HTC Desire 820s Bricked and wont charge or turn on - Desire 820 Q&A, Help & Troubleshooting

This is my first post on xda. Today while I was flashing Stock Firmware on my phone using SP Flash Tools, there was a power cut just after the existing firmware on the device was being formatted. Accidentally the pc went off and flashing was interrupted at the very beginning. and now the phone wont turn on or charge or boot into any mode to help me out to re-flash the stock firmware. I tried almost everything mentioned on former xda posts but no luck. The device gets connected to the pc by making a ringing sound and it shows as unknown device in the device manager in the Universal Bus Controller section and the notification pops up while connecting the device i.e, USB Device Not Recognized. I am kind of new to flashing so i don't know much. Any kind of help would be really appreciated. i really don't know what to do now. The phone is out of warranty.

Related

[Q] One x crashed after OTA Update, Dead?

Hello.
I have HTC ONE X for a long time.
today i suddenly got a notification for update (as far as i remember it was the"heartbleed fix" update).
ive downloaded the update and start the installation.
at the moment i press start the phone turned off and became like a "zombie".
hes not turning on, doesnt show the red led while charging (and also doesnt heat up while charging like it used to).
i tried to connect the phone to my pc but pc doesn't recognize the device, and the phone doen't respond to the connection.
some details on the phone (if you need it): CID_044, the rom was official, official recovery and boot, it was relocked because i did it withot changing anything except the unluck and relock.
i tried to download drivers and re installing them, as well as java.
tried to press power +volume up\down\both.
tried to search for device using adb.
tried to rebbot via fastboot and adb (throught the pc).
all this without any luck.
anyone got anothe suggestions? the phone i completly dead?

Dead Lg G3

So I bought a used G3 knowing about the issue it had; it didn't boot. I thought I could find a workaround to this but the phone doesn't boot, doesn't enter recovery or download mode. All the info I have is that when I take off the battery the pc sees it as an unknown device, while it's connected I press the power button for several seconds and it disconnects from the pc, reconnects after several more seconds of pressing the power button. Screen remains dead. Seller told me he had a perfectly working phone before he tried to root it and it never turned on again. One more indication is that the LED notification only flashed red a few times when I connected it to the wall charger and that was it. No LED working after that. I'm open to any suggestions though I guess I'm here for someone to tell me there's no hope reviving the device. Thanks in advance!
Same proble with mine but i bricked mines when update to lollipop and never turn on again . still waiting to some one help to revive my LG
If I come across any solution I'll post it here. In the meantime I've tried the following method on a freshly formatted laptop and I still get "Unknown Device" in Device Manager..
http://forum.xda-developers.com/showthread.php?t=2785089
same here
same problem, someone told me that if was the board or something like that and that it only can be fixed with a complete replacement of this, also, that it could be fixed with linux using comands to install .APK or .TOT.
linux sometimes sees it as Qualcomm CDMA Technologies MSM QHSUSB_BULK, using a virtual machine of linux ubuntu, windows 8.1 sees it as unknow device
LG dead since 3 months ago.................. i wasnt using the phone at all when this happended so........... :crying:
jc.delgado11 said:
same problem, someone told me that if was the board or something like that and that it only can be fixed with a complete replacement of this, also, that it could be fixed with linux using comands to install .APK or .TOT.
linux sometimes sees it as Qualcomm CDMA Technologies MSM QHSUSB_BULK, using a virtual machine of linux ubuntu, windows 8.1 sees it as unknow device
LG dead since 3 months ago.................. i wasnt using the phone at all when this happended so........... :crying:
Click to expand...
Click to collapse
I tried using a boot usb drive to see if ubuntu saw the device but it didn't. Maybe there's some things needed that I didn't do. The thing I don't understand the most is why do windows see it as an unknown device only with the battery out while if I connect the G3 with the battery on, it doesn't show anything on device manager..
Nubrig said:
So I bought a used G3 knowing about the issue it had; it didn't boot. I thought I could find a workaround to this but the phone doesn't boot, doesn't enter recovery or download mode. All the info I have is that when I take off the battery the pc sees it as an unknown device, while it's connected I press the power button for several seconds and it disconnects from the pc, reconnects after several more seconds of pressing the power button. Screen remains dead. Seller told me he had a perfectly working phone before he tried to root it and it never turned on again. One more indication is that the LED notification only flashed red a few times when I connected it to the wall charger and that was it. No LED working after that. I'm open to any suggestions though I guess I'm here for someone to tell me there's no hope reviving the device. Thanks in advance!
Click to expand...
Click to collapse
Hi there.
Please check these 2 threads out and see if any of it will help you. The one for the G2 can also be used for G3.
Here are the links:
http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091 With this technique you would have to find the software online somewhere but this method does revive dead G3 with these symptoms.
http://forum.xda-developers.com/showthread.php?t=2475045
If I helped somehow, hit the THANKS button.
Good luck!
The thing is I can only get the device to be recognized as an Unknown Device in Device Manager and only with its battery out. If I keep 'volume up' pressed nothing happens, it's only shown after I simply connect the USB cable and it pops up after 10 seconds or so. It's very consistent in the way it behaves..
A small update, sometimes when I pull and put the battery again, I connect the phone to a pc while holding down vol- and the pc makes the connected usb sound while the phone led is blinking red for a couple of minutes, then it stops. That's about all there is concerning the phone giving signs of life..

Soft Bricked LG G Pad II 8.0 (LGV498) Wifi only

So I soft bricked my LG G Pad II 8.0 Tablet... Not the worst thing in the world, except that 1.) There seems to be not much at all on the internet as far as stock ROMs or how to guides on fixing my particular tablet. 2.) My computer does not seem to be recognizing my tablet when trying to use ADB, despite having installed all the drivers etc.
My device is stuck in a BootLoop, it will allow me to try a Hard Reset, which is unsuccessful. But it will not go into recovery mode OR Download mode no matter what sequence of the buttons I push and i've scoured the internet trying different button sequences.
My Tablet will charge when plugged into USB, my comp will also go *ding* when i press the power button with the tablet plugged in as if it is reconginzing it and everything. Also Device Manager seems to have it listed with no Exclamation Point or any sign of trouble... Just when I go to use ADB and i search for the device it says *error no device found*
The Tablet just sits there with the LG Logo screen pissing me off more and more as my attempts fail.
I will say USB debugging was not enabled beforehand *cough cough* my mistake
Will reflashing it work by using the MicroSD card method? If that is the only way i will have to just buy one i guess. It did not come with it and it is a Wifi only tablet, no carrier attached.
And if I try the MicroSD method, will it still work without being able to put the tablet into recovery mode?
I believe I have the correct .IMG file for my stock ROM... I just can't seem to get anywhere with flashing it to the device at this point.......
Please Help!
bbrumley said:
So I soft bricked my LG G Pad II 8.0 Tablet... Not the worst thing in the world, except that 1.) There seems to be not much at all on the internet as far as stock ROMs or how to guides on fixing my particular tablet. 2.) My computer does not seem to be recognizing my tablet when trying to use ADB, despite having installed all the drivers etc.
My device is stuck in a BootLoop, it will allow me to try a Hard Reset, which is unsuccessful. But it will not go into recovery mode OR Download mode no matter what sequence of the buttons I push and i've scoured the internet trying different button sequences.
My Tablet will charge when plugged into USB, my comp will also go *ding* when i press the power button with the tablet plugged in as if it is reconginzing it and everything. Also Device Manager seems to have it listed with no Exclamation Point or any sign of trouble... Just when I go to use ADB and i search for the device it says *error no device found*
The Tablet just sits there with the LG Logo screen pissing me off more and more as my attempts fail.
I will say USB debugging was not enabled beforehand *cough cough* my mistake
Will reflashing it work by using the MicroSD card method? If that is the only way i will have to just buy one i guess. It did not come with it and it is a Wifi only tablet, no carrier attached.
And if I try the MicroSD method, will it still work without being able to put the tablet into recovery mode?
I believe I have the correct .IMG file for my stock ROM... I just can't seem to get anywhere with flashing it to the device at this point.......
Please Help!
Click to expand...
Click to collapse
*UPDATE* So I happened to stumble upon a random piece of information that proved REALLY useful in this situation. Someone put in a forum that Lollipop ONLY is detected when plugged into USB 2.0 ports NOT USB 3.0 ports like I was using. So I did this and was able to make my tablet enter into Download Mode FINALLY.... Anyone have any good methods on how to Flash Stock ROM using ADB and a connected soft bricked tablet?
I have already tried a couple methods that I have found and they were unsuccessful. One was using ODIN software and the other was using LG Flash Tool, unfortunately neither worked....

Zenfone 2 does not turn on

Good morning, I have a big problem in my Zenfone 2 and would very much like your help.
Yesterday in the morning he hung up, I thought I had downloaded but I tried to turn it when he called saw the battery was at 50%, I found strange but ok, then the screen locked and the phone started to vibrate and I had to off it. When I called, the battery was at 50%, was saying that the phone was connected and there do not leave sound and saying he was carrying. I thought it might be the rom and turned it on PC to back up and exchange of rom, only the USB no longer recognized the connection to the PC. Was saying that tava carrying, I took the USB and stopped "load" when I called he carried again, just not giving connection to the PC. Anyway I did not back up and changed the rom, he continued the same thing (I was in the AICP (LP) and put the RussiaNBear (LP)).
So I was following a tutorial that I had used before to repair another error (I could not post the tutorial link here, but it's on youtube: (Tutorial - Zenfone 2 unbrick / Restore (ZE551ML / ZE550ML) - In the Droid Will channel)), but I gave soft to do so because the part of the AFT (Asus Flash Tools) it does not recognize the phone, having to disconnect the usb and connect again, and then I screwed me, 'cause the uSB connection was not working. After a few unsuccessful attempts, it seems I agravei even more the situation because now I turn the USB cable pressing volume down and it goes in "Moorefield" and the PC identifies a good, open the xFSTK and can pass the DNX, but when you finish spending DNX the phone should reboot and a screen appears with the symbol of a uSB connection, but that's not what happens. I spend the DNX, the phone restarts and vibrates, there is the xFSTK waiting to pass the OS, but not USB screen appears, the xFSTK does not recognize the phone more in "Moorefield" and I can not do anything else on the device.
I have already connected the phone on another pc, I have changed the cable and nothing. I think it is the mobile usb, if not it would not recognize the first part of xFSTK.
Apologies if I have not posted in the right place, for my English (Google Translate) and the text size, only tried to leave everything well explained so that everyone can understand. Thank you very much, beforehand to help you and I really hope we can solve this problem.
Thank you.
No one ?
no one can help me?

Oneplus 3 just died out of no where

So i was using my phone and decided to restart it after updating my adaway files but my phone never turned back on. The two press the power button screens did not show up either. I tried to uses the MSMdownload tool since i thought my phone was somehow bricked but that didnt work either, it just kept restarting the download process after everything was completed. my computer makes a sound when its connected and it connects correctly as a quallcomm 9008 device but even after all this nothing is working. has anyone experienced something like this or does anyone have any advice?
did you try to long press both power button and vol up ...you should feel a vibration...
maybe it's not turned of maybe it's error causing the screen to be off... also is there any heat?
Which method of the unbrick tool did you use? First or second? If the first, then maybe you should give the second also a try.
Sent from my ONEPLUS A3003 using Tapatalk
I've tried everything and I used th me second method yet nothing happened. I can see my phone get recognized by the computer and get listed on the MSN device list yet nothing happens after it finishes the process. After the green line shows up telling me that it's completed everything the process restarts writhing a few minutes unless I unplug it. No vibration no nothing the phone just died on me after I restarted it .
Try doing MSM on a different PC with all drivers installed , hope it helps
Try to repeat flashing again, there is no other way. Use method 2only. Extract tool again and try flash.
When I was used Xperia Z1, I bricked my phone with a soft brick. So I installed driver in my PC and flash Kernel though FASTBOOT(ADB) either it's not show Device in my PC (I show just "Unknown Device").
After that my phone can connect to my PC again (Now It shown C9303 or something that meant it know it's a phone).
So I can flash by Flashtools again. Soft brick is not scary as Hard brick, you'll find some way to bring it back easily.
Hope this help!
PS. Bricked Phone is WEAK in Battery, always connect it with charger.

Categories

Resources