My watch has entered a weird state. Probably after an update but I haven't noticed anything.
While off charger, it just tries to restart all the time. The screen is black and every 10 seconds it does once or twice a short vibration. In one case I noticed it went further with the boot up sequence and occasionally I can see bootloader / fastboot there (dark screen, small colorful text, debug info). This is happening until the battery dies off.
When I put it on charger, it usually starts booting up. It often goes up to the "Installing apps 1 of 20" screen. Very often it restarts itself during this phase but sometimes it goes beyond that and the watch actually starts. I can see the charging indicator and change it colors with swipe.
If removed from the charger, it immediately dies
What's weird that after a while, the charging indicator disappears and is replaced with the actual Android Wear interface I can interact with. I tried to go to settings and hit reset, but it just restarts the watch. Doesn't do the reset.
Usually the longer the watch sits in the charger, the worse the behavior is (ie it's just constantly restarting after a while). I get the best results when I let the battery die and then put it on the charger.
Also the watch is really really warm the whole time.
To me it seems like a software problem. If it was a phone, I'd just invoke factory reset somehow, over the cable or through boot menu. Is there a trick how to do it with the watch as well? Are there any stores with required equipment? I really don't want to send it back.
Same here mate, did you eventually solve it?? How? I really don't want to return it..
nicofit said:
Same here mate, did you eventually solve it?? How? I really don't want to return it..
Click to expand...
Click to collapse
I did not. I used my warranty and sent it back to Motorola. I have a new watch now.
I understand that you don't want to return it. The process was extremely long, painful and annoying. They decided that I'm entitled to get a new watch pretty quickly and sent me a coupon for a new one. I never got that coupon. I spent lots of time calling Motorola trying to find out what was going on and it took a couple of weeks before they found where the mistake was. When they finally sent me the coupon, it was only for the base watch, it did not cover the metal band and the special bezel that my original watch had. So more calls and e-mails to Motorola followed...
Anyway, I know this is the last thing you want to hear but the sooner you accept that your watch is just broken, the sooner you'll get a new one I wish you more luck than I had.
tobice said:
I did not. I used my warranty and sent it back to Motorola. I have a new watch now.
I understand that you don't want to return it. The process was extremely long, painful and annoying. They decided that I'm entitled to get a new watch pretty quickly and sent me a coupon for a new one. I never got that coupon. I spent lots of time calling Motorola trying to find out what was going on and it took a couple of weeks before they found where the mistake was. When they finally sent me the coupon, it was only for the base watch, it did not cover the metal band and the special bezel that my original watch had. So more calls and e-mails to Motorola followed...
Anyway, I know this is the last thing you want to hear but the sooner you accept that your watch is just broken, the sooner you'll get a new one I wish you more luck than I had.
Click to expand...
Click to collapse
You're right, not what I wanted to read... I turned it off now, with the silly hope to wake up tomorrow and see it working again. While leaving it on the charger it became way too warm.
The worst is that this is my wife's watch, and she is even less patient than I am
Damn
Hello,
I have the almost the same issue. Last Friday my watch died randomly when I walked home from work. The screen went black, flashed a bit in different colors and then died. Haven't been able to turn it on since. When I try to charge it, it keeps getting stuck in a reboot loop. I can't do nothing...super annoying. It's been 10 months for me since I bought it but I guess that's out of these "6 months warranty" that then give. Crazy, only 6 months!
Same issue
Does soneone has a solition so far?
wjhessels said:
Does soneone has a solition so far?
Click to expand...
Click to collapse
have you tried getting it on to bootloader whilst on the charger just hold the power button down mine does it sometimes but it boots eventualy
Related
Hello XDA members, this time I'm writing to all of you to tell you something that happened to my Optimus G E987 from Claro Argentina, also, to ask you something related to the topic.
I bought this phone about 4-5 months ago, and I have taken really good care of it, without using any film protection or case, it was working perfect and with not a single scratch on it, not even a little hit.
But then, some days ago, I decided to "protect it" a little bit, so I got one of this:
htt-p://i[dot]imgur[dot]com/YtgK1aS[dot]jpg
htt-p://i[dot]imgur.com/la1kI5e[dot]jpg
(Sorry, I'm new to this forum so it won't let me post links)
I used it like.. dunno, 3-4 days. One night, my phone was on 53% battery, to lazy to charge it so I just let it like that. Next day I gave it some use, so it dropped to 33% of battery life, I had to go work so I turned it off. When I finished, I tried to turn it on again, but nothing happened, tried more times and nothing, then I noticed I liiiitle light in the screen, the phone was turned on, but with REALLY low visibility, almost everything black but with a little of sight.
I though it was just a battery problem, so I charged it, but to my surprise, nothing happened, well something did happen, the little bit of sight that I had just went full black with no visibility. I noticed that the touch screen and buttons actually worked, I could "easily" navigate through the phone by just using it as normal, but without seeing (you can do this by just knowing your phone a bit).
And that's the story, basically, after using that case, the phone "casually" stopped working properly, all I got was a functionally phone with a black screen.
I managed to connect it to my pc through wifi and launched Android Screen Cast, to see what was happening on my phone. The glow was at 100% (I tried changing it) and everything seemed normal.
If you don't want to read, here is a TL;DR
>Bought Magnetic* Flip Stand Leather Wallet Case for Optimus G
>Some days after, phone screen stopped working (phone was still normally working, just with a full black screen)
About the Magnetic thing.. is there any possibility that this was the problem? the magnetic thing?
Btw, I sent the phone to tech service because it was still on warranty and they have me a new one, now I'm scared of putting it again in the leather case I bought, I don't want this to happen again.
Something to comment? hope you can give me some advice, thanks in advance!
Also having similar problems as you. Somehow, i am quite sure its the stock rom causing the problem.
Had the very same issue few weeks ago, had to send the phone back to LG ( who replaced the motherboard :/).
I was also on stock rom, had root and unlock bootloader (of course I clean all that **** before sending it back).
For my part, I was unable to go to recovery and download mode was quit impossible to access (may be my finger fault )
BUT! some time if I let the phone off for a moment or spam the power key, the backlight turn back on until I power down the phone, so it's could be a software issue ...
Anyway, an other info, when the backlight was off, if i tried to change backlight level i was getting a error message about overeating or something like that...
Just got my Note 10.1 2014 and was so excited to play with it and guess what? The screen is dead. I can hear it boot up and everything even the capacitive menu and back buttons make their annoying "water drop" noises and light up. Anyone know something I can do about this? I've already ordered a replacement from Amazon but would like to try and fix it meanwhile (I put 1 day shipping for a reason...). I'm really impressed with Samsung's quality control. Tinted screens, loose speaker grills, unresponsive tablets, and now one that has a screen that doesn't even work out of the box. Thanks Samsung!
notebooko said:
Just got my Note 10.1 2014 and was so excited to play with it and guess what? The screen is dead. I can hear it boot up and everything even the capacitive menu and back buttons make their annoying "water drop" noises and light up. Anyone know something I can do about this? I've already ordered a replacement from Amazon but would like to try and fix it meanwhile (I put 1 day shipping for a reason...). I'm really impressed with Samsung's quality control. Tinted screens, loose speaker grills, unresponsive tablets, and now one that has a screen that doesn't even work out of the box. Thanks Samsung!
Click to expand...
Click to collapse
This happened to me last night. My screen did eventually work, and it might've been related to it being charged. I still sent mine back to Amazon today, however.
You may want to read this thread: http://forum.xda-developers.com/showthread.php?t=2551881
When I did my RMA last night they only would do a refund since the 32 GB Black model was out of stock at Amazon, so I'm carefully reconsidering what tablet I want now... ugh.
locovaca said:
This happened to me last night. My screen did eventually work, and it might've been related to it being charged. I still sent mine back to Amazon today, however.
You may want to read this thread: http://forum.xda-developers.com/showthread.php?t=2551881
When I did my RMA last night they only would do a refund since the 32 GB Black model was out of stock at Amazon, so I'm carefully reconsidering what tablet I want now... ugh.
Click to expand...
Click to collapse
Thanks for the link. I don't know if I want to open up the back cover and risk breaking anything as of now because I only got it like an hour ago, but I'm going to try charging it fully to see if it works later. That really sucks that they don't have it in stock anymore and Samsung should really be getting a lot of **** for this. Nobody wants to spend 500-600 dollars on a tablet and have it not work after a week let alone the first hour. I have been thinking about the iPad Air, but I like the S-Pen so much I don't know what to do. Sigh, first world problems. :crying:
notebooko said:
Thanks for the link. I don't know if I want to open up the back cover and risk breaking anything as of now because I only got it like an hour ago, but I'm going to try charging it fully to see if it works later. That really sucks that they don't have it in stock anymore and Samsung should really be getting a lot of **** for this. Nobody wants to spend 500-600 dollars on a tablet and have it not work after a week let alone the first hour. I have been thinking about the iPad Air, but I like the S-Pen so much I don't know what to do. Sigh, first world problems. :crying:
Click to expand...
Click to collapse
Well, the wonderful thing (sarcasm) is that it was back in-stock this morning, but my RMA was already set up for a return and I was sending a case back too. I could probably tell Amazon to switch it back but at this point I'd rather just see this through and figure out where to go from there.
In my case I didn't remove the back. What I did initially was just plug it into the charger. At first it didn't even turn on then, but after a little bit the backlight did turn on in charging mode. Then it would work on the initial boot but not come on after it first turned off, and then after a while that ended and it just worked normally. FWIW, my battery was at 0 or 1% when I got it and around 15% when it started working completely correct, so it possibly is related to the charge level.
locovaca said:
Well, the wonderful thing (sarcasm) is that it was back in-stock this morning, but my RMA was already set up for a return and I was sending a case back too. I could probably tell Amazon to switch it back but at this point I'd rather just see this through and figure out where to go from there.
In my case I didn't remove the back. What I did initially was just plug it into the charger. At first it didn't even turn on then, but after a little bit the backlight did turn on in charging mode. Then it would work on the initial boot but not come on after it first turned off, and then after a while that ended and it just worked normally. FWIW, my battery was at 0 or 1% when I got it and around 15% when it started working completely correct, so it possibly is related to the charge level.
Click to expand...
Click to collapse
Charged it to 100% and didn't work. Oh well, my replacement will be here tomorrow. I'm pretty sure they forgot to connect the display connector or something. I can take screenshots and look at the screenshots through my computer with the tablet connected and even navigate through the menus and things. Don't know how quality control missed the tablet that didn't even have a connected display. Thanks for the help and good luck on deciding on a new tablet.
Mine arrived on Tuesday with a dead screen as well. And I had ordered mine from Samsung. Horrible customer service BTW.
Sent from a galaxy far, far away!
So something quite unfortunate happened to me last night. I factory reset my watch since I installed a new rom on my Moto G, and ever since I did that, the screen is black. Nothing else. The power button isn't doing anything regardless of how long I hold it in or whatnot, and it's just not doing anything, it's a brick. It's not rooted or boot loader unlocked or anything either. When it place it on the charging dock though, the light at the bottom of the dock lights up so I know it's charging at least, but I just really don't know what happened to it. Do you guys think it's toast?
--Edit--
So I spoke to Motorola's live assistance, and if this issue arises for anyone else, hold the power button down for about 2-3 minutes and it should boot into the bootloader, from there you can either attempt a fastboot reboot command or a normal powerup.
I tried your solution. But nothing happened. I think i have the same problem. Mine won't show anything, but when i tried charging, the light on the dock light up. Do you have any other solution? Thanks
fireball0093 said:
So something quite unfortunate happened to me last night. I factory reset my watch since I installed a new rom on my Moto G, and ever since I did that, the screen is black. Nothing else. The power button isn't doing anything regardless of how long I hold it in or whatnot, and it's just not doing anything, it's a brick. It's not rooted or boot loader unlocked or anything either. When it place it on the charging dock though, the light at the bottom of the dock lights up so I know it's charging at least, but I just really don't know what happened to it. Do you guys think it's toast?
--Edit--
So I spoke to Motorola's live assistance, and if this issue arises for anyone else, hold the power button down for about 2-3 minutes and it should boot into the bootloader, from there you can either attempt a fastboot reboot command or a normal powerup.
Click to expand...
Click to collapse
Raging_Ken said:
I tried your solution. But nothing happened. I think i have the same problem. Mine won't show anything, but when i tried charging, the light on the dock light up. Do you have any other solution? Thanks
Click to expand...
Click to collapse
I'm experiencing the issue. And my situation is same as @Raging_Ken. Is there any alternative way to manual/force restart? Since we only have 1 physical button. :crying:
presario3839 said:
I'm experiencing the issue. And my situation is same as @Raging_Ken. Is there any alternative way to manual/force restart? Since we only have 1 physical button. :crying:
Click to expand...
Click to collapse
Anybody got solutions? At this point, i have no problem for paying for replacement, the problem is i got mine from USA, and i'm from Indonesia. Huff
Raging_Ken said:
Anybody got solutions? At this point, i have no problem for paying for replacement, the problem is i got mine from USA, and i'm from Indonesia. Huff
Click to expand...
Click to collapse
Hi @Raging_Ken ! We're at the same boat. Do you any friend that have same situation as ours?
@presario3839
You also got yours from the states? I only know one other people who use the moto 360 and he also got it from the US. I'll check with him tomorrow. Can you check how much will it cost to ask for a replacement in Malaysia? Going there on middle of May, if it's cheaper, i'd rather pay the replacement there. Hehehe
presario3839 said:
I'm experiencing the issue. And my situation is same as @Raging_Ken. Is there any alternative way to manual/force restart? Since we only have 1 physical button. :crying:
Click to expand...
Click to collapse
I know it took a few tries for it to do that but at the same rate if you've tried it a few times then that's quite odd, It's also quite a pain how there's just one button to do it with. Hopefully you get it fixed, I really don't have too much else advice sadly D:
fireball0093 said:
I know it took a few tries for it to do that but at the same rate if you've tried it a few times then that's quite odd, It's also quite a pain how there's just one button to do it with. Hopefully you get it fixed, I really don't have too much else advice sadly D:
Click to expand...
Click to collapse
I just found out that motorola doesn't have any service center in South East Asia, hence we'rwe're screw. Unless somebody in this forum has an answer that can help us, the best that we can do is put it as an ornament in the bed. Huff. @presario3839
fireball0093 said:
I know it took a few tries for it to do that but at the same rate if you've tried it a few times then that's quite odd, It's also quite a pain how there's just one button to do it with. Hopefully you get it fixed, I really don't have too much else advice sadly D:
Click to expand...
Click to collapse
Raging_Ken said:
I just found out that motorola doesn't have any service center in South East Asia, hence we'rwe're screw. Unless somebody in this forum has an answer that can help us, the best that we can do is put it as an ornament in the bed. Huff. @presario3839
Click to expand...
Click to collapse
:crying: we're doomed! any acquaintance you have in this forum? Anyone can help us? @fireball0093 maybe?
I think there can be three reasons for the black screen.
1. The watch has hung and needs the 2-3 minute bottom press as posted by the OP.
2. You use Watchface or Watchface Pro like myself. It has occasionally crashed on me. After several taps, I eventually have the menu come up and can get to settings/reset. I then have the default Moto face and can reselect Watchface. Hope this bug is fixed soon.
3. Hardware failure. LCD displays have a single backlight and if it fails so does the display.
I hope it's either #1 or 2 that you are running into.
this happens to me whene android wear crashes on the watch. i was able to notice the force close notification before it went to a black screen and did not respond until the battery died. once the battery was dead i placed it back on the charger and eventually it turned on. this has only happened maybe three times since i bought the watch at launch.
SeaFractor said:
I think there can be three reasons for the black screen.
1. The watch has hung and needs the 2-3 minute bottom press as posted by the OP.
2. You use Watchface or Watchface Pro like myself. It has occasionally crashed on me. After several taps, I eventually have the menu come up and can get to settings/reset. I then have the default Moto face and can reselect Watchface. Hope this bug is fixed soon.
3. Hardware failure. LCD displays have a single backlight and if it fails so does the display.
I hope it's either #1 or 2 that you are running into.
Click to expand...
Click to collapse
I've tried #1 but failed to force restart the watch. #2 seems not applicable to me since I'm using Facer.
[Solved]
Hi,
I faced the same issue suddenly (black screen) since yesterday, i came across your thread today trying to find a solution, and tried every solution posted here (e.g. holding 2~3 min on power bottom) several times, but no success!!
I put the watch at charging dock and the charging LED in the dock is ON.... but the watch is just showing black screen ... until i thought it might be from the USB cable... so i change it with its original USB cable which comes with it in the box (while unaware; i used a cheap USB cable from the market 2 days ago while organising chargers/cables in electricity outlet, without realising that i changed the USB cables), and once i used the original USB cable... it's started to work/charge immediately.
Solved
fireball0093 said:
So something quite unfortunate happened to me last night. I factory reset my watch since I installed a new rom on my Moto G, and ever since I did that, the screen is black. Nothing else. The power button isn't doing anything regardless of how long I hold it in or whatnot, and it's just not doing anything, it's a brick. It's not rooted or boot loader unlocked or anything either. When it place it on the charging dock though, the light at the bottom of the dock lights up so I know it's charging at least, but I just really don't know what happened to it. Do you guys think it's toast?
--Edit--
So I spoke to Motorola's live assistance, and if this issue arises for anyone else, hold the power button down for about 2-3 minutes and it should boot into the bootloader, from there you can either attempt a fastboot reboot command or a normal powerup.
Click to expand...
Click to collapse
I hold the power button for 3 minutes, however nothing happened.
Soon after holding i put it back on the charger and it restarted itself and everything was perfect.
hope this works for you.
Yeah. I'm having the same issue. The only thing that allows me to turn the watch back on is to put it on the charger. Been dealing with this for a few months.
after I changed rom I can not associate my bike away bluethoot.
the Debug:
cached bluetooth device for device not found
E / bluetoothDevice (3177) getBluetoothClass () COD is 526 084
E / bluetooth Event Manager Settings (13790) Got bonding been changed fo Mac-addres wareble, but device not added into cache.
someone has this problem?
I have the same thing! Really frustrating.
If I put it on the charger there is nothing. If I put it in a "funny" way the light on the duck is on and I can even see the battery sign shown but it disappeared after a few seconds.
I used different chargers and cables and outlets in my house and other places - same thing.
I even tried a friend's charger (original moto 360 charger) but nothing.
I did try the "holding" (3 min is a bit much, no?) - nothing happens. I do have a blister on my hand from doing that 5 times
Any other ideas?
I bought this watch because I was curious and now i can't be without it. I will buy another one if there is no resolution.
I have the same issue. I put the watch aside for a few days (still haven't exhausted the battery), and then put it on its original charger, a few minutes later, the display come back! Don't know why, and don't know whether it will happen again...
When i try to start the watch, it seems to get to the watch face, but when i hit the settings, it seems to shutdown, and the only thing i can do is put back on the cradle. If i leave on the cradle it seems to work fine. What i don't understand is i have two of the same watch one black one silver, and the silver works flawless. I am wondering if i have to clear cache, or how do i collect a log of whats happening. I've tried factory reset. uninstalling aw app, nothing seems to work. Any advice is appreciated.
Thanks
I am getting same thing for last couple updates. Don't even use watch anymore Cuz it just shuts off randomly. Tried clearing everything and reinstalling, etc. No luck so far.
Same thing here, but mine shuts down during my run when I listen music off of it, around 75-80% battery, but works fine when I use it normally, without connected Bluetooth headphones
I've been getting random shutdowns for the last few months.
Sometimes I feel like it's triggered by lots of vibrating on the watch, but no correlation to battery level, most of the time it's in the 60% percentage.
I've done a factory reset and deleted and uninstalled and reinstalled android wear on the phone several times, and it always fixes it temporarily...
Sounds epidemic.
How hard was it to get a replacement?
Anybody able to find a fix? TIA
Same problem. At first I figured it was a but that came with an update and would get fixed on the next one. I stopped wearing it for a while. Now, months later, still doing it.
I got the 360 the first day it was available. I'm thinking that I'm probably out of warranty now. Should have placed a complaint when it first happened.
Has anyone found a resolution?
MarkCoburn said:
Same problem. At first I figured it was a but that came with an update and would get fixed on the next one. I stopped wearing it for a while. Now, months later, still doing it.
I got the 360 the first day it was available. I'm thinking that I'm probably out of warranty now. Should have placed a complaint when it first happened.
Has anyone found a resolution?
Click to expand...
Click to collapse
My experience is nearly identical to yours. Bought my Moto 360 on release day, it started having problems about 9 months shutting down. I factory reset, removed apps, eventually upgraded to a different phone, all the problems continued.
When I finally called Moto support, my warranty had expired, but they told me for $100 they'd replace it. I did that and just got my replacement, and I must say it's Awesome. I forgot what it was like to have a smart watch that lasts 18 hours and never shuts down regardless of how much I use it!
So, $100... you can buy a new or refurb Moto 360 for that online, so maybe it's not worth it. It's still a great smart watch IMO though. At this point I feel no need to upgrade to 2nd gen.
For the defects, this appears to be a widespread problem for Moto 360 1st gen. Best of luck to you.
still any solution
Did anyone find solution to this?
I've the same problem. In fact, it won't restart until I put if back in the cradle. On top of that, I no longer get any messaging/email notifications.
Well, about 16 months in to my replacement and it started happening again... OG Moto 360, just like the original. I suppose it's time to upgrade. Still, 16 months for $100 outdated technology smart watch worn every day isn't terrible.
I had the same issue, would randomly shut down and whenever I tried to open an app or settings it would just die. It was the battery, i found a replacement battery on ebay for around $25 replaced it and now it's working as expected.
Rick Butts said:
I had the same issue, would randomly shut down and whenever I tried to open an app or settings it would just die. It was the battery, i found a replacement battery on ebay for around $25 replaced it and now it's working as expected.
Click to expand...
Click to collapse
Wow, seriously?! I just looked, and sure enough the batteries are all over eBay. How difficult was it to replace?
not too hard to replace... Check out the instructions on YouTube... Took me about 15 minutes
Hi,
I have the gen 1 Moto 360 and I've used it pretty consistently since I got it shortly after release. I've recently started having a strange problem - if I turn the watch off (the whole thing through Settings, not the screen), it won't boot. It'll go through the Motorola "M" screen and then start on the Android Wear boot animation, but always crashes there. The screen turns off suddenly without any visible glitches or errors. I can do this all day long and it always crashes in the boot animation, though not always at the same time in it. On the other hand, if I place it in the charger (regardless of how much charge the battery has), it will automatically start booting and will make it all the way through no problem. I've tried booting through Recovery and even doing a Factory Reset but nothing seems to work other than putting it on the charger (which isn't terribly conventient unless I'm at home).
Based on some of the other threads I'm seeing this is probably a fairly minor problem (fairly easy to just not turn the watch off), but does anyone have any ideas on how to fix it (or even why putting it in the charger makes it work)?
Thanks!
Same problem being discussed here : http://forum.xda-developers.com/moto-360/help/frustrated-360-off-randomly-t3198154
this exact problem occurred with my first moto360. moto replaced it as though it were still under warranty. the replacement watch is now starting to do the same thing. looks like it is just due to battery age, like their hardware that is designed to prevent it from turning on with a "low" battery is reading it wrong. Android Wear is just unstable enough so that some days Wear doesn't respond and eventually ends with a reboot which means OFF until back at charger, even with 80-90% battery!
i had this exact problem. it was a dodgy battery, i opened the watch up and replaced the battery. Since then it has been good
Finding a good quality WX30 battery in August 2018
Are you able to share where you sourced a 'good' WX30 battery from?
I've been happy with my Moto 360 Gen 1 for exactly 2 years, until a couple of weeks ago when all the classic battery problems started (random shutdowns after a couple of hours, still 70% left, slightly bulging back). I've succeeded in learning how to get out the 4 clips, disassemble and reassemble the body, kudos = search for YouTube 'easy Moto 360 batery replacement video'.
Unless anyone has any good tips, I'm about to play the eBay battery lottery. Motorola has confirmed to me that they do not sell the batteries separately. Typical.
jonno66 said:
Are you able to share where you sourced a 'good' WX30 battery from?
I've been happy with my Moto 360 Gen 1 for exactly 2 years, until a couple of weeks ago when all the classic battery problems started (random shutdowns after a couple of hours, still 70% left, slightly bulging back). I've succeeded in learning how to get out the 4 clips, disassemble and reassemble the body, kudos = search for YouTube 'easy Moto 360 batery replacement video'.
Unless anyone has any good tips, I'm about to play the eBay battery lottery. Motorola has confirmed to me that they do not sell the batteries separately. Typical.
Click to expand...
Click to collapse
I have literally changed mine this morning... So far so good, no random dying at 70%+ and I ordered this one... https://www.ebay.co.uk/itm/163139641091
I doubt its genuine. its is 330mAh not 300mAh and is from a different manufacturer, however, its worth a tenner to see what happens! Also, how easy is the dissassembly fromt hat video, I watched the exact same one. was in peices in 10 minutes and back together quicker!
Platypus222 said:
Hi,
I have the gen 1 Moto 360 and I've used it pretty consistently since I got it shortly after release. I've recently started having a strange problem - if I turn the watch off (the whole thing through Settings, not the screen), it won't boot. It'll go through the Motorola "M" screen and then start on the Android Wear boot animation, but always crashes there. The screen turns off suddenly without any visible glitches or errors. I can do this all day long and it always crashes in the boot animation, though not always at the same time in it. On the other hand, if I place it in the charger (regardless of how much charge the battery has), it will automatically start booting and will make it all the way through no problem. I've tried booting through Recovery and even doing a Factory Reset but nothing seems to work other than putting it on the charger (which isn't terribly conventient unless I'm at home).
Based on some of the other threads I'm seeing this is probably a fairly minor problem (fairly easy to just not turn the watch off), but does anyone have any ideas on how to fix it (or even why putting it in the charger makes it work)?
Thanks!
Click to expand...
Click to collapse
I have the same problem
I leave it charging for 5 to 10 minutes and it will boot up but it also crashes and shuts down itself
I feel like the watch is selfaware
I need help
Thanks