hi there i just installed my erisin es2007a to my car there was 2 problems with the unit.
1. the bluetooth will not pair and show any devices
2. 3g will not work but the signal bar is showing a signal
i got in contact with the seller and they advised me to install a update. they sent me a update and i unzipped it and put on a sd card and installed on the my head unit.
after the update the vol , navi , power , screen in and out buttons all stopped working and the update didnt even fix the problem with the bluetooth and 3g problems.
so now my sd car is stuck in the machine.
i think its a software problem but ive been looking at all the ubdates that is on this site and cant work out what one will suit my problems.
mcu version = mtcb-kgl-v2-80
android version =4.4.4_07112015
kernel version = 3.0.36+ [email protected] #1429
cpu = arm [email protected] (x4)
any advice will be greatfull
Related
My O2 IIs just started doing this today, anyone have any ideas?
If I have bluetooth on and press the power button it turns off the bluetooth connection, once I press the power button to turn the unit back on it restarts the bluetooth connection (can see icon change at bottom of screen).
I have hard-reset the device several times. I even hard reset it and stopped it running the Extended ROM apps (just in case this was cause) and it still did it.
Install BT build 3500.
It solves the issue you talked.
I did and it doesn't.
Hmm, I see the same thing... I'm new to these forums - where would one find different BT builds for download?
Which phone do you have?
Also, I found part of the problem was Zenphone v5.1. Off to drop a message about problem to author.
It's a CDMA version, marketted as a "Harrier" by my telco:
http://www.telecom.co.nz/content/0,3900,204416-201908,00.html
Relevant stuff:
Model: PH20A2
ROM Version: 1.29.00 WWE (24/09/04)
Radio Version: HA01_136
Protocol Version: AA3.3.301
Ext ROM Version: 1.29.118 WWE
BT is currently build 2300
I did manage to find a thread here that referenced a webpage with the two BT patches I was after, I'm about to head to work to give them a go... (I only have one windows machine, and it's one of my desktops at work...)
Thread: http://forum.xda-developers.com/viewtopic.php?t=15970
Page: http://www.catherall.name/downloads/
I have the same problem after installing these patches!!!! Anyone able to help? Still disconnecting bluetooth, although the light is still flashing, it seems to get to standby! Can anyone help with this?
Hello everybody,
I am using ARHD since v9.x (don't remember the exact versin number) and moved to JB as soons as it was released.
Since ARHD v17.0, I experience bluetooth heratic connectivity to my car phone system.
My OneX and my car are paired but it takes more and more time to have them connected.
In v17.0 it took about 3-5mn to connect, this morning, with v18.1, it took about 20mn...
I tryed the following :
upgraded the firmware to 1.39
"superwiped" and re-installed ARDH 18.1 rom
cleared the bluetooth entries in both the phone and the car configs
No improvement.
Is there an issue in the BT module since v17.0 ?
Does anybody else experience the same issue ?
Well in two words : "help, please !"
Thanks in advance.
No one else ?
Come on guys, no one else experiences the same issue ?
I'll try to investigate further by myself:
Check the car BT system with anoter phone
Check the phone with a BT connection to a PC (I don't have another BT headset)
Install another custom ROM, e.g. cyanogenmod
Revert back to the original HTC ROM
Well, several tests later... Still facing the same issue.
If i erase the BT profile from the car audio system and the phone, then re-associate them together, the connexion occurs within 30sec !!!
then shut off the car and switch it on again... Both the car and the HOX are trying the connect for several minutes.
I will try to reset the phone when the new version of ARHD (18.2) will be released.
Checked BT connexion between HOX and a PC and another phone
-> connection : ok
-> stop / start : ok
No pb found on HOX side
Checked car with 2 differrent phones (wiko cink slim and lg gt505)
Car does not find any of them...
Even when I stopt any BT connection from the car interface, the BT system retart the phone search...
I'll have to call VW...
So, there is no bluetooth issue in ARHD 17.0 .. 18.1
Unfortunatelly, I have an issue with my car
Topic is closed
Hi,
so I am kinda new to this and wanted to upgrade to 5.1.1 below is the initial information.
Its a Roadmaster AN-111 GMC (if it matters)
It was MTCB - KSP 2.86
upgraded to MTCB KSP 2.89(KSP_11-28-2016_1.99_dmcu.img)
Firmware was 4.4.4_11032016
I installed the KLD - 2.1.1 december update
now the system boots up but does not show any display, if i plug in a USB it starts to play songs. All hardware button BEEP when i click so does the buttons on steering. I
I can go into recovery but I continuously receive the no sd card - cant post a picture yet
any chance of recovery please?
Hello,
Are you sure the MCU upgrade you did was to KSP 2.89 ? The filename you gave says something else: KSP_11-28-2016_1.99_dmcu.img (notice the 1.99 in the filename).
That would mean you did a MCU downgrade. Try flashing the MCU back again (i have KSP mcu too, not sure which version, i may be able to help you).
Regarding 5.1.1 update, i have the same behavior. I do not see the "desktop" with all the icons, but i see toast messages, popups, the "preparing to shutdown" window, so, maybe display driver problem ?
Hi guys,
your help please! I have a Px3 2GB head unit with the following:
- MCU MTCE_KGL_V2.70_1
- Androd 7.1.2
I was trying to update to the latest Malaysk version 5 and somehow during installation an error message appeared and the unit is now unusable. When turned on only the initial screen (Navigation system) is visible and nothing else, so I can only switch it either off, or on and it stays on that screen. I have tried to install a new software through USB and microSD but nothing seems to work.
Do you know how I can install the software again so that I can use the unit?
Many thanks for your help!!
Hello,
I have very big problems with my car radio at the moment.
I bought this car radio.
Code:
amazon.de/gp/product/B07BFS29HZ/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
1st OS: Android-8.0
2. CPU: Rockchip PX5 ,Cortex-A53, Octa-Core
3. RAM: SAMSUNG DDR3 4G
4th Flash: 32GB
5th Radio: NXP 6686S
6. GPS: SIRF III
Seventh screen: Capacitive and multi-touch screen
8. video decoder: 1080P HW
9th WIFI: Built-in
10th DVR: USB camera (PC standard)
I have already successfully used the car radio until the car radio has restarted and is now hanging in a boot loop.
It is no longer possible to start the car radio.
Please see the following video:
Code:
photos.app.goo.gl/cbKFMqfr5HDhDTc87
I then tried to reset the car radio to the factory settings using the reset button, but that didn't work either.
It reboots again and again.
Then I found out how to get into the recovery mode.
I made them a picture with the messages
Code:
photos.app.goo.gl/56SphjLcg2a5bwQb8
Apparently he can't find a file to successfully boot the car radio.
I suspect that if I put a correct kupdate.zip file on an SD card and boot the radio, it could work again.
Unfortunately I don't know enough to find the right file or I don't want to risk a brick of my radio if I use the wrong file.
Can you please help me get the car radio up and running again?
Many thanks
Best regards
mandragora