Related
Hello,
I Have A Glofiish x610,
This Time When I Had A Hard Reset, It Hangs While Installing The Rom Softwares, So I Soft Reset The Device...
It Doesn't Load!
It Can't Be Hard Reset Too!
I Downloaded The exe File From Glofiish.com For Updating The Os But It Needs Active Sync! My Device Doesn't Load So I Can't Use Active Sync
Please Help Me
hi there
try thees Steps
1. Run the ROM update program on your PC and go through the installation process until your reach the ‘End User Update‘ window. Leave this running.
2. Go to the Temp file in your Documents. This is usually C:\Documents and Settings\username\Local Settings\Temp but it really depends on how you set up Windows.
3. Look for these 2 files, temp.dat (about 60 MB) and USBDLUpdate_Console.exe (about 4 KB) and copy them to your formatted SD Card using a card reader. You might want to copy these files to another location on your PC before copying it to your card reader if there are problems. Also, rename temp.dat to temp.bin before proceeding to the next step.
4. Put this card into your device and put the device into Bootloader mode. This can be done by pressing (and holding) the power button and voice commander key and then soft resetting. When it restarts, you can remove the stylus but keep your hold on the power and voice commander buttons.
5. The installation will proceed but at a slower rate than if you did it on your PC. This is due to the slower transfer rate between the card and device. It might take about 15-30 minutes so it would be best if your device was connected to the mains charger.
6. Installation is complete when you see this message “USB host is not connected yet“. This is your sign to do a soft reset and setup your device as the ROM installation was successful.
***
you may use this rom
http://rapidshare.com/files/314654442/Eten_X610_WWE.7z
just rename temp.dat to temp.bin put in formatted sd card
and go threw steps 4 to 6
any how you are welcome to
http://www.eten-users.eu/index.php?showforum=52
Hello,
I Tried All Ways & Your Roms On Etenusers
But My Boot Loader Shows a White Screen After Using Magic Numbers Method!
What Can I Do?
My Device Is x610 Samir 020 0702
One An Other That: My Booting With All The Roms That I Tested With Memory Card Method Long Only 4-5 Minutes! Isn't It Wrong?
Aha i got it now
Ok i got it now
I understand your problem
you cant do any thing for your device unless you have another Glofiish device (any model)
because your flasher is corrupted
if you find any working Glofiish device (any model) this is how to do it
1- connect the working device to Active Sync
2- download this tool http://rapidshare.com/files/254487467/UnLock_upgrade.rar
3- put one of my roms in the same folder of the tool.
4- open the upgrade.bat
5- flow the installation steps until the device goes to bootloader
6- now disconnect the working device from usb
7- put your device in boot loader mode connect your device to pc
8- push the update button .
and you are done
any how send me your mobile number as PM and i will call you as long as you are
in ksa
Oh A Big Problem!!!!
I'm In Iran & I Think There Are max 10 Glofiish Device In Iran!!!
Some Time My Boot Loader Work But Only With Sd Card
Isn't Any Other Solution?
I have another problem with x610. After hard reseting the phone after I pressed yes on deleting the files, I got myself callibrating the phone but the callibration stucks forever and it does not passes so the phone wont start...
Is there any solution? Please help as after searching I found nothing as a solution so I am asking here.
can I boot somehow from sd card? I mean formatting the phone?
nephew said:
Hello,
I Have A Glofiish x610,
This Time When I Had A Hard Reset, It Hangs While Installing The Rom Softwares, So I Soft Reset The Device...
It Doesn't Load!
It Can't Be Hard Reset Too!
I Downloaded The exe File From Glofiish.com For Updating The Os But It Needs Active Sync! My Device Doesn't Load So I Can't Use Active Sync
Please Help Me
Click to expand...
Click to collapse
To Hard reset x610 you need to press reset and on button, then press on button again while holding down end call(red) button, after some time erase all data option with timer will appear, press wifi/gps button that is listed under the YES option to change the times option or erasing data,
next screen will confirm your choice..
and we are back to square one and phone can be used again.. will all data lost..
probir_dev said:
To Hard reset x610 you need to press reset and on button, then press on button again while holding down end call(red) button, after some time erase all data option with timer will appear, press wifi/gps button that is listed under the YES option to change the times option or erasing data,
next screen will confirm your choice..
and we are back to square one and phone can be used again.. will all data lost..
Click to expand...
Click to collapse
Hi,
I tried as you said above, when I click YES it showed as bellow
"erase all data and load default ? (Yes)
please wait... "
and nothing had happened and it was showing like that continuously..
What should I do to get back my device?
please help me to sort out this.
thanks in advance..
Please help!
My HTC TP2 freezes at start up with the black screen and the Touch Pro2 Logo and some details in red at the bottom:
B 80
R 4.49.25.17
G 61.44tc.25.32U
D 1.86.67102
No USB connection can be established.
What happened:
1. Tried to update from original WM 6.1 to WM 6.5 by using the official HTC ROM update utility. Seems like USB connection broke during update and update freezed at 42%. Update utility process has stopped by itself (no process visible anymore in the Task Manager).
2. Restarted phone and multicolor screen appeared and stayed. After connecting with USB cable again "USB" appeared at the bottom. Started again the HTC ROM update utility which recognized the phone and started the update process again, but stopped at the beginning with an error message stating something like the ROM is broken.
3. Restarted again (by removing the battery and hit power button) and state reached like described above (HTC TP2 freezes at start up with the black screen and the Touch Pro2 Logo and some details in red at the bottom).
4. Performed a hard reset but did not help.
What can I do to bring the phone back to life?
So you can't or can get in the colored screen now? (the boatloader)
And it's kind of normal that their nothing happens after the tp2 + red information screen, this since their is no rom to startup.
EDIT
Is it possible to tell exactly what error you got?
EDIT
Try to hard reset your device, do you know how to do this?
If not this is how to do it:
To perform a hard reset
1. With the device turned off, press and hold the TALK/SEND, END and POWER buttons until you see this message on the screen.
"This operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel."
2. Release the TALK/SEND, END and POWER buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Source: http://forum.xda-developers.com/showthread.php?t=523083
This is just what worked for me..
Had the same issue on my tp...
Hope it will work for you.
Did already the hard reset - but this did not help as nothing changed!
One further info: whenever I insert the battery the device automatically starts up - until it freezes again at the start up.
Can someone please help?
It's normal that the device starts up when the battery is plugged in...
But this is just what I know out of my own experience.
So sorry I can't help you farther.
EDIT
Did some research you might want to try to flash your phone by micro sd... (not for sure if it helps but by some people it did work)
Read the tread about flashing at the top of the rhodium section and you know how to do it.
Did another trial: downloaded and copied a RHODIMG.nbh to the micro sd card, inserted it again and pressed volume up at startup -> colored screen appears shortly, then switches to a white screen telling "Loading..." in blue font color, but nothing more.
Is there anybody out there who can help?
Do I need a specific RHODIMG.nbh to make this approach working? I didn't flash this device before, so it has been still in the original manufacturer's state.
frieder01 said:
Did another trial: downloaded and copied a RHODIMG.nbh to the micro sd card, inserted it again and pressed volume up at startup -> colored screen appears shortly, then switches to a white screen telling "Loading..." in blue font color, but nothing more.
Is there anybody out there who can help?
Do I need a specific RHODIMG.nbh to make this approach working? I didn't flash this device before, so it has been still in the original manufacturer's state.
Click to expand...
Click to collapse
suppose 2 press down volume not up after soft reset
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Device is up and running again !
Could enter bootloader mode and tried first to install again via the official HTC installer -> worked!
Thanks a lot for your support!
great news welldone Bro and welcome to the forum!!!
osrix25 said:
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Click to expand...
Click to collapse
For future info, from what I have gathered you must hardSPl for all ROM flashes. If the ROM you flash is the stock ROM, you can also revert your SPL to stock. For any other ROM, you must leave your device hardSPL'd.
Hope I helped.
how were you able to connect the phone with the pc. i seem to have a similar problem but am finding it difficult to connect the phone to the pc. i have activesync installed but cannot connect to the phone
osrix said:
This may help,
Try entering bootloader by switching off device then switch back on holding down the Vol down key.
If you can enter bootloader this way then you wil be able to flash from SD card following the instructions from here
http://forum.xda-developers.com/showthread.php?t=550540
if you want to flash the Official update from HTC you can extract the Nbh from the Exe file you downloaded from them, just use winzip, Zzip or Win RAR to extract the contents from the Exe you are looking for RUU_signed.nbh..follow the above thread instructions to change the name of the file to RHODIMG.nbh.
I DONT KNOW IF YOU NEED TO HARD SPL FOR THIS..Probably better to do it than not. Can Anyone Confirm???
i hope this helps
Click to expand...
Click to collapse
is it possible to connect to active sync in bootloader, cos my phone cannot even boot, it freezes up with a white screen and htc logo.
After entering bootloader you can flash either way,either by ruu package provided by your ROM's maker or running official ruu release or if you have the renamed file on the root of your sd card....I never use sd card flashing and have never had a failed flash...If in bootloader it will not connect with activesync,but device should be recognized by ruu.exe
WC
Hi
I have an ASUS P526 and I had a problem of not being able to turn the PHONE function on.
The Communicaton Manager did not have the option to turn on the phone,
and I could not establish a USB connection to my PC via ActiveSync : It said "Cannot open UFN drivers"
I was using Windows Mobile 6.0
So I decided to flash the OS ROM. I downloaded SCHIST ROM v21864_clean and flashed the OS with the flash.dio.nb0 included in the download.
(i.e. I did not extract any flash.dio.nb0 files from my own ROM)
Now, when I turn on the phone, I get the Windows Mobile 6.5 SCHIST ROM 21864 clean screen and cannot log on to windows.
This is probably because I tried to flash an ASUS P526 with ASUS P527 ROM, but I could not find any other ROM to flash with.
When I download the original P526 ROM from the ASUS Website
(e.g. V618_WWE_Turkey_EXT_V158 ), I get a P526.pim file, but PIMSPLIT.EXE does not extract any " *.nb0 " files when I drag P526.pim onto it..
I am totally confused as to what to do at this point..
Please help!
I just want to be able to use Windows Mobile 6.0 , 6.1 or 6.5 with the phone, and be able to use the phone function, as well...
PS: The only way for me to flash the ROM on the phone, is with the SD card method, because ActiveSync does not work.
Hi
Tell me one thing, if you make a Softreset and click the OK button on the left will be in bootloader?
If so something can be done without sd.
The procedure is done using a ROM file.nbo, but first you must unlock the phone ...
Let me know and we'll see
Excuse my English
What do you mean Active Sync does not work? Is it a mechanical problem or a program incompatibility?
Try this: this is Expert mode in installing the Turkey ROM (or any other language).
Warning: Do this at your own risk! If not done right you might brick your phone! I will not be responsible for any damage done to your phone.
1.Make sure battery is fully charged.
2. connect your devide to PC using USB cable.
3. Run the ROM upgrade program you downloaded from ASUS site,
4. On the top bar of the installation window, "right click". A window will appear with the option "Expert Mode". Click on that. A message will appear in the window about connect USB or something (I'm sorry but I cannot remember the exact message since I have not done this in a long time).
5. Now you have to go to bootloader mode in your P526. Do this by pressing and HOLDING on the OK button <rocker switch on the left side> then press reset button <continue hoding down the rocker switch>. Your unit should go to the blue ASUS screen and a message will appear about being in USB mode or cable something <again I'm sorry I cannot remember exact message>.
6. If this appears then press the <Update> button on the installer window. This should start the installation proces.
Hope this helps. if you have any other questions or if this does not work please feel free to post again.
thanks for your good information
regards
ferdiebaq said:
What do you mean Active Sync does not work? Is it a mechanical problem or a program incompatibility?
Try this: this is Expert mode in installing the Turkey ROM (or any other language).
Warning: Do this at your own risk! If not done right you might brick your phone! I will not be responsible for any damage done to your phone.
1.Make sure battery is fully charged.
2. connect your devide to PC using USB cable.
3. Run the ROM upgrade program you downloaded from ASUS site,
4. On the top bar of the installation window, "right click". A window will appear with the option "Expert Mode". Click on that. A message will appear in the window about connect USB or something (I'm sorry but I cannot remember the exact message since I have not done this in a long time).
5. Now you have to go to bootloader mode in your P526. Do this by pressing and HOLDING on the OK button <rocker switch on the left side> then press reset button <continue hoding down the rocker switch>. Your unit should go to the blue ASUS screen and a message will appear about being in USB mode or cable something <again I'm sorry I cannot remember exact message>.
6. If this appears then press the <Update> button on the installer window. This should start the installation proces.
Hope this helps. if you have any other questions or if this does not work please feel free to post again.
Click to expand...
Click to collapse
my phone fails to complete the upgrade and did not able to boot. I tried to do a hard reset, but the same thing.. please help
I only connect my ZE551ML to my Windows 7 x64 when I've got to do firmware updates or transfer music, and I haven't done either in a while.
On my "MTP USB Device" driver I'm now getting: This device cannot start. (Code 10)
The ASUS Android Composite ADB and PC Link Interface drivers are loaded and fine.
Things that I've tried:
- the Asus android drivers
- the Intel android drivers
- the universal ADB drivers.
- different USB cables
- different USB slots
The perplexing thing is that the image that allows you to install "ASUS ZenUI PC Suite" is available as a CD drive, "PC Link" works when mirroring my phone onto my computer and using ADB from a command prompt can see my device.
I don't know what I've installed between the last time it worked to now, and I'm at wit's end with what I can do.
Anyone have a suggestion at a possible next step?
Do you by any chance have Windows 7N (one without media player)?
Mine did the same when i connected the missus MTK device.
Unfortunately i need hers to stay for future updates and for using MTK flashtools too.
Great news is the( share link ) built in asus app in M - never used it before until this , click asus share link app on phone whilst connect to PC (for the first installation) and then you can transfer to an from pc to sd (either sd) in share link settings.
Then after - uses your network for transfer ,no cables , saves charge port i guess and its -- Fast !
USBdeview can be used if you want to see/want/remove if old/new drivers might be causing conflicts but am quite happy with the share link app now,ps i`m on windows 10 and too also not sure whether an update came whilst installing MTK destroyed it too
chiudikas said:
Do you by any chance have Windows 7N (one without media player)?
Click to expand...
Click to collapse
No, I'm running Home Premium, and have both media player and media center.
timbernot said:
Mine did the same when i connected the missus MTK device.
Unfortunately i need hers to stay for future updates and for using MTK flashtools too.
Great news is the( share link ) built in asus app in M - never used it before until this , click asus share link app on phone whilst connect to PC (for the first installation) and then you can transfer to an from pc to sd (either sd) in share link settings.
Then after - uses your network for transfer ,no cables , saves charge port i guess and its -- Fast !
USBdeview can be used if you want to see/want/remove if old/new drivers might be causing conflicts but am quite happy with the share link app now,ps i`m on windows 10 and too also not sure whether an update came whilst installing MTK destroyed it too
Click to expand...
Click to collapse
I'm still on Lollipop... Though it does have a sharelink app as well. I've tried setting it up, and on my phone it can't see my microSD card.
I'll give USBdeview a go and see if uninstalling all the Samsung/Asus/Intel drivers does anything.
It's the strangest thing... why would I be able to see it in ADB, be able to install the PC Link programs from the ROM and yet not be able to see internal storage?
azthemansays said:
No, I'm running Home Premium, and have both media player and media center.
I'm still on Lollipop... Though it does have a sharelink app as well. I've tried setting it up, and on my phone it can't see my microSD card.
I'll give USBdeview a go and see if uninstalling all the Samsung/Asus/Intel drivers does anything.
It's the strangest thing... why would I be able to see it in ADB, be able to install the PC Link programs from the ROM and yet not be able to see internal storage?
Click to expand...
Click to collapse
Share link app - 3 dots -settings - storage location - click on /sdcard -- opens up to show internal sd and whatever your ext sd is called --select your choice -- click OK , you may have to allow rights to it in file manager :good:
Usbdeview should be ok
Why it happens ? conflicts with drivers i suspect
timbernot said:
Share link app - 3 dots -settings - storage location - click on /sdcard -- opens up to show internal sd and whatever your ext sd is called --select your choice -- click OK , you may have to allow rights to it in file manager :good:
Click to expand...
Click to collapse
That's the issue, when I get to that point it only shows "Internal Storage." As an aside, my phone's bootloader is unlocked and it's rooted.
*EDIT* - When I get to the part where I choose the directory, the file manager comes up with the "Recent" page. if I press the menu button, I get the option to hide SD card and file size, but in the list to the left it only lists "Internal Storage"
timbernot said:
Usbdeview should be ok
Why it happens ? conflicts with drivers i suspect
Click to expand...
Click to collapse
I just removed all the drivers that I could tell were related and am about to reboot.
phone settings - storage -- eject sd -- remount , set up sd for ext storage ? Never used this before so am at a loss , my ext sd was there when i clicked on /sdcard along side internal and after OK i followed on screen commands to allow it . Again , this is in M and never used it before on LP.
When you open file manager , your sd is there alongside internal or blanked out ?
Good luck hope you get it sorted , keep us posted BBFN
timbernot said:
phone settings - storage -- eject sd -- remount , set up sd for ext storage ? Never used this before so am at a loss , my ext sd was there when i clicked on /sdcard along side internal and after OK i followed on screen commands to allow it . Again , this is in M and never used it before on LP.
When you open file manager , your sd is there alongside internal or blanked out ?
Good luck hope you get it sorted , keep us posted BBFN
Click to expand...
Click to collapse
Still run into the same issue after remounting. It lets me select my internal, but not my SD. I guess it'll have to do for the time being - use it to move from computer to internal, then move it from internal to external.
And Removing selective ones in USBdeview still gave me the same issue:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
so I went ahead and uninstalled all the ones that were for the specific USB slot, and am about to reset. Fingers crossed...
Ok try the info in ASUS file manager
open file manger , 3 dots , about , help and feedback , 2nd box down
ps , the time you spent trying to fix this
upgrade to M latest , better battery etc etc
timbernot said:
Ok try the info in ASUS file manager
open file manger , 3 dots , about , help and feedback , 2nd box down
ps , the time you spent trying to fix this
upgrade to M latest , better battery etc etc
Click to expand...
Click to collapse
I can't upgrade to M without being able to transfer files to my phone :laugh::crying:
And more importantly, I don't know if upgrading would change anything when it comes to the Windows 7 drivers. I keep trying to update driver to the Asus ones, but it keeps reverting to the generic "MTP USB Device" one. I've even tried to go into the windows inf files and remove that generic driver, but then windows won't accept the Asus ones at all.
When I go into the "feedback and help" section I get an error:
I've just about had it up to here with this phone. At the beginning it was giving me similar issues but I managed to sort it out... and now we're back to the issues that occurred back near the phone's launch. Full goddamn circle.
What build /date in settings ?
We gonna get you updated v soon .
First you need to unroot it.
Then fastboot flash stock recovery which corresponds with your build..
Then adb sideload a fresh copy of the build your on .You know how to perform these tasks above ???
If not , we do it soon
last but least don't smash it up
Have a read thru here to get general idea what needs doing
http://forum.xda-developers.com/zenfone2/help/how-recovery-t3514205
---------- Post added at 02:53 AM ---------- Previous post was at 02:44 AM ----------
azthemansays said:
I can't upgrade to M without being able to transfer files to my phone :laugh::crying:
And more importantly, I don't know if upgrading would change anything when it comes to the Windows 7 drivers. I keep trying to update driver to the Asus ones, but it keeps reverting to the generic "MTP USB Device" one. I've even tried to go into the windows inf files and remove that generic driver, but then windows won't accept the Asus ones at all.
When I go into the "feedback and help" section I get an error:
I've just about had it up to here with this phone. At the beginning it was giving me similar issues but I managed to sort it out... and now we're back to the issues that occurred back near the phone's launch. Full goddamn circle.
Click to expand...
Click to collapse
keep cal.m
timbernot said:
What build /date in settings ?
We gonna get you updated v soon .
First you need to unroot it.
Then fastboot flash stock recovery which corresponds with your build..
Then adb sideload a fresh copy of the build your on .You know how to perform these tasks above ???
If not , we do it soon
last but least don't smash it up
keep cal.m
Click to expand...
Click to collapse
Haha, thank you. I'll try to stay calm.
I'm sitting at 194 right now and the security patch level was last updated July 1, 2016.
This phone is my daily driver and I need to go to bed, but I'll Titanium Backup the apps and make a nandroid backup tomorrow as soon as I get home from work so I can start flashing.
It's been awhile... should I flash back the stock recovery before I unroot? And it's been giving me issues with the micro SD card occasionally unmounting on it's own as well as Google Play services crashing at random times (I've tried all the tricks & tips up to uninstalling it to get rid of corrupted installation, but it still persists)... Should I do a factory reset after flashing the stock image just to try to clear everything up? I'd have to move everything to my microSD card first though...
azthemansays said:
Haha, thank you. I'll try to stay calm.
I'm sitting at 194 right now and the security patch level was last updated July 1, 2016.
This phone is my daily driver and I need to go to bed, but I'll Titanium Backup the apps and make a nandroid backup tomorrow as soon as I get home from work so I can start flashing.
It's been awhile... should I flash back the stock recovery before I unroot? And it's been giving me issues with the micro SD card occasionally unmounting on it's own as well as Google Play services crashing at random times (I've tried all the tricks & tips up to uninstalling it to get rid of corrupted installation, but it still persists)... Should I do a factory reset after flashing the stock image just to try to clear everything up? I'd have to move everything to my microSD card first though...
Click to expand...
Click to collapse
First - transfer your stuff to pc off internal thru sharelink
unroot , flash back stock recovery .194 - reboot to recovery , update over adb , adb sideload .196 stock firmware , which should be renamed to MOFD_SDUPDATE and put in your fastboot/adb folder previously
adb cmd >
adb sideload MOFD_SDUPDATE.zip
set up not connecting to wifi - skip everything you can-- factory reset .
Set up correctly this time . Run for 3 days without any modifications . Make sure everything is running correctly :good:
timbernot said:
First - transfer your stuff to pc off internal thru sharelink
Click to expand...
Click to collapse
Already running into issues with the first step. Share Link gets to about 100mb transferred, then my phone's screen blacks out and is non-responsive, though it shows touchscreen presses (I have that turned on in developer settings). The transfer hits around 200mb and then the transfer gets cancelled. It's also rebooted twice.
This is getting to ludicrous levels.
*EDIT* - I tried uninstalling all the USB controllers in Windows Device manager in case they were corrupted, but I'm still getting the same failure with the generic "MTP USB Device" being installed instead of the Asus one and still getting that yellow exclamation mark. When I try to update it to the Asus one, it fails and disappears when I unplug and replug the phone. This is maddening because it was working in October...
*EDIT 2* - I'm thinking of testing it on another windows installation... I've got some spare HD space that i could partition and install another copy of my Win 7 on to see if it's my Windows or phone that's corrupted. If it's not my phone, I'll be able to transfer everything out...
Hey some news , after reading what you are experiencing - I remembered i have another lappy with windows 10 on in bedroom wardrobe - Not been used for nearly a yr , fired it up with wifi off and both my drives are visible
So , mine IS either MTK driver conflict or a windows update or both
Whatever , i will update it today and test further.
This does`nt explain your sharelink probs tho, mine transferred 443mbs of CM14.1 in 3 mins just now with the same prob you have.
Use file manager instead to transfer to ext SD. Instead of sharelink
And go about sorting it out , with whats already mentioned and with the fresh copy of 7 - hopefully it is windows and not the phone you said you had probs with from new
So it failed to install the driver in the new Windows 7 install, but somehow booting into recovery allowed me to access and copy everything off of internal storage. But of course, booting back into normal mode breaks it again.
I'm just going through backing up my SMS and using Titanium backup for the apps and I'll be ready to take the next step.
azthemansays said:
So it failed to install the driver in the new Windows 7 install, but somehow booting into recovery allowed me to access and copy everything off of internal storage. But of course, booting back into normal mode breaks it again.
I'm just going through backing up my SMS and using Titanium backup for the apps and I'll be ready to take the next step.
Click to expand...
Click to collapse
Are you familiar with flashtools ?
It's just another method to flash a raw file in fastboot boot loader state .and boots you into system by itself after about 10 mins..but I'm a bit unsure you should use it with the probs re screen blanking earlier with share app.
Maybe we keep that as a last resort
good luck
timbernot said:
Are you familiar with flashtools ?
It's just another method to flash a raw file in fastboot boot loader state .and boots you into system by itself after about 10 mins..but I'm a bit unsure you should use it with the probs re screen blanking earlier with share app.
Maybe we keep that as a last resort
good luck
Click to expand...
Click to collapse
My usual method of Flashing OTAs and ROMS was using this guide. I'm not familiar with flashtools, but I've used Odin before and I'm a quick study.
Now, I've got a few things that I would normally take back to stock/remove before unrooting and updating:
- Adaway hosts files
- busybox
- Viper4android sound.conf mod
- build.prop modification for permissive SELinux
- might be more but I can't remember.
I also recall flashing a new kernel at some point, but it was a while ago and I don't remember how to find out if what I have now is stock or not. I think it was this one.
Do I need to worry about taking all that back to stock before reflashing .194?
I usually edit the OTAs so I could flash them with TWRP, so I never had to flash stock recovery back in the past... what's the ADB name for the recovery partition?
*EDIT* - I'm also not familiar with all this new stuff like Magisk 8 and seamless root. Is this the go-to method for rooting 6.0? I like the sound of being able to root and unroot on the fly to bypass root detection by apps. I think I want to flash CleanSTOCK rather than just stock MM if it's less bloated.
azthemansays said:
My usual method of Flashing OTAs and ROMS was using this guide. I'm not familiar with flashtools, but I've used Odin before and I'm a quick study.
Now, I've got a few things that I would normally take back to stock/remove before unrooting and updating:
- Adaway hosts files
- busybox
- Viper4android sound.conf mod
- build.prop modification for permissive SELinux
- might be more but I can't remember.
I also recall flashing a new kernel at some point, but it was a while ago and I don't remember how to find out if what I have now is stock or not. I think it was this one.
Do I need to worry about taking all that back to stock before reflashing .194?
I usually edit the OTAs so I could flash them with TWRP, so I never had to flash stock recovery back in the past... what's the ADB name for the recovery partition?
*EDIT* - I'm also not familiar with all this new stuff like Magisk 8 and seamless root. Is this the go-to method for rooting 6.0? I like the sound of being able to root and unroot on the fly to bypass root detection by apps. I think I want to flash CleanSTOCK rather than just stock MM if it's less bloated.
Click to expand...
Click to collapse
Lets just get you up and running stock for a few days -- No mods ok ?
I think its best we flash raw at bootloader state , refresh here i will add files to download ready and info how to:good:
Flashtools - http://www.mediafire.com/file/sm76jyyz8t1axmz/AsusFlashToolInstaller_1.0.0.17.rar install and run as admin
Raw collection of and thanks go to Realyoti there - choose .196, bottom one last of the LP
https://yadi.sk/d/FijRoAVJtvRiG
Video
Ignore the first 2:17 mins - fast forward to 2:18 mins for flashtool flash and adding raw and general settings > choose wipe data to prevent any bugs from previous state
Note -- you just let it complete on its own , the video goes to show how to correct serial number , you dont need to -- once it starts flashing - let it finish
https://www.youtube.com/watch?v=PmbRaJijIBs&feature=youtu.be
When up n running say a thank you to Realyoti here please
http://forum.xda-developers.com/zenfone2/general/z008-z00a-z00d-z00x-raw-fw-collection-t3448966
timbernot said:
Lets just get you up and running stock for a few days -- No mods ok ?
Click to expand...
Click to collapse
Haha, sorry for putting the cart before the donkey at the end there...
But I was asking if I need to remove any/all of these mods before flashing the raw file? And does the raw file also include the recovery partition? That's why I was asking where to flash "recovery.img" to go from TWRP to stock recovery...
Just 19% into transferring all my Titanium backups to Google Drive right now.
In this guide, I will show how to how to change from LVM to Chinese unification storage method. Windows OS Only.
This guide is specifically for Oppo Find 7(A/S).
The idea of changing to chinese unification storage method is to have access to 8.1 Android operating system and future Android OS builds.
Please follow these following steps in order be able to run 8.1 Android on your OPPO Find 7.
1) Back up only your internal storage because after you flash the following tools, the internal storage will be wiped completely.
2) Download this file (for OPPO Find 7s) and this file (for OPPO Find 7a) then run the following steps:
Extract the files, and locate the QcomMtk_Driver_Setup.exe (*install this driver*) and reboot your computer system.
After rebooting, take off the battery off the Oppo find 7 and press the volume up button and connect to the PC using a micro USB cable. Go to the device manager, open the ports tab and there should be something like qualcomm etc. If there is no warning sign then you are fine and you should proceed along the steps. If there is a warning sign, just right click on the driver and update by letting windows finding the appropriate drivers.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then go back to the folder where you extract the zip file and locate (X9077_Android5.0_32G_20150520.exe) or X9007 respectively and run as administrator. rights only.
Agree with the licence. As shown in the image.
Now, again, make sure your battery is removed, hold volume up button and connect to the pc.
Click the first top left button as indicated in the image below.
Now, the software should do the rest so please be patient and wait until the green line has finished and the timeclock down on the bottom right as come to a halt.
After the green line has finished, please remove your device and plug back your battery. Let the device fully boot up before moving on the following steps.
After you get to the setup screen. Press and hold the power off button and shutdown fully before going back to the fast boot mode by pressing volume up and power button at the same time, the battery needs to be installed this time.
-
Now, flash the twrp modded image using fast boot flash and download the two files fastboot and twrp-modded img :
1) Have your phone in bootloader mode. (Turn off your phone, press volume up button and power button together and connect usb).
2) Navigate to the folder and click on the top left of the folder and copy that. e.g C:\Users\samgi\Desktop\platform-tools
3) Open cmd and type in: cd C:\Users\samgi\Desktop\platform-tools
4) In cmd type in: fastboot flash recovery image-modded.img
4) Remove USB and press power button and volume down button simultaneously.
-After you have flashed the recovery, boot into recovery and store the ROM, GAPPS and cm13 unified patch in the external sd card using your USB.
Download your favourite 9.0 ROM:
crDroid for example: https://androidfilehost.com/?w=files&flid=262369
Install GAPPS (only pico):
http://opengapps.org/
After you have downloaded all the files rom gapps cm13 patch etc. Make sure to flash each of the zip files one by one:
1) Flash ROM
2)Flash Pico Gapps
3)Flash CM13 Patch here
So basically, just head over to https://download.lineageos.org/find7 and download the latest Lineage OS 16 ROM. Then download the MindTheGapps (since pico OpenGapps can't work) from https://androidfilehost.com/?w=files&flid=170282 make sure to get 9.0.0arm.
Reboot to recovery, wipe the dalvik, system and cache. Then proceed with installing the the LOS 16 ROM. After that, you can flash the CM 13 patch and the gapps (MindTheGapps). It's ok to do gapps first before the CM 13 patch. I noticed that it makes no difference. Works the same every time.
Well, that's about it, reboot and enjoy. OTA should work after this. I think.
Good luck.
Then, simply clear cache and boot to your 9.0 OS. P.S don't forget to restore your data that you deleted in step one.
Optional: If you want to go back to Color OS or you have hard-bricked your OPPO Find 7(A/S) this tool will help you get back to stock firmware.
STOCK FIRMWARE (LVM)
Here are the instructions to unbrick your phone:
This is going to be a step by step guide on how to unbrick your OPPO FIND 7 (A/S)
Before attempting this guide, Windows is needed to be in "Test Mode".
To do this:
1) Open CMD with admin rights, and type "bcdedit /set testsigning on" without the colons.
2) Restart your computer.
End result:
This will check if this guide is applicable.
Note: Make sure your device has at least 70% battery. Charge it for an hour or so if you are not sure about the amount of battery left.
Note 2: I'll assume you are an admin of the computer you are using.
1) Disconnect your device from your charger/computer, etc.
2) Take out the battery and wait for 5 seconds.
3) Put the battery back in, hold the Power+Volume Up buttons and plug it into the computer.
4) Release your hands, and go to Device Manager. (How to go to device manager below)
1. Click the start menu
2. Right click Computer (Right hand side)
3. Click Properties
4. On the left hand side, click on Device Manager
5) Under Ports, you'll see either QHSUSB_BULK or Qualcomm *blah blah blah* 9006/9008
If you don't see any of the three, you're doing it wrong (Probably).
If you're not seeing it, try connecting your device without the battery.
Next, we uninstall the drivers. Simple enough.
WARNING: This part is only for people seeing Qualcomm 9006/9008 in Device Manager.
1) Uninstall the driver. (Right click your device, then click Uninstall. If prompted, delete driver software too)
2) Unplug your device.
3) Take out the battery and wait for 5 seconds.
4) Put the battery back in, hold the Power+Volume Up buttons and plug it into the computer.
5) Release your hands, and go to Device Manager.
You should see QHSUSB_BULK, if not, you might be doing it wrong.
Now we install the proper drivers.
NOTE: You should be seeing QHSUSB_BULK in your Device Manager, if not you're doing it wrong.
1) Download the Find 5 Drivers and unzip the file anywhere.
2) Right click on your device showing QHSUSB_BULK and click on Update Driver Software.
3) Click on "Browse my computer for driver software", and select the folder in which you extracted the drivers to.
4) It will install automagically. If prompted, click on Install the driver anyway.
After installing, your device should say Qualcomm *blah blah blah* 9006/9008.
The moment all of you have been waiting for. Unbrick!
NOTE: Your device should be connected at all times.
1) Download the tool that will save you below.
2) Extract the contents from the zip file.
3) Open the .exe file with admin rights.
4) There should be a line that is visibly different from others.
5) If there is, click start and wait till that line turns green. (It takes a few minutes. Generally nothing should go wrong at this stage.) If there isn't, you're doing it wrong.
6) After the line turns green, unplug your device and hold the power button until you see the Oppo logo.
7) If all goes well, you should be booted to ColourOS v1.2.5i.
If everything went through smoothly, you should be unbricked and ready to brick your device again.
Special thanks to:
@tashimotor https://forum.xda-developers.com/showpost.php?p=64149659&postcount=3
@Manas1796 thread: https://forum.xda-developers.com/find-7/general/7-dead-development-oppo-7-terminated-t3764649
@crdroid
@ akmlfhm https://forum.xda-developers.com/find-7/help/how-to-debrick-unbricka-oppo-7-7a-t3717802
@play8oy
A very helpful thread, my friend! Thanks for keeping us up to date that this is possible!
Glad to see a detailed method of Unification! Can't wait till you post one for the Find 7a
5ufy9n said:
Glad to see a detailed method of Unification! Can't wait till you post one for the Find 7a
Click to expand...
Click to collapse
Sure, I will let you know once I upload the file to Google Drive. :fingers-crossed:
Nice... looking this step... because last i try switch lvm to chns unified.. got bricked
So my question is ....
1. Support for find7 with this model X9076? Because the file download is X9077
2. What windows u running when u doing this?
3. Is possible support for windows 10.1 64 bit?
4. any suggest what custom rom ?
Cant wait u reply.....
Tq....
itmdn said:
Nice... looking this step... because last i try switch lvm to chns unified.. got bricked
So my question is ....
1. Support for find7 with this model X9076? Because the file download is X9077
2. What windows u running when u doing this?
3. Is possible support for windows 10.1 64 bit?
4. any suggest what custom rom ?
Cant wait u reply.....
Tq....
Click to expand...
Click to collapse
Sorry for the late reply,
Don't worry, I will upload the tool also that I managed to download when oppo forums was running and luckily saved that on my hard drive :') so if you do brick your phone, the software will put you back to default X9076 color OS software mode so you're safe.
1. This guide is for Oppo Find 7s. The 8.1 android OS does not recognise X9076 (LVM) and shows "encryption unsuccessful" whenever you boot into the OS. However, when your phone shows X9077 (Chinese unified method) the 8.1 recognises and lets you boot successfully. I'm not quite sure why OPPO had to make this sooooo confusing. Lol.
2. I am running the latest Windows 10 Anniversary Update.
3. I'm not sure what you're asking ? It does not matter 32-bit or 64 bit
4. I'm literally running CrDroid and its amazing, the latest update just got out online check it out.
Let me know if you need further help.
brownboy1289 said:
Sorry for the late reply,
Don't worry, I will upload the tool also that I managed to download when oppo forums was running and luckily saved that on my hard drive :') so if you do brick your phone, the software will put you back to default X9076 color OS software mode so you're safe.
sorry, is this your mean u will upload the X9076_Android5.0_32G_20150520 version?
or you are saying that files at OP is working for X9076 and X9077 ?
sorry .... cant wait anymore ... really need switch from lvm to chns unified and taste the Android 8.1
tq
Click to expand...
Click to collapse
i success do it, but now i got new problem, at my storage sdcard0 corrupted, tried format still no luck.
any help or suggestion ?
tq
---------- Post added at 08:33 AM ---------- Previous post was at 07:56 AM ----------
itmdn said:
i success do it, but now i got new problem, at my storage sdcard0 corrupted, tried format still no luck.
any help or suggestion ?
tq
Click to expand...
Click to collapse
already solved.
first try ... got problem sdcard0 corrupt.
so i do this step, boot to twrp, flash removesetuplvm.zip - done
repeat again the guide at OP and now sdcard0 corrupted problem is gone.
now ... time for me taste android 8.1 and restore all my data
tq for this guide
itmdn said:
i success do it, but now i got new problem, at my storage sdcard0 corrupted, tried format still no luck.
any help or suggestion ?
tq
---------- Post added at 08:33 AM ---------- Previous post was at 07:56 AM ----------
already solved.
first try ... got problem sdcard0 corrupt.
so i do this step, boot to twrp, flash removesetuplvm.zip - done
repeat again the guide at OP and now sdcard0 corrupted problem is gone.
now ... time for me taste android 8.1 and restore all my data
tq for this guide
Click to expand...
Click to collapse
I'm glad that it is working for you. :fingers-crossed::good:
Let me know if you have any problems
Sorry for those waiting on the OPPO FIND 7a files, I have really slow upload speed.
5ufy9n said:
Glad to see a detailed method of Unification! Can't wait till you post one for the Find 7a
Click to expand...
Click to collapse
Up and running: https://drive.google.com/file/d/1h74LKVucM4RoBJ-Bsgkmzdavzn_MbtPY/view?usp=sharing
Can some post thread in this xda where is crdroid oreo discussion? Because i have strange problem with crdroid...
Tq
itmdn said:
Can some post thread in this xda where is crdroid oreo discussion? Because i have strange problem with crdroid...
Tq
Click to expand...
Click to collapse
What's the problem? I think they had a 7.1 forum but I'm not sure if it's closed
If 7.1 i think no connection on this 8.1 version, right? But if u dont mind i wanna ask if u have this issues.
My problem is weird ....
1. Press long at recent button will appear some apps that we have opened.. at the top have lock button, right? I already press that button become lock. But that make it permanent... in no time will be unlock.
2. Last night when i sleep i leave my phone idle with battery 100%, at morning i woke up and see my phone low batt with 13%. Weird draining battery so fast. Nothing running only some email and chat that i haven' t read. Maybe the notification light?
Tq.
itmdn said:
If 7.1 i think no connection on this 8.1 version, right? But if u dont mind i wanna ask if u have this issues.
My problem is weird ....
1. Press long at recent button will appear some apps that we have opened.. at the top have lock button, right? I already press that button become lock. But that make it permanent... in no time will be unlock.
2. Last night when i sleep i leave my phone idle with battery 100%, at morning i woke up and see my phone low batt with 13%. Weird draining battery so fast. Nothing running only some email and chat that i haven' t read. Maybe the notification light?
Tq.
Click to expand...
Click to collapse
The first problem I'm not sure lol ?
The second problem is maybe most likely of background apps turn off any background apps that might be running i.e apps that run constantly Facebook Instagram others. One recommendation to turn off Wifi and mobile data so there is no data incoming/outgoing when you go bed.
brownboy1289 said:
The first problem I'm not sure lol ?
The second problem is maybe most likely of background apps turn off any background apps that might be running i.e apps that run constantly Facebook Instagram others. One recommendation to turn off Wifi and mobile data so there is no data incoming/outgoing when you go bed.
Click to expand...
Click to collapse
Maybe my english bad hehehehhe
I already attach the pic for first problem....
I cant make it stick locked ... in some how it will unlock itself... weird...
Also i cant play Mobile Legends anymore always force-close lol
Tq
That,s weird battery usage. When I leave a 100% battery at night, next morning ( about 8 hours) I have about 90+% left, and I leave WiFi and mobile data on all night. Though I use Servicely and Project Skynet Raising.
itmdn said:
Maybe my english bad hehehehhe
I already attach the pic for first problem....
I cant make it stick locked ... in some how it will unlock itself... weird...
Also i cant play Mobile Legends anymore always force-close lol
Tq
Click to expand...
Click to collapse
This is a strange problem I'm not quite sure how to help... sorry
Omg so frustrating ..... battery really draining... lol. In 1 day i can charge 3x .... any suggest official custom rom with android 8.1 for find 7s?
Tq
itmdn said:
Omg so frustrating ..... battery really draining... lol. In 1 day i can charge 3x .... any suggest official custom rom with android 8.1 for find 7s?
Tq
Click to expand...
Click to collapse
Best advice would be to reflash the ROM with pico gapps or at last change to another 8.1 ROM i.e lineage rom or omni 8.0