I have a 32GB d855 running 6.0 V30A-ZAF-XX, I put my phone on charge while it was off, charged it until 30% then decided to turn it on, after I booted into marshmallow, suddenly it was saying it is on 57% charge. Does anyone know why and is this a bug which ruins the battery?
t2can said:
I have a 32GB d855 running 6.0 V30A-ZAF-XX, I put my phone on charge while it was off, charged it until 30% then decided to turn it on, after I booted into marshmallow, suddenly it was saying it is on 57% charge. Does anyone know why and is this a bug which ruins the battery?
Click to expand...
Click to collapse
Try calibrating using any 'battery calibration' app. I had this problem which was hence solved.
Sent from my LG-D855 using XDA-Developers mobile app
Sreerag ag said:
Try calibrating using any 'battery calibration' app. I had this problem which was hence solved.
Sent from my LG-D855 using XDA-Developers mobile app
Click to expand...
Click to collapse
Do not use any battery calibration app!!!! It can harm your battery unless it has been proven to work on the G3.
Do this instead:
1. Discharge your phone fully until it turns itself off.
2. Turn it on again and let it turn itself off.
3. Plug your phone into a charger and, without turning it on, let it charge until the on-screen or LED indicator says 100 percent.
4. Unplug your charger.
5. Turn your phone on. It's likely that the battery indicator won't say 100 percent, so plug the charger back in (leave your phone on) and continue charging until it says 100 percent on-screen as well.
6. Unplug your phone and restart it. If it doesn't say 100 percent plug the charger back in until it says 100 percent on screen.
7. Repeat this cycle until it says 100 percent (or as close as you think it's going to get) when you start it up without being plugged in.
8. Now, let your battery discharge all the way down to 0 percent and let your phone turn off again.
9. Fully charge the battery one more time without interruption and you should have reset the Android system's battery percentage.
Remember that it is not recommended to perform this process all the time. Even when your battery is so dead your phone won't even turn on, your battery still has enough reserve charge to avoid system damage. But you don't want to poke the tiger with a stick. Perform this process once every three months at the most. If it is required more often than that you have bigger problems at hand.
Put plainly: fully discharging a battery is bad for it. Trying to overload a battery is also bad for it. The good news is that charging batteries automatically shut off when their safe limit is reached and there's always a little in reserve even if your phone won't start. But again: do this only when really necessary, because it does have a negative impact on battery life.
Guide taken of androidpit.com but it is very effective...
aaronkatrini said:
Do not use any battery calibration app!!!! It can harm your battery unless it has been proven to work on the G3.
Do this instead:
1. Discharge your phone fully until it turns itself off.
2. Turn it on again and let it turn itself off.
3. Plug your phone into a charger and, without turning it on, let it charge until the on-screen or LED indicator says 100 percent.
4. Unplug your charger.
5. Turn your phone on. It's likely that the battery indicator won't say 100 percent, so plug the charger back in (leave your phone on) and continue charging until it says 100 percent on-screen as well.
6. Unplug your phone and restart it. If it doesn't say 100 percent plug the charger back in until it says 100 percent on screen.
7. Repeat this cycle until it says 100 percent (or as close as you think it's going to get) when you start it up without being plugged in.
8. Now, let your battery discharge all the way down to 0 percent and let your phone turn off again.
9. Fully charge the battery one more time without interruption and you should have reset the Android system's battery percentage.
Remember that it is not recommended to perform this process all the time. Even when your battery is so dead your phone won't even turn on, your battery still has enough reserve charge to avoid system damage. But you don't want to poke the tiger with a stick. Perform this process once every three months at the most. If it is required more often than that you have bigger problems at hand.
Put plainly: fully discharging a battery is bad for it. Trying to overload a battery is also bad for it. The good news is that charging batteries automatically shut off when their safe limit is reached and there's always a little in reserve even if your phone won't start. But again: do this only when really necessary, because it does have a negative impact on battery life.
Guide taken of androidpit.com but it is very effective...
Click to expand...
Click to collapse
This is an alternate method. The simpler way OS to use the app called 'Battery calibration by NéMa'. The usage instructions are provided with the app. That is, to full charge it after calibration.
I've did this some times because changing roms sometime cause incorrect battery status. And it have not damaged my phone or battery.
Sent from my LG-D855 using XDA-Developers mobile app
Related
Does anyone have a link for the thread that discussed the correct way to wipe battery stats when upgrading to a new Rom? I remember it went something like drain dead, charge to full, drain dead again then charge to full and wipe stats. I can't remember the complete process. Thanks for the help.
Sent from my PC36100 using XDA App
I've seen a couple different threads on that here, one saying discharge fully then charge while powered off, and the other saying to do a full charge "conditioning cycle". I did the latter and it seems to have made a difference.
Here's what I did:
Charge the phone fully with it powered on
When fully charged, disconnect cable
After green LED goes off, power the phone off
When phone is fully powered off, reconnect cable, amber charging light should be on
When LED goes green, disconnect cable
Repeat previous two steps 10 times
After 10th cycle, boot into recovery and wipe battery stats.
I am using Amon Ra recovery which has the wipe battery stats option under the Wipe option. I never did this when I had Clockwork recovery installed, so I don't know if the option is in the same place.
Being an electrical engineer, I find this business of battery conditioning interesting, along with the Ni-Cd "memory" vs. Li-Ion "no memory" issue. If anyone has found a decent physics-based explanation as to why these things do or do not have any basis in fact, I'd appreciate a link. Yes, I'm too lazy to Google it at the moment.
Hmm, I may have to look into this again. I charged my phone all night (powered off) and unplugged it this morning. I did nothing with it this morning but turn it on and look at it, then put it in standby (quick press of power button). It lost 16% of charge in less than 2 hours!
I'm running BS1.2 with the Baked1 (low voltage/best battery) kernel.
Damn, just installed System Panel and found that my CPU is at 100% constantly!
I'm trying this now. The longest I've pushed my battery was 22 hours... and that was with 39 minutes of screen on time, lol. In standby almost the entire 22 hours....
Ok, I believe my issue was related to a camcorder problem, my CPU usage has dropped back to normal levels after fixing that separate problem. After my battery recharges fully I will see what happens with the charge.
the other methods to do "calibrate your battery" (which isnt really calibrating the battery but the battery stats of the phone so it can accuratly judge when it stops and starts charging)
1) charge the phone to full
2) unplug and use phone till it shuts off from no battery (do not plug in until it shuts off)
3) charge phone to full again with out unplugging till 100% (check under about phone > battery it shoudl say full charge there)
this should reset the battery stats.
the last method is one from HTC
1)Charge the phone for 8 hours uninterupted with power on
2) turn off the phone and charge for an additional hour
3) turn ont he phone unplug it and let it sit for 2 minutes then plug it in for an additional hour.
all 3 methods listed should help. I personally dont like the x10 method because it has the potential and basically over charges the battery to make sure it is acctually at a full charge. It is much faster then the other 2 methods though so to each there own.
Dont waste your time on...
plug/unplug 10 times. It really doesn't recal the battery.
the unplug/plug 10 times.
1. Phone on...charge until green light comes on. Immediately unplug and turn phone off.
2. Plug phone back in until green light comes on again. Immediately boot into Recovery and wipe battery stats.
3. Use the phone on battery until dies.
4. recharge phone to 100%
You are good to go!
If I tether during the day (5+ hours) a lot, is it bad on my battery? Isn't that like a constant charge or does once the LED turn green it stops trying to charge?
Thanks.
fldash said:
If I tether during the day (5+ hours) a lot, is it bad on my battery? Isn't that like a constant charge or does once the LED turn green it stops trying to charge?
Thanks.
Click to expand...
Click to collapse
the evo doesnt do a trickle charge so when the light turns green it stops, this is why you will almost always drop 1-5% battery rather quickly.
Are you sure? My light has been green for a while, and my phone battery status says 'Full'.
fldash said:
Are you sure? My light has been green for a while, and my phone battery status says 'Full'.
Click to expand...
Click to collapse
There's a lot of confusion over how the battery / charging circuit works and how it reports. My advice is to just charge until it's green and full, then unplug it. If you leave it plugged in all night, unplug it for 10 mins in the morning, then plug it back in to top off.
That doesn't really help me SilverZero, my question is only if leaving it tethered (which means connected to USB) is bad for my battery.
Well on mine i would check it every once in awhile and i would see that once it get downs to under 90% that it would charge again till it recognized that it was full again. So based on that i dont think you should have to worry about it. It seems to only draw the charge when needed. I also leave mine plugged in alot when im home so its good to go when i leave and havent noticed a loss of battery life at all.
You guys don't want the charger to trickle charge. Li-Ion does not accept overcharge, even 0.01C (15 mA on the stock Evo battery) will cause it to vent and probably combust.
So does "calibrating the battery" calibrate the phone or the actual battery?
I ask because I have 3 spare batteries, wondering if I have to do this for each of them??? They are all standard size, one of them OEM
So, I'm on my Evo today, playing a game (Air Strike). My battery is at 93% when I picked the phone up to play, and the phone is plugged in. Suddenly, with no warning what-so-ever, my phone shuts off. Of course a mini-freak out and many "wtf's" ensue. No warning, no signs, even the led went off. I pulled the battery, put it back, then plugged the phone in again. After that it gave me the blinking light indicating the battery was too low to turn on. After a few minutes charging she came back on and battery was at 5%.
How the hell does a battery go from 93% to 0% in less than 5 minutes, and give no warning at all?? Anybody else ever have this problem?
Wow I've have never heard or that happening before. Maybe a glitch in the battery stash? Did it take awhile to charge up to 100%? Can you reproduce the issue again?
Sent from my EVO (CM 6.1.1) using XDA App
I had this problem with my older phone once. The battery itself may have a problem or your phone is not getting charged properly.
Try These :
1) Try charging the phone overnite from the Wall charger (Not through USB of your computer)
2) If the above does not work, and you have access to another evo battery, then try using that.(try using a friends battery and charger for a day. ) (Ofcourse needless to say the charger and battery must be for Evoonly )
In my case, my phone started working fine again after getting my battery & charger replaced.
Probably shouldn't worry about it too much just yet. Could be something as simple as your battery meter was mis-calibrated. The meter itself is software so it can easily be wrong/off. If it continues you may have a bad battery.
Sounds to me like something is wrong. Did you just get the phone or have you had it?
Idk... The phone had been plugged in for most of the day (hadn't gone anywhere. Lazy day lol) And like I said, the led went completely out as well.
Haven't had the problem again, so we'll see I guess....
Mark_Hardware said:
Idk... The phone had been plugged in for most of the day (hadn't gone anywhere. Lazy day lol) And like I said, the led went completely out as well.
Haven't had the problem again, so we'll see I guess....
Click to expand...
Click to collapse
I've seen some posts about the Evo battery shutting off the charge when its being used. Were you using your Evo while it was charging?
If the battery doesn't seem to be giving you percentages that are accurate, you might want to recalibrate your battery.
Common misconceptions sticky (Evo Q&A) said:
Battery recalibration (Thanks to Cyanogen for this and to fachadick for bringing it to my attention).
If you're experiencing higher than normal battery drain, try the following:
1. Charge the phone to full battery; let it keep charging until the battery says it is fully charged. Do not just wait until the light is green, it isn't always fully charged, causing a lot of inaccuracies. (You can check by going to: Settings -> About Phone -> Status -> Battery Level = Full.)
2. Boot to recovery and wipe battery stats.
(To have the most accurate of battery stats, reboot the phone immediately after wiping the battery stats and wait for your ROM to boot completely to the desktop. Once your entire boot is done and you have full access to the phone, go ahead and pull the charger and continue.)
3. Do not charge the phone until after draining the battery completely, resulting in it automatically shutting off. Take out the battery, and keep trying to turn on your phone until it will not turn back on at all.
4. Recharge the phone completely and then use as you normally would.
This is a method that has been proven to work, I am sure there are other ways. My battery lasts longer after doing this and the reading is much more accurate. It might be advisable to do this after every ROM install if you want the most battery life and most accurate battery reading by the phone's software.
Click to expand...
Click to collapse
ok so i got a problem with my battery
my battery on my phone just going out to fast
for example today
i connected it so it could reload and then
when i disconnected it was 100%
then after 2 hours only that i havnt use the phone i mean havnt touched it even once
i look again on battery life and here it says 36%
and it keep going every day
can some1 tell me why it keep happening???
WOW! That's a major drain in 2hours.
My 2 cents are on a defective battery - since the phone was on standby.
You can try some tutorials on adjusting the power saving settings (like screen brithgness what to turn off and not etc.)
Also you might try caibrate the battery.
there is a thing like u charge it to 100% ,unplug from the charger and turn the phone off ,then plug in again and charge to 100% again... there is a thread about it on this forum, do a lil search it might help u
Dial *#*#4636#*#* and go to battery and find partial wake usage, here the apps are listed that prevent the phone form sleeping and thus causing battery drain. Also check the % under Settings-about phone- battery usage to see what app or process consumed the most battery.
Does it get very hot? I mean - if the battery really contains 1500mAh (which I doubt in this case) and drains completely in 3 hours, that's 500mAh, so 3.5V*0,5A=1,75W continuesly.
You really should notice that while it's in your pocket...
no the phone isnt getting hot
i mean it can sit on my pocket for like 2-3 hours and then it suddenly 3x %
without even touching it
Try these steps:
1. Please connect the phone to the charger with the phone powered on, and allow the phone to charge until the notification LED is green, indicating the device is fully charged.
2. Disconnect the phone from the charger, and power it off.
3. Reconnect the phone to the charger with the phone powered off, and allow the phone to charge until the notification LED is green.
4. Disconnect the phone from the charger and power it on. Once the phone is powered completely on, power it off again and reconnect it to the charger until the notification LED is green.
5. Disconnect the phone, power it on (OPTIONAL: Enter Recovery at this point and Wipe Battery Stats (from Advanced menu), and use it. You need to use this sequence only once.
If that does not solve it you have a defective batterie.
ok i will try it
but can u tell me what the point???
i mean what does it do??
NoneSkillZ said:
ok i will try it
but can u tell me what the point???
i mean what does it do??
Click to expand...
Click to collapse
The point of that, is to make the battery life longer. And actually it works. I tried when i bought my phone an the increase was significant!
Edit: Just saw in another thread that some newer custom ROMs has some things messed up, and they eat the battery more than normal when the screen is off. You might take a look at it.
yea i did all the steps and its not working
the battery still going down rapidly
so i should buy new one??
Yeah.
BTW, are you on a stock rom?
srry
no idea what stock rom means
but im on miui rom
Hey what's up. I got this G2 with the latest cm7, which is build number 21 and the battery life is horrible. Like 8 hours with an hour of the display being on. I'm coming from the Epic which had pretty good battery life once calibrated.
So what's the proper way of calibrating the G2? I am using the stock kernel that comes with the Cm7 rom right now but I did try the pershoot kernel couple times and underclocked it but it still didn't help. I think all that kernel flashing messed up my battery life. So any ideas? Thanks!
Sent from my HTC Vision using Tapatalk
saywhat4118 said:
Hey what's up. I got this G2 with the latest cm7, which is build number 21 and the battery life is horrible. Like 8 hours with an hour of the display being on. I'm coming from the Epic which had pretty good battery life once calibrated.
So what's the proper way of calibrating the G2? I am using the stock kernel that comes with the Cm7 rom right now but I did try the pershoot kernel couple times and underclocked it but it still didn't help. I think all that kernel flashing messed up my battery life. So any ideas? Thanks!
Sent from my HTC Vision using Tapatalk
Click to expand...
Click to collapse
Charge your phone all the way to 100% (not just until the LED turns green, which is around 90%), unplug and boot into recovery, wipe battery stats, boot back into Android and use your phone until the battery drains and your phone shuts off. Keep trying to power up until it won't any more.
Now, plug your phone in (into the wall, not a computer) and charge until full *without* turning it on. Remember, the LED turns green around 90% so you'll need to leave it another few hours after the LED changes. Once you're full, unplug and boot into Android and again use it until the battery is fully drained and you can't power up anymore and you're good to go.
Remember, after wiping stats, during the draining process *do not* plug it in to the charger or your computer as thiss will mess up the calibration.
Its a pain, and takes a day or so, but its worth it. To speed up the draining process, do some process intensive things (video watching, game playing, etc.)
Sent from my T-Mobile G2 using XDA App
OriginalGabriel said:
Charge your phone all the way to 100% (not just until the LED turns green, which is around 90%), unplug and boot into recovery, wipe battery stats, boot back into Android and use your phone until the battery drains and your phone shuts off. Keep trying to power up until it won't any more.
Now, plug your phone in (into the wall, not a computer) and charge until full *without* turning it on. Remember, the LED turns green around 90% so you'll need to leave it another few hours after the LED changes. Once you're full, unplug and boot into Android and again use it until the battery is fully drained and you can't power up anymore and you're good to go.
Remember, after wiping stats, during the draining process *do not* plug it in to the charger or your computer as thiss will mess up the calibration.
Its a pain, and takes a day or so, but its worth it. To speed up the draining process, do some process intensive things (video watching, game playing, etc.)
Sent from my T-Mobile G2 using XDA App
Click to expand...
Click to collapse
Thanks for the tip. Now I have been doing some reading and saw some people recommended charging the phone while it is on when it is fully discharged the first time. You recommend while its off? Does it make a huge difference?
saywhat4118 said:
Thanks for the tip. Now I have been doing some reading and saw some people recommended charging the phone while it is on when it is fully discharged the first time. You recommend while its off? Does it make a huge difference?
Click to expand...
Click to collapse
I don't think it would make that big of a difference; if you think about it though, you're dealing with the battery and battery only if the system is turned off.
Sent from my T-Mobile G2 using XDA App
True we are dealing with the battery but when we wipe the battery stats I think it only wipes the battery information the phone had in its system. So if we wiped the stats when it is full then let it discharge till completely empty, im assuming, you would have to charge it while its on so the phone can now learn what the battery level is and when its full and its capacity. I'm just guessing I could be wrong though. I'm just going to try both and see what happens.
Sent from my HTC Vision using Tapatalk
OriginalGabriel said:
Charge your phone all the way to 100% (not just until the LED turns green, which is around 90%), unplug and boot into recovery, wipe battery stats, boot back into Android and use your phone until the battery drains and your phone shuts off. Keep trying to power up until it won't any more.
Now, plug your phone in (into the wall, not a computer) and charge until full *without* turning it on. Remember, the LED turns green around 90% so you'll need to leave it another few hours after the LED changes. Once you're full, unplug and boot into Android and again use it until the battery is fully drained and you can't power up anymore and you're good to go.
Remember, after wiping stats, during the draining process *do not* plug it in to the charger or your computer as thiss will mess up the calibration.
Its a pain, and takes a day or so, but its worth it. To speed up the draining process, do some process intensive things (video watching, game playing, etc.)
Sent from my T-Mobile G2 using XDA App
Click to expand...
Click to collapse
I have used this method to calibrate the battery and can say that it does have a pretty big impact on battery life. +/- 20% in my case. I also find that I need to re-calibrate roughly once every month or so.
To be clear, there is not such thing as "calibrating the battery", you are calibrating the battery meter (volt meter) on the phone. Maybe its just a semantic distinction, and that is what the OP and subsequent replies are talking about. But many people get this confused, due to the old process of "conditioning" NiCad batteries, which is not applicable to modern cell phone (Li ion) batteries.
In my understanging, you aren't going to increase battery life by doing any of the above, but only making the battery meter more correctly read how much power is left. For instance, if the meter is not properly calibrated, it may read lower than it should. So people think they are increasing their battery life.
I would discourage from discharging the battery to empty. Over discharge of Li ion batteries can possibly (not often, but in a small percentage of cases) prevent the battery from taking a charge. There is a safety circuit which is supposed to prevent over discharge, but it does not always work. Therefore, Li ion batteries should not be discharged lower then 20% whenever possible. Most of us do it from time to time on accident, but there is not reason to do it intentionally. Charge the battery to 100%, drain to 20%, and repeat a couple times. This will get your battery meter plenty accurate. Draining it to empty does not really gain you anything (the battery meter is not that accurate in the best of circumstances, anyway), and can harm the battery.
http://batteryuniversity.com/learn/article/do_and_dont_battery_table
Flashing a new ROM resets the battery meter. So until its properly calibrated, it will give you junk readings. This is one reason why people often jump the gun and think that a custom ROM is getting them poor battery life. Calibrate the meter, and use the ROM for a couple days, then you should get a real indication of what the battery life is like on that ROM.
redpoint73 said:
I would discourage from discharging the battery to empty. Over discharge of Li ion batteries can possibly (not often, but in a small percentage of cases) prevent the battery from taking a charge. There is a safety circuit which is supposed to prevent over discharge, but it does not always work. Therefore, Li ion batteries should not be discharged lower then 20% whenever possible. Most of us do it from time to time on accident, but there is not reason to do it intentionally. Charge the battery to 100%, drain to 20%, and repeat a couple times. This will get your battery meter plenty accurate. Draining it to empty does not really gain you anything (the battery meter is not that accurate in the best of circumstances, anyway), and can harm the battery.
Click to expand...
Click to collapse
I was about to post this. Letting a LiIon discharge all the way is more harmful to the battery than recharging it mid drain cycle.
I'm having a bit of battery issues, I haven't flashed a ROM or calibrated my battery meter. So I charge my phone to full while still on, unplug it and drain it until it turns off (NOT until the battery is completely drained, which could potentially damage the battery), plug it up and let it charge while off, and I should be calibrated?
Do you need to have root to be able to reset battery stats?
Sent from my T-Mobile G2 using XDA App
So, I bought another battery. Will this sort it?
Also, what's the usual procedure?
Should I charge the battery to full in the phone (turned off) then boot, set up, then charge again and reset battery stats?
The problem is that the battery control chip doesn't take into account that the battery ages.
Resetting battery stats or charging while turned off will only clear the stats you see in the settings menu. This guide will make your battery drain to 0% again: http://forum.xda-developers.com/showthread.php?t=1534892
I don't know what a new battery will do though.
I gathered that, but as the phone is going to a new user (my stepson) we got him a new battery anyway
I just wondered what the correct procedure is. I know you need to do a first charge with a new battery, as with a new phone, however, this phone obviously has a working ROM already on it.
So, the phone is charging now, switched off. Should I turn it on, use a little, then use the battery calibration app to delete the stats and then drain to 0%?
Kryten2k35 said:
I know you need to do a first charge with a new battery, as with a new phone
Click to expand...
Click to collapse
Well, that assumption is probably inherited from the NiHM batteries in the past, because it's not needed with Li-Ion batteries. In fact charging to 80% is better than charging to 100% and keeping it plugged in.
You can read more about it here and here.
Kryten2k35 said:
So, the phone is charging now, switched off. Should I turn it on, use a little, then use the battery calibration app to delete the stats and then drain to 0%?
Click to expand...
Click to collapse
Just charge it and use it for a full cycle. If it shuts down at 15%, you can try the battery calibration from the thread I mentioned above. If it doesn't, you're battery capacity is the same as the one the battery chip has calculated, which is good.
So, why does the first charge take so long?
This thing is still charging and it's been on the charger for 3 hours, whereas usually it'd be charged fully by now.
Been like that for every Li-Ion battery I've ever had (including my S3, took around 6 hours to charge, usually takes 3).
EDIT:
Just to clarify, I don't intend on leaving it past the green light. As soon as it says it's full I'll be taking it off charge and not trying ot overcharge it. But I still have the orange charging light after 3-4 hours.
To be honest, I don't know. Maybe it's a safety to prevent overcharging. Coincidentally, I've got exactly the same issue now. I asked about it in the calibration thread. I suppose it's normal, but I'm not sure about that.
Kryten2k35 said:
So, why does the first charge take so long?
This thing is still charging and it's been on the charger for 3 hours, whereas usually it'd be charged fully by now.
Been like that for every Li-Ion battery I've ever had (including my S3, took around 6 hours to charge, usually takes 3).
EDIT:
Just to clarify, I don't intend on leaving it past the green light. As soon as it says it's full I'll be taking it off charge and not trying ot overcharge it. But I still have the orange charging light after 3-4 hours.
Click to expand...
Click to collapse
my battery took just over 6 hours to charge the other day from completly dead
Sent from my HTC Desire