Galaxy S4 Mini Duos problem - Help please! - Galaxy S 4 Mini Q&A, Help & Troubleshooting

Hello!
I have a bricked Galaxy S4 Mini Duos GT-I9192. It doesn't turn on anyway. I tried download mode (Home+Volume down+Power on).
I put the debrick.img file on an sd and done as said in the guide.
With the SD in, device turned on, show the messages below:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS
COPY FROM T-FLASH
BOOT RECOVERY
WRITE 139008 sectors
FLASH WRITE FAILURE
ddi: mmc_read failed
ODIN MODE
PRODUCT NAME: GT-I9192
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
CSB-CONFIG-LSB: 0x30
BOOTLOADER AP SWREV: 2
WRITE PROTECTION: Enable
On Odin, when i try to install firmware and pit file, show the errors below:
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin engine v(ID:3.1101)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Odin engine v(ID:3.1101)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Odin engine v(ID:3.1101)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
On device screen show messages below:
MMC: mmc_read fail
ODIN : flash read failure
PIT FAIL : TOTAL SECTORS (0)
Please, can you help me recover this device? Is there any hope and solution? Thanks so much. Best regards.

Please, can anybody help me?!
Enviado de meu XT1225 usando Tapatalk

I'm no expert about bricked phones but I think it's probably your emmc chip that has problem, so probably need a new chip or motherboard (as pit file not working).

marcosgdias said:
Hello!
I have a bricked Galaxy S4 Mini Duos GT-I9192. It doesn't turn on anyway. I tried download mode (Home+Volume down+Power on).
I put the debrick.img file on an sd and done as said in the guide.
With the SD in, device turned on, show the messages below:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS
COPY FROM T-FLASH
BOOT RECOVERY
WRITE 139008 sectors
FLASH WRITE FAILURE
ddi: mmc_read failed
ODIN MODE
PRODUCT NAME: GT-I9192
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
CSB-CONFIG-LSB: 0x30
BOOTLOADER AP SWREV: 2
WRITE PROTECTION: Enable
On Odin, when i try to install firmware and pit file, show the errors below:
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin engine v(ID:3.1101)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Odin engine v(ID:3.1101)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Odin engine v(ID:3.1101)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
On device screen show messages below:
MMC: mmc_read fail
ODIN : flash read failure
PIT FAIL : TOTAL SECTORS (0)
Please, can you help me recover this device? Is there any hope and solution? Thanks so much. Best regards.
Click to expand...
Click to collapse
I'm facing the same problem too. mine happened while playing a game. the game froze and died. was able to get to boot recovery mode using the debrick.img but not the download mode i was expecting to see. i also got the same output from odin except fr the last one which in my case is "flash read failure"... man i really want to fix this unit...

Related

Galaxy S4 i545 Bricked! Help a guy out?

Hey all. Recently i tried to flash stock android to my i545 and it soft bricked on me. I've tried odin numerous times, every version of it I could find, with many different mirrors on the .tar. I've also tried using .pit to no avail. My odin log is as follows for each attempt:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sbl1.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl2.mbn
<ID:0/006> sbl3.mbn
<ID:0/006> rpm.mbn
<ID:0/006> aboot.mbn
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I've also tried kies with no luck due to it never freaking recognizing the device, and yes ive updated the drivers. Ive done all these steps with many different usb's, usb ports, computers, and versions of odin. Is there anything i can do or should i just start looking for a new phone? Help would be greatly appreciated
Make sure that you are flashing the correct Odin for the bootloader you are on download Samsung info and post baseband and bootloader and can point you in the right direction

[Q] "Firmware upgrade encountered an Issue" ODIN PROBLEMS

This was originally posted in the wrong forum. My apologies.
So after following this link: http://www.cnet.com/how-to/how-to-ro...ung-galaxy-s3/ I have a bricked device.
No matter what I do, Odin seems to fail. This is what I think caused the problem in the first place. Also there is the possibility that the guide is way out of date.
So I was wondering if anyone had any advice on how to proceed? The device isnt mine and this isnt my first time rooting a device. I just have never bricked anything before.
Here is the log from ODIN from recreating the process in the link above
Code:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Here is the Log from ODIN from my latest attempt to flash something at it.
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_ATT_I747UCDLK3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried flashing a full image, but it gives this error
Code:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried flashing the "stock" image.
Going to try a different PC tomorrow and hope that I get a different result.
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Do you have an i747 or u747m? Do not flash any more ROMs without knowing the bootloader version installed on your phone. If you phone has a 4.3 or newer bootloader and you try to downgrade it, it will brick your phone.
I recommend that you install the latest version of Philz and flash cm10.2 for the d2att to at least get your phone running so you can determine the bootloader.
audit13 said:
Do you have an i747 or u747m? Do not flash any more ROMs without knowing the bootloader version installed on your phone. If you phone has a 4.3 or newer bootloader and you try to downgrade it, it will brick your phone.
I recommend that you install the latest version of Philz and flash cm10.2 for the d2att to at least get your phone running so you can determine the bootloader.
Click to expand...
Click to collapse
SGH-i747
And the issue I am encountering is a bit bigger than that, I cant install anything. I cant even flash the stock .tar file I found. I cant get ODIN to do anything except fail? I never even got CWM installed.
Can you get into download mode and stay in download mode?
There is not stock tar.md5 ROM you can flash from sammobile because AT&T never made a stock ROM available after 4.1.1.
Did you try to flash Philz Touch for the d2lte in Odin 3.07 using his tar.md5 recovery file? What about TWRP?
No TWRP either?
Can you provide me a link to that MD5
After digging up the MD5 I have got the phone booting again.
Thank you so much for all your help!

[Q] ODIN failed putting in stock rom

Hello,
I recently decided to pull the custom rom my SM-T210R was running and go back into the latest stock image (T210RUEU0COB1_T210RXAC0COB1_XAC). For what ever reason it failed like this:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210RUEU0COB1_T210RXAC0COB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> PBL.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> loke_2nd.bin
<ID:0/006> loke_pxa988.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> __XmitData_Write
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My SM-T210R shows:
ODIN MODE
Product Name: SM-T210R
Current Binary: Samsung Official
System Status: Custom
HW Rev: 0x5
Firmware upgrade encounter an issue. Please select recovery mode in Kies & try again.
Any ideas?
Thanks,
--CP
Ok...I think it was the ROM.
I tried T210RUEU0COB1_T210RXAR0COB1_XAR and it worked. Perhaps the XAR vs XAC thing, though this is from Canada.
CrazyPhil said:
Hello,
I recently decided to pull the custom rom my SM-T210R was running and go back into the latest stock image (T210RUEU0COB1_T210RXAC0COB1_XAC). For what ever reason it failed like this:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210RUEU0COB1_T210RXAC0COB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> PBL.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> loke_2nd.bin
<ID:0/006> loke_pxa988.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> __XmitData_Write
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My SM-T210R shows:
ODIN MODE
Product Name: SM-T210R
Current Binary: Samsung Official
System Status: Custom
HW Rev: 0x5
Firmware upgrade encounter an issue. Please select recovery mode in Kies & try again.
Any ideas?
Thanks,
--CP
Click to expand...
Click to collapse

[Q] help and need some info about gt-19192 unbrick

im new user of samsung my brother mobile once didnt wanna to start the rom then i try the odin to flash it didnt wanna to flash or start rom stuck on battry screeen only no recoery or anthing just download mode and not working to i restart it many times once it open rom and give me update 1 of 2 then it finsh and close and didnt start i flash roms but field i tried to flash recovery but gave me in all <ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery-clockwork-6.0.5.1-serranodsdd.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
but it flash the pit file successful the only file so what can i do ??
if the debrick.img will help me or download another rom or what ?
(im useing original usb of samsung and htc and the drivers updated and my windows win 10 and xp and i use all usb port and odin 3.10.6 1.8 3.7 and Heimdall Suite stuck in the same as odin )
Download Samsung stock firmware from Sammobile.com and flash it through odin 3.09
Go to download mode (vol down + home+ power). Then press vol up
Extract the downloaded zip file, u will get a .tra.md5 file
Add that file to the PDA, it will take few seconds. Repartition and F.Reset time check box should be UNCHECKED.
Then press the start button.
First boot will take some time (25 mins)
Wipe factory data and cache partition.
Sent from my GT-I9195 using XDA Free mobile app
oky im downloading now how to know the witch the stock firmware of my device
Odin mode
product name: gt-i9192
current binary:custom
system kernel: custom
Knox kernel lock: 0x0
Knox warranty void: 0x1
csd-config-lsb: 0x30
boot loader AP swrev: 2
write protection: enable
Click to expand...
Click to collapse
so any one or download any one ?
Shukry Faiz said:
Download Samsung stock firmware from Sammobile.com and flash it through odin 3.09
Go to download mode (vol down + home+ power). Then press vol up
Extract the downloaded zip file, u will get a .tra.md5 file
Add that file to the PDA, it will take few seconds. Repartition and F.Reset time check box should be UNCHECKE
Sent from my GT-I9195 using XDA Free mobile app
Click to expand...
Click to collapse
the same 2 roms
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9192UBUCOC2_I9192ZTRCOC2_I9192UBUCOC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Removed!!
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
likenoother94 said:
the same 2 roms
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9192UBUCOC2_I9192ZTRCOC2_I9192UBUCOC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Removed!!
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
First Reboot to Recovery and Wipe Data/Factory Reset, Wipe Cache and Dalvik Cache
then install rom through Odin
then all threads will be succeeded.
likenoother94 said:
the same 2 roms
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try to flash latest version of KitKat . I think u try to flash an older version on your phone that is why it fails at aboot ( bootloader )
SilviuMik said:
Try to flash latest version of KitKat . I think u try to flash an older version on your phone that is why it fails at aboot ( bootloader )
Click to expand...
Click to collapse
that's the 2 roms i download them from sammobile.com
I9192XXUBNB1_I9192OJVBNB1_EGY
I9192UBUCOC2_I9192ZTRCOC2_ZTR
if it not the right can u give me
the link of the rom :crying:
it stuck in recovery or boot loader or anything but the pit file alone goes succeed
likenoother94 said:
that's the 2 roms i download them from sammobile.com
I9192XXUBNB1_I9192OJVBNB1_EGY
I9192UBUCOC2_I9192ZTRCOC2_ZTR
if it not the right can u give me
the link of the rom :crying:
Click to expand...
Click to collapse
With COC it should have worked . I`m sorry no idea other then phone repair
SilviuMik said:
With COC it should have worked . I`m sorry no idea other then phone repair
Click to expand...
Click to collapse
dont have recovery ?? :crying: all i have odin mode @sajid0786
likenoother94 said:
dont have recovery ?? :crying: all i have odin mode @sajid0786
Click to expand...
Click to collapse
See these links if these help you
Check This
Check This
sajid0786 said:
See these links if these help you
Check This
Check This
Click to expand...
Click to collapse
nothing thankx for help :crying:

HELP SM-G530FZ stuck on loading screen

Hi folks....
My mom's phone (SM-G530FZ) is stuck on the loading screen.
From what i've been told, the phone was charging when suddently the screen went "white" and automatically restarted.
From that moment, it does not start anymore and it's stuck on the loading screen (samsun logo etc).
I can enter the download mode, so i've tried to flash the original firmware (G530FZXXS1BPL1_G530FZITV1BPF1_G530FZXXU1BPI1_HOME.tar...one binary) with Odin with no luck, obtaining the following error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I've then tried to download another firmware (G530FZXXU1ANL7_OXX1ANL4_v4.4.4_Repair_Firmware with BL+AP+CP+CSC+PIT) ...no luck again
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried also with different Odin's versions
Any idea on what might have happened and whether or not there is a way to fix it?
Thanks
Anybody?

Categories

Resources