Develop Bugs

i747 Hard Bricked: QHSUSB - DLOAD : Needing a debrick.img

SGH-I747 (4.1.2 i747's please)/ SGH-i747m( If you have a official 4.3 i747m, please post a debrick.img) only:
Hi, I recently hard bricked my phone into QHSUSB DLOAD and I am going to attempt repairing it through the SD Card boot method.
http://forum.xda-developers.com/editpost.php?do=editpost&p=47431259
I need a debrick.img to flash to the SD card in a Linux OS.
I would have gotten it myself but my phone is obviously dead. I found one before on XDA, but it did not work on my device and it gave me an error in the Linux terminal when it should not have.
-snip-
The end of the 3rd boot-loader stage in mmcblk0 is at 77.3 megabytes. If you are going to help out using your device, try to refrain from uploading an image with a different ROM other than root.
Code:
dd if=/dev/block/mmcblk0 of=/sdcard/backup.img bs=2m count=81054925
The count is the amount of bytes. I am not sure if it is meant to be 1000 bytes=kilobyte or 1024 bytes=kilobyte. The count above is for 1024.
I need someone to install the Galaxy S III unified toolkit, and pull the first 7 partitions from mmcblk0 ,which is where the third bootloader stage ends.(Don't upload a heavily modified device please) http://www.skipsoft.net/?page_id=213 Once you get the files, PM me.
If anyone has a link to a working one, please post that. If you want to get your own image to help me, go ahead.
Thanks guys.

Sorry for the bump... I just need the device running again since the state it's in, it CAN be unbricked.

99ytrewq9111 said:
Sorry for the bump... I just need the device running again since the state it's in, it CAN be unbricked.
Click to expand...
Click to collapse
what happened?

winosxbuntu said:
what happened?
Click to expand...
Click to collapse
I tried to unlock what I thought was a locked bootloader(I could only enter bootloader through ADB)
I found an article that says ezunlock works on all S III's.
It corrupted my bootloader,and my phone gives off no signs of life except "Device QHSUSB-DLOAD not recognized" when plugged in.
This means the motherboard/processor wasn't able to boot from the hard disk, so then it tries the SDcard if it matches the phone close enough.
I need someone to use their rooted i747 to dump the first 77.3 megabytes of "mmcblk0". That contains the firmware and bootloaders. With that, i can burn it to an sdcard in a linux operating system and plug it into my phone.

99ytrewq9111 said:
Sorry for the bump... I just need the device running again since the state it's in, it CAN be unbricked.
Click to expand...
Click to collapse
99ytrewq9111 said:
I tried to unlock what I thought was a locked bootloader(I could only enter bootloader through ADB)
I found an article that says ezunlock works on all S III's.
It corrupted my bootloader,and my phone gives off no signs of life except "Device QHSUSB-DLOAD not recognized" when plugged in.
This means the motherboard/processor wasn't able to boot from the hard disk, so then it tries the SDcard if it matches the phone close enough.
I need someone to use their rooted i747 to dump the first 77.3 megabytes of "mmcblk0". That contains the firmware and bootloaders. With that, i can burn it to an sdcard in a linux operating system and plug it into my phone.
Click to expand...
Click to collapse
find a download link for this http://forum.xda-developers.com/showthread.php?t=1746665 (samsung galaxy s3 toolkit) which can help you fix your phone
if that does not help take it to mobiletechvideos.com and they will fix it for you REASONABLE PRICE
its XDA you will get the help you deserve PLUS i have never encounted that kind of problem HOPE TO GOD IDONT but again am sure an SD-CARD that can write firmware/system IS VALUABLE/USEFULL compared to nothing and that means there is hope left to fix bad code :laugh:

winosxbuntu said:
find a download link for this http://forum.xda-developers.com/showthread.php?t=1746665 (samsung galaxy s3 toolkit) which can help you fix your phone
if that does not help take it to mobiletechvideos.com and they will fix it for you REASONABLE PRICE
its XDA you will get the help you deserve PLUS i have never encounted that kind of problem HOPE TO GOD IDONT but again am sure an SD-CARD that can write firmware/system IS VALUABLE/USEFULL compared to nothing and that means there is hope left to fix bad code :laugh:
Click to expand...
Click to collapse
Thanks for that link! It looks very promising, and I can probably find a stock boot.IMG in there. I will work on tomorrow. If I succeed, I'll edit the OP and make a debrick guide for this drvice forum. A word of advice, try not to mess with your bootloader or you end up like me

winosxbuntu said:
find a download link for this http://forum.xda-developers.com/showthread.php?t=1746665 (samsung galaxy s3 toolkit) which can help you fix your phone
if that does not help take it to mobiletechvideos.com and they will fix it for you REASONABLE PRICE
its XDA you will get the help you deserve PLUS i have never encounted that kind of problem HOPE TO GOD IDONT but again am sure an SD-CARD that can write firmware/system IS VALUABLE/USEFULL compared to nothing and that means there is hope left to fix bad code :laugh:
Click to expand...
Click to collapse
Hi, the toolkit didn't fix my phone, but its defiantly a step up. Since I'm assuming you have the toolkit installed that you suggested it, could you do me a favor?
It will be a bit easier using the toolkit to extract the partition files. If you could pull the first 7 partitions from "mmcblk0" of your device through the toolkit, it will probably set the next step to fix my phone. (Assuming you have a 16g i747... I don't really know)
You don't have to do this of course.
Thanks man.

Bump. Can anyone help out? All I need is the first 7 partitions.
Sent from my GT-I9300 using xda app-developers app

99ytrewq9111 said:
Bump. Can anyone help out? All I need is the first 7 partitions.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
either try using this link http://forum.xda-developers.com/showpost.php?p=27239761 am pretty sure it works for all S3 models, either way on the I747 forum it has been removed, the download link does not work........ so use this
it will work, it may not work but for the time being use this toolkit and also search forums or Google on how to fix this without, i think i found some answers after i had an emmc brick with my S2 but i did not have an SD card to re-write firmware to work again on my phone so i bought the S3 and its awesome

winosxbuntu said:
either try using this link http://forum.xda-developers.com/showpost.php?p=27239761 am pretty sure it works for all S3 models, either way on the I747 forum it has been removed, the download link does not work........ so use this
it will work, it may not work but for the time being use this toolkit and also search forums or Google on how to fix this without, i think i found some answers after i had an emmc brick with my S2 but i did not have an SD card to re-write firmware to work again on my phone so i bought the S3 and its awesome
Click to expand...
Click to collapse
The problem is I need a working phone to pull the partitions. :/ I tried to use the boot image, but it had an error writing while in the linux.

99ytrewq9111 said:
The problem is I need a working phone to pull the partitions. :/ I tried to use the boot image, but it had an error writing while in the linux.
Click to expand...
Click to collapse
This one worked for me http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172

I have a similar problem Hard Bricked after update to 4.3 tried to flash my phone Backup 4.1.2 and died can not log in or recovery nor danlold.Is there any solution.

Bradkirk said:
This one worked for me http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172
Click to expand...
Click to collapse
Did you use an i747 or a i747m device?
If a i747m image works on an i747, it will basically fix all of my problems.

spensa said:
I have a similar problem Hard Bricked after update to 4.3 tried to flash my phone Backup 4.1.2 and died can not log in or recovery nor danlold.Is there any solution.
Click to expand...
Click to collapse
What message appears on your computer when you plug it in?
If it says QHSUSB-DLOAD, you are in faint light.
It stands for Qualcomm High Speed USD Download Mode.
What is means that your processor(qualcomm), is trying to boot, but it cannot find proper drivers for the hardware.
It will then look for something to boot from in the SDcard.
Here is a thread on how some other people were able to do it : http://forum.xda-developers.com/showthread.php?t=2439367

I have an I747M technically. I went for an actual I747M image just in case there was a slight difference. in the thread that one came from though there should be one for the actual att device if you look through it.
and just to confirm, yes the phone was blank and unresponsive. showing up as QHSUSB-DLOAD before i loaded that img onto my external SDcard. and I am using the same phone currently.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app

Bradkirk said:
I have an I747M technically. I went for an actual I747M image just in case there was a slight difference. in the thread that one came from though there should be one for the actual att device if you look through it.
and just to confirm, yes the phone was blank and unresponsive. showing up as QHSUSB-DLOAD before i loaded that img onto my external SDcard. and I am using the same phone currently.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Unfortunately that's the download I found that didn't work.
Thanks for trying though

damn! the only other help I can offer then, is that there is a pretty good thread on this over in the d2tmo section. someone there wrote a little tool to easily download the relevant data. might help you on your quest. or at least make it so you could ask someone that doesnt know ADB. best of luck!
Sent from my SAMSUNG-SGH-I747 using xda app-developers app

99ytrewq9111 said:
What message appears on your computer when you plug it in?
If it says QHSUSB-DLOAD, you are in faint light.
It stands for Qualcomm High Speed USD Download Mode.
What is means that your processor(qualcomm), is trying to boot, but it cannot find proper drivers for the hardware.
It will then look for something to boot from in the SDcard.
Here is a thread on how some other people were able to do it : http://forum.xda-developers.com/showthread.php?t=2439367
Click to expand...
Click to collapse
when connected to the computer written QHSUSB-DLOAD,

spensa said:
when connected to the computer written QHSUSB-DLOAD,
Click to expand...
Click to collapse
OK , take out your battery and tell me your model number(Behind battery). And what phone company do you use?
Did you possibly save a NANDROID on a computer?
( if you have i747m, you can fix your phone, but its hard to do( I havnt done it yet)
Download this image http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172 (thanks to @Bradkirk )
Follow these directions using that image above^^^ http://forum.xda-developers.com/showthread.php?t=2439367
You need to install a Linux operating system (Ubuntu works) to run the commands.
Edit:! According to the T-Mobile thread, you might need a debrick.IMG from a phone on 4.3
Once I know your phones model number, I can edit the main post and ask for you phone model's images.

99ytrewq9111 said:
OK , take out your battery and tell me your model number(Behind battery). And what phone company do you use?
Did you possibly save a NANDROID on a computer?
( if you have i747m, you can fix your phone, but its hard to do( I havnt done it yet)
Download this image http://forum.xda-developers.com/showpost.php?p=46258374&postcount=172 (thanks to @Bradkirk )
Follow these directions using that image above^^^ http://forum.xda-developers.com/showthread.php?t=2439367
You need to install a Linux operating system (Ubuntu works) to run the commands.
Edit:! According to the T-Mobile thread, you might need a debrick.IMG from a phone on 4.3
Once I know your phones model number, I can edit the main post and ask for you phone model's images.
Click to expand...
Click to collapse
I took it to a service to repair

[Q] 4.4.2 debrick.img i747

So i have an i747 galaxy s3 and was running 4.4.2, and i am hard bricked, let me assure you i have tried the 16gb micro sd debrick.img but it still wont work althought i only had a 4.3 debrick.img.So if some one can give me a 4.4.2 debrick.img by doing this
"busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70"
And uploading it i would greatly appreciate it. i am not sure if this method will work and here is why, it was bricked by using a version of ezunlocker for a verizon phone to unlock my att phone's boot loader.If any one can help me out and upload the file that would be great and also if any one has any input regarding the usage of the ezunlocker and the status of my phone and the fix using the 16gb debrick.img method and can give any. again it would be great.

omeadsthename said:
So i have an i747 galaxy s3 and was running 4.4.2, and i am hard bricked, let me assure you i have tried the 16gb micro sd debrick.img but it still wont work althought i only had a 4.3 debrick.img.So if some one can give me a 4.4.2 debrick.img by doing this
"busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70"
And uploading it i would greatly appreciate it. i am not sure if this method will work and here is why, it was bricked by using a version of ezunlocker for a verizon phone to unlock my att phone's boot loader.If any one can help me out and upload the file that would be great and also if any one has any input regarding the usage of the ezunlocker and the status of my phone and the fix using the 16gb debrick.img method and can give any. again it would be great.
Click to expand...
Click to collapse
i looked all over the internet for this. finally the right 4.4~ is found
https://www.androidfilehost.com/?w=files&flid=15759

The i747 bootloader is not locked. I have no idea what that Verizon app would have done, but if that's what bricked it, our debrick method may not work. We also have not been able to restore any 4.4.2 bricks yet. Thats why i posted a new script to create the image, in hopes that doing it a little differently would help.
I wish you luck, but considering how it was bricked, dont get your hopes up too much. Its still worth trying of course, but i have a feeling a jtag service might be the only way.

did same on my first s3 i747. tried to unlock a already unlocked bootloader. before i knew any better, went and got a new s3. (back in my pre-newb days...before i could even claim newbness status.lol), then discovered XDA. started reading and found out about jtag. now that s3 belongs to my brother.
not helpful, i know. just my story.good luck with debrick.img method.
:thumbup:
err on the side of kindness

Anybody know where I can get a debrick image for 4.1.2 (i747) ??
- Guy in desperate need who's been googling for wayy too long now

think theres one here.
http://forum.xda-developers.com/showthread.php?t=2525902
thanks to @DocHoliday77
good luck
err on the side of kindness

mrrocketdog said:
think theres one here.
http://forum.xda-developers.com/showthread.php?t=2525902
thanks to @DocHoliday77
good luck
err on the side of kindness
Click to expand...
Click to collapse
Thank you... Here goes nothing.

let us know how it goes.
err on the side of kindness

mrrocketdog said:
let us know how it goes.
err on the side of kindness
Click to expand...
Click to collapse
Unfortunately it did not work
I was orignally on 4.1.2 and flashed task650's newest AOKP release with CWM but for some reason was bootlooping and could not get past the "Swagger Activated" boot animation. So then I tried to revert back to the stock rom via Odin but I must have tried flashing a 4.3 stock rom because it's bricked pretty good now. Odin does not recognize the phone - device manager displays it as QSHUSB_DLOAD. I've tried making my own jig with no luck. And just recently, I've tried 3 different i747 debrick images using the sd card method (16gb / class 10). Up until just an hour ago, I could take the battery out and plug the phone into my laptop via usb cable and the red light would come on but that doesn't even happen anymore. When I hold down the 3 button combination everynow and then I'll hear Windows "device connect noises" as if it's trying to connect but nothing will happen. I know the correct Samsung drivers are installed on my pc because everything was showing up fine prior to me flashing the AOKP rom.
I'm beginning to think there no more hope for me. Idk if I wan't to bother having my phone shipped out and serviced or JTAG'ed or whatever.

Have you tried different sd cards. Many people find some won't work, while others do.
Sent from my SAMSUNG-SGH-I747 using Tapatalk

omeadsthename said:
So i have an i747 galaxy s3 and was running 4.4.2, and i am hard bricked, let me assure you i have tried the 16gb micro sd debrick.img but it still wont work althought i only had a 4.3 debrick.img.So if some one can give me a 4.4.2 debrick.img by doing this
"busybox dd if=/dev/block/mmcblk0 of=/sdcard/backup.bin bs=1M count=70"
And uploading it i would greatly appreciate it. i am not sure if this method will work and here is why, it was bricked by using a version of ezunlocker for a verizon phone to unlock my att phone's boot loader.If any one can help me out and upload the file that would be great and also if any one has any input regarding the usage of the ezunlocker and the status of my phone and the fix using the 16gb debrick.img method and can give any. again it would be great.
Click to expand...
Click to collapse
Try this Its a debrick image from a 4.4.2 SGH-1747 >>> filedropper.com/debrick <<<

Ehaeli said:
Try this Its a debrick image from a 4.4.2 SGH-1747 >>> filedropper.com/debrick <<<
Click to expand...
Click to collapse
do you have the actual link for that file?

think it might be in this thread..
http://forum.xda-developers.com/showthread.php?t=2820019
REMEMBER please....backup and read read read.
good luck:thumbup:
err on the side of kindness

Looking for a debrick image
Hello, I am looking for someone who can upload a debrick image for I747mvlufnh2 4.4.2 for the 16gb I have searched everywhere without any luck.

Gal tales said:
Hello, I am looking for someone who can upload a debrick image for I747mvlufnh2 4.4.2 for the 16gb I have searched everywhere without any luck.
Click to expand...
Click to collapse
ht#tp://d-h.st/w7g This is the one that worked for me on my sgh-i747M 4.4.2 with koodo . . ive got my phone to turn back on and now im working on getting it to turn on without the sdcard boot
i hope i linked it properly . im too new to post outside links so just remove the # when you copy and paste in the url

I need some for i747 only please !!!!

mitch0422 said:
ht#tp://d-h.st/w7g This is the one that worked for me on my sgh-i747M 4.4.2 with koodo . . ive got my phone to turn back on and now im working on getting it to turn on without the sdcard boot
i hope i linked it properly . im too new to post outside links so just remove the # when you copy and paste in the url
Click to expand...
Click to collapse
Im from mexico. And hard bricked my s3 i flashed a canadian nk2 kk. But when i turn it off never came on againg. So please help me. Im new to all this. I need examples with potatoes. Lol. What else do i need besides this image..
Enviado desde mi GT-I9505 mediante Tapatalk

bighleo114312 said:
Im from mexico. And hard bricked my s3 i flashed a canadian nk2 kk. But when i turn it off never came on againg. So please help me. Im new to all this. I need examples with potatoes. Lol. What else do i need besides this image..
Enviado desde mi GT-I9505 mediante Tapatalk
Click to expand...
Click to collapse
you can try here .....
http://forum.xda-developers.com/showthread.php?t=2549068
i see you found it. nevermind.
"all i can really do , is stay out of my own way and let the will of heaven be done"

mitch0422 said:
ht#tp://d-h.st/w7g This is the one that worked for me on my sgh-i747M 4.4.2 with koodo . . ive got my phone to turn back on and now im working on getting it to turn on without the sdcard boot
i hope i linked it properly . im too new to post outside links so just remove the # when you copy and paste in the url
Click to expand...
Click to collapse
Mitch0422 i have downloaded the 4.4.2 image but i cant turn on my s3. Do i just need to write it to sd and turn on s3?
Enviado desde mi SCH-I535 mediante Tapatalk

Yes
bighleo114312 said:
Mitch0422 i have downloaded the 4.4.2 image but i cant turn on my s3. Do i just need to write it to sd and turn on s3?
Enviado desde mi SCH-I535 mediante Tapatalk
Click to expand...
Click to collapse
Sorry for the long wait for reply . i don't often check my email. To answer you question . Yes you have to write it to the microsd as a bootable image then insert the microsd and boot the phone . it might take awhile of holding down the power button before it shows signs of life. You might also have to take the battery out and try a few times . Once you have it booted back up use Odin to flash the stock rom back onto your phone then take out the sd card and try to turn it on. Follow these directions youtube.com/watch?v=8MnikrpUKZw

[IMG] 4.3 Debrick image

THIS IMAGE WILL ONLY WORK IF YOU BRICKED AFTER UPGRADING TO 4.3 MK3. IT WILL NOT WORK IF YOU WERE ON 4.1.2 JELLYBEAN OR ANYTHING ELSE.
4.3 ONLY
People are looking for this everywhere so I thought a new thread was necessary.
Huge thanks to @thenexusgeneration for dumping this from his new device!!
Enjoy!
I'll be uploading this to my site soon and other mirrors will be available as it is the only currently working image
https://mega.co.nz/#!4s1SQTAA!fVWpGc8Ww-DWv-0VA797V_Bd7MEBOt6EevFuglUNPrQ

so how do people go about using this, backup/restore via recovery menu? asking cause I'm sure you're going to be asked by people who bricked their phones and searching the net for a fix

People who find this will know what to do with it. But no, you don't restore because this fix will unbrick a completely DEAD device. One that won't even power on
Guide is here: http://forum.xda-developers.com/showthread.php?t=2369125

unbrick a completely DEAD
CNexus said:
People who find this will know what to do with it. But no, you don't restore because this fix will unbrick a completely DEAD device. One that won't even power on
Guide is here: http://forum.xda-developers.com/showthread.php?t=2369125
Click to expand...
Click to collapse
if you hard brick on 4.3 you can unbrick now with this new (backup.bin) i have unbrick (2 sprint GS3) ....now the 16gb SD CARD did not work for me i use a (64GB) to get it to work ...i hope it work for you guys to...and yes ...
thanks to thenexusgeneration ....and CNexus..for the backup.bin :good::good::good::good::good::laugh::laugh::laugh:

paco_1 said:
if you hard brick on 4.3 you can unbrick now with this new (backup.bin) i have unbrick (2 sprint GS3) ....now the 16gb SD CARD did not work for me i use a (64GB) to get it to work ...i hope it work for you guys to...and yes ...
thanks to thenexusgeneration ....and CNexus..for the backup.bin :good::good::good::good::good::laugh::laugh::laugh:
Click to expand...
Click to collapse
Over on the DeBrick thread, none of the images (4.3 or otherwise) would work for me, and others with 32gb 4.3 phones. I jtag repaired mine, and made this 32gb image. I re-broke the bootloader on the phone to test it and it works. It requires a 32gb sdcard, I used an off brand class 2 to test with, and it worked the very first time.
So anyone with a 4.3 32gb, try this debrick image:
32gb_43_knox_debrick.img.7z - 26.91 MB (128 MB decompressed)
if you haven't had any luck with anything else.

nvan7891 said:
Over on the DeBrick thread, none of the images (4.3 or otherwise) would work for me, and others with 32gb 4.3 phones. I jtag repaired mine, and made this 32gb image. I re-broke the bootloader on the phone to test it and it works. It requires a 32gb sdcard, I used an off brand class 2 to test with, and it worked the very first time.
So anyone with a 4.3 32gb, try this debrick image:
32gb_43_knox_debrick.img.7z - 26.91 MB (128 MB decompressed)
if you haven't had any luck with anything else.
Click to expand...
Click to collapse
Debrick images are independent of the internal storage size.

CNexus said:
Debrick images are independent of the internal storage size.
Click to expand...
Click to collapse
I would think it wouldn't matter but it does. I have gone over every sites to try to unbrick my phone but none have worked except this. Even with the following method it wouldn't work with 16GB sdcard. Only with 32GB worked for me. Just a little background on my phone setup:
Sprint GS3 16GB 4.3 VPUCMK3
Rooted with CF Rooting method
Bricked by loading NeatROM v3.6 for I9300

pfroz said:
I would think it wouldn't matter but it does. I have gone over every sites to try to unbrick my phone but none have worked except this. Even with the following method it wouldn't work with 16GB sdcard. Only with 32GB worked for me. Just a little background on my phone setup:
Sprint GS3 16GB 4.3 VPUCMK3
Rooted with CF Rooting method
Bricked by loading NeatROM v3.6 for I9300
Click to expand...
Click to collapse
That wasn't what I was referring to, I was referring to the phones storage size not the sdcard's size.

CNexus said:
That wasn't what I was referring to, I was referring to the phones storage size not the sdcard's size.
Click to expand...
Click to collapse
My bad, guess I've been going over the various method that require sdcard to be the same as the phone storage size and had no luck with it.

That you so much for this. Worked perfectly on my friends Bricked S III.

This does work. I have just gotten to download mode after coming from hardbrick QCMUSB_DLOAD mode. You MUST use something > 32g SDHC. I Used 64g SDXC, still worked. I'm back up and running.
Excellent! truly Excellent. XDA community is GREAT!

i need some help. i downloaded something on my sprint s3 that apparently I should not have and immediately hardbricked. Want even turn on no response to buttons etc. What can I do?? I used it for so much other than my phone. Please help

It is best to read the entire thread before posting, to make sure your question has not already been answered. Some users get annoyed when explaining something when the answer is 3 posts above. Unless your S3 is not 4.3 your solution is in the OP. If you cannot download the file, tell them the link is broken.

[Q&A] [HOWTO] UnBrick T-Mobile S III QHSUSB_DLOAD w/Video Walkthrough

Q&A for [HOWTO] UnBrick T-Mobile S III QHSUSB_DLOAD w/Video Walkthrough
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer. Thanks for understanding and for helping to keep XDA neat and tidy! :smile:

Hard bricked samsung s duos GT-S7562
I have hardbricked my s duos and need a debric image. please send me a debric image for my s duos...
my mail id: [email protected] in advance

This is the S3 (T999) forum. You need to ask in your devices forum.
Sent from my SAMSUNG-SGH-I747 using Tapatalk

debrick.img
Hello I am trying to get the debrick. img for the sgh-t999l when I click on the link you have here it keeps taking me to a copy website and I am not able to find this link please help could you possibly send it to me? thanks

Works perfectly fine here. Are you clicking the download arrow and then "download to computer"?
Sent from my SAMSUNG-SGH-I747 using Tapatalk

It worked !!
Thank you so much.
I bricked my cousin's SIII (T-Mobile) yesterday and tried this method.
It worked
Thanks again.

Baffled
I hard bricked a friends SGH-T999V. I had successfully installed CWM and may have flashed it with an incorrect bootloader that I came across on the forums.
I have tried all debrick images on the thread using both the linux and the windows method. I verified and the 23 partitions get created. Tried it a few times with each image on the thread but have had no luck getting the phone to boot. I am currently using a 32gb - Class 10 sdcard.
Been at it for 14+ hours (spread out over 2 days). The S3 was running stock 4.4.2 prior to getting hard bricked.
I appreciated any help with this.

Really depends on what was on the device before flashing. But not all sd cards will work. Try using different ones.
Sent from my SAMSUNG-SGH-I747 using Tapatalk

DocHoliday77 said:
Really depends on what was on the device before flashing. But not all sd cards will work. Try using different ones.
Sent from my SAMSUNG-SGH-I747 using Tapatalk
Click to expand...
Click to collapse
Thanks. I will try another SD card.
Prior to the flashing, the phone was running stock 4.4.2 and all I had done in addition was install CWM d2tmo.

You will need a 4.4.2 debrick.img then. I've got one here: https://www.androidfilehost.com/?fid=95747613655049000
Do you remember which build the firmware you were running was? This image is NF1. If you had something different or newer, it will not work. If you had updated to NH2 for example, you will have to have an image from a device running NH2. Nothing else would work.
I don't believe there is an NH2 debrick.img though. We'd have to find someone willing to make it. (Easier said than done lately.)
Anyway, if you were running the NF1 build, the image above should work just fine.
Sent from my SAMSUNG-SGH-I747 using Tapatalk

DocHoliday77 said:
You will need a 4.4.2 debrick.img then. I've got one here:
Click to expand...
Click to collapse
Doc, This did the trick. It worked perfectly.
Was able to get it booted and flashed the official firmware from your odin thread.
You're awesome

Sent from my LG Mobile using XDA Free mobile app
Doc,
I bricked my SGH-T999N with a ROM for the T999L. I had Android 4.1.2 prior.Can you send me the debricker?

After I put the image on the MicroSD and insert it into my phone it doesn't boot. I am using a Class 4 16 GB microsd card. T-999 Tmobile USA. Any help?

4.4.2 NF1 Debrick
I've managed to Hard Brick my phone and am in a similar position as balcony was. I'm using a Wind GS3 SGH-T999V and used Mobile Odin Pro to flash the Wind variant of 4.4.2 (T999VVLUFNF1_T999VYVLFNF1_GLW) Stock on my phone to be able to fix a CM11 GPS issue. I opted out of flashing the stock recovery -- is that why it happened?
Anyway, it booted fine the first time out of Mobile Odin but once I restarted, it Hard Bricked -- QHSUSB_DLOAD and all. I've tried using all the SGH-T999V debrick images in the original thread including the one that worked for balcony above, confirming 23 partitions, but I'm still having no luck. I have 2 different SD cards I'm trying them on, a 16GB Class 10 and a 32GB Class 10 and both aren't allowing the phone to boot.
Any more insight to this issue? I can provide as much additional information as required.

Debrick T-Mobile SIII attempt
Hello,
Firstly let me say this forum seems to be one of the best sources of information based on my search to resolve my bricked SIII.
I'm afraid the methods and jargon used are unfamiliar to me so I attempted to follow your instructions as best I can.
ISSUE: Phone "bricked" I think I remember seeing the phone trying to update something just before it suddenly shut down.
I'm just looking to recover files off the phone as this is a work phone and ironically I get an upgrade in a weeks time.
Model: SGH -T999 16 gb ( T-Mobile)
Attempt:
I followed the instructions using windows.
Downloaded win32diskimager
Downloaded 4.3 debrick image ( also tried not 4.3 image)
Copied debrick image on to SD card using win32diskimager( SD card FAT32, 16gb and Class 10)
Plugged SD card into my phone, inserted power and battery.
Felt the phone vibrate and got all excited.
However, went into Boot recovery Mode.
Shows:
BOOT RECOVERY MODE:
CHECK BOOT PARTITIONS.
COPY FROM T-FLASH
BOOT RECOVERY..
WRITE 159488 sectors..
FLASH WRITE FAILURE
ODIN MODE
Product Name: SGH-T999
Custom Binary Download: No
Current Binary : Samsung Official
System Status: None
Qualcomm secure boot: ENABLE
Warranty Bit: 0
BOOTLOADER AP SW REV: 1
I did try the above with the not 4.3 image but this didn't do anything.
Have I misunderstood something and done anything wrong?
Any advise from here would be greatly appreciated.

Does it work on core i8262 ??

hhheeeellllpppp
please guys can make debrick image for nokia x i really need it for my nokia x or can any one tell how to do it .
any respond will be apprecieted.

any help wit this this cant flash with odin after using debirck?
any help wit this this cant flash with odin after using debirck?

I need some help please
Can you guys help me please? My Samsung galaxy s dous does not boot into recovery or download modes or into any where , only the Samsung logo , and I really need your help , I think I can bring a dump file from another s dous like mine , could please make me a debrick image ?? And if this way fails , can I use a jtag box ?
Thanks in advance

Sandisk® Ultra SDHC or Micro SD 16 GB Memory will this work or does it have to be a class 10

i9195 qhsusb_dload

sry for my bad english
Hello guys, i have a problem with my little sisters s4 mini lte. This morning my sister wanted to play with her phone but it doesn't turned on or charged. I don't know what to do because my mum worked for this phone hard. When i plug it in my PC (win10) it only shows in device manager qhsusb_dload. I google it and I found out that it is hard bricked. The phone has cm13 because kitkat had performance problems and multitasking problems. Could someone please give me the debrick.img for cm13 for i9195. I know there are guides on other threads how i can do it myself but i really have no idea how to do this . I just know that i have to write the debrick.img on a 16gb sd card and put it inside. I would be very thankfull if someone could help me. :fingers-crossed: @ValenteL pls help me

noobi9195 said:
sry for my bad english
Could someone please give me the debrick.img for cm13 for i9195.
Click to expand...
Click to collapse
There is no such thing as CM debrick.img as custom ROM's do not change the bootloader, you need the debrick image that matches your last stock image installed (probably) as this would have the installed the bootloader which is what your debrick.img takes over from to try to boot your phone. (that is my understanding ...... but I'm no expert in this area!)
But you should try all other methods to boot your phone before this.

That is weird, my girlfriend has the exact same thing 2 days ago with CM13. Also looking for a way to fix this.