Hey guys...so i got an error message for...System.img to large failed.
stupidly rebooted watch...now bricked. stuck at Huawei logo without animation...adb devices, blank.
i'm assuming this thing needs to be sent in?
NEVERMIND!
Step 1: Put the Watch to Fastboot Mode
1) Hold down the power button
2) The screen will go black for about 2 seconds and then boot into the Huawei logo. Keep holding down the power button.
3) Wait for the first vibration, release the power button and then immediately give the power button one short press.
crap...adb devices doesn't detect!
got it...did
flash-all.bat
waited for it to show waiting for devices...then reboot by hand into bootloader as shown in first post. YAY!
Related
Hi all,
I'm really stuck, cannot find a decent tip on the web anymore and need help!
Problem:
Onda v712 tablet is not starting anymore. I can press the "on" button and the only thing that happens is a backlight that turns on.
History:
1. I ordered the onda tab from a webstore in china and it worked great
.... only the market was not working and I could not get rid of the chinese apps that were pre-installed!
2. So I needed to get the superuser rights and install a new ROM. I followed a guide on the web that was for my device:
**New** Root and Full Working Play Store and Google Apps/Root-Explorer Google it and you wil find it (I cannot post a link)
3. In the recovery mode I started the upgrade and it started to run, first ok, then a error about the patch.zip the device rebooted and ended up
stuck in the start splash screen. On my tab it follows after the white android robot image. I waited a while but nothing happened. Everytime I
booted I ended up at the same screen.
4. Usb was not connected anymore and I didn't know any other way to get into recovery other then (adb reboot recovery command from my
laptop)
5. Found a tip on the www that described a button combination for the recovery mode. I pushed the home button and the reset button for 10
seconds. It rebooted and "something" happened because from this moment on no white android robot was shown anymore. I got stuck with
only a backlight or very expensive bad working mirror!!
Everything that I can try from here is very welcome. :good:
Sub questions:
I like to find out how to get into recovery mode again. (what button combination is it)
I also like to know when a tablet/phone is really bricked and how you know it for sure.
I managed to get out of my deadlock!
Somewhere on the web i found this tip about how i could get into recovery:
Next I held down the HOME button while pressing the Reset button for 8-10 seconds.
Keeping the HOME Button down, I them pressed the Power button and held it until I saw the White Android.
Releasing only the Power button I held the HOME button for 4-5 Seconds longer.
The White Android changed to a Big Green Android with some rotating shape in front of his chest.
From there i upgraded succesfully to 4.1.1 and firmware v2.0
Hi,
how are u all i hope you are fine.
to start with i have root the phone by the application stump , and flash a twrp by flashiy.
the phone report and the recovery was working fine i have done the advance wipe and repot the phone.
Now its jammed on the booting with lg logo , nothing is working no download mode and no recovery .
the phone even is it loading up to do it with fast boot. i have tried everything i press all the button a Korean screen will shows tried the options repot and stuck again.
nasser789 said:
Hi,
how are u all i hope you are fine.
to start with i have root the phone by the application stump , and flash a twrp by flashiy.
the phone report and the recovery was working fine i have done the advance wipe and repot the phone.
Now its jammed on the booting with lg logo , nothing is working no download mode and no recovery .
the phone even is it loading up to do it with fast boot. i have tried everything i press all the button a Korean screen will shows tried the options repot and stuck again.
Click to expand...
Click to collapse
Shut the phone down. then remove the battery and wait 20 seconds and reinsert it. Then try to get into recovery (look here for how to http://www.android.gs/enter-recovery-mode-lg-g3/) mode and see if the phone is recognised by the computer if you connect it. Then do a data factory reset in recovery.
Turn off your phone – you can press power button once for selecting “power off” or you can press and hold the power key for about 5 or 6 seconds.
Now, press and hold Power and Volume down buttons at the same time.
When the LG logo appears, release the keys.
Immediately press Power and Volume Down buttons again until the Hard Reset menu will be displayed.
Press Power button once and confirm the hard reset operation (this will not be necessarily if your LG G3 is running on a custom recovery image).
That’s it; now your LG G3 will boot into recovery mode.
gee2012 said:
Shut the phone down. then remove the battery and wait 20 seconds and reinsert it. Then try to get into recovery (look here for how to [ mode and see if the phone is recognised by the computer if you connect it. Then do a data factory reset in recovery.
Turn off your phone – you can press power button once for selecting “power off” or you can press and hold the power key for about 5 or 6 seconds.
Now, press and hold Power and Volume down buttons at the same time.
When the LG logo appears, release the keys.
Immediately press Power and Volume Down buttons again until the Hard Reset menu will be displayed.
Press Power button once and confirm the hard reset operation (this will not be necessarily if your LG G3 is running on a custom recovery image).
That’s it; now your LG G3 will boot into recovery mode.
Click to expand...
Click to collapse
thank you very much for your response.
i tried it same problem stuck in booting the phone lg logo. i tried to put in the download mode the phone stuck on lg logo.
the only response from the phone is when i press the whole buttons and it take me to a koren menu showing imei.
Hello
I was updating from a M version to another M verions. But I had to use the temporary recovery method.
This is what I was doing but didn't finish properly
Requirements:
1. Unlocked bootloader
2. TWRP for Z00A (Download | How to Install TWRP)
Unlock Bootloader on Android 6.0 Marshmallow ZenFone 2 ZE551ML/ZE550ML
Download tool (Download Here)
1. Extract it and connect Zenfone 2 with laptop/pc
2. Click unlock.bat will automatically detect whether the adb or fastboot mode, and then reboot into bootloader
3. Will appear on the screen to unlock the success of mobile phones after five seconds will reboot, then hold volume up the phone automatically re-boot back to bootloader.
4. If you missed the previous step, press the power button for 10 seconds off, then press the "Volume Up" and hold the power button to boot into bootloader.
5. After the phone has successfully re-enter the bootloader, click restore.bat on the computer, where the restore refers to the restore Android ifwi 6.0 otherwise Android phone can not enter the system.
6. The phone will reboot and restore white on black ASUS logo screen, and then enter the Android system.
Click to expand...
Click to collapse
I extracted and connect my zen2
Ran the unlock.bat
The phone entered the bootloader, flash his things and boot again but on the white screen
Then I had to hold power button 10s to turn it off and turn it on again
Entered the bootloadr by holding Power+Vol UP then to recovery.
At this time I just used the recovery as I usualy do, Wipe everything, cache, data, etc.
Connect to the PC, put the new UL-Z00A-WW-4.21.40.184-user.zip there and flash.
BUT now that comes the problem. I select the option to boot it after finish flashing.
So obviously I didnt finish the steps mentioned on the quote above.
I didnt ran the restore.bat before reboot into system and now All I see is black screen.
I've tryed some steps of those tutorials for briked phones but My computer can't see the device for long enough
http://forum.xda-developers.com/zenfone2/help/thead-bricked-phone-updating-to-mm-tips-t3452785
I try to do those steps but I'm stuck on this part
now back to the Zenfone 2, hold power for 20 seconds to shutdown, then press simultaneously the key "power" + "volume down", until phone vibrates. Or computer makes detection sound, wait a few seconds it will add an item immediately below intelSoC in device manager “MOOREFIELD” new devices is successful.
Click to expand...
Click to collapse
My phone doesn't boot even on bootloader. It just vibrate twice and then nothing happens.
On my device manager I can see the "Moorefield" but only for a brief moment. when I try to turn on the phone then it immediately disapears and repeat this process (Vibrate twice, long preiod doing nothing and still black screen, then vibrates again twice, repeat)
Any suggestion?
Thanks in advice
Seikushim said:
Hello
I was updating from a M version to another M verions. But I had to use the temporary recovery method.
This is what I was doing but didn't finish properly
I extracted and connect my zen2
Ran the unlock.bat
The phone entered the bootloader, flash his things and boot again but on the white screen
Then I had to hold power button 10s to turn it off and turn it on again
Entered the bootloadr by holding Power+Vol UP then to recovery.
At this time I just used the recovery as I usualy do, Wipe everything, cache, data, etc.
Connect to the PC, put the new UL-Z00A-WW-4.21.40.184-user.zip there and flash.
BUT now that comes the problem. I select the option to boot it after finish flashing.
So obviously I didnt finish the steps mentioned on the quote above.
I didnt ran the restore.bat before reboot into system and now All I see is black screen.
I've tryed some steps of those tutorials for briked phones but My computer can't see the device for long enough
http://forum.xda-developers.com/zenfone2/help/thead-bricked-phone-updating-to-mm-tips-t3452785
I try to do those steps but I'm stuck on this part
My phone doesn't boot even on bootloader. It just vibrate twice and then nothing happens.
On my device manager I can see the "Moorefield" but only for a brief moment. when I try to turn on the phone then it immediately disapears and repeat this process (Vibrate twice, long preiod doing nothing and still black screen, then vibrates again twice, repeat)
Any suggestion?
Thanks in advice
Click to expand...
Click to collapse
you must post question in the thread you are trying instead of making new one. any ways. long press power button to shut down the device completely. then press power button and volume down button. as phone vibrates release power button but keep holding volume down button and wait till moorefield appears in device manager. now release the volume button then click begin download in xfstk.
if u have further question post in in above thread you are following to unbrick
sukhwant717 said:
you must post question in the thread you are trying instead of making new one. any ways. long press power button to shut down the device completely. then press power button and volume down button. as phone vibrates release power button but keep holding volume down button and wait till moorefield appears in device manager. now release the volume button then click begin download in xfstk.
if u have further question post in in above thread you are following to unbrick
Click to expand...
Click to collapse
I did it already and only shows up for a brief moment like I said and then disappears a second before the phone vibrate
help please D:
Seikushim said:
help please D:
Click to expand...
Click to collapse
any luck fixing? i got the same result, no screen or anything, two vibrations since yesterday
Sadly, no.
no fix for me yet...
Let me know if you find something
You have tô unbrick your phone. There are some tutorials in the forum
I am using the Z008D variant of the Zenfone 2.
I had bricked my phone 3 times and the guides that had helped me are:
https://forum.xda-developers.com/zenfone2/help/thead-bricked-phone-updating-to-mm-tips-t3452785
https://forum.xda-developers.com/zenfone2/general/guide-brick-soft-hard-bricked-zenfone-2-t3284256
I too had the same problem the first time I unbricked my phone. The moorefield device would show up briefly in device manager. It is stated in the guide that you had to press power+vol down when connecting the phone to use xFSTK. I googled and found that you had to actually press and hold the vol down button only and then connect the USB cable, then release it when the moorefield device is detected.
I have TWRP installed, and have managed to run it a few times. Now I cannot start TWRP at all.
From off, if I switch on, the following happens:
1) Screen with Samsung Galaxy A70 - Secured by Knox
2) 0.5 seconds later another screen, "this phone's bootloader is unlocked and it software integrity. .." and "press power key to continue..."
3) 5 seconds later, same screen as (1)
4) 3 seconds later, red letters "this phone is not running Samsung's official software"
5) 3 seconds later blank screen with "samsung" and then booting to android.
In my experience I have to flash twrp every time I want to use it( I don't know the reason but I couldn't fix it ) , for booting twrp on the other hand I turn off the phone first, then I press power button+volume down until the "this phones bootloader..." screen appears, here is the tricky part, you have to quickly let go of these two buttons, press power button, let go of the power button (after the warning disappeared) and then press volume down button (and hold it) until twrp logo appears, this happens really fast so you may need to do it a few times to get used to it.
mobin22 said:
In my experience I have to flash twrp every time I want to use it( I don't know the reason but I couldn't fix it )
Click to expand...
Click to collapse
Yes, same here, the only time I have managed to run TWRP on this phone, is right after a flash.
mobin22 said:
and then press power down button
Click to expand...
Click to collapse
Do you mean volume down?
Zilliman said:
Yes, same here, the only time I have managed to run TWRP on this phone, is right after a flash.
Do you mean volume down?
Click to expand...
Click to collapse
Power off the device, plug into a pc, wait for it to start charge, hold vol up and power till it turns on. Wala boots to twrp. If you have magisk installed,you can use the reboot option within magisk.
mobin22 said:
In my experience I have to flash twrp every time I want to use it( I don't know the reason but I couldn't fix it ) , for booting twrp on the other hand I turn off the phone first, then I press power button+volume down until the "this phones bootloader..." screen appears, here is the tricky part, you have to quickly let go of these two buttons, press power button, let go of the power button (after the warning disappeared) and then press volume down button (and hold it) until twrp logo appears, this happens really fast so you may need to do it a few times to get used to it.
Click to expand...
Click to collapse
Samsung changed how to enter recovery on Android 11. Power off device, plug into pc, wait for it to charge, then hold vol up and power till it turns on. Alternatively, if you have magisk installed, use the reboot options within magisk.
I did that. Thanks!
But it has gone to:
Android Recovery
Samsung /a70qxx/a70q
11/RP1A.200720.012./A705FNXXUB5DVB3
user/release-keys
Use volume up/down and power.
Reboot system now
Reboot to bootloader
Apply update from ADB
Apply update from SD card
Wipe date/factory reset
...
...
...
Where is TWRP? It seems it's gone.
Zilliman said:
I did that. Thanks!
But it has gone to:
Android Recovery
Samsung /a70qxx/a70q
11/RP1A.200720.012./A705FNXXUB5DVB3
user/release-keys
Use volume up/down and power.
Reboot system now
Reboot to bootloader
Apply update from ADB
Apply update from SD card
Wipe date/factory reset
...
...
...
Where is TWRP? It seems it's gone.
Click to expand...
Click to collapse
That's because you're not installing it properly go back to my guide and follow it exactly and stop listening to these other people. I've been modding this device since it first came out with Android 9, I know every inch of this device. You're getting confused by what other people are telling you
MarvinMod said:
5- Press and hold vol down and power till the screen turns blank then immediately press and hold vol up. The device will reboot then land you in the twrp splash screen
Click to expand...
Click to collapse
It fails here, on this step. After successful flash of recovery.tar, power + vol down to reboot, cable still connected, nothing you can do now can bring TWRP up. The phone boots into Android.
EDIT: I think I have now got it. I will update in a few mins.
Zilliman said:
It fails here, on this step. After successful flash of recovery.tar, power + vol down to reboot, cable still connected, nothing you can do now can bring TWRP up. The phone boots into Android.
EDIT: I think I have now got it. I will update in a few mins.
Click to expand...
Click to collapse
After successful flash of recovery.tar, power and vol down to reboot, as soon as the phone screen goes blank, immediately release all keys and press and hold vol up. Must be as soon as screen goes blank. The device will then reboot twice and land you in twrp splash screen. You must hit vol down and power after successful flash then when screen blanks, vol up. If you miss this step, twrp will not hold and revert back to stock recovery.
Here is the notes I made today:
****************************************************************
INSTALL + START TWRP
phone is off
press up + dn
insert cable
go into download (press up)
ODIN 3.14 + AP:tar(vbmeta.img+twrp.img), auto reboot off, press upload
when it succeeds, press dn + pwr until it reboots
then quickly up + pwr until it starts (no need to hold down)
this starts in TWRP
from powered off
press pwr button
goes into twrp or android(system) -- depending on what was used last time
if we used reboot->system last time it will now **Always** go into system!
to go back into twrp:
switch off
power cable until charge
pwr + up until it starts
****************************************************************
The above means that you CANNOT go back to TWRP unless you have a cable and a PC near by.
I have TWRP and LineageOS with Magisk installed on my A50. Normally, when my phone boots, I get the following sequence:
1. Phone vibrates.
2. Samsung Logo appears for a very short time, with bootloader unlocked warning at the bottom.
3. A screen showing a bootloader unlock warning at the top and "PRESS POWER KEY TO CONTINUE" appears.
4. After a while or if you press the power key, an additional unofficial software warning appears in red letters at the bottom.
5. After some time the phone continues to boot normally.
My problem is that after the latest reboot ("reboot into recovery" via power menu), it gets stuck at step 4 and won't continue to boot, neither recovery nor system, even if I wait for tens of minutes.
What I've tried:
-reboot with volume +/-/poweroff
-reboot with volume volume -/poweroff
-all of the following with and without USB connected to PC:
-power/volume +/- at boot, both starting after logo screen as well as starting before logo screen, as well as releasing power at logo screen
-power/volume + at boot, both starting after logo screen as well as starting before logo screen, as well as releasing power at logo screen
-power/volume - at boot, both starting after logo screen as well as starting before logo screen, as well as releasing power at logo screen
-volume + at boot, both starting after logo screen as well as starting before logo screen
-volume - at boot, both starting after logo screen as well as starting before logo screen
-volume +/- at boot, both starting after logo screen as well as starting before logo screen
None of these helped. I just get the normal sequence 1-4 and then stuck every damn time. Can't get into recovery or download mode. Can't even power off, obviously.
Is my phone gone for good?
same **** here. for me i cant charge the battery too. but before that with about the same problems i got it to work again for a few days.
now hangs on step 4
wollert60 said:
same **** here. for me i cant charge the battery too. but before that with about the same problems i got it to work again for a few days.
now hangs on step 4
Click to expand...
Click to collapse
With some help I managed to get into download mode, and from there reflash stock rom with ODIN.
Basically, you need to reboot the phone with power/vol+/vol- and as soon as the screen goes black, you release power but keep pressing the volume buttons, and also immediately connect the USB cable with the PC. Timing is key.
otterwise said:
With some help I managed to get into download mode, and from there reflash stock rom with ODIN.
Basically, you need to reboot the phone with power/vol+/vol- and as soon as the screen goes black, you release power but keep pressing the volume buttons, and also immediately connect the USB cable with the PC. Timing is key.
Click to expand...
Click to collapse
thats rng af. I also accidentally managed to flash another rom over it. it starts and could be set up again. but this is the second time why I had to do the whole thing
otterwise said:
With some help I managed to get into download mode, and from there reflash stock rom with ODIN.
Basically, you need to reboot the phone with power/vol+/vol- and as soon as the screen goes black, you release power but keep pressing the volume buttons, and also immediately connect the USB cable with the PC. Timing is key.
Click to expand...
Click to collapse
bro, you helped me alot, i'm stucked at this screen maybe 2 hours I didnt know what to do.
Btw, I've it just in 1 time =))
I got a way easier Method which has saved me several times
Is something i came up myself
Il be as precise as i can be so everyone understands!
1.Plug the phone to the wall (Your charger to the outlet)
2. Hold Power And Volume - (Volume down) until the phone shows the second charging animation (Which is the one after the first image of the phone charging [A circle with the lightning icon in the middle], this second screen shows a charging animation and the percentage of the battery) This indicates that the phone is fully Turned Off
3. Unplug your phone and the charger off the wall and bring it to your computer
4. Plug your cable to your Computer then back on your phone Hold Volume + and Volume - (Volume up and Volume Down) and plug your phone to your computer WHILE HOLDING BOTH VOLUME BUTTONS.
This little trick will put your phone in download mode so you can restore your device using Odin OR Flash Twrp with Odin and boot to right into Twrp (There is a way to do it without turning the phone on and having to go back to step 1, Follow this Tutorial to do it
(
)
I Hope this helps you all
And Happy Flashing!