*This guide is for getting back alive a phone from soft brick issue/Boot loop*
*Note: I am not responsible for any kind of damage to your phone.*
*Because whatever is done, is done by you*
*Read the guide totally before flashing*
*Just follow the instructions properly*
Firstly download & extract MT6582 USB VCOM drivers from the internet
Get the zip of flashing tool & firmware from here
https://docs.google.com/uc?id=0B3zai8xX-XsycnNGUmpMUkNjcmc (Don't own this link )
Now you are ready move on for the upcoming process.
1. Now Extract the Lenovo_S660_ROW_S062_141126_(by_xdafirmware.com).zip
2. Then go into the extracted folder and open the Sp flash tool folder.
3. Then open flash_tool.exe from it.
4. Select scatter loading
5. Go inside the extracted folder and go inside the Firmware folder and select MT6582_Android_scatter.txt
6. Now you will see all files loaded.
Be sure you have selected the download only option, never use others!! , if you face a problem tell me
7. As you select the scatter text the software gets all the necessary files that are needed for flashing, it’s because they are in the same folder, so now we can directly continue towards main flashing.
Main flashing
1. Make sure your usb cable is ok.
2. (Confirmation) this guide is for softbrick phones.
Now when you are totally ready.
1. Remove the battery of the phone.
2. now try connecting the phone without battery, keep the device manager open, and the connect the cable to the phone, if you see installing usbvcom driver you are good to go, if you didn't see anything then try with (battery) mostly in my case it was without battery.
i am unsure. please check it. it won't harm your phone, but don't try while flashing try it before flashing. Don't try anything while flashing!!, once you find the method, your computer will be installing driver.(keep the device manager open for better understanding. (if you are still unsure of something, don't start flashing) Ask me anything on facebook - for instant response.
3. once you have installed the driver, and ready to move on.
4. Then click the download button on the software flash tool.
5. Now in seconds it will load files and it will wait for your phone to connect, it will show searching.
7. So now its time for flashing.
Now connect the phone with usb cable(without battery/with battery you have to find out before flashing), it will start flashing, do not make any mistake of removing cable, or else it may hard brick your phone, the download will start if there are no other issues, and total flashing time would be 6 or 10 minutes.
If the flashing went all ok, with no problems then it will show Download Ok.(message Box)
8. Now finally after flashing is 100% done and see download ok, disconnect the phone from the usb cable and remove and re-insert the battery, and power it on, Happy Flashing :angel:
Guide By Naineesh Rathod
www.facebook.com/naineeshvrathod
XDA Name - NaineeshPlease hit thanks if it helped
I m facing bootloop on s660 maine nav.bar build prop ki tweak se build.prop main edit karke nav.bar enble kia tha then now voh muje nikal na tha to maine build.prop main jo line edit ki thi voh maine vaha se delet kar di then reboot kia fir bhi nav.bar nikla nahi isliye maine frnds se pucha usne bol build.prop hain tere pass uka backup maine bola ha hain to us ne bola es file expl se usko vaha pe laga to maine copy past kia the 3 ops maine overwirte pe click kia then after phone reboot kia to now bootloop ho raha hain plz help me out
Related
Hii all,
actually this my first post in the forum and i hope to find the solution to my small prob.
The problem is appearance some words on the jasjar screen like "usb" n "serial"
they doesn't disappear although i 'v done "reset" n "Power+reset+backlight"
They are permanently appear on the screen and make my jasjar as dead ..
----
actually i've open the rom upgrade icon from the mobile directly and i didn't use the pc at all because i didn't know how to upgrade it
----
please if someone know the solution of this prob. tell me >>
n i want to know how to upgrade the rom if i already downloaded it >>
Welcome to forums
have a read on my signature link and check for usb connection
Moving to upgrade section
Please orb or anyone can help >> ):
I want the software of the jasjar which come with the installtion cd ..
I tried to join the jasjar with the pc but there's a problem with the usb ..
Plese help me as my mobile now like dead body
Thanks In Advance ;
Hello,
First instal ActiveSync 4.5 in PC. - if not already installed
Code:
http://www.softwarepatch.com/windows/activesync.html
Then in settings in (ActiveSync) disable (NOT check): "allowed to connect to one of the following port" and "Allow connection to USB".
Perhaps the translation is correct. I use the CZ version. But it's second and third check box.
Now
This works for when the Universal is in Bootloader and Windows Mobile.
1. First download the ROM you want to install.
2. Extract it to a folder (use winar or other extraction software).
3. There will be up to 3 ROMs in the package: ms_.nbf (Extended ROM), nk.nbf (OS ROM), radio_.nbf (Radio ROM)
4. Delete those which you don't want to install. (If you just want to upgrade the radio rom for instance delete ms_.nbf and nk.nbf and leave radio_.nbf.)
5. Download UniversalRUU.zip
6. Extract it and copy into that folder the nbf files you want to install.
7. Enter BootLoader mode by pressing and holding the power button and backlight button whilst performing a reset with the stylus. And plug to PC. Wait few seconds.
8. Doubleclick ROMUpgradeUt.exe and follow the instructions
9. When the upgrade is finished pull out the USB cable from the Universal.
10. You will need to do a soft reset OR hard reset depending on the situation. (note: some say do a soft reset / others a hard reset .. possibly someone with more knowledge could correct me here, but until then it's best to investigate the matter for yourself on the forum.)
11. To do a hard reset (push the two menu buttons ("-") on the keyboard + the reset button at the same time (all of this three). Doing a hard reset will result in you losing all your installed apps and data so ensure you have a backup of everything first.) Everything should be fine from this time. You have to calibrate the screen and do some tutorial...
12. If after doing a hard reset you want your Universal not to install the extras from the Extended ROM wait untilsetup is complete and then do a softreset when the popup window appears (you have 3 seconds before it installs ExtendedROM)
For a long time I have not installed the new ROM. I remember so I proceeded as follows
Greetings
Svobi
Really I don't know how to thank u
Thread closed as problem got solved
I don't see why all this faffing about with proxy grabbers and URL guessing in necessary to get the correct firmware file for your LG phone, there is an easier way...
1. Go to the LG website and find your phone, download the USB drivers and mobile support tool.
2. Install the USB drivers, remove the battery from your phone and note the model number, serial number and IMEI number then replace the battery.
3. Turn on your phone and plug in your USB to the computer and phone and wait for the drivers to install.
4. Click your 'start menu' and select 'Computer', click the 'Tools' menu at the top left of the screen and select 'Folder Options' and then the 'View' tab, put the radio dot in the 'Show hidden files, folders or drives', also remove the check-mark from 'Hide extensions for known file types' and click 'Apply' then 'OK'.
5. Run the mobile support tool 'exe or setup' file, select the emergency firmware recovery thingy and enter your phones I.D from earlier
When the mobile support tool finds your firmware download, click to download it.
6. Immediatly navigate to 'C:\ProgramData\LGMOBILEAX\Phone\' where you will find your firmware file in the process of downloading (mine was called 'V10A_00.kdz').
7. Keep an eye on the mobile support tool to see when the download is going to complete, before it does right click on the white background of the 'C:\ProgramData\LGMOBILEAX\Phone\' folder and select 'Refresh' to update the firmware files downloaded file size - ideally do this several times during the download process to allow Windows to calculate the file size faster at the end and produce a useable '.KDZ' firmware file before the mobile support tool get's too far into the process of extracting it.
8. Once the mobile support tool changes from the downloading screen to the flashing part grab your firmware file and drag it to the desktop or any other location to copy it, you only have a small amount of time to do this before the mobile support tool extracts the files and deletes the '.KDZ' file so don't worry about scratching your arse just yet!
Just a note, I also copied the extracted '.CAB' file and 'DIAGCommand.xml' files for no real reason!
9. Once Windows has copied it and the 'File Copy' box closes YANK THE USB LEAD OUT OF YOUR PHONE!
If for any reason your computer takes longer than 10 seconds after the download finishes to copy the file then pull your USB lead if you don't want the phone updated and go buy yourself a decent computer!
If you wait any longer than 10 seconds after the download completes you may well brick your phone which I'd like to add I accept NO responsibility for, not even if you follow my method to the letter and still end up bricking your phone I promise you I won't lose a moments sleep over it!
What I can tell you is that the 10 seconds time frame I give is an over safe time frame. In reality your phone will not start to flash any data until it reboots so I suggest having the volume turned up to listen for the USB disconnect / reconnect sound. At the very latest remove the USB cable after the disconnect sound but if you hear the reconnect and the cable is still attached you have 2 choices, 1: Do nothing and have an updated mobile phone or 2: Pull out the USB cable and have no phone. YOU HAVE BEEN WARNED!
Hope this helps you. Please 'Thank Me' if it does.
sparkyuiop
P.S. You may now want to go back to your Computer/ Tools/ View folder and set them back to default.
thanx
sparkyuiop said:
I don't see why all this faffing about with proxy grabbers and URL guessing in necessary to get the correct firmware file for your LG phone, there is an easier way...
1. Go to the LG website and find your phone, download the USB drivers and mobile support tool.
2. Install the USB drivers, remove the battery from your phone and note the model number, serial number and IMEI number then replace the battery.
3. Turn on your phone and plug in your USB to the computer and phone and wait for the drivers to install.
4. Click your 'start menu' and select 'Computer', click the 'Tools' menu at the top left of the screen and select 'Folder Options' and then the 'View' tab, put the radio dot in the 'Show hidden files, folders or drives', also remove the check-mark from 'Hide extensions for known file types' and click 'Apply' then 'OK'.
5. Run the mobile support tool 'exe or setup' file, select the emergency firmware recovery thingy and enter your phones I.D from earlier
When the mobile support tool finds your firmware download, click to download it.
6. Immediatly navigate to 'C:\ProgramData\LGMOBILEAX\Phone\' where you will find your firmware file in the process of downloading (mine was called 'V10A_00.kdz').
7. Keep an eye on the mobile support tool to see when the download is going to complete, before it does right click on the white background of the 'C:\ProgramData\LGMOBILEAX\Phone\' folder and select 'Refresh' to update the firmware files downloaded file size - ideally do this several times during the download process to allow Windows to calculate the file size faster at the end and produce a useable '.KDZ' firmware file before the mobile support tool get's too far into the process of extracting it.
8. Once the mobile support tool changes from the downloading screen to the flashing part grab your firmware file and drag it to the desktop or any other location to copy it, you only have a small amount of time to do this before the mobile support tool extracts the files and deletes the '.KDZ' file so don't worry about scratching your arse just yet!
Just a note, I also copied the extracted '.CAB' file and 'DIAGCommand.xml' files for no real reason!
9. Once Windows has copied it and the 'File Copy' box closes YANK THE USB LEAD OUT OF YOUR PHONE!
If for any reason your computer takes longer than 10 seconds after the download finishes to copy the file then pull your USB lead if you don't want the phone updated and go buy yourself a decent computer!
If you wait any longer than 10 seconds after the download completes you may well brick your phone which I'd like to add I accept NO responsibility for, not even if you follow my method to the letter and still end up bricking your phone I promise you I won't lose a moments sleep over it!
What I can tell you is that the 10 seconds time frame I give is an over safe time frame. In reality your phone will not start to flash any data until it reboots so I suggest having the volume turned up to listen for the USB disconnect / reconnect sound. At the very latest remove the USB cable after the disconnect sound but if you hear the reconnect and the cable is still attached you have 2 choices, 1: Do nothing and have an updated mobile phone or 2: Pull out the USB cable and have no phone. YOU HAVE BEEN WARNED!
Hope this helps you. Please 'Thank Me' if it does.
sparkyuiop
P.S. You may now want to go back to your Computer/ Tools/ View folder and set them back to default.
Click to expand...
Click to collapse
for me the lg support tool extracted the files was too late i only searched for ur method later but am still able to see F320S10K_00.kdz file and the size of this file is 2.07gb
Has anyone been able to grab f500l kdz?
sparkyuiop said:
I don't see why all this faffing about with proxy grabbers and URL guessing in necessary to get the correct firmware file for your LG phone...
If you wait any longer than 10 seconds after the download completes you may well brick your phone which I'd like to add I accept NO responsibility for, not even if you follow my method to the letter and still end up bricking your phone I promise you I won't lose a moments sleep over it!
YOU HAVE BEEN WARNED!
Click to expand...
Click to collapse
Ahh, guess those are VERY good reasons to use proxys and url sniffers after all, less tragedy
LGBridge + Fiddler = Wonders
sparkyuiop said:
I don't see why all this faffing about with proxy grabbers and URL guessing in necessary to get the correct firmware file for your LG phone, there is an easier way...
1. Go to the LG website and find your phone, download the USB drivers and mobile support tool.
2. Install the USB drivers, remove the battery from your phone and note the model number, serial number and IMEI number then replace the battery.
3. Turn on your phone and plug in your USB to the computer and phone and wait for the drivers to install.
4. Click your 'start menu' and select 'Computer', click the 'Tools' menu at the top left of the screen and select 'Folder Options' and then the 'View' tab, put the radio dot in the 'Show hidden files, folders or drives', also remove the check-mark from 'Hide extensions for known file types' and click 'Apply' then 'OK'.
5. Run the mobile support tool 'exe or setup' file, select the emergency firmware recovery thingy and enter your phones I.D from earlier
When the mobile support tool finds your firmware download, click to download it.
6. Immediatly navigate to 'C:\ProgramData\LGMOBILEAX\Phone\' where you will find your firmware file in the process of downloading (mine was called 'V10A_00.kdz').
7. Keep an eye on the mobile support tool to see when the download is going to complete, before it does right click on the white background of the 'C:\ProgramData\LGMOBILEAX\Phone\' folder and select 'Refresh' to update the firmware files downloaded file size - ideally do this several times during the download process to allow Windows to calculate the file size faster at the end and produce a useable '.KDZ' firmware file before the mobile support tool get's too far into the process of extracting it.
8. Once the mobile support tool changes from the downloading screen to the flashing part grab your firmware file and drag it to the desktop or any other location to copy it, you only have a small amount of time to do this before the mobile support tool extracts the files and deletes the '.KDZ' file so don't worry about scratching your arse just yet!
Just a note, I also copied the extracted '.CAB' file and 'DIAGCommand.xml' files for no real reason!
9. Once Windows has copied it and the 'File Copy' box closes YANK THE USB LEAD OUT OF YOUR PHONE!
If for any reason your computer takes longer than 10 seconds after the download finishes to copy the file then pull your USB lead if you don't want the phone updated and go buy yourself a decent computer!
If you wait any longer than 10 seconds after the download completes you may well brick your phone which I'd like to add I accept NO responsibility for, not even if you follow my method to the letter and still end up bricking your phone I promise you I won't lose a moments sleep over it!
What I can tell you is that the 10 seconds time frame I give is an over safe time frame. In reality your phone will not start to flash any data until it reboots so I suggest having the volume turned up to listen for the USB disconnect / reconnect sound. At the very latest remove the USB cable after the disconnect sound but if you hear the reconnect and the cable is still attached you have 2 choices, 1: Do nothing and have an updated mobile phone or 2: Pull out the USB cable and have no phone. YOU HAVE BEEN WARNED!
Hope this helps you. Please 'Thank Me' if it does.
sparkyuiop
P.S. You may now want to go back to your Computer/ Tools/ View folder and set them back to default.
Click to expand...
Click to collapse
First off im sorry for quoting op. Im try said method to get a kdz thats not released. As soon as im using old mobile support tool btw. But as soon as dl hits 100 tool attempts to extract it and imeaditly deletes its no 10 seconds. Literally like 1/2 second the goes to error. Long story short. I got a old lg vista frp locked and no available method to bypass i was gonna attempt to update it to a newer firmware to see if ne of the methods work there. The phone was released with kk and not really a antirollback protection. But theres a speci proced to downgrade and i figured if i could get back kk no frp
the method seems to work, so thank you for this solution, i tried a few times until I made it happen, the thing with this is that you can only get recent updates, and in my case I'm looking for an older version of the firmware. hope your post will be usefull to other. thank you.
LG OS downloads
Hey guys, LG has a site for their phone OS's, as well as other devices, DLs... Just Google LG OpenSource Code Distribution. Hope this helps.
Windows 7 ...Not sure if it works with Windows 8. Test and inform me please ZV7
Red_Kamel said:
12. For S/W browse to "LG G2 Stock" Folder and select LS980ZV7_01.tot file
Click to expand...
Click to collapse
If you can get into download mode by holding Vol Up and then connecting a USB cable (while the device is off) then this method will work for you.
http://www.rwilco12.com/forum/showthread.php?tid=96
Thank you @rwilco12 for hosting the download
1. Download the above Zip and extract it to a folder on your Desktop called "LG G2 Stock" (or whatever you prefer to name it).
2. Install LGUnitedMobileDriver from "LG G2 Stock" Folder
3. Install Setup_LGFlashTool from "LG G2 Stock" Folder (You will get a log in error if you try to open it)
4. Extract MegaLock.zip from the "LG G2 Stock" Folder to C:\LG\LGFlashTool and overwrite existing MegaLock.dll file. This gets around the Log in Error you got before when you tried to open it.
6. Put phone in Download mode by holding Volume up for a couple seconds and then plugging the phone in via USB.
7. Go to Windows Start Menu and under "search programs and files" type "device manager" and open it up.
8. Go to Ports (COM & LPT). You should see LGE AndroidNet etc... Right click it and go to Properties > Port Settings > Advanced > Change COM Port Number to COM41 > OK > OK > Close Device Manager
9. You should have a LGFlashTool shortcut on your desktop. Double Click it to open it up.
10. In the Model Config that opens up Select Manual Mode in top left.
11. For DLL browse to "LG G2 Stock" folder and select LGLS980_20130904_LGFLASHv151.dll file
12. For S/W browse to "LG G2 Stock" Folder and select LS980ZV7_01.tot file
13. Hit OK and then click the Yellow Arrow in top left of LG Flash Tool. Wait for it to say "READY!!"
14. Unplug your phone and power it off (it may reboot before you can power it off).
15. Go back into download mode and the stock ROM will start flashing on it's own. It should take no more than 10 minutes. It may stop around 80% but your phone will say 100% and reboot and Presto! Back to stock or unbricked! (Whichever you were trying to do)
:good:
Thanks and I hope this helps!
Woohoo!! Lol you my dude, just saved my backside,lol....GREAT JOB!!!!!!Many Thanks...
You, my dude, are welcome
Red_Kamel said:
If you can get into download mode by holding Vol Up and then connecting a USB cable (while the device is off) then this method will work for you.
EDIT: Link Temporarily Down. I will have it back up tonight on a better server
NEW LINK TO COME SOON
1. Download the above Zip and extract it to a folder on your Desktop called "LG G2 Stock" (or whatever you prefer to name it).
2. Install LGUnitedMobileDriver from "LG G2 Stock" Folder
3. Install Setup_LGFlashTool from "LG G2 Stock" Folder (You will get a log in error if you try to open it)
4. Extract MegaLock.zip from the "LG G2 Stock" Folder to C:\LG\LGFlashTool and overwrite existing MegaLock.dll file. This gets around the Log in Error you got before when you tried to open it.
6. Put phone in Download mode by holding Volume up for a couple seconds and then plugging the phone in via USB.
7. Go to Windows Start Menu and under "search programs and files" type "device manager" and open it up.
8. Go to Ports (COM & LPT). You should see LGE AndroidNet etc... Right click it and go to Properties > Port Settings > Advanced > Change COM Port Number to COM41 > OK > OK > Close Device Manager
9. You should have a LGFlashTool shortcut on your desktop. Double Click it to open it up.
10. In the Model Config that opens up Select Manual Mode in top left.
11. For DLL browse to "LG G2 Stock" folder and select LGLS980_20130904_LGFLASHv151.dll file
12. For S/W browse to "LG G2 Stock" Folder and select LS980ZV7_01.tot file
13. Hit OK and then click the Yellow Arrow in top left of LG Flash Tool. Wait for it to say "READY!!"
14. Unplug your phone and power it off (it may reboot before you can power it off).
15. Go back into download mode and the stock ROM will start flashing on it's own. It should take no more than 10 minutes. It may stop around 80% but your phone will say 100% and reboot and Presto! Back to stock or unbricked! (Whichever you were trying to do)
:good:
Thanks and I hope this helps!
Click to expand...
Click to collapse
G1_enthusiast said:
install the driver on your computer again and try ADB...
if not...gluck man I dont think there is another way.
Click to expand...
Click to collapse
I brricked my phone LG G2 Sprint and now i am in trouble ...phone not booting..
only i get the sideload via Recovery mode...
need a Recovery TWRP/CWM any...
and the way to flash the Recovery...
as i have changed the build.prop's setting
ro.build.target_operators= SPR
to
ro.build.target_operators= OPEN
and restarted it and then ..the ENd.
phone not starting...
tried to use LG Flash TOOL the .dll and .tot downloaded of Sprint
but the error comes for dll as i have changed build.prop to OPEN
so that LG FLASH TOOL is also not working..
figured out the solution but the way for these solution is still far...
just need the WAY for the solution..
Solution : Need to Replace the build.prop(OPEN) which is edited ONE ----> to-----> Original build.prop(SPR) [so that can use your said procedure]
if can't replace then should be able to edit the OPEN to SPR again
Only the things can work thru SIDELOAD only.
Also need a way to flash the Recovery in LG G2 SPRINT (so as to push or edit the build.prop) that to via SIDELOAD
The WAY : ? ? ? ? ? ? ?
?? ? ? ?? ? ?
(It's Really a Milky Way) {UNSEEN}
Please Help.
http://forum.xda-developers.com/showthread.php?t=2641831&page=2
See this thread post #18. It may help fix your problem.
Maybe go to Help and Troubleshooting http://forum.xda-developers.com/lg-g2/help
RK
Nice work my friend! Thanks!
Sent from my SPH-L900 using Tapatalk
Please help me
Red_Kamel said:
If you can get into download mode by holding Vol Up and then connecting a USB cable (while the device is off) then this method will work for you.
http://www.rwilco12.com/forum/showthread.php?tid=96
Thank you @rwilco12 for hosting the download
1. Download the above Zip and extract it to a folder on your Desktop called "LG G2 Stock" (or whatever you prefer to name it).
2. Install LGUnitedMobileDriver from "LG G2 Stock" Folder
3. Install Setup_LGFlashTool from "LG G2 Stock" Folder (You will get a log in error if you try to open it)
4. Extract MegaLock.zip from the "LG G2 Stock" Folder to C:\LG\LGFlashTool and overwrite existing MegaLock.dll file. This gets around the Log in Error you got before when you tried to open it.
6. Put phone in Download mode by holding Volume up for a couple seconds and then plugging the phone in via USB.
7. Go to Windows Start Menu and under "search programs and files" type "device manager" and open it up.
8. Go to Ports (COM & LPT). You should see LGE AndroidNet etc... Right click it and go to Properties > Port Settings > Advanced > Change COM Port Number to COM41 > OK > OK > Close Device Manager
9. You should have a LGFlashTool shortcut on your desktop. Double Click it to open it up.
10. In the Model Config that opens up Select Manual Mode in top left.
11. For DLL browse to "LG G2 Stock" folder and select LGLS980_20130904_LGFLASHv151.dll file
12. For S/W browse to "LG G2 Stock" Folder and select LS980ZV7_01.tot file
13. Hit OK and then click the Yellow Arrow in top left of LG Flash Tool. Wait for it to say "READY!!"
14. Unplug your phone and power it off (it may reboot before you can power it off).
15. Go back into download mode and the stock ROM will start flashing on it's own. It should take no more than 10 minutes. It may stop around 80% but your phone will say 100% and reboot and Presto! Back to stock or unbricked! (Whichever you were trying to do)
:good:
Thanks and I hope this helps!
Click to expand...
Click to collapse
he e
Hello...id been looking for help since two days Reading and following ecery steps with no luck i have the exact problema. I follow your guide but i get fail CroosDL Device Model different or something like that it shows that the model and the firmware im tryng to flash are differents. I also find in this section a thread where someone posted a dll file to use as a combo whith sprint tot file and i got the same results. I also tried back to stock using lg suppor tool but it get stock on donwloading firmware,
I was trying to get into fastboot to flash twrp image and slideload but i cant , found a thread saying is preesing vol + while plugging usb but like that i just get into download mode again. My phone keep rebooting. Thanks for any help.:crying:
ToledoG28 said:
he e
Hello...id been looking for...
Click to expand...
Click to collapse
See post number #5 above. Thre is a link to a thread that might adress your issue. What model does LG Flash tool think your phone is?
Red_Kamel said:
See post number #5 above. Thre is a link to a thread that might adress your issue. What model does LG Flash tool think your phone is?
Click to expand...
Click to collapse
tmo d801
ToledoG28 said:
tmo d801
Click to expand...
Click to collapse
The guy in the thread I posted above I believe had thexact same problem. I think the fix is post #18
[email protected] said:
I brricked my phone LG G2 Sprint and now i am in trouble ...phone not booting..
only i get the sideload via Recovery mode...
need a Recovery TWRP/CWM any...
and the way to flash the Recovery...
as i have changed the build.prop's setting
ro.build.target_operators= SPR
to
ro.build.target_operators= OPEN
and restarted it and then ..the ENd.
phone not starting...
tried to use LG Flash TOOL the .dll and .tot downloaded of Sprint
but the error comes for dll as i have changed build.prop to OPEN
so that LG FLASH TOOL is also not working..
figured out the solution but the way for these solution is still far...
just need the WAY for the solution..
Solution : Need to Replace the build.prop(OPEN) which is edited ONE ----> to-----> Original build.prop(SPR) [so that can use your said procedure]
if can't replace then should be able to edit the OPEN to SPR again
Only the things can work thru SIDELOAD only.
Also need a way to flash the Recovery in LG G2 SPRINT (so as to push or edit the build.prop) that to via SIDELOAD
The WAY : ? ? ? ? ? ? ?
?? ? ? ?? ? ?
(It's Really a Milky Way) {UNSEEN}
Please Help.
Click to expand...
Click to collapse
I had about the same problem, restored the appliance in the following way:
Turn off the device completely
Press the Vol+ and the power and opens in Factory Hard Reset process. push the power button twice to accept to start the process.
Restarted the device and opens in any situation.
Close the device completely.
Press Vol+ and you connect the USB cable and opens the device in Download mode-Firmware Update
Expect to finish installing the drivers on the computer.
do right click on my computer icon, choose Properties and Device Management choose the COM/LPT Ports there you will see your device to be attached to some COMx selects and do again properties-settings-Advanced-Port port number the change by COMx in COM41, press Ok and close all Windows.
Run the LGFlashTools program you choose the LGLS980_20130904_LGFLASHv151.dll and LS980ZV8_13.51097.tot, in Action Mode you choose UPGRADE DL and USB Connection Mode you choose.
from the icons you click the icon and choose serial is checked, all OK and close the window, then hit the yellow arrow and wait to complete control of files when your completed written ready.
Un-plug the USB from device to start the flash update process
Stock FIrmware
dll file
I wish to be helped
MakisPgr said:
I had about the same problem, restored the appliance in the following way:
Turn off the device completely
Press the Vol+ and the power and opens in Factory Hard Reset process. push the power button twice to accept to start the process.
Restarted the device and opens in any situation.
Close the device completely.
Press Vol+ and you connect the USB cable and opens the device in Download mode-Firmware Update
Expect to finish installing the drivers on the computer.
do right click on my computer icon, choose Properties and Device Management choose the COM/LPT Ports there you will see your device to be attached to some COMx selects and do again properties-settings-Advanced-Port port number the change by COMx in COM41, press Ok and close all Windows.
Run the LGFlashTools program you choose the LGLS980_20130904_LGFLASHv151.dll and LS980ZV8_13.51097.tot, in Action Mode you choose UPGRADE DL and USB Connection Mode you choose.
from the icons you click the icon and choose serial is checked, all OK and close the window, then hit the yellow arrow and wait to complete control of files when your completed written ready.
Un-plug the USB from device to start the flash update process
Stock FIrmware
dll file
I wish to be helped
Click to expand...
Click to collapse
Those files are already in the OP. Also those instruction, written out much more clearly, are in the OP. So why post it?
The instructions above are for LG LS980 SPRINT device
MakisPgr said:
The instructions above are for LG LS980 SPRINT device
Click to expand...
Click to collapse
... as are the instructions in the OP. The difference is that you posted ZV8 where the one in the OP is ZV7. Did you even read it... lol
Red_Kamel said:
Those files are already in the OP. Also those instruction, written out much more clearly, are in the OP. So why post it?
Click to expand...
Click to collapse
Sorry if I did something or said something wrong, I do not understand what is OP? I'm new to the Forum and just trying to help .... because I was a victim of similar problem.
MakisPgr said:
Sorry if I did something or said something wrong, I do not understand what is OP? I'm new to the Forum and just trying to help .... because I was a victim of similar problem.
Click to expand...
Click to collapse
No problem. OP =original post. The first post on this thread on the first page. Go back and read it. You will see that it is the same thing.
Red_Kamel said:
... as are the instructions in the OP. The difference is that you posted ZV8 where the one in the OP is ZV7. Did you even read it... lol
Click to expand...
Click to collapse
OUPS my mistake, yes you're quite right, now I understand, sorry for that.
MakisPgr said:
I had about the same problem, restored the appliance in the following way:
Turn off the device completely
Press the Vol+ and the power and opens in Factory Hard Reset process. push the power button twice to accept to start the process.
Restarted the device and opens in any situation.
Close the device completely.
Press Vol+ and you connect the USB cable and opens the device in Download mode-Firmware Update
Expect to finish installing the drivers on the computer.
do right click on my computer icon, choose Properties and Device Management choose the COM/LPT Ports there you will see your device to be attached to some COMx selects and do again properties-settings-Advanced-Port port number the change by COMx in COM41, press Ok and close all Windows.
Run the LGFlashTools program you choose the LGLS980_20130904_LGFLASHv151.dll and LS980ZV8_13.51097.tot, in Action Mode you choose UPGRADE DL and USB Connection Mode you choose.
from the icons you click the icon and choose serial is checked, all OK and close the window, then hit the yellow arrow and wait to complete control of files when your completed written ready.
Un-plug the USB from device to start the flash update process
Stock FIrmware
dll file
I wish to be helped
Click to expand...
Click to collapse
Thank you very much dear for your helping hand..
i tried as above but the trick didn't worked ..
its giving the same problem...
Check the Screen Shot...(attachment..)
[email protected] said:
Thank you very much dear for your helping hand..
i tried as above but the trick didn't worked ..
its giving the same problem...
Check the Screen Shot...(attachment..)
Click to expand...
Click to collapse
I'm not sure why you would try that when the original post has the exact same steps explained much more clearly. I woUld refer to OP and maybe try again following STEP BY STEP
As your device is recognized by the flash tool as an LS980 it should work. If you need clarification on how to do a particular step or few then I am glad to assist.
Please Assist..
It would be a great pleasure...
Now dear friends I will give the solution of problems that occur after unbrick leeco pro3 who has internal storage problem like this
infinite thanks to my Chinese friend Hua found this solution by itself and thanks tora33 from leeco.re and mbtt from forum.one-teams(i use picture from him)
I'm not in charge of the operation to be performed, is designed to assist you in these processes
Charge your mobile phone
1) download : qfil, (that have correct partition) and put in C:/
https://yadi.sk/d/piVn4bpf3MqcHC
2) download : FlashOne1,9 , put in a folder and extract it ,
https://yadi.sk/d/PmVChpqZ3Mj2hz
3) download :fastboot rom
https://yadi.sk/d/uzdwFhie3MqcJs
4)download qq driver
https://yadi.sk/d/U4SIDH3B3Mixsh
run "FlashOne1,9"
How to qfil Flash
When select qfil flash type, press power key, volume up and volume down key at the same time, then the phone enter into qfil mode, connect USB cable with PC, wait for PC install driver automatically, then press ‘Refresh’ button on the tool, serial port will display on UI, select the port you want to flash, and make sure there is no other qcom device connected.
Select corresponding flash zip file, the path of zip file should not contain Chinese and special character. (Under qfil mode, the tool can’t get hardware information, you should check if the software and hardware is matching yourself.)
Press ‘Flash’ button, then start to unzip flash zip file to current folder, but if there is already a corresponding unzip file existing, ‘Decompression folder is exist, re-decompress or not?’ dialog will pop up, if select yes, will re-decompress, else not. After unzip finished, start to flash the phone automatically, and the progress bar display flashing progress(for me the bar not move stuck %1 i did wait 15minute then unplug phone and push power button long time, and at the same time, the flashing log will also be shown on UI.
After flash complete or error happened, a notification dialog will pop up.
after phone start go boot logo and wait by the way open fastboot rom and push le_zl1_fastboot
everyting go fine u get 24gb for 32gb phone and 54gb for 64gb phone
good luck i hope help you
Thanks
Work on x720 ...
Will this work on Custom OMNI rom please?
krugerbud said:
Will this work on Custom OMNI rom please?
Click to expand...
Click to collapse
Yes it should work
All you have to do is follow the steps.
Be careful, all your data will be erased!
lazye53 said:
Yes it should work
All you have to do is follow the steps.
Be careful, all your data will be erased!
Click to expand...
Click to collapse
But I already have 24GB out of 32GB , but still have storage issues when using the phone. APps and services randomly crash unable to fully use phone.
I guess I do not need this then, must be some other issue?
krugerbud said:
But I already have 24GB out of 32GB , but still have storage issues when using the phone. APps and services randomly crash unable to fully use phone.
I guess I do not need this then, must be some other issue?
Click to expand...
Click to collapse
This issue is only for those who are missing storage.
If you have another storage problem, look for another solution.
Storage Problem LeEco Le Pro 3 X720 - 4 GB/32 GB
I followed instructions but it didn't work.
What can I do in order to increase storage to 24 GB?
qfil mode error
Is it for restoring the original storge capacity for Le Pro 3? The reason why I'm asking this is becuase I am currently stuck on qufil rom because it keeps making error everytime I tried to go to the launcher. Will it work on my circumstance?
After months of researching on how to downgrade Nokia 8.1, i finally find a way to do it.
NOTE: You don't need to unlock the bootloader
NOTE: Do this at your own risk!
NOTE: I'm not an expert in this stuff, but I will try to help you all I can. If you find there's a missing in the steps, make sure to tell me ASAP
(Steps)
1. Download the firmware/rom that you want to downgrade on
- I downloaded this (Android 9 stock) ---> https://bit.ly/3q6t7Vv
2. Extract the firmware file (If its in ZIP format) to somewhere you can access easily.
- the firmware format should be .nb0 or .mbn
3. Install Nokia Drivers (Idk if OST Tool will install the driver needed automatically )
4. Find a Nokia OST Tool free account in youtube or in any platforms like google and etc. (BECAUSE OST TOOL CRACK DONT WORK!!!)
- after you find a free account.
- enter the given mac address of that account to ---> device manager / Network Adapters / (your network controller) my network controller is "Realtek PCIe GbE Family Controller" / advance tab / Network Address / tick the value circle / enter the given mac address on the tutorial you find.
- after applying the mac address, go now and sign in the free account you got for OST Tool.
5. Install the OST Tool / OST LA version given on the video tutorial you find.
6. Open OST Tool / OST LA, (you can find it in start menu).
7. Type in, the free account you got.
8. You should be signed in now to OST Tool / OST LA
9. in Ost Tool, Click next
10. Click browse button and locate the firmware file you downloaded earlier. (.nb0 or .mbn)
11. then, set the update option to NORMAL DOWNLOAD, and ERASE USER DATA
12. Turn off you phone
13. once turned off, connect your phone to pc/laptop through the original charger cord. OST Tool should automatically detect your phone and set it to download mode. (If not make sure you install the drivers carefully, or do a computer restart.)
14. Click Next
15. Your device should now downloading the firmware from OST Tool
16. DO NOT DISCONNECT THE DEVICE
17. once done, your device will reboot
18. Congrats for successfully downgrading
19. make sure to set you mac address back to default.
NOTE: I'm not an expert in this stuff, but I will try to help you all I can. If you find there's a missing in the steps, make sure to tell me ASAP
Does this tuto would work on downgrading from 11 to 9 with lock bootloader and oem greyed out ?