Hello everyone. I'm new here. I don't know if there is a topic similar with my issue but my smartwatch sony 3 can't connect with the internet and with the android wear app. Yesterday it was working well with my android tablet, but then I pair with another android smartphone and I can't connect it again with my tablet. It says on the smartwatch that is connected but then it shows "Just a minute..." and on the android tablet "checking for updates... this may take a few minutes". After a few minutes it shows on the smartwatch "can't connect to the android wear app on your phone. Swipe for some tips."
I have done the downgrade of the smartwatch to LWX48P version because I want to update to LCA43 to use NFC with freestyle libre because I am diabetic. Please help me, and thank you so much for your patience.
Best regards from Portugal,
Catarina
Greetings. Perhaps the problem you are having is the switch. Your watch can only be connected to one host device (phone/tablet) at a time. In order to switch you need to disconnect it from the device and set it up as a new device on the new one. This will trigger a wipe (at least of /data). There may be an app to make the switch easier, but I am not sure.
Good luck.
~Leko
Sent from my SM-T810 using Tapatalk
Catarina Pina said:
Hello everyone. I'm new here. I don't know if there is a topic similar with my issue but my smartwatch sony 3 can't connect with the internet and with the android wear app. Yesterday it was working well with my android tablet, but then I pair with another android smartphone and I can't connect it again with my tablet. It says on the smartwatch that is connected but then it shows "Just a minute..." and on the android tablet "checking for updates... this may take a few minutes". After a few minutes it shows on the smartwatch "can't connect to the android wear app on your phone. Swipe for some tips."
I have done the downgrade of the smartwatch to LWX48P version because I want to update to LCA43 to use NFC with freestyle libre because I am diabetic. Please help me, and thank you so much for your patience.
Best regards from Portugal,
Catarina
Click to expand...
Click to collapse
Just a hunch, but you probably need to disconnect it from Android Wear on both devices, then remove Bluetooth pair from both devices in Bluetooth settings, then reset the watch to factory settings, then start with a clean slate.
But previous poster is correct, you cannot pair it with 2 devices, which is really annoying, so pick one device only, and you can't switch from one to the other, and then back again.
admisi said:
Just a hunch, but you probably need to disconnect it from Android Wear on both devices, then remove Bluetooth pair from both devices in Bluetooth settings, then reset the watch to factory settings, then start with a clean slate.
But previous poster is correct, you cannot pair it with 2 devices, which is really annoying, so pick one device only, and you can't switch from one to the other, and then back again.
Click to expand...
Click to collapse
Thank you so much for your reply! It works if the smartwatch has the latest version ! But the main question is that with the LWX48P version I can't connect with my tablet. But I need to update to LCA43, and without internet I can't do it. I searched for a OTA version of LWX48P to LWX49K to LDZ22D and finally to LCA43 to make the upgrade manually but I can't find it. Can you help me please? Thank you!
Catarina
Related
I find it hard to believe I'm the only one who likes my M360 syncing with my tablet when I'm home, and with my smartphone when I'm out. There is actually no official way to pair the M360 with multiple Android devices at the same time, but I have, however, figured out an alternative. I am going to assume that you already have it paired to one device. If not I believe there are other threads out there to help you with that!
Steps:
In the Android Wear official app, tap the watch icon on the translucent black bar atop the screen to disconnect the M360 first
Check to make sure that underneath the name of your device, the status reads "Not connected"
Go to the watch settings, and reset the device, yes unfortunately there is no way around except factory resetting first
Now go through the original instructions upon boot making sure that this time you pair it with your OTHER Android device
Follow the first two steps again after the device has been paired successfully and booted up
Congratulations! The M360 should now pair with the two devices one at a time after being disconnected from one another!
Hope this helped you guys, as this method definitely works for me with my Nexus 7 (flo) and Galaxy SIII (SGH-I747)!
Doesn't work as of now, using a Google Nexus 10 tablet and Sony Xperia Z2 smartphone. Whichever device is paired last works fine. The other device will manage a pairing request just fine after disconnecting the first one, but once that pairing request is approved, it will sit forever on the "Connecting..." status, and never actually connect.
Is this every watch? I use 2 phones every day because my work does not allow camera phones. I think not being to connect to 2 devices at this junction of tech should not be a handicap.
is it possible to install RunKeeper on moto 360 and upload all activity to my profile?
shoman94 said:
Is this every watch? I use 2 phones every day because my work does not allow camera phones. I think not being to connect to 2 devices at this junction of tech should not be a handicap.
Click to expand...
Click to collapse
Yes this is an Android Wear limitation, not a Moto 360 one.
thebobmannh said:
Yes this is an Android Wear limitation, not a Moto 360 one.
Click to expand...
Click to collapse
What a stupid limitation. Thanks for the reply. :good:
shoman94 said:
What a stupid limitation. Thanks for the reply. :good:
Click to expand...
Click to collapse
I second that opinion. I just learned of this yesterday when I got my Moto 360. I have been using SmartWatch 2 before and figured that Android Wear being so much newer and with more features it would allow me to connect it to multiple devices... well, crap.
Is the situation same even with the new 5.1.1 version of Android Wear? Google *still* doesn't let us connect to multiple devices?
(And iOS doesn't even have the Android Wear app.. you'd think we live 15 years in the past with these stupid limitations...)
No this limitation has not changed.
so do i have to connnect everytime that i leave one device behind within the app? Bc they both wont stay connected its one or the other??
I find it hard to believe I'm the only one who likes my M360 syncing with my tablet when I'm home, and with my smartphone when I'm out. There is actually no official way to pair the M360 with multiple Android devices at the same time, but I have, however, figured out an alternative. I am going to assume that you already have it paired to one device. If not I believe there are other threads out there to help you with that!
Steps:
In the Android Wear official app, tap the watch icon on the translucent black bar atop the screen to disconnect the M360 first
Check to make sure that underneath the name of your device, the status reads "Not connected"
Go to the watch settings, and reset the device, yes unfortunately there is no way around except factory resetting first
Now go through the original instructions upon boot making sure that this time you pair it with your OTHER Android device
Follow the first two steps again after the device has been paired successfully and booted up
Congratulations! The M360 should now pair with the two devices one at a time after being disconnected from one another!
Hope this helped you guys, as this method definitely works for me with my Nexus 7 (flo) and Galaxy SIII (SGH-I747)!
have you tried Beelink?
https://play.google.com/store/apps/...utm_source=42matters.com&utm_medium=WidgetWeb
nightfishing said:
have you tried Beelink?
https://play.google.com/store/apps/...utm_source=42matters.com&utm_medium=WidgetWeb
Click to expand...
Click to collapse
Old thread, but for the benefit of others who may find this, the dev has unpublished the Beelink app. It appears that the 4.4W.2 Android Wear update broke the app.
It's now 2 years later, has anyone found a way to connect to 2 devices at the same time? I need to get notifications from personal and work phone at the same time on my M360...
I don't think it is possible, but you can sync notification from one phone to other via pushbullet or similar app. This way can get all notifications on the watch as well.
Hi All,
I have receive for Christmas a SW3.
I already have a LG G2 (D802) running Lollipop :
http://forum.xda-developers.com/lg-g2/development/rom-liquidsmooth-v4-0-lg-g2-t2948395
With Render Kernel :
http://forum.xda-developers.com/lg-g2/development/kernel-render-kernel-aosp-lg-roms-t2803929
I have update the SW3 to official 5.0.1 with PC Companion.
Then install Android Wear from the market on the phone :
https://play.google.com/store/apps/details?id=com.google.android.wearable.app&hl=fr
I had "Sleep as Android" app already installed on the phone before get the watch.
I have connect the watch to the phone then I have try to install different apps as :
https://play.google.com/store/apps/details?id=com.npi.wearminilauncher
and
https://play.google.com/store/apps/details?id=com.appfour.wearbrowser
Without problem, the apps appear on the watch., "Sleep as Android" too.
But now, I can't success to install any other apps. I have try :
https://play.google.com/store/apps/details?id=rocketstartups.wearcalculator
Or
https://play.google.com/store/apps/details?id=co.hoomi.athere
But the apps doesn't appear on the watch, I don't understand how to sync the phone and the watch.
I guess I'm too new and there is something that I haven't understand.
Please someone drive me !
Thank you in advance.
Tell me if I'm wrong.
Android Wear is the only "must have" app to manage the watch ?
No need Smart Connect or LiveWear ?...
Open android wear on phone click on the settings gear and click on resync apps
Hello,
Thank you but That doesn't help...
What app do you use to sync the watch?
-JFK- said:
Tell me if I'm wrong.
Android Wear is the only "must have" app to manage the watch ?
No need Smart Connect or LiveWear ?...
Click to expand...
Click to collapse
Android wear is a "must-have" app. And you need also "Google" search app to make sure android wear runs well. (for "ok google" function certainly.)
Did you try to "forget watch device" in android wear and repair it ?
Maybe a factory reset will help, but it is the last option.
Thank you for your reply.
I have disable the location to save battery and the sync have work...
I don't understand!
But now, all work as it should.
Hi,
I'm an expert on SmartWatch 3 and have met with a programmer from the Google team. You require 2 things to fully install apps on your watch, which take max 60 minutes to sync to your watch 100%
1. The first requirement to make sure apps install 100% is a WiFi router network which your phone is connected to, and your SmartWatch 3 is within range of the
area of the router.
2. Your Smartwatch 3 and your Android phone on charge during about 1 hour. The apps sync fast while the battery is being charged, and sync slower if not plugged in.
Do these two things, and the apps will install over WiFi directly from your phone to the watch through WiFi settings of the router.
I just lived in Philippines for 1 month, bought a new Sony phone there and tried installing my Smartwatch 3 over mobil data connection to the phone without a router and not a single app synced. 1 week later ONE app synced. I came home to my country of Sweden with my router and did the same thing with a reset of the watch, and all apps synced in about 45 minutes.
Hi guys,
i bought the secondhand sony smartwatch 3 today and i have a problem with connection
The phone does'nt detect the watch. when i am running Android Wear app and seek watches, phone doesn't detect my smartwatch.
i trying reset watch. not helped.
Please help.
Did you go through the Android Wear app's pairing process? After a factory reset the watch guides you through the steps on how to pair with your phone. Also check that the watch isn't paired as a regular bluetooth device first (forget the device in bluetooth settings of the phone before trying to setup via android wear)
You definitely need to factory reset the watch in order to begin the correct pairing sequence with your phone, if you haven't already done so.
Sent from my VS985 4G using Tapatalk
Hi,
I just bougth a HeadUnit witn Android 10, I haven't been able to connect my android mobile phone. I believe the manufacturer didn't install any mirrorlink server or I am not able to find it. I keep asking the manufacturer trough Aliexpress, and theu say that they are checking with any kind of help for a week.
Reading on the internet I have found two options that may work:
1. Phonelink app: I use it and it work for the first time. But it cannot be used from the HeadUnit screen and it has not work again...
2. EasyConnection app: It seems a good option, but I found a website with a versión for android 9, and I have not been able to connect with the mobile phone ever.
Can I get the last versión of the EasyConnection Server (for the HeadUnit) and some kind of manual, please? I get that after install that, I download from Play Store the EasyConnection app for my mobile phone and it should work, is that rigth?
I have connected the phone by cable, by bluetooh and by wifi (access point of the car) all al the same time. I have activated the USB debug and the option to force resize on my mobile phone. It worked the first time that way with PhoneLink! But I would like EasyConnection or any other software that can be used from the HeadUnit screen, please.
Thanks in advance for the help!!
Have a happy new year!
I found what I believe is the easyconnection server app for the head unit, but it is in Chinese I don't understand anything after installing it.
The version is 6.6.2-662
Another issue! Is there any way to force the new apps I install to resize on the screen? The Head Unit has two bars, one on the top and another one athe the bottom. And some apps I have installed (Android Auto for example) does not fit and the menu options are under these bars and I lose important parts of the apps... Could you please help me to figure out, how to manage the resize of the apps? Thanks!