parts_Tools&hash=item2c66d9064b)
Use at you own risk:
A friend of mine was kayaking and had his Samsung galaxy s3 dunked in the water for a while. it was totally wet and the screen wouldn't run on at all.
He baked t in the oven at 200 F for a couple of hours and things went back to nornal. he also stated that he has done that before and it worked every time.
Think of this as a last resort if you are unable to change the usb ribbon as stated above. Also make sure you google this solution extensively to get the right temp and the right amount.
Good luck.
Background: I was flashing a backup via TWRP, which failed because it could not write to memory. I rebooted the phone and it no longer responded.
Currently: the phone only has a blinking red LED whenever the USB cable is connected. I cannot connect into fastboot. The phone does not respond or do anything. No vibrations.
Is there any possible way to fix this? Or am I screwed?
Been there. No button combinations work nor vibrates at all. PC sees the device, but it is unrecognized. The LED flashes, but that's it. In the end it was power problems, battery and motherboard had lost communication with each other somehow. Thankfully the phone was under warranty and they swapped the mobo.
Koostis said:
Been there. No button combinations work nor vibrates at all. PC sees the device, but it is unrecognized. The LED flashes, but that's it. In the end it was power problems, battery and motherboard had lost communication with each other somehow. Thankfully the phone was under warranty and they swapped the mobo.
Click to expand...
Click to collapse
Thanks for the reply. You think they'll be able to find out (or be bothered to find out) that I unlocked the bootloader? Standard rooting = no warranty problems :\
I guess it depends on how much they want to find out. Although I believe it's pretty much impossible to find out anything if your mobo is dead unless they do some really complicated soldering, which I doubt they would.
Thanks for your help! We'll see how this goes once I get back from holidays. Also, what excuse did you give to justify the phone getting sent off?
Well my case was a little different: I bought the phone second-handed and the guy told me that nothing had ever been done to it (no rooting, no bootloader unlocking or whatsoever). However I found out that it had been and still was rooted, so I recycled it via Sony companion and charged it fully afterward. 5 minutes later it died. When I went to the service center, I didn't tell them much, nor did they ask much. "The phone went to sleep and never turned on again" had enough justification for them. Hope it's enough for you as well.
I had this issue when my phone got water damaged. I left it plugged in for a few hours and it would boot after, though the backlight was dead due to the aforementioned water damage. It might work for your phone.
Hello!
Well, I had the really bad luck of a very bad hard brick... my xperia was on low battery (around 15%) the last time that I use it, then around 20min later I got it and try to check, but screen didn't turn on, and the Led was blinking White color, since I deal in the past with this issues (around 3 or 4 times), I connect the usb cable to power adapter and simply did the reset button under sim flap, and my phone made the normal 3 vibrations, so, I hope that everything was fine, however, after that, I simply try turn on it, but never happen, No led of charge, no more vibrations and no power on, no signal of operation at all... so, I test remove and reconnect the usb cable and nothing, so, I try make another sim flap reset button test, but at this time and until now, no more 3 vibrations response and nothing else... and now, after reading some many posts, and try everything suggested in other posts about I really sad and hope for some help or feedback, if somebody may help...
By now I tested on my windows 7 notebook, and at first the phone was not recognized by drivers however it shows the bad message QHUSB_BULK error usb device, in later attempts, I made after some buttons tests looking for some response I got the phone change the messague, at the moment of connect it with usb cable to my pc, it was recognized as SEMC Flash Device... In both cases windows didnt allow or recognized for a proper driver installation....
But after other attempts, I lost the SEMC Flash Device status, and by now not remember what I did to get this mode or if it may be of some help...
By now I am really worry, since I got my phone from Hong Kong, and it came and worked fine until today, but in my country there is no service for this model since it not still on sale at official dealers/ carriers, and I believe that I don't have warranty service (since is an international purchase and not on local dealer) and also because I Unlock Bootloader for getting root and Sony records that information for warranty purposes (since I unlocked BL, I installed TWRP then I installed the romAUR custom rom and I upgraded it to 1.25 version with last kernel available from the same rom thread but thas was a month ago and phone worked fine after all custom rom installation)...
By now, I would like to ask if may be possible please, some guidance and help...
1) I was made attempts by the last 6 hours after brick without luck, and I wonder and suppose that the battery may be very low, but since I don't get any charging led, I wonder if by left It connected to the original sony charger with original sony cable (almost new and working both, and also tested both with other cell), my bricked phone may still get some charge on the battery.... somebody konws if possible to charge an xperia bricked?... I wonder/hope about that, if may be a charged battery may help in got the 3 vibes reset again that I hope may fix the issue and return my phone to boot...
2) Since seems that i don't have chance to get repair service on warranty since I unlocked my phone (and in my country the cost service for such model could easily be so high as almost a new phone), and also low chance for a warranty replacement from seller, I wonder about take the chance of open it and try to remove battery connector at a last resort since , I may suppose that this may allow for clear internal electrical charged registers of system and may allow me for a reset, but I wonder if the white flap sim buttons really did the same, that is simply open the battery connections, but, I doubt about that, since in this procedure the cel made 3 vibes and the energy for the vibes need to come form a connected battery...
3) May somebody with more luck, knowledge and experience, may suggest or share some help or advice about this issue...
I am a long time cell phone fan and long time in the issues of unlocking and installing custom roms, but until today, and after I survived many other phones bricks, my highest and loved phone of all my time, is bricked in a way that I am start to desperate, since I almost no clue by now about what could I try looking for a fix....
So, thanks in advance and if some body may help, I would be very grateful....
Is there really a reset button under the sim flap? Maybe you damaged the internals when trying this..
slayerz said:
Is there really a reset button under the sim flap? Maybe you damaged the internals when trying this..
Click to expand...
Click to collapse
Yes, I've used it many times it's highly unlikely to damage it from that. Unless you press it harder than a gentle touch.
Sent from my E6653 using Tapatalk
Yes, there it is, well, by now I am collecting more info and try about fully discharge my phone in order to get a RED permanent charging Led light (for future reference, seems that a Pulsing RED charging led means NO detection of battery...), by no today at morning I put my phone on charger and it only warn a little, and according with some info, the best chance by now is to plug it for a long time (other models of xperia reports around wait 24+ hours for get a RED permanent light...)
By now, I already purchased a set of adhesive gaskets, in preparation to open my phone (I did in the past and have some skills for doing it, but not that I really like to do over a so new and expensive phone... ), since by now, if I fail in got a RED permanent charging light, seems that the next step is to open back cover a remove battery connector, plug in usb cable connected to wall charger and then after 3 minutes wait, reconnect battery connector with the usb cable still attached, this would reset a really brick phone, and suppose tho reset the charging process of xperias...
By now, and in case of help other people that may need it now or in future, the guide that I am following advice is this:
[GUIDE] Recover 2012 and newer XPERIAs from SOFT-brick
http://forum.xda-developers.com/showthread.php?t=1849170
The info in the page seems with lots of sense, and the charging process description seems very similar at I would believe could be used in my previously Z2 and my now in comma, Z5P.... But by now, I need to get a RED light in order to try to unbrick without need to open back cover glass....
Any info, advice, comments or better, experience share, would be very gratefull...
Best regards...
Did you ever solve the problem? My Z5 died and wont turn on. Flashing lights when the usb is plugged in. Tried unplugging the battery and charging for hours
you have no fastboot ( vol+ blue led ) and no flashmode ( vol- green led )?
No, only a flashing red light when plugged in. The phone dos not react to any buttons.
Sony Xperia Companion does not recognize the phone.
"lsusb" in linux shows nothing when i plug the phone in.
xaser66 said:
Hello!
Well, I had the really bad luck of a very bad hard brick... my xperia was on low battery (around 15%) the last time that I use it, then around 20min later I got it and try to check, but screen didn't turn on, and the Led was blinking White color, since I deal in the past with this issues (around 3 or 4 times), I connect the usb cable to power adapter and simply did the reset button under sim flap, and my phone made the normal 3 vibrations, so, I hope that everything was fine, however, after that, I simply try turn on it, but never happen, No led of charge, no more vibrations and no power on, no signal of operation at all... so, I test remove and reconnect the usb cable and nothing, so, I try make another sim flap reset button test, but at this time and until now, no more 3 vibrations response and nothing else... and now, after reading some many posts, and try everything suggested in other posts about I really sad and hope for some help or feedback, if somebody may help...
By now I tested on my windows 7 notebook, and at first the phone was not recognized by drivers however it shows the bad message QHUSB_BULK error usb device, in later attempts, I made after some buttons tests looking for some response I got the phone change the messague, at the moment of connect it with usb cable to my pc, it was recognized as SEMC Flash Device... In both cases windows didnt allow or recognized for a proper driver installation....
But after other attempts, I lost the SEMC Flash Device status, and by now not remember what I did to get this mode or if it may be of some help...
By now I am really worry, since I got my phone from Hong Kong, and it came and worked fine until today, but in my country there is no service for this model since it not still on sale at official dealers/ carriers, and I believe that I don't have warranty service (since is an international purchase and not on local dealer) and also because I Unlock Bootloader for getting root and Sony records that information for warranty purposes (since I unlocked BL, I installed TWRP then I installed the romAUR custom rom and I upgraded it to 1.25 version with last kernel available from the same rom thread but thas was a month ago and phone worked fine after all custom rom installation)...
By now, I would like to ask if may be possible please, some guidance and help...
1) I was made attempts by the last 6 hours after brick without luck, and I wonder and suppose that the battery may be very low, but since I don't get any charging led, I wonder if by left It connected to the original sony charger with original sony cable (almost new and working both, and also tested both with other cell), my bricked phone may still get some charge on the battery.... somebody konws if possible to charge an xperia bricked?... I wonder/hope about that, if may be a charged battery may help in got the 3 vibes reset again that I hope may fix the issue and return my phone to boot...
2) Since seems that i don't have chance to get repair service on warranty since I unlocked my phone (and in my country the cost service for such model could easily be so high as almost a new phone), and also low chance for a warranty replacement from seller, I wonder about take the chance of open it and try to remove battery connector at a last resort since , I may suppose that this may allow for clear internal electrical charged registers of system and may allow me for a reset, but I wonder if the white flap sim buttons really did the same, that is simply open the battery connections, but, I doubt about that, since in this procedure the cel made 3 vibes and the energy for the vibes need to come form a connected battery...
3) May somebody with more luck, knowledge and experience, may suggest or share some help or advice about this issue...
I am a long time cell phone fan and long time in the issues of unlocking and installing custom roms, but until today, and after I survived many other phones bricks, my highest and loved phone of all my time, is bricked in a way that I am start to desperate, since I almost no clue by now about what could I try looking for a fix....
So, thanks in advance and if some body may help, I would be very grateful....
Click to expand...
Click to collapse
I know you probably have but did you try holding volume up and power to force reset it?
You say you couldn't get a proper installation of hardware, so the computer can see the device? Is it showing an exclamation point next to the device driver?
---------- Post added at 04:27 PM ---------- Previous post was at 04:15 PM ----------
I know you probably have but did you try holding volume up and power to force reset it?
You say you couldn't get a proper installation of hardware, so the computer can see the device? Is it showing an exclamation point next to the device driver?
Edit: Go to device manager and right click phone and do update drivers.
Click browse for update yourself and direct it to WINDOWS/INF folder and check "include subfolders".
Then click where it says "let me pick from a list of device drivers on my computer"
Then click Android phone from the list and click MTP USB driver and click OK for install.
Your phone should be installed correctly.
Then try fastboot etc.