Need help Samsung Tab 3 T210R Stuck in Samsung Loop - Galaxy Tab 3 Q&A, Help & Troubleshooting

I am no expert like some of you in the community and I am not novice, I've rooted/installed Roms/ unbricked devices before. I purchased a Samsung Tab 3 T210R that was stuck in the Samsung loop. Upon receiving the Tab 3 I reset to default and wipe cache, it then restated and took me to the set up process if the device (like logging into my Samsung acct, setting up date/time) but it would freeze through the process. So, I then I followed everything stated in this thread http://forum.xda-developers.com/showthread.php?t=2459734 ..after following the steps in the thread I got a "kernel panic" message. I followed the task a second & third time using the first two links in Sammobile (Canada and Cellular South), the device now stays in the Samsung loop and sometimes shows a pixelated/ distorted Samsung logo.
Since I bought the device on eBay "as-is", I don't know what Android version was installed, but from the looks of it, it may have been a stock rom. I do know the model number is T210R 8 GB WiFi. I hope you guys can guide me and explain how to fix this issue. I would truly appreciate your help!
I forgot to mention after rebooting it to wipe cache/reset there's a message in red that reads " E: failed to verify whole-file"
Thanks in advance!

Related

[Q] Note 2- n7100zsllb1 showing 'unknown' iemi and baseband

Hello genius developers,
Need your help as i am stuck with as issue in my note 2 and tried all shops in my nearby location to fix it. The story of issue goes like as below:
I bought my note 2 from USA(un locked) and started using it in India. It was working good until the day i decided to upgrade it to 4.4.2 from its original version 4.1.2. I installed Odin and the firmware from this forum and tried updating it but end up with error in writing (NAND writing got failed). Due to this device was not booting properly and getting into boot loop. I went to gray market to get it fixed and after all his efforts he installed 4.4.2 on to the device n7100xxufnd3 on my device but it turned basedband and iemi as 'unknown'. hence SIM is not recognized by my device.
Samsung Kites is not recognizing my device and it is also not rooted (verified with aap). If anyone can help me providing set by step procedure to fix this issue it will be great help. Screenshots of the device status is attached. Open for donation

[Q] Galaxy Tab S "Bricked"? after installing customer rom

Hello Guys,
Need your help.
I have flashed hundreds of roms on my android phones and tablets, but this time something new happened to me:
After installing a t700 Rom using twrp recovery, my tablet got stuck at boot logo, doesn't matter how many resets i try, it never goes beyond the black and whit samsung boot logo!
I have tried to reset using kies, flashed a stock firmware with Odin, etc ect ect, nothing! its still stuck at boot logo.
One curious thing happened, after flashing sock firmwares for the second or third time, the Samsung sounds stops halfway, and then it goes back to the Samsung logo.
Any ideas on how to get out of this nightmare?
Thank you!!
Hi
Thanks for writing to us at XDA Assist. Please standby while we have your thread/question moved to the appropriate sub-forum for your device.
For future reference you can find your device sub-forum here (bookmark/subscribe this):
Samsung Galaxy Tab S
Within that section you will find a dedicated q&a sub-forum (this is where your thread is going to be moved to):
Galaxy Tab S Q&A, Help & Troubleshooting
Good luck!
black_coder said:
Hello Guys,
Need your help.
I have flashed hundreds of roms on my android phones and tablets, but this time something new happened to me:
After installing a t700 Rom using twrp recovery, my tablet got stuck at boot logo, doesn't matter how many resets i try, it never goes beyond the black and whit samsung boot logo!
I have tried to reset using kies, flashed a stock firmware with Odin, etc ect ect, nothing! its still stuck at boot logo.
One curious thing happened, after flashing sock firmwares for the second or third time, the Samsung sounds stops halfway, and then it goes back to the Samsung logo.
Any ideas on how to get out of this nightmare?
Thank you!!
Click to expand...
Click to collapse
1. Load up your PC the original stock firmware, which corresponds to your Tab original Region CSC-code according to the model number and serial number of your Tab. How it may be defined, you can read in this thread:
http://forum.xda-developers.com/galaxy-tab-s/help/how-to-select-correct-firmware-tablet-t3016068/post58500430
2. Flash your Tab by Odin c original stock firmware from p.1
Regards
I have seen this before when a tablet gets stuck on the Samsung logo, what you need to do is after flashing your stock firmware using odin, you then need to get into stock recovery and wipe cache and factory reset from within stock recovery and then reboot.

[Firmware] Unbrick & restore Galaxy Tab 3 7in SM-T210 wifi

Hi,
In my samsung galaxy SM-T210 i have an issue while installing custom rom or official rom after installation i get an error message saying "unable to mount 'efs " error. I did clear all data, catche,system and dalv but also i continue getting same error. After the installation when i power on my device it does not go forward after samsung logo it continues in this window. I waited more than hours but it did not start it keeps on glowing samsung logo. Please help me correct the isssue with every details possible.

Can't get pass setup wizard message keep flashing.

Samsung Galaxy tab pro T520
Amateur at routing I tried rooting it then flashed it and I can't get past the setup wizard message that keeps flashing after I rebooted the device and everytime I reboot it Android is dead can someone please help

Samsung GT-I9192 starts and shutdown after its Logo and again starts and so on...

Hello Everyone,
This is my first thread on this forum, which i am making because I ran out of options, and don't know what to do....
My Samsung Galaxy S4 mini(GT-I9192) were shut down automatically when i am using it.After then I started my phone again
it starts normally but after the details Samsung Galaxy S4 mini(GT-I9192)comes and it again turn off and again restarts and
this process is going again and again.As I tell you my phone doesn't stuck on a boot as my phone restarts again before the samsung logo comes.
I've tried Emergency firmware upgrade and Initialization through kies but after entering model no. and S/N,
It says 'GT-I9192' does not support initialization. I've done that before with kies it never gives that error I don't know why now.
After That I tried to install stock firmware by Odin in download mode, The process gets completed pass message comes after that my phone reboots in recovery mode and a message print on the bottom "did not match size '/system/csc/common/system/csc/others.xml' (no data available)" i don't know what is that for and after that i reboot my phone and still same thing...
After all that I think maybe its an hardware issue but if it is an hardware issue then how my phone starts and again shutdown so i don't think it's an hardware issue btw i don't know what it is.
So Please If anyone Have any Solution please help me.
Thank You
I have same problem on my galaxy s4 mini gt-i9195 LTE.
first the phone doesnt wanna turn on at all, just show as QHSUSB_DLOAD
after xx hours googling for solution i try unbrick.img which bring the screen back in live:good:
then i try several roms but the phone reject the flash, so i try flash with original stock rom, that went successful
but that doesnt change something, still keep rebooting, even when load recovery it get reboot and keep rebooting.
I don't think that this might be a hardware issue, but something wrong with the android partitions.
I'll keep playing with it hope i find some solution.
If someone read this and has same or similar issue, please post what you have try so far, so we can work on it and find the problem.:highfive:
Thanks for your reply...
As my phone were start after flashing so many times and now it says Device Memory Corrupted Please reset your device to default
settings and there is a reset tab which doesn't working when i keep pressing that so now i think that maybe my eMMC chip was damaged well exactly i don't know that yet....
well for you just try connecting through kies and do a firmware upgrade and if that doesn't working than flash it through odin and also download PIT file for re-partition....

Categories

Resources