Does anyone know how I can find out the mac address of my xda IIs ? I have a dreytek wireless router at home which uses a mac based access control list. I've tried the addresses that appear in wireless LAN manager ( BSSID and MAC ) but no joy. The only way I can connect is to switch off the access list feature completely
jeff
Hi Jeff,
Switch off the Access control, and let the XDA IIs join the wireless network. Then go into Diagnostic Tools --> View DHCP assigned addresses, and you will get a list of MAC addresses, IP addresses and hosts on the network. Match your phone's name to the MAC address.
Then you can turn access control on again and input the phone's mac address into the "allowed" list.
Thanks for the reply. I've kind of done that as you can see from the DHCP table below
DHCP server: Running
Index IP Address MAC Address Leased Time HOST ID
1 192.168.1.1 00-50-7F-23-97-CC ROUTER IP
2 192.168.1.10 00-00-00-00-00-00 BAD IP
3 192.168.1.11 00-0D-61-4E-A7-F7 0:00:04.600 hubbo
4 192.168.1.12 00-09-2D-0E-49-61 9:24:34.170
(not sure about that BADIP line ! )
I would say my MAC is 00-09-2D-0E-49-61 but it's still not working.... odd.
Is there no way that you can tell the MAC address from the phone without connecting to a network.
Here is a freeware that will allow you to find your MAC with no connection. I used it on my PDA2K.
http://www.freewareppc.com/communication/vxipconfig.shtml
Install on your device. Just turn the wifi on and run the program and it will give you the MAC and additional device info. Don't have the PPC connected to the USB or it will identify that device.
Sorted thanks, whilst in PC World I scanned for a Wireless network, and found three, hehe! Once connected used that utility to get my MAC.
Many thanks!
wifi and drayteck router
hi i see u have a draytech router how did u manage to get streaming video? i have been trying now for hours.I can get the video on my laptop without any problems but my m2000?????
i think the problem lies within the vpn settings as when i try to open http://house:8080 i get the message vpn connection required.
any help would be greatly recived (i have the vigor 2600g)
thanks in advance
delboy
im trying to get an internet connection through my wifi connection. i have done search's and lots of people seem to be asking the same question but nobody has the answer.
at the moment i can access my c: using an application called Resco explorer. but i can not connect to the internet. im not sure what setting i should have on the wifi manger and on my pc. im also using AOL as my isp.
PLS PLS help :lol:
Edit:
also i can not connect to activesync (version 3.8.0) via wifi. maybe if i was able to connect to this the internet would work as it does when its docked??????
looks like a no then
I got mine working but setting my wireless network adapter to connect to "Work".
Under Settings>Connections>Tasks>Manage existing connections>Proxy Settings> check the "This network connects to the internet" box
then
Under Settings>Connections>Advanced>Select Networks> "Programs that automatically connect to the internet should connect using:" to "My Work Network" (and the same with one for private network)
Also in your active sync settings, make sure your connection settings allow network (Ethernet) and RAS connections.
From previous research around this, i'm pretty sure you can only use the internet pass through under "WORK" settings only.
*thought i'd better register and contribute as i've gained a fair bit from this forum.
no good anyother ideas. i have searched through hundreds of threads and still no go
help pls
Make sure you have "Enable Netbios over TCP/IP" checked in your TCP/IP Advanced settings.
i have done this on both my wifi network and my isp network.
still not working
Have you checked if you're getting an IP address from your Wireless Router's DHCP server? Also DNS settings and Gateway address should be there.
You can check this easily by using vxUtil (free )
these are my settings:
tiacxwln1 - tiacxwln compatible wireless
Ip address 192.168.0.2
subnet mask 255.255.255.0
default gateway 192.168.0.1
primary DNS 192.168.0.1
secondary dns
primary wins
seconfdary wins
DHCPs server 192.168.0.1
under serial usb
IP address 192.168.55.101
subnet mask 255.255.255.0
default gateway 192.168.55.100
primary DNS 127.0.0.1
Getting this error when I tried to allow my broadband connection to share with my wifi connection. If I unplug the wifi connection and try and share with another network I don’t get any errors.
Internet connection sharing (ics) cannot be enabled due to IP address conflict on the network. ICS requires the host be configured to use 192.168.0.1 please ensure that no other client on the network is configured to use 192.168.0.1
hmmm ... ever had the same problem. all devices are able to connect to the same router except mine sx66.
then i change the router's channel to '1' .. tada .. now everyone is connected. it might sounds silly, but it worked for me.
try changing your ap wireless channel.
Re: does NE1 have the answer to wifi not connecting to the n
robboy said:
Edit:
also i can not connect to activesync (version 3.8.0) via wifi. maybe if i was able to connect to this the internet would work as it does when its docked??????
Click to expand...
Click to collapse
i found the problem with activesync 3.8 and 4.0 somehow, so i reverted back to 3.7, now wifi can sync.
afaik, connecting to internet has nothing to do with activesync. its a direct connection to wifi router. use work location and check the proxy settings if u hv any? (at home i use connect to internet without proxy, at work i use connect to internet with proxy).
Also, for Activsync with wifi, make sure that the WINS server address is that of yr PC u want to sync with.
Is there some tutorial/help on using hte Remote Desktop Mobile to connect to a PC? I haven't been able to connect TP 2 to my PC running Vista. I put in the Computer name, User name, password, and domain and when I clicked "Connect", it returned an error:
Cannot connect. Likely reasons are:
1. specified computer name or ip does not exist.
2. A network error occured while establishing connection.
I tried both domain name and ip. Made no difference.
I also tried both on 3G as well as WiFi but it made no difference.
You'll need to set up two things:
set the vista machine to accept the remote connections
http://howtogeek.com/howto/windows-vista/turn-on-remote-desktop-in-windows-vista/
forward port 3389 on your router if you have one
http://portforward.com/
Then you should be up and running!
'tunes
Thanks, mad-tunes. Got it working now, at least when connected by WiFi. And when the phone and the PC are on the same Wifi network, I can connect simply by putting in the computer ip address. No domain is required and no port configuring required too.
Lord_BlackAdder said:
Thanks, mad-tunes. Got it working now, at least when connected by WiFi. And when the phone and the PC are on the same Wifi network, I can connect simply by putting in the computer ip address. No domain is required and no port configuring required too.
Click to expand...
Click to collapse
Good stuff, glad it helped a bit....
If you can't connect from the outside world (ie, using GPRS), then it's most probably a port forward thing...
If you want to get this bit working: How's the machine you're trying to RDP to connected to the 'net exactly?
(ADSL modem, router etc?)
mad_tunes said:
Good stuff, glad it helped a bit....
If you can't connect from the outside world (ie, using GPRS), then it's most probably a port forward thing...
If you want to get this bit working: How's the machine you're trying to RDP to connected to the 'net exactly?
(ADSL modem, router etc?)
Click to expand...
Click to collapse
Yes, the PC is behind the router. So probably woould need to do port forward as you have suggested. Having tested it yet. Would try this out later this week.
I was wondering, is theres a way to do this if youre on a home edition of windows?
the home edition I dont believe has remote desktop.
Remote desktop mobile using 3G connection
Has anyone gotten remote desktop mobile to work using only a 3G connection? I've got it working perfectly using wifi but can't for the life of me figure out how to do it over 3G. I searched and the closest thing I could find to being helpful was the following:
I had the same problem till I created two VPN connections. One for internal use (WiFi) and one for extenal use (3G).
The internal one uses the internal IP address of the VPN server and the external one uses the external IP address.
You have to sleect which connection you want to use before starting the connection depending on whether u r using WiFi or 3G.
Hope that makes sense. It works 4 me.
Click to expand...
Click to collapse
This makes sense but it's confusing about what to change in the VPN connection settings. Can anyone explain in more detail?
Thank you very much
squirtpunk said:
I was wondering, is theres a way to do this if youre on a home edition of windows?
Click to expand...
Click to collapse
No. You can only use third party solutions like VNC. RDP host is not included in Home Edition.
You have to go into your router and set up a port forward so that 3389 goes to internal IP address of the system you want to remote into. If you have port forwarding/triggering, you can have a different port (eg, 3390) trigger to 3389 internally. If you don't have port forwarding, you can change the listening port from the default 3389 to, eg, 3390 and then you can create a port forward to remote in that way. To access, add :3390 to the end of the remote address (eg, 64.246.222.91:3390). The registry path to the listening port is:
HLKM\SYSTEM\CurrentControlSet\Control\Terminal Server\WinStations\RDP-Tcp\PortNumber
You must reboot after changing the setting.
If you have a domain, it is incredibly useful to set up DNS for this, then you can simply enter the DNS name in the client. This works internally as well.
Update: So i just went to a Starbucks and tried using the wifi there to connect to my remote desktop and it couldn't connect!? But it can connect when I'm using the same wifi router as my remote computer does this mean I don't have the router properly port forwarded? Or is it some other issue? Any advice would be great.
Thanks
When you use your wifi at home, it ends up in the same IP subnet as the remote computer, so all you need to do is to enter the computer name.
When you're at a hotspot, you need to enter the public IP address for your router and step up port forwarding. Wifi outside of your home is no different from using EVDO as far as IP addressing is concerned. You must enter via public IP.
If you don't know what your public IP address is, open a browser from any computer at home and go to this URL:
http://whatismyip.com
It will tell you what the public IP is.
Cheap Loop-Hole
I got Remote Desktop to work on 3G.
First open Opera (or what ever your default browser is) set a home page to something that takes at least 5-10 second to load (if longer, even better), like an email account or m.myspace.com. Simple sites like m.google.com won't work because they load to quickly.
Close OPERA: I mean make sure its closed not just minimized.
This next part needs to be done rather quickly, so I advise making Remote Desktop a top icon in your Start Menu.
So Launch opera, and quickly launch Remote Desktop and hit connect.
Remote Desktop will piggy back off the Opera browser connection to get out to your computer.
Note: (make sure remote desktop works at home first, either by wifi, blue tooth, or direct usb, and by checking it from a computer outside of your network) once you know it works you should be able to connect to it.
Also note: as some one stated above, make sure that proper ports have been open on the computer and router than you should be good to go.
I'm sure their is a registry fix to get the remote desktop working without doing this, but this is the only way I've been able to do it for now..
Hope this helps...
---
I'm currently using AT&T Tilt 2 Stock Rom and Radio.
Check this out guys, it might be of some help: http://forum.xda-developers.com/showthread.php?t=533664
Thanks a lot guys! It's working just fine now (on both wifi and 3G!) turns out I didn't have the router properly port forwarded.
just started trying to figure this out today. spent about 15 minutes but couldnt get it going.
just installed windows7 on my old pc and im trying to get my htc tp2 (rhodium) to work with the preinstalled Remote Desktop Mobile application. i forwarded port 3389 on both tcp and udp since i didnt know which was necessary.
is a static ip necessary to get this setup by going into the ipv4 settings? also, what is the application looking for with the input for "domain"? - subnet mask? default gateway for my home network?
so far i have tried the following inputs in my tp2 for Remote Desktop Moble:
Computer: public ip
User Name: windows7 login name
password: windows 7 login password
domain: ???
any help is appreciated. going to try this more when i get home from work.
apathyps said:
just started trying to figure this out today. spent about 15 minutes but couldnt get it going.
just installed windows7 on my old pc and im trying to get my htc tp2 (rhodium) to work with the preinstalled Remote Desktop Mobile application. i forwarded port 3389 on both tcp and udp since i didnt know which was necessary.
is a static ip necessary to get this setup by going into the ipv4 settings? also, what is the application looking for with the input for "domain"? - subnet mask? default gateway for my home network?
so far i have tried the following inputs in my tp2 for Remote Desktop Moble:
Computer: public ip
User Name: windows7 login name
password: windows 7 login password
domain: ???
any help is appreciated. going to try this more when i get home from work.
Click to expand...
Click to collapse
network-wise what you need to do depends on how your PC's connected to the 'net...
if it's connected directly via something like a USB ADSL model or Virgin media cable box, then you'll only need to let 3389 through your PCs firewall.
If it's connected via anything like a router, then you'll also have to allow 3389 through your routers firewall, as well as forwarding port 3389 to your machine inside your network.
it's the port forwarding which needs the internal IP of your PC, so a static one's a good idea (otherwise, if your PCs internal IP address changes it'll stop working). you could set your router to always hand the same IP to your PC MAC address, which can be the best of both worlds (and how I do it).
http://www.portforward.coms a good place to start to find how to forward ports for your router if you're using one..
You also have to go to control panel>system>advanced system settings>remote and set things as you need in the 'remote desktop' section.
if you don't have the 'remote desktop' section, then you're running one of the home versions of the OS which doesn't support Remote desktop conenctions (out of the box )
re domains...if its a normal home PC and nothing to do with a business, then you wont have to enter one at all.
Once you're at home, get your TP2 on your internal network (wifi), and then try to rdp to your machine using its INTERNAL ip (192.168.*.*) and see if that works.
if it does, the PC end's fine and it's your router config you need to get right. if it doesnt, then its something at the PC..
post back here if you still have trouble..
ok, so connecting with the tp2 via 192.xxx.x.x works fine from within the network at home on wifi.
however, once i try and connect with the public ip, it doesnt work. did the port forwarding thing.
i setup the static ip, i tried putting the host pc in the dmz, and still nothing. i tried disabling the host pc's firewall, and nothing.
in remote desktop mobile, im putting in the public ip of the host pc, and have tried filling in the username and password fields, and also tried leaving them blank.
any ideas?
apathyps said:
ok, so connecting with the tp2 via 192.xxx.x.x works fine from within the network at home on wifi.
however, once i try and connect with the public ip, it doesnt work. did the port forwarding thing.
i setup the static ip, i tried putting the host pc in the dmz, and still nothing. i tried disabling the host pc's firewall, and nothing.
in remote desktop mobile, im putting in the public ip of the host pc, and have tried filling in the username and password fields, and also tried leaving them blank.
any ideas?
Click to expand...
Click to collapse
if its workin from inside your network, your PCs set just fine...so it must be the firewall or port forward on your router...
double-check that 3389s alowed through its firewall
and
the forwards set to point UPD+TCP on port 3389 to the current internal IP of your PC.
tbh, I cant think of much else but let me know how you get on
ah, got it working. had to forward from ANY -> 3389, not 3389->3389. duh. works now.
thanks guys
Strange, you shouldn't have had to. RDP defaults to 3389 so the client should be using that from the word go (I know mine do!)...it could be a wierd router thing.
Depending on the exact option(s) you had to change to get it going though, it's making your machine a little more open to the outside world. but maybe not in a huge way....
(so, is it now AnyIP:AnyPort>YourIP:3389 or AnyIp:AnyPort>YourIP:AnyPort? I think forwarding all ports to 3389 would wreck eMule!)
It's probably worth changing the port used from the default though tbh.
Your change it in the PCs registry and add ortno to the end of what you enter into the client.
(so it'd be something like 192.168.0.1:3390, for example)
Then change the rules on the router to match, of course.
'tunes
I have a cisco WAPN610 access point. I have my desktop, google tv, xbox360 and my wdhdtvlive hooked up to it via wireless. I can't get my phone to obtain an ip address from this. I can connect to the router that is connected to my access point, but can't figure out why my phone won't connect. Google told me to try and use only B/G networks, but that didn't work.
Anyone have this same issue, or know of something I can try to fix this?
Thanks in advance!
420fan said:
I have a cisco WAPN610 access point. I have my desktop, google tv, xbox360 and my wdhdtvlive hooked up to it via wireless. I can't get my phone to obtain an ip address from this. I can connect to the router that is connected to my access point, but can't figure out why my phone won't connect. Google told me to try and use only B/G networks, but that didn't work.
Anyone have this same issue, or know of something I can try to fix this?
Thanks in advance!
Click to expand...
Click to collapse
Under wireless networks on your phone does it see the access point? Just won't pick up an IP address??
Are you able to connect your phone to any other wireless networks?? Public Wifi at starbucks or McDonalds or something??
Could either be a bad WPA authentication or faulty wireless radio in your phone if other devices work.
Have you tried forgetting the network under wireless and networks then rebooting the phone just to be sure it's gone then re connect?
jrizk07 said:
Under wireless networks on your phone does it see the access point? Just won't pick up an IP address??
Are you able to connect your phone to any other wireless networks?? Public Wifi at starbucks or McDonalds or something??
Could either be a bad WPA authentication or faulty wireless radio in your phone if other devices work.
Have you tried forgetting the network under wireless and networks then rebooting the phone just to be sure it's gone then re connect?
Click to expand...
Click to collapse
thanks for replying. I can access wifi at work and I can at my friends house. Whenever there is an open connection, it works like a charm, but for whatever reason, when I try to connect at home, it connects, but won't obtain an IP address. I think I can set it up manually and use a static IP. I was doing some googling at work and found something. Very confusing to say the least.
And yes, I have tried to forget it and all that.
thanks again for trying!
how many dhcp leases do you have setup? Depending on how many devices connect, i typically don't setup anymore than 10, but i would try increasing that. What encryption are you using? wpa2/wpa? Is it broadcasting in n or g or is it setup for mixed.
sjpritch25 said:
how many dhcp leases do you have setup? Depending on how many devices connect, i typically don't setup anymore than 10, but i would try increasing that. What encryption are you using? wpa2/wpa? Is it broadcasting in n or g or is it setup for mixed.
Click to expand...
Click to collapse
I'm not sure how many dhcp leases I have set up, but I only have 3 things connecting to the access point. My google TV, Wii, and my desktop. I had it set to broadcast mixed (b,g and N) but changed that to just b/g as another suggested. I am also using wpa2.