Anyone able to get the Engineer Mode to work on either ROM?
I have the two app installed in the system
When I dial *#808# it flashes black then goes back to dialer
*#807# works fine with the automatic calibration but doesnt calibrate the rotation
Related
I have a problem with auto rotation. Somewhere between rooting (S off, eng S-off and super CID) and installing a CyanogenMod 6.1.3 I got a problem with a rotation on my DHD. If i enable auto rotate my phone goes in landscape in every single app (Messages, camera, menu...) and it's not coming back to portrait when I rotate the phone. If I disable it everything is in portrait even camera and gallery.
I have installed a sensor test 1.0 by Qualigon and I can see that in Orientation sensor, when I rotate the phone, only X is changing, Y=0 and Z=0 all the time.
I have tried calibration and nothing happened. It's the same.
Help please
Having the same problem.
Try clearing caches and fixing permissions in Clockwork recovery.
Worked for me...
I didn't see any followup on this reply. I am having what seems to be a similar problem with the auto rotation. When I start an application it will correctly present either in portrait or landscape.
When I start the application in portrait and then switch the phone to landscape, the screen's rotation will correctly switch to landscape - but switching it back to portrait will not change the screen's rotation.
When I start the application in landscape it will remain in landscape regardless of the phone's orientation. The only way to get to portrait is to close the application, and then restart the application when the phone is in portrait mode.
I installed an application to test the sensor. When holding the phone in portrait vertically, the values I am getting are: ~230, ~0, ~1. When holding in landscape vertically, the values I am getting are: ~120, ~33, ~33.
The wrong rotation behavior happens in all applications. I switched two ROMs already (Cognition 1.5.2 and MIUI) and nothing changed. I am pretty sure the problem is SW related because as I wrote the initial presentation is correct (meaning the initial orientation that I will get when starting an application is always correct).
I would appreciate help.
similar prob FK!!!!!
Same problem but all my sensors show pass via *#0*# sensor checks. Tried nordic i9505 I9505XXUFNB9_I9505NEEFNB2_I9505XXUFNB9_HOME.tar 4.4.2, then SIngapore I9505XXUFNBE_I9505OLBFNB3_I9505XXUFNBE_HOME.tar 4.4.2 all the fken same problem. Screen rotation all fine when I flash firmware, root, then flash CWM touch - everything good. Screen rotate works until the first reboot after all of this which might even be a day or 2 later. As soon as reboot phone, screen rotation dies and it is a huge pain in the arse. Sensors continue to say pass via *#0*#. Every few days i have to re-flash firmware, re-root, then re-CWM touch, no need to factory reset just those 3 steps. Has anyone got any solutions for this yet??
:crying::crying::crying::crying:
QUOTE=godfather3;21690718]I didn't see any followup on this reply. I am having what seems to be a similar problem with the auto rotation. When I start an application it will correctly present either in portrait or landscape.
When I start the application in portrait and then switch the phone to landscape, the screen's rotation will correctly switch to landscape - but switching it back to portrait will not change the screen's rotation.
When I start the application in landscape it will remain in landscape regardless of the phone's orientation. The only way to get to portrait is to close the application, and then restart the application when the phone is in portrait mode.
I installed an application to test the sensor. When holding the phone in portrait vertically, the values I am getting are: ~230, ~0, ~1. When holding in landscape vertically, the values I am getting are: ~120, ~33, ~33.
The wrong rotation behavior happens in all applications. I switched two ROMs already (Cognition 1.5.2 and MIUI) and nothing changed. I am pretty sure the problem is SW related because as I wrote the initial presentation is correct (meaning the initial orientation that I will get when starting an application is always correct).
I would appreciate help.[/QUOTE]
Running 7.1.1 on my nexus 5x with google dialer 8.0.148481159.
When in call proximity sensor is not disabling or enabling the screen.
Very annoying to have to hit the power button to activate/deactivate screen so that my face doesn't hit all sorts of buttons while in call!
Downloaded AIDA64 to test if proximity sensor working properly, values change normally when putting hand in front of sensor.
Anyone else have this problem? Is it an issue that google is aware of and is working on?
Hi all,
I'm having a strange issue with my G4 H815, and I hope someone here can help!
The problem is that the phone won't rotate the screen when you rotate the device, and then the touch screen will not work. I must turn the screen off and then on again in order for the touch to work. But it will stop working as soon as I tilt the device (activate the gyroscope to rotate the screen). After some time this will force phone to restart and then it finds hard to boot up again.
I think it's gyroscope because the problem happens when I turn the device on the side for eg. when I open camera everything is OK but if I try to take a landscape photo it will immediately freeze. And I also did the testing procedure (277634#*#) when I test the motion sensor gyroscope values hardly change. Also in Settings>Display>Motion Sensor Calibration I get and error "Cannot Calibrate"
My questions are:
Where is gyroscope located?
Is it part of mb (soldered to the mother board)?
Does the screen digitizer affect gyroscope function? (because the glue on the top of my screen has come loose but I don't see it affecting anything other then proximity sensor).
My phone's proximity sensor is not working. Long story short, I had a guy change the display and after that when I call the display always blacks anyway probably he put something in front of the sensor. Anyway, I can't go to a proper technician because they are in another city far from here. In the oxygen os, if I press the power button, the display comes during call but in custom rom like Pixel Experience, Skydragon, Havoc it doesn't. However, in skydragon rom, I found a option in dialer, Disable Proximity Sensor which is actually life saving for me. But I want to use the Pixel Experience rom. Is there any way to get the Dialer app from Skydragon rom ? Or, any way to disable the Proximity Sensor ? I tried the Xposed app; didnt work though.
Right Dialer and Simple Dialer have the option to disable use of the Proximity Sensor. I was using the Sensors Off QS tile (under Developer Options) option previously automated under Tasker but it was kinda hit/miss. Unfortunately these apps don't support call recording it seems.
Hello!
For some odd reason my Proximity sensor stopped working.
Dialed the code for proximity sensor test and I found that the sensor is working,but when I make a call the screen doesn't turn off.
Also I booted into safe mode and the sensor still doesn't work.
Any suggestions?
Tried a factory reset,and still no luck...
Are you by chance using a 3rd party dialer like truecaller etc?
Lauren G said:
Hello!
For some odd reason my Proximity sensor stopped working.
Dialed the code for proximity sensor test and I found that the sensor is working,but when I make a call the screen doesn't turn off.
Also I booted into safe mode and the sensor still doesn't work.
Any suggestions?
Click to expand...
Click to collapse
I've noticed this started happening since the latest firmware update, my screen kept turning on in the middle of a call, report to Samsung and wait for bug fix
digitaljeff said:
Are you by chance using a 3rd party dialer like truecaller etc?
Click to expand...
Click to collapse
Yes ,I was using true dialer, but after the factory reset I am using the stock dialer app.
Lauren G said:
Yes ,I was using true dialer, but after the factory reset I am using the stock dialer app.
Click to expand...
Click to collapse
Ah bummer...sry missed the post where you mentioned factory reset