Hello all. This is my first thread because I'm new to this phone modding.
So here goes.
I have a Samsung Galaxy Note 4 on Vodafone SM-N910F.
Its a lovely phone except I'm bored of it so have decided to flash a new rom.
I used odin to root, then downloaded 'DR KETAN's rom to flash, however it wouldn't boot into recovery.
When it eventually did, and 'DR KETAN' installed, my phone was shoved into a boot loop.
So after a re-flash of the stock rom and a re-root, I now can't boot into recovery again to try again.
Either manually or using an app, to get into to recovery, I get a picture of the little android man, saying android is upgrading (or updating) I can't remember. Then it comes up with a menu which isn't recovery. And I get the message
'DM-VERITY VERIFICATION FAILED'
Please help me.
Someone run me through what I should do, every step if the way because I literally am stuck
(And dumb it down a bit for a Newby please)
Related
I have been using the i747z ROMs for quite some time and after trying a bunch of other ROMs I always reverted back to theirs. So when their 3.0 version came out with Android 4.3 I installed it, using ClockWorkMod recovery. Right after it installed, CWM displayed a message about the boot loader and to fix it. So I went ahead and did that (Don't really remember what the message was) What I know is that I lost root. Also the phone could not connect to the mobile network, only on Wifi. So this morning, I factory reset the phone again, and attempted to root the phone with Odin with CF-Auto-Root-d2att-d2uc-samsungsghi747 (which I had used when I first rooted the phone). Now the phone doesn't boot past the 2nd samsung logo, it starts out with the Samsung logo with the blue circle around it, then the AT&T Rethink Possible and then the plain white Samsung logo. Also, the LED has a slow blue flicker.
I can get the phone into download mode and I have used Odin to attempt to load the stock firmware and the stock bootloader. But after restarting the phone I can't get past the same screen described above.
I am pretty sure this is not related to the i747z v3.0 ROM but rather something a miss with the order in which things need to start in Android. I have done some reading on that but I am not sure what I need to do to correct this soft brick situation. ( I have googled "soft brick" as well)
Any thoughts would be greatly appreciated!
mozphoto said:
I have been using the i747z ROMs for quite some time and after trying a bunch of other ROMs I always reverted back to theirs. So when their 3.0 version came out with Android 4.3 I installed it, using ClockWorkMod recovery. Right after it installed, CWM displayed a message about the boot loader and to fix it. So I went ahead and did that (Don't really remember what the message was) What I know is that I lost root. Also the phone could not connect to the mobile network, only on Wifi. So this morning, I factory reset the phone again, and attempted to root the phone with Odin with CF-Auto-Root-d2att-d2uc-samsungsghi747 (which I had used when I first rooted the phone). Now the phone doesn't boot past the 2nd samsung logo, it starts out with the Samsung logo with the blue circle around it, then the AT&T Rethink Possible and then the plain white Samsung logo. Also, the LED has a slow blue flicker.
I can get the phone into download mode and I have used Odin to attempt to load the stock firmware and the stock bootloader. But after restarting the phone I can't get past the same screen described above.
I am pretty sure this is not related to the i747z v3.0 ROM but rather something a miss with the order in which things need to start in Android. I have done some reading on that but I am not sure what I need to do to correct this soft brick situation. ( I have googled "soft brick" as well)
Any thoughts would be greatly appreciated!
Click to expand...
Click to collapse
After flashing through odin did you format data?If not try it.
Go into recovery and wipe data.
**SOLVED**
Thanks xXFl4sh, I had tried that.
Solved!
Alright where do I start? How about RTFM Some how I had missed the part about flashing a bootloader and a modem after the ROM. Not recalling having to do that before, I skipped right over it. Once the recovery CWM 6.0.3.1 was finally loaded, getting the flashing the ROM, the bootloader and the modem was easy as usual.
The key was having to use Odin to install a recovery in .tar or .tar.md5 format since I could not access a Recovery Mode on the GS3, as well as a rooted stock image (I used root66_ATT_I747UCDLK3.tar.md5 which is a rooted Android 4.1.1 for AT&T) For the recovery, I couldnt' find a .tar or .tar.md5 for ClockWorkMod (did find a utility to convert it, but didn't want to introduce another variable into the mix) so I used one from Team Win Recovery (v2.6.3.0) and with that I loaded the CWM recovery. Once all of that was in place, I proceed to factory reset, clear data, cache, system and then flash the new ROM, bootloader and modem.
In all of this I learned quite a bit about the whole process and how to narrow down possible resolutions. I still see the "Rom may flash stock recovery on boot" message after flashing either a ROM, bootloader or modem, but just backing out without answering Yes or No seems to work. Also (and this may be related, I don't see the option to restart in recovery from shutdown menu). Don't really know what that's all about for now, and honestly don't want to mess around (at least for a while)
I know the steps are general, but I hope this can help some else if they get their devices in a soft brick situation. As for the i747z v3 ROM with 4.3, I really like it, everything works (Wifi,Blutooth,tethering) and the battery seems good as well.
Thanks!
So I have an Att Note 2, which is bricked or soft bricked. I am a very rookie Android guy when it comes to modifying or hacking. I did root my Note 2 with Cyanogenmod. However, I missed S Note and the use of my S Pen so I researched a bit to get back to stock with the use of Odin and stock roms found on the net. I was successful, and actually amazed it worked. Long story short, a few days after that, an OTA update hit my phone, didn't even think about it and began the download. The phone downloaded the update, and rebooted to complete the install. The problem is, during reboot, the phone got stuck on the "Samsung Galaxy Note II" screen. I researched a bit online, and everyone said get to recovery mode and do a few things. Problem is, I can't get into recovery mode, I can only get the screen described above, and the download screen, THAT IS ALL. Looked a bit more online and attempted to flash various stock roms with Odin. Some were successful, Odin passed, and the phone would get stuck on the Note II screen again, and would not boot into recovery mode, same issue with only being able to access download mode. The unsuccessful flash attempts got me to screen informing me that Kies needs to be used to update my firmware. Kies showed a recovery code, which was downloaded, but unsuccessful. It would download all the way, but at the end of install, it would fail. Funny thing is it would work enough to get me back to the ability to get into download mode. I just want my Note 2 working again. Is there any way to wipe my phone completely clean, and start over? Or is there any way to even re-root it, or flash any sort of rom on there, just so I can use the damn thing? I need some help by you pros out there ! Please!
titostats said:
So I have an Att Note 2, which is bricked or soft bricked. I am a very rookie Android guy when it comes to modifying or hacking. I did root my Note 2 with Cyanogenmod. However, I missed S Note and the use of my S Pen so I researched a bit to get back to stock with the use of Odin and stock roms found on the net. I was successful, and actually amazed it worked. Long story short, a few days after that, an OTA update hit my phone, didn't even think about it and began the download. The phone downloaded the update, and rebooted to complete the install. The problem is, during reboot, the phone got stuck on the "Samsung Galaxy Note II" screen. I researched a bit online, and everyone said get to recovery mode and do a few things. Problem is, I can't get into recovery mode, I can only get the screen described above, and the download screen, THAT IS ALL. Looked a bit more online and attempted to flash various stock roms with Odin. Some were successful, Odin passed, and the phone would get stuck on the Note II screen again, and would not boot into recovery mode, same issue with only being able to access download mode. The unsuccessful flash attempts got me to screen informing me that Kies needs to be used to update my firmware. Kies showed a recovery code, which was downloaded, but unsuccessful. It would download all the way, but at the end of install, it would fail. Funny thing is it would work enough to get me back to the ability to get into download mode. I just want my Note 2 working again. Is there any way to wipe my phone completely clean, and start over? Or is there any way to even re-root it, or flash any sort of rom on there, just so I can use the damn thing? I need some help by you pros out there ! Please!
Click to expand...
Click to collapse
Download the latest kies from the samsung website.. and then open tools and then firmware update and initialization.. pull out the battery and type the model number and serial number kies asks.. follow the instructions.. your phone will be fine..
Sent from my GT-N7100
titostats said:
So I have an Att Note 2, which is bricked or soft bricked. I am a very rookie Android guy when it comes to modifying or hacking. I did root my Note 2 with Cyanogenmod. However, I missed S Note and the use of my S Pen so I researched a bit to get back to stock with the use of Odin and stock roms found on the net. I was successful, and actually amazed it worked. Long story short, a few days after that, an OTA update hit my phone, didn't even think about it and began the download. The phone downloaded the update, and rebooted to complete the install. The problem is, during reboot, the phone got stuck on the "Samsung Galaxy Note II" screen. I researched a bit online, and everyone said get to recovery mode and do a few things. Problem is, I can't get into recovery mode, I can only get the screen described above, and the download screen, THAT IS ALL. Looked a bit more online and attempted to flash various stock roms with Odin. Some were successful, Odin passed, and the phone would get stuck on the Note II screen again, and would not boot into recovery mode, same issue with only being able to access download mode. The unsuccessful flash attempts got me to screen informing me that Kies needs to be used to update my firmware. Kies showed a recovery code, which was downloaded, but unsuccessful. It would download all the way, but at the end of install, it would fail. Funny thing is it would work enough to get me back to the ability to get into download mode. I just want my Note 2 working again. Is there any way to wipe my phone completely clean, and start over? Or is there any way to even re-root it, or flash any sort of rom on there, just so I can use the damn thing? I need some help by you pros out there ! Please!
Click to expand...
Click to collapse
Try flashing a recovery for ur device with Odin, not a ROM, just flash twrp recovery with Odin, after u flash the recovery u will be able to access recovery and flash a stock ROM through twrp. I think what happened to u is when u flashed the update it tried to right over the unlocked bootloader which caused the soft brick, try flashing the recovery for ur device and if that doesn't work try the above posters way...
Sent from my Nexus 5 using XDA Premium 4 mobile app
Ok so I have a samsung galaxy s3 att and I have been rooted for the past month or so, no issues. Then, I decide to install a custom rom so I get a stable cm11 and attempt to flash it and it says my cwm version is too low so the reboot my phone so I can update it. The phone starts to boot and gets stuck on the att globe logo with the blue light pulsing. I shut off the phone, pull out the battery and try again, still nothing. I start getting scared so I restore the nandroid backup I made right before this custom rom incident and boot it, still gets stuck at the same place. I really need my phone fixed so can someone help me please??
I was talking to @sd_shadow on another forum earlier and was wondering if he could help me?
supy99 said:
Ok so I have a samsung galaxy s3 att and I have been rooted for the past month or so, no issues. Then, I decide to install a custom rom so I get a stable cm11 and attempt to flash it and it says my cwm version is too low so the reboot my phone so I can update it. The phone starts to boot and gets stuck on the att globe logo with the blue light pulsing. I shut off the phone, pull out the battery and try again, still nothing. I start getting scared so I restore the nandroid backup I made right before this custom rom incident and boot it, still gets stuck at the same place. I really need my phone fixed so can someone help me please??
I was talking to @sd_shadow on another forum earlier and was wondering if he could help me?
Click to expand...
Click to collapse
this thread may help
http://forum.xda-developers.com/showthread.php?t=2549068
"all i can really do , is stay out of my own way and let the will of heaven be done"
Don't panic
Grab the latest version of philz touch recovery https://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2lte/
The zips are made to be flashed from a recovery like cwm. Install it using cwm, reboot into recovery and philz should come up. You should be able to proceed with wiping and installing your custom rom at this point.
If the zip doesn't work out for some reason, you could also use Odin to flash a .tar.md5 from that link to update your recovery.
Try this: http://forum.xda-developers.com/showpost.php?p=60162192&postcount=2
Sorry for being a n00b. I am not a rooting n00b, just a n00b when it comes to the new Samsung security features.
I have a Tmo Note 3. I want to install a custom ROM and recovery. I tried (and failed) to follow the instructions in the thread. I'm a bit ADD, so following all the redirects messed me up. Here is what I did:
1) Followed direction in the CF Auto root thread. This did give me root and that still works.
2) Installed TWIRP for Tmo Note 3. This install went fine until I rebooted
3) when I rebooted I got an error that my recovery was not stock and got stuck in a boot loop.
4) Gave up and flashed back to stock
I'm running Android 5.0, have root through CF, what do I need to do to get a custom recovery (don't really care which) and a ROM on my phone?
Thanks and sorry again for being a n00b.
Did you do this?
AFTER THE ROM IS FLASHED, THE PHONE WILL REBOOT AND YOU WILL SEE A BLUE BAR FOR A FEW SECONDS, AFTER THIS BLUE BAR DISAPPEARS, THE PHONE WILL REBOOT AGAIN; AT THIS MOMENT YOU MAY WANT TO BE READY AND BE ALREADY PRESSING VOLUME DOWN + HOME BUTTONS. THE IDEA BEHIND THIS, IS TO CATCH DOWNLOAD MODE BEFORE THE OS (LOLLIPOP) ACTUALLY BOOTS FOR THE FIRST TIME. THIS WILL SOLVE THE CF-AUTO-ROOT OR TWRP NOT STICKING REPORTED BY SOME USERS
Thanks
TEKHD
Ok guys I am pretty sure I fubar'd my tablet.
I am stuck in a recovery loop. When I start the tablet it just goes back into recovery. Which if I still had TWRP I think I could still do something, but I flashed cyanogen recovery trying to flash cm13 since I cold not get anything else to work. I cannot boot into download/firmware update screen. The screen just flickers a little and goes dark.
A little background:
Started when tablet forced install of 5.0 update and I was in a recovery loop. I flashed 410 test build, rooted, flashed twrp, installed stock rooted ROM. Everything was fine. Then tablet did it again, this time I just flashed rooted ROM and factory reset. Even took the steps to fix the white lines and storage issues. Was working fine. Got home a few days ago and I was in a recovery loop again. But now I don't have the bootloader screen/download mode/firmware update screen (whatever you want to call it) so last night i tried to download cm13, Gapps and cyanogen recovery with no avail.
I can access adb on my PC while in recovery, but when I try to access ADB shell I get unauthorized something or other. Because I cannot authorize USB debugging, because ROM won't boot. I tried to flash stock rooted ROM from cyanogen recovery and it says not signed or something like that.
Does anyone have any ideas? I really think I have screwed the pooch here.
sent from a device using an app
title
if you have a stock recovery image flashing it is easy, i had a LOT of troubles with my v410 and still am working with it. i have mine rooted, just with TWRP though, i cant use xposed framework, which negates why i rooted this in the first place. anyway, through much grit and determination flash your stock image after wiping what needs to be wiped and doing all other necessary things. Then, you must download kingo root, supersu, superuser. flashify would help with the flashing i hear, but it has troubles with the v410. kingo root was an apk i managed to find buried under a million viruses on the 34th page of google..or something. rooted mine in one click, from stock to reboot to twrp root.. many glitches.
I need help myself, deleted my "Phone" system app, causing me to lose connectivity with my data plan. cant seem to restore it, and flashify nor twrp has been able to flash a custom recovery, or a backup, im at a loss.
Help? We seek the same thing.
Ok but how do I flash the stock recovery image. I can't use fastboot. ADB says I am unauthorized.
sent from a device using an app
Anyone have any other ideas?
I am at a complete loss. I am by no means a developer, but I do know my way around. I really think I have FUBAR'd this one.
Kind of stinks, I give up. Anyone want a bricked v410?
Sent from my Galaxy Tab 2 using Tapatalk