Hi All,
Installed the latest ResurrectionRemix-M-v5.7.0-20160616-jfltetmo.zip on my S4 and cannot connect to Mercedes Benz navigation. Both system can see each other. No errors get displayed on the phone pairing devices. MB Command always displays an error "Access denied". There no differences if paring initiated from each devices.
Tried factory reset CM13 - same issue.
Tried factory reset and RR 5.7.0 after that - same issue.
Tried BlueDUN - couldn't see even any connection attempt.
Tried to connect to iPhone - iPhone reported an error - "Samsung Galaxy S4 not supported", no errors on S4.
Tried to connect to ASUS Android tablet - all worked, could send a file.
Thanks for suggestions.
Related
I am having a problem with pairing bluetooth headsets on this JB install. already paired devices do not connect, and if I removed them and try to paired them again, It will prompt three times to enter the pin, and only then it connects. but once is disconnected I have to repeat the whole process. Any ideas? I would ask this in the specific thread, but it seems I am not allowed to post.
Stuck at 3rd pairing screen (see image) after numerous factory reset and can't pair with phone, although phone says it is paired but watch won't go beyond this pairing screen! Tried everything (uninstall - clear cache, data, re-install android wear, unpair bluetooth ), but no progress. Any advice? thanks!
Have you found a solution for this issue? Im having the same issue
Just sideloaded the Mashmallow update from 5.1.1 to 6.0 (downloaded from Google) and the update seemed to go normally - most things work as normal. But the WiFi wouldn't turn on, and it's mac address reports as 02:00:00:00:00:00. That address I know was an issue in the M Preview as a fake address.
I didn't want to hard reset it but in the end relented and loaded a clean new version of 6.0 from Google. When it restarts the second thing it wants to do, after selecting a language, is start the WiFi so it can log on. Of course WiFI won't start, and I can't "skip" so it's stuck. I tried Bad_Boyz fromXDA, and then going back to 5.1.1, and now forward again to 6.0 - same result. I suspect the WiFi mac address has been cleared. I found a little help that if I shell into the tablet, and write the mac address into /persist/wifi/.macaddr I might move forward. I know how to do this, but I can't shell in with adb. I can talk over USB, and run fastboot. When I connect via USB the Nexus mounts (sort of - the storage folder isn't shown when the tablet is at the "Select WiFi network" stage of setup)
When I run "adb devices" - I can't see any, even though I can "fastboot reboot recovery" and the like. I'm sure bluetooth (mac address) is broken too, but I"ll fix that later.
Does anyone have any idea how I can encourage adb to talk, so that I can "adb shell"?
Safe Mode
Just so you know - I started it in safe mode, which I have done before, but anyway - and the WiFi works. Also, USB debugging is presumably switched to off on a hard reset, and I couldn't log in to enable it without working WiFi. Suddenly my mac address is back. Don't really know if safe mode is the answer but it's worth trying...
To get into Safe Mode - long press on the "Power Off" question when you turn it off - it reboots in safe mode.
I have posted the same question, but it was not at Lineage OS Questions & Answers, so that is the reason that I make the exactly same thread here on the right section.
I have a Lenovo TAB 4 10 Plus, and it is running on Lineage OS 16(Android 9).
I use it a while but since 5 weeks, if I connect to my home WIFI network, it shows this error message: Connected, no internet
I have done this:
- Forgetting the network
- Resetting connectivity settings
- Resetting the tablet
- Resetting the Router
- Restarting the tablet
- Done research on the internet about this error message
- Watched the videos about it and exactly followed the steps
But these solutions are not effective
How can I solve this problem?
Hi,
Trying run Andorid Auto(5.4.502264-release from gPlay) on Skoda Octavia but no success. Of course I was try run with different device (Lenovo Tab) and it works.
Is it working with:
Note10+ Exynos
Baseband version N975FXXU4CTE9
Steps for reproduce:
Connect over USB
Allow permissions on Phone
Choose Android Auto on car infotainment screen
connecting
Connection lost
on Note10+ I can see Android Auto running in
What I was try
- change usb cable (3 different types)
- in Andorid Auto app on Phone setting I was try delete connected phone
- delete Phone in car infotainment
Any Idea how to solve it? Do you have similar experience?
Thank you
Update:
after testing S10 in the same car and it works again, I was made factory reset of Note10 and it works too.